mirror of https://github.com/hak5/openwrt.git
148 lines
2.4 KiB
Plaintext
148 lines
2.4 KiB
Plaintext
/dts-v1/;
|
|
|
|
#include "mt7620a.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "buffalo,whr-300hp2", "ralink,mt7620a-soc";
|
|
model = "Buffalo WHR-300HP2";
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
power {
|
|
label = "whr-300hp2:red:power";
|
|
gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wifi {
|
|
label = "whr-300hp2:green:wifi";
|
|
gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
power2 {
|
|
label = "whr-300hp2:green:power";
|
|
gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wifi2 {
|
|
label = "whr-300hp2:orange:wifi";
|
|
gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
internet {
|
|
label = "whr-300hp2:green:internet";
|
|
gpios = <&gpio2 17 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
router {
|
|
label = "whr-300hp2:green:router";
|
|
gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
router2 {
|
|
label = "whr-300hp2:orange:router";
|
|
gpios = <&gpio2 19 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
gpio-keys-polled {
|
|
compatible = "gpio-keys-polled";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
poll-interval = <20>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
|
|
aoss {
|
|
label = "aoss";
|
|
gpios = <&gpio2 13 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
};
|
|
|
|
ap {
|
|
label = "ap";
|
|
gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_0>;
|
|
linux,input-type = <EV_SW>;
|
|
};
|
|
|
|
bridge {
|
|
label = "bridge";
|
|
gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_0>;
|
|
linux,input-type = <EV_SW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&gpio2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
m25p80@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <10000000>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@30000 {
|
|
label = "u-boot-env";
|
|
reg = <0x30000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@40000 {
|
|
label = "factory";
|
|
reg = <0x40000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@50000 {
|
|
label = "firmware";
|
|
reg = <0x50000 0x7b0000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pinctrl {
|
|
state_default: pinctrl0 {
|
|
gpio {
|
|
ralink,group = "i2c", "uartf", "rgmii1", "rgmii2", "wled", "nd_sd";
|
|
ralink,function = "gpio";
|
|
};
|
|
};
|
|
};
|
|
|
|
ðernet {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&ephy_pins>;
|
|
mediatek,portmap = "llllw";
|
|
};
|
|
|
|
&gsw {
|
|
mediatek,port4 = "ephy";
|
|
};
|
|
|
|
&wmac {
|
|
ralink,mtd-eeprom = <&factory 0>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pa_pins>;
|
|
};
|