Commit Graph

2667 Commits (ffd249366f96a6a94fac18909109a6c98a458de7)

Author SHA1 Message Date
Adrian Schmutzler ee5fce887a ramips: consolidate MAC address cases in 02_network
This just merges some duplicate definitions and consolidates lines.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com> [merge duplicated
cases for phicomm k2p]
2019-07-25 21:59:57 +08:00
Adrian Schmutzler f14a5c3f2f ramips: use kiB instead of B for IMAGE_SIZE
This cosmetical patch is just meant to make comparing/checking
IMAGE_SIZE values easier.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:34 +02:00
Adrian Schmutzler 9d87a58d34 ramips: remove ralink_default_fw_size_xxx variables
There are frequent examples of the ralink_default_fw_size_xxx
variables being used to "roughly" set flash size without caring
about the actual size of the firmware partition.

To discourage this behavior, this patch removes the variables and
just sets IMAGE_SIZE by its numeric value for each target.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:30 +02:00
Adrian Schmutzler 363197311b ramips: remove default IMAGE_SIZE for ramips target
Currently, ramips target defines 0x7b0000 as default IMAGE_SIZE
for all devices in ramips target, i.e. this will be set if a
device does not specify IMAGE_SIZE itself.

From 92 devices using that default due to a "missing" IMAGE_SIZE,
14 were incorrect by a small amount (i.e. still "8M" flash) and
12 were completely off ("16M", "4M", ...).

This patch thus removes the _default_ IMAGE_SIZE and defines
IMAGE_SIZE for each device individually. This should indicate to
people supporting new devices that this parameter has to be cared
about.

For the present code, this patch is cosmetical.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:27 +02:00
Adrian Schmutzler 24ded1810b ramips/rt305x: fix IMAGE_SIZE for all devices
This fixes IMAGE_SIZE for all devices based on the partition size
given in DTS:

