mirror of https://github.com/hak5/openwrt.git
124 lines
1.8 KiB
Plaintext
124 lines
1.8 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "ar9331.dtsi"
|
|
|
|
/ {
|
|
aliases {
|
|
serial0 = &uart;
|
|
led-boot = &system;
|
|
led-failsafe = &system;
|
|
led-running = &system;
|
|
led-upgrade = &system;
|
|
};
|
|
|
|
gpio-keys-polled {
|
|
compatible = "gpio-keys-polled";
|
|
poll-interval = <20>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
system: system {
|
|
label = "tl-wr703n:blue:system";
|
|
gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
reg_usb_vbus: reg_usb_vbus {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "usb_vbus";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
enable-active-high;
|
|
};
|
|
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
num-cs = <1>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
uboot: partition@0 {
|
|
reg = <0x0 0x20000>;
|
|
label = "u-boot";
|
|
read-only;
|
|
};
|
|
|
|
firmware: partition@20000 {
|
|
reg = <0x20000 0x3d0000>;
|
|
label = "firmware";
|
|
};
|
|
|
|
art: partition@3f0000 {
|
|
reg = <0x3f0000 0x10000>;
|
|
label = "art";
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
mtd-mac-address = <&uboot 0x1fc00>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
|
|
switch-phy-addr-swap = <0>;
|
|
switch-phy-swap = <0>;
|
|
};
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
compatible = "syscon", "simple-mfd";
|
|
};
|
|
|
|
&gpio {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb {
|
|
dr_mode = "host";
|
|
vbus-supply = <®_usb_vbus>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_phy {
|
|
status = "okay";
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&uboot 0x1fc00>;
|
|
};
|