DEVICE                       *.MK    *.DTS     VERDICT
7links_px-4885-4m            (4M)    0x3b0000
7links_px-4885-8m            -       0x7b0000  default
8devices_carambola           -       0x7b0000  default
accton_wr6202                -       0x7b0000  default
airlive_air3gii              (4M)    0x3b0000
alfa-network_w502u           -       0x7b0000  default
allnet_all0256n-4m           (4M)    0x3b0000
allnet_all0256n-8m           -       0x7b0000  default
allnet_all5002               32448k  0x1fb0000
allnet_all5003               32448k  0x1fb0000
alphanetworks_asl26555-16m   15872k  0xf80000
alphanetworks_asl26555-8m    7744k   0x790000
arcwireless_freestation5     -       0x7b0000  default
argus_atp-52b                7808k   0x7a0000
asiarf_awapn2403             (4M)    0x3b0000
asiarf_awm002-evb-4m         (4M)    0x3b0000
asiarf_awm002-evb-8m         -       0x7b0000  default
asus_rt-g32-b1               (4M)    0x3b0000
asus_rt-n10-plus             (4M)    0x3b0000
asus_rt-n13u                 -       0x7b0000  default
asus_wl-330n                 (4M)    0x3b0000
asus_wl-330n3g               (4M)    0x3b0000
aximcom_mr-102n              -       0x790000  wrong
aztech_hw550-3g              -       0x7b0000  default
belkin_f5d8235-v2            7744k   0x790000
belkin_f7c027                7616k   0x770000
buffalo_whr-g300n            3801088 0x3a0000
dlink_dap-1350               7488k   0x750000
dlink_dcs-930                (4M)    0x3b0000
dlink_dcs-930l-b1            (4M)    0x3b0000
dlink_dir-300-b1             (4M)    0x3b0000
dlink_dir-300-b7             (4M)    0x7b0000  wrong
dlink_dir-320-b1             -       0x7b0000  default
dlink_dir-600-b1             (4M)    0x3b0000
dlink_dir-610-a1             (4M)    0x3b0000
dlink_dir-615-d              (4M)    0x3b0000
dlink_dir-615-h1             (4M)    0x3b0000
dlink_dir-620-a1             -       0x7b0000  default
dlink_dir-620-d1             -       0x7b0000  default
dlink_dwr-512-b              7800k   0x7e0000  wrong
easyacc_wizard-8800          -       0x7b0000  default
edimax_3g-6200n              3648k   0x390000
edimax_3g-6200nl             3648k   0x390000
engenius_esr-9753            (4M)    0x3b0000
fon_fonera-20n               -       0x7b0000  default
hame_mpr-a1                  (4M)    0x3b0000
hame_mpr-a2                  -       0x7b0000  default
hauppauge_broadway           7744k   0x790000
hilink_hlk-rm04              -       0x3b0000  wrong
hootoo_ht-tm02               -       0x7b0000  default
huawei_d105                  (4M)    0x3b0000
huawei_hg255d                15744k  0xf60000
intenso_memory2move          -       0x7b0000  default
jcg_jhr-n805r                (4M)    0x3b0000
jcg_jhr-n825r                (4M)    0x3b0000
jcg_jhr-n926r                (4M)    0x3b0000
mofinetwork_mofi3500-3gn     -       0x7b0000  default
netcore_nw718                3712k   0x3a0000
netgear_wnce2001             (4M)    0x350000  wrong
nexaira_bc2                  -       0x7b0000  default
nexx_wt1520-4m               (4M)    0x3b0000
nexx_wt1520-8m               -       0x7b0000  default
nixcore_x1-16m               16064k  0xfb0000
nixcore_x1-8m                7872k   0x7b0000
olimex_rt5350f-olinuxino     -       0x7b0000  default
olimex_rt5350f-olinuxino-evb -       0x7b0000  default
omnima_miniembplug           -       0x7b0000  default
omnima_miniembwifi           -       0x7b0000  default
petatel_psr-680w             (4M)    0x3b0000
planex_mzk-dp150n            (4M)    0x3b0000
planex_mzk-w300nh2           3648k   0x390000
planex_mzk-wdpr              -       0x680000  wrong
poray_ip2202                 -       0x7b0000  default
poray_m3                     (4M)    0x3b0000
poray_m4-4m                  (4M)    0x3b0000
poray_m4-8m                  -       0x7b0000  default
poray_x5                     -       0x7b0000  default
poray_x8                     -       0x7b0000  default
prolink_pwh2004              -       0x7b0000  default
ralink_v22rw-2x2             (4M)    0x3b0000
sitecom_wl-351               (4M)    0x3b0000
skyline_sl-r7205             (4M)    0x3b0000
sparklan_wcr-150gn           (4M)    0x3b0000
teltonika_rut5xx             -       0xfb0000  wrong
tenda_3g150b                 (4M)    0x3b0000
tenda_3g300m                 (4M)    0x3b0000
tenda_w150m                  (4M)    0x3b0000
tenda_w306r-v2               (4M)    0x3b0000
trendnet_tew-638apb-v2       (4M)    0x3b0000
trendnet_tew-714tru          -       0x7b0000  default
unbranded_a5-v11             (4M)    0x3b0000
unbranded_wr512-3gn-4m       (4M)    0x3b0000
unbranded_wr512-3gn-8m       -       0x7b0000  default
unbranded_xdx-rn502j         (4M)    0x3b0000
upvel_ur-326n4g              (4M)    0x3b0000
upvel_ur-336un               -       0x7b0000  default
vocore_vocore-16m            16064k  0xfb0000
vocore_vocore-8m             7872k   0x7b0000
wansview_ncs601w             -       0x7b0000  default
wiznet_wizfi630a             (16M)   0xfb0000
zorlik_zl5900v2              -       0x7b0000  default
zyxel_keenetic               (4M)    0x3b0000
zyxel_keenetic-start         (4M)    0x3b0000
zyxel_nbg-419n               (4M)    0x3b0000
zyxel_nbg-419n-v2            (8M)    0x7b0000

No verdict means that the device is correctly set.

Legend:
( ): Value is set via ralink_default_fw_size_xxM
[ ]: Value is derived from parent definition
 - : Value is not set and derived from default definition

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:23 +02:00
Adrian Schmutzler 1c611f1617 ramips/rt288x,rt3883: fix IMAGE_SIZE for all devices
This fixes IMAGE_SIZE for all devices based on the partition size
given in DTS:

DEVICE                 *.MK    *.DTS      VERDICT
airlink101_ar670w      (4M)    0x3c0000   wrong
airlink101_ar725w      -       0x3B0000   wrong
asus_rt-n15            (4M)    0x3b0000
belkin_f5d8235-v1      7744k   0x7b0000   wrong
buffalo_wli-tx4-ag300n (4M)    0x3b0000
buffalo_wzr-agl300nh   (4M)    0x3b0000
dlink_dap-1522-a1      3801088 0x3a0000
ralink_v11st-fe        (4M)    0x003b0000

asus_rt-n56u           -       0x007b0000 default
belkin_f9k1109v1       7224k   0x7a0000   wrong
dlink_dir-645          -       0x7b0000   default
edimax_br-6475nd       7744k   0x00790000
loewe_wmdr-143n        -       0x7b0000   default
omnima_hpm             16064k  0x00fb0000
samsung_cy-swr1100     -       0x7b0000   default
sitecom_wlr-6000       7244k   0x713000
trendnet_tew-691gr     -       0x007b0000 default
trendnet_tew-692gr     -       0x007b0000 default

No verdict means that the device is correctly set.

Legend:
( ): Value is set via ralink_default_fw_size_xxM
[ ]: Value is derived from parent definition
 - : Value is not set and derived from default definition

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:18 +02:00
Adrian Schmutzler 439435f59b ramips/mt76x8: fix IMAGE_SIZE for all devices
This fixes IMAGE_SIZE for all devices based on the partition size
given in DTS:

DEVICE                       *.MK   *.DTS     VERDICT
alfa-network_awusfree1       (8M)   0x7b0000
buffalo_wcr-1166ds           -      0x7c0000  wrong
cudy_wr1000                  (8M)   0x7b0000
d-team_pbr-d1                (16M)  0x0fb0000
duzun_dm06                   -      0x7b0000  default
glinet_gl-mt300n-v2          16064k 0xfb0000
glinet_vixmini               7872k  0x7b0000
hilink_hlk-7628n             (32M)  0x1fb0000
hiwifi_hc5661a               (16M)  0xf70000  wrong
hiwifi_hc5861b               15808k 0xf70000
mediatek_linkit-smart-7688   (32M)  0x1fb0000
mediatek_mt7628an-eval-board (4M)   0x7b0000  wrong
mercury_mac1200r-v2          -      0x7c0000  wrong
netgear_r6120                15744k 0xf60000
onion_omega2                 (16M)  0xfb0000
onion_omega2p                (32M)  0x1fb0000
rakwireless_rak633           -      0x7b0000  default
skylab_skw92a                16064k 0xfb0000
tama_w06                     15040k 0xeb0000
totolink_lr1200              7872k  0x7b0000
tplink_archer-c20-v4         7808k  0x7a0000
tplink_archer-c50-v3         7808k  0x7a0000
tplink_archer-c50-v4         7616k  0x770000
tplink_tl-mr3020-v3          7808k  0x7a0000
tplink_tl-mr3420-v5          7808k  0x7a0000
tplink_tl-wa801nd-v5         7808k  0x7a0000
tplink_tl-wr802n-v4          7808k  0x7a0000
tplink_tl-wr840n-v4          7808k  0x7a0000
tplink_tl-wr840n-v5          3904k  0x3d0000
tplink_tl-wr841n-v13         7808k  0x7a0000
tplink_tl-wr841n-v14         3968k  0x3e0000
tplink_tl-wr842n-v5          7808k  0x7a0000
tplink_tl-wr902ac-v3         7808k  0x7a0000
unielec_u7628-01-128m-16m    16064k 0xfb0000
vocore_vocore2               (16M)  0xfb0000
vocore_vocore2-lite          (16M)  0x7b0000  wrong
wavlink_wl-wn570ha1          (8M)   0x7b0000
wavlink_wl-wn575a3           (8M)   0x7b0000
widora_neo-16m               (16M)  0x0fb0000
widora_neo-32m               (32M)  0x1fb0000
wiznet_wizfi630s             (32M)  0x1fb0000
wrtnode_wrtnode2p            (16M)  0x1fb0000 wrong
wrtnode_wrtnode2r            (16M)  0x1fb0000 wrong
xiaomi_mir4a-100m            14976k 0xea0000
xiaomi_miwifi-nano           (16M)  0xfb0000
zbtlink_zbt-we1226           (8M)   0x7b0000
zyxel_keenetic-extra-ii      14912k 0xe90000

No verdict means that the device is correctly set.

Legend:
( ): Value is set via ralink_default_fw_size_xxM
[ ]: Value is derived from parent definition
 - : Value is not set and derived from default definition

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:15 +02:00
Adrian Schmutzler 7263838e69 ramips/mt7621: fix IMAGE_SIZE for all devices
This fixes IMAGE_SIZE for all devices based on the partition size
given in DTS:

DEVICE                     *.MK     *.DTS     VERDICT
afoundry_ew1200            (16M)    0xfb0000
asiarf_ap7621-001          (16M)    0xfa0000  wrong
buffalo_wsr-1166dhp        (16M)    0xf90000  wrong
buffalo_wsr-600dhp         (16M)    0xfb0000
dlink_dir-860l-b1          (16M)    0xfb0000
d-team_newifi-d2           (32M)    0x1fb0000
d-team_pbr-m1              (16M)    0xfb0000
elecom_wrc-1167ghbk2-s     15488k   0xf20000
elecom_wrc-1900gst         11264k   0xb00000
elecom_wrc-2533gst         11264k   0xb00000
firefly_firewrt            (16M)    0xfb0000
gehua_ghl-r-001            (32M)    0x1fb0000
gnubee_gb-pc1              (32M)    0x1fb0000
gnubee_gb-pc2              (32M)    0x1fb0000
hiwifi_hc5962              (32M)    0x2000000 wrong (kernel + ubi)
iodata_wn-ax1167gr         15552k   0xf30000
iodata_wn-gx300gr          7798784  0x770000
lenovo_newifi-d1           (32M)    0x1fb0000
linksys_re6500             -        0x7b0000  default
mediatek_ap-mt7621a-v60    (8M)     0x7b0000
mediatek_mt7621-eval-board (4M)     0xec0000  wrong (rootfs)
mikrotik_rb750gr3          [16128k] 0xfc0000
mikrotik_rbm11g            [16128k] 0xFC0000
mikrotik_rbm33g            [16128k] 0xFC0000
mqmaker_witi-256m          (16M)    0xfb0000
mqmaker_witi-512m          (16M)    0xfb0000
mtc_wr1201                 16000k   0xfa0000
netgear_ex6150             14848k   0xe80000
netgear_r6220              28672k   0x1c00000
netgear_r6350              40960k   0x2800000
netgear_wndr3700-v5        15232k   0xee0000
netis_wf-2881              129280k  0x7E40000
phicomm_k2p                15744k   0xf60000
planex_vr500               66453504 0x3fb0000 wrong
samknows_whitebox-v8       (16M)    0xfb0000
storylink_sap-g3200u3      -        0x7b0000  default
telco-electronics_x1       16064k   0xfb0000
thunder_timecloud          -        0xfb0000  wrong
totolink_a7000r            16064k   0xfb0000
tplink_re350-v1            6016k    0x5e0000
ubiquiti_edgerouterx       -        0xfa00000 wrong (kernel1 + ubi)
ubiquiti_edgerouterx-sfp   -        0xfa00000 wrong (kernel1 + ubi)
unielec_u7621-06-256m-16m  16064k   0xfb0000
unielec_u7621-06-512m-64m  65216k   0x3fb0000
wevo_11acnas               (16M)    0xfb0000
wevo_w2914ns-v2            (16M)    0xfb0000
xiaomi_mir3g               32768k   0x7980000 wrong (kernel + ubi)
xiaomi_mir3p               (32M)    0xf980000 wrong (kernel + ubi)
xzwifi_creativebox-v1      (32M)    0x1fb0000
youhua_wr1200js            16064k   0xfb0000
youku_yk-l2                (16M)    0xfb0000
zbtlink_zbt-we1326         (16M)    0xfb0000
zbtlink_zbt-we3526         (16M)    0xfb0000
zbtlink_zbt-wg2626         (16M)    0xfb0000
zbtlink_zbt-wg3526-16m     (16M)    0xfb0000
zbtlink_zbt-wg3526-32m     (32M)    0x1fb0000

No verdict means that the device is correctly set.

Legend:
( ): Value is set via ralink_default_fw_size_xxM
[ ]: Value is derived from parent definition
 - : Value is not set and derived from default definition

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:11 +02:00
Adrian Schmutzler 7009f407f1 ramips/mt7620: fix IMAGE_SIZE for all devices
This fixes IMAGE_SIZE for all devices based on the partition size
given in DTS:

DEVICE                     *.MK     *.DTS      VERDICT
aigale_ai-br100            7936k    0x7c0000
alfa-network_ac1200rm      16064k   0xfb0000
alfa-network_tube-e4g      16064k   0xfb0000
asus_rp-n53                -        0x7b0000   default
asus_rt-ac51u              (16M)    0xfb0000
asus_rt-n12p               -        0xfb0000   wrong
asus_rt-n14u               -        0xfb0000   wrong
bdcom_wap2100-sk           15808k   0xf70000
buffalo_whr-1166d          15040k   0xfb0000   wrong
buffalo_whr-300hp2         6848k    0x7b0000   wrong
buffalo_whr-600d           6848k    0x7b0000   wrong
buffalo_wmr-300            -        0x7b0000   default
comfast_cf-wr800n          -        0x7b0000   default
dlink_dch-m225             6848k    0x6b0000
dlink_dir-510l             -        0xde0000   wrong
dlink_dir-810l             6720k    0x690000
dlink_dwr-116-a1           -        0x7e0000   wrong
dlink_dwr-118-a1           -        0xfe0000   wrong
dlink_dwr-118-a2           -        0xfe0000   wrong
dlink_dwr-921-c1           (16M)    0xfe0000   wrong
dlink_dwr-921-c3           [(16M)]  0xfe0000   wrong
dlink_dwr-922-e2           (16M)    0xfe0000   wrong
dovado_tiny-ac             -        0x7b0000   default
edimax_br-6478ac-v2        7616k    0x00790000 wrong
edimax_ew-7476rpc          7744k    0x00790000
edimax_ew-7478ac           7744k    0x00790000
edimax_ew-7478apc          7744k    0x00790000
elecom_wrh-300cr           (16M)    0xdf0000   wrong
glinet_gl-mt300a           (16M)    0xf80000   wrong
glinet_gl-mt300n           (16M)    0xf80000   wrong
glinet_gl-mt750            (16M)    0xf80000   wrong
head-weblink_hdrm200       16064k   0xfb0000
hiwifi_hc5661              15872k   0xf80000
hiwifi_hc5761              15872k   0xf80000
hiwifi_hc5861              15872k   0xf80000
hnet_c108                  16777216 0xfb0000   wrong
iodata_wn-ac1167gr         6864k    0x6b4000
iodata_wn-ac733gr3         6992k    0x6d4000
kimax_u25awf-h1            16064k   0xfb0000
kimax_u35wf                16064k   0xfb0000
kingston_mlw221            15744k   0xf60000
kingston_mlwg2             15744k   0xf60000
lava_lr-25g001             -        0xfe0000   wrong
lenovo_newifi-y1           (16M)    0xfb0000
lenovo_newifi-y1s          (16M)    0xfb0000
linksys_e1700              -        0x7b0000   default
microduino_microwrt        16128k   0xfc0000
netgear_ex2700             (4M)     0x3b0000
netgear_ex3700             7744k    0x790000
netgear_wn3000rp-v3        -        0x7b0000   default
nexx_wt3020-4m             (4M)     0x3b0000
nexx_wt3020-8m             -        0x7b0000   default
ohyeah_oy-0001             (16M)    0xfb0000
phicomm_k2g                7552k    0x760000
phicomm_psg1208            -        0x7b0000   default
phicomm_psg1218a           -        0x7b0000   default
phicomm_psg1218b           -        0x7b0000   default
planex_cs-qr10             -        0x7b0000   default
planex_db-wrt01            -        0x7b0000   default
planex_mzk-750dhp          -        0x7b0000   default
planex_mzk-ex300np         -        0x730000   wrong
planex_mzk-ex750np         -        0x730000   wrong
ralink_mt7620a-evb         -        0x7b0000   default
ralink_mt7620a-mt7530-evb  -        0x7b0000   default
ralink_mt7620a-mt7610e-evb -        0x7b0000   default
ralink_mt7620a-v22sg-evb   -        0x7f80000  wrong
ravpower_wd03              (8M)     0x7b0000
sanlinking_d240            (16M)    0xfb0000
sercomm_na930              20m      0x1400000
tplink_archer-c20i         -        0x7a0000   wrong
tplink_archer-c20-v1       -        0x7a0000   wrong
tplink_archer-c2-v1        -        0x7a0000   wrong
tplink_archer-c50-v1       -        0x7a0000   wrong
tplink_archer-mr200        -        0x7b0000   default
vonets_var11n-300          (4M)     0x3b0000
wrtnode_wrtnode            (16M)    0xfb0000
xiaomi_miwifi-mini         (16M)    0xf80000   wrong
youku_yk1                  (32M)    0x1fb0000
yukai_bocco                -        0x7b0000   default
zbtlink_we1026-5g-16m      16777216 0xfb0000   wrong
zbtlink_zbt-ape522ii       -        0xf80000   wrong
zbtlink_zbt-cpe102         -        0x760000   wrong
zbtlink_zbt-wa05           -        0x760000   wrong
zbtlink_zbt-we2026         -        0x760000   wrong
zbtlink_zbt-we826-16m      (16M)    0xfb0000
zbtlink_zbt-we826-32m      (32M)    0x1fb0000
zbtlink_zbt-we826-e        32448k   0x1fb0000
zbtlink_zbt-wr8305rt       -        0x7b0000   default
zte_q7                     -        0x7b0000   default
zyxel_keenetic-omni        -        0x7b0000   default
zyxel_keenetic-omni-ii     -        0x7b0000   default
zyxel_keenetic-viva        16064k   0xfb0000

No verdict means that the device is correctly set.

Legend:
( ): Value is set via ralink_default_fw_size_xxM
[ ]: Value is derived from parent definition
 - : Value is not set and derived from default definition

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:08 +02:00
Adrian Schmutzler a6cd311b0b ramips: support IMAGE_SIZE in kiB for Build/trx
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:05 +02:00
Adrian Schmutzler 7392af7520 ramips: fix ralink_default_fw_size_16M
In ramips, there are the following predefined values for IMAGE_SIZE
ralink_default_fw_size_4M    3866624   3776k   0x3B0000
ralink_default_fw_size_8M    8060928   7872k   0x7B0000
ralink_default_fw_size_16M  16121856  15744k   0xF60000
ralink_default_fw_size_32M  33226752  32448k  0x1FB0000

Out of those, the "16M" value is obviously odd, as it provides more
room for the remaining partitions than the tree others.
Of the devices in all subtargets, there are actually > 50 that have
a firmware partition with 0xFB0000 size, while only 5 (!) have
0xF60000. From the former, many are set to
ralink_default_fw_size_16M anyway, although it is wrong at the
present point.

Consequently, it makes sense to change ralink_default_fw_size_16M
to 0xFB0000, and to update IMAGE_SIZE for the 5 devices with
0xF60000.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:01 +02:00
Adrian Schmutzler b9cf1f6081 ramips/rt305x: fix firmware partition size for some 4MB devices
allnet_all0256n-4m, tenda_w150m and unbranded_wr512-3gn-4m have
their firmware partition set to reg = <0x50000 0x3c8000>.

However, based on the 4MB flash, the size should be 0x3b0000.

After some research in the target's history, it looks like the
changed size has been a mistake when transferring device
partitions from Makefile to DTS in 770b28f146.

This patch changes the named three devices back to 0x3b0000.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:30:57 +02:00
Chuanhong Guo f30d588460 ramips: fix mac addresses used by Phicomm K2P
Like most mt7621 boards, Phicomm K2P stores LAN/WAN mac addresses
at 0xe000/0xe006 of factory partition.
Phicomm uses lan_mac-1 as wan_mac, while our default case in 02_network
uses lan_mac+1.

Add a special case reading lan/wan mac address for Phicomm K2P.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-07-25 19:59:33 +08:00
Roger Pueyo Centelles 7d684b7673 ramips: add kmod-mt7615e to Phicomm K2P images
Now that the mt76 driver supports the MT7615D chip found on these
devices, use it.

Also add the wpad-basic package.

Note: the driver supports operation on both the 2.4 GHz and the
      5 GHz bands, but not yet concurrently.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-07-25 18:24:50 +08:00
DENG Qingfang 0e6d97f961 ramips: enable Newifi D1 SD slot
Newifi D1 is shipped with an 8GB microSD card in its SD slot
Without SD driver users would not be able to use it unless manually installed

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2019-07-23 13:14:07 +08:00
Rafał Miłecki 1cbe0d659c treewide: sysupgrade: get rid of platform_nand_pre_upgrade()
1) nand_do_upgrade() is always called by a target code
2) nand_do_upgrade() starts with calling platform_nand_pre_upgrade()

It means there is no need for the platform_nand_pre_upgrade() callback
at all. All code that was present there could bo moved & simplly called
by a target right before the nand_do_upgrade().

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-07-22 14:27:37 +02:00
Georgi Vlaev 8c51ddeff0 ramips: add support for TP-Link RE650 v1
TP-Link RE650 v1 is a dual-band AC2600 range extender,
based on MediaTek MT7621A and MT7615E. According to the
wikidevi entry for RE650 this device is identical with
TP-Link RE500 as hardware. This patch supports only RE650.

Hardware specification:

- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
  Serial console @ 57600,8n1

Flash instructions:

Upload
openwrt-ramips-mt7621-tplink_re650-v1-squashfs-factory.bin
from the RE650 web interface.

TFTP recovery to stock firmware:

Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.

Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
[re-added variables for kernel header]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-07-17 23:14:23 +02:00
INAGAKI Hiroshi cda123fe69 ramips: add MT7615 wireless support for ELECOM WRC-1167GHBK2-S
ELECOM WRC-1167GHBK2-S has a MediaTek MT7615D chip for 2.4/5 GHz
wireless.

A driver package for MT7615 chip is added to OpenWrt in
a0e5ca4f35,
so add preliminary MT7615 chip support for WRC-1167GHBK2-S.

Note: Currently, DBDC mode for MT7615 is not supported in mt76 driver.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-07-17 14:45:18 +02:00
Rafał Miłecki 8b4bc7abe0 treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()
stage2 passes image path to platform_do_upgrade() as an argument so it
can be simply accessed using $1

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-07-17 08:05:38 +02:00
Rafał Miłecki d9593b0809 ramips: get rid of platform_pre_upgrade()
The only step between platform_pre_upgrade() and platform_do_upgrade()
is switching to ramdisk. It should be fine to "mtd erase firmware" from
the later callback and get rid of the first one.

This change wasn't tested on affected target but identical code logic
was verified to work as expected on brcm47xx with initramfs firmware.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-07-16 19:03:42 +02:00
Adrian Schmutzler 6d61fcfa9e ramips: Remove left-over mistyped device string from 02_network
In 2011 (!), network setup for nexaira,bc2 was moved to network
defaults script with a typo so it became b2c:
295e04084c ("ramips: setup bc2 mac addresses from the generic network script")

This patch just removes the useless entry without replacement,
since it seems to have worked for 8 years anyway.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-16 11:33:46 +08:00
Chuanhong Guo fae125781e ramips: mtk-mmc: mt76x8: check ESD_MODE before applying AGPIO_CFG
Since mt76x8an ver1 eco2, SDXC pins can be switched to the
following pinmap:
sd_d1  -> PAD_I2S_SDI
sd_d0  -> PAD_I2S_WS
sd_cmd -> PAD_I2S_CLK
sd_d3  -> PAD_I2C_SCLK
sd_d2  -> PAD_I2C_SD
sd_clk -> PAD_GPIO0
sd_wp  -> PAD_TXD1
sd_cd  -> PAD_RXD1

To use this pinmap, one would need to set ESD_MODE bit (bit 15)
to 1 in GPIO1_MODE and switch other used pads into GPIO mode.
In this mode, we don't need to switch ethernet pins to digital
pad.

Check ESD_MODE bit before applying AGPIO_CFG and use rt_sysc_m32
to set it.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-07-16 09:50:16 +08:00
David Bauer 14e0e4f138 ramips: add support for ASUS RT-AC57U
SoC:   MediaTek MT7621AT
RAM:   128M (Winbond W631GG6KB-15)
FLASH: 16MB (Spansion S25FL128SA)
WiFi:  MediaTek MT7603EN bgn 2SS
WiFi:  MediaTek MT7612EN nac 2SS
BTN:   Reset - WPS
LED:    - Power
        - LAN {1-4}
        - WAN
        - WiFi 2.4 GHz
        - WiFi 5 GHz
        - USB
UART:  UART is present next to the Power LED.
       TX - RX - GND - 3V3 / 57600-8N1
       3V3 is the nearest one to the Power LED.

Installation
------------
Via TFTP:
1. Set your computers IP-Address to 192.168.1.75.
2. Power up the Router with the Reset button pressed.
3. Release the Reset button after 5 seconds.
4. Upload OpenWRT sysupgrade image via TFTP:
 > tftp -4 -v -m binary 192.168.1.1 -c put <IMAGE>

Via SSH:
Note: User/password for SSH is identical with the one used in the
Web-interface.
1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt sysupgrade image via scp:
 > scp owrt.bin admin@192.168.1.1:/tmp
4. Connect via SSH to the router.
 > ssh admin@192.168.1.1
5. Write the OpenWrt image to flash.
 > mtd-write -i /tmp/owrt.bin -d linux
6. Reboot the router
 > reboot

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-07-11 21:32:39 +02:00
Chuanhong Guo 53daa51cf2 ramips: fix mqmaker witi case in fixup-mac-address
This commit fixes a forgotten case in previous commit.

Fixes: 087e14ab59 ("ramips: mt7621: merge two variants of MQmaker WiTi together")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-07-11 23:27:06 +08:00
Chuanhong Guo 087e14ab59 ramips: mt7621: merge two variants of MQmaker WiTi together
Since we can auto-detect memory now, we don't need 2 dts for two
memory variants.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-07-11 22:11:21 +08:00
Chuanhong Guo a2c19f1d2f ramips: dts: drop memory nodes
mt7621 and mt7628 now have the ability to detect memory size
automatically.
Drop memory nodes and let kernel determine memory size.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-07-11 22:11:21 +08:00
Chuanhong Guo 6d91ddf517 ramips: mt7621: add support for memory detection
mt7621 has the following memory map:
0x0-0x1c000000: lower 448m memory
0x1c000000-0x2000000: peripheral registers
0x20000000-0x2400000: higher 64m memory

detect_memory_region in arch/mips/kernel/setup.c only add the first
memory region and isn't suitable for 512m memory detection because
it may accidentally read the memory area for peripheral registers.

This commit adds memory detection capability for mt7621:
1. add the highmem area when 512m is detected.
2. guard memcmp from accessing peripheral registers:
     This only happens when some weird user decided to change
     kernel load address to 256m or higher address. Since this
     is a quite unusual case, we just skip 512m testing and return
     256m as memory size.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-07-11 22:11:21 +08:00
Daniel Golle 98d04dc4cf ramips: fix bogus MTK_SOC (typo)
Belkin F7C027 is clearly Rt5350 SoC, as shown on internal
photographs filed for FCC approval[1].

[1]: https://fcc.io/K7S/F7C027

Fixes commit 3b0264eddb
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-07-10 19:28:35 +02:00
Adrian Schmutzler 447deed52a ramips: Sort all subtarget Makefiles
This patch applies sorting to the definitions as whole blocks.

Sorting has been performed fully automatic, line count differences
originate from double empty lines removed.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler 5d50155f14 ramips: Reapply sorting to board.d files
This patch is cosmetical:
It only applies sorting based on device names, whereas renames
already took place in earlier patches.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler e8d2d97498 ramips: Remove base-files/lib/ramips.sh
Having converted the target to use device compatible, ramips.sh
is obsolete now.

The only remaining entry for the mt7688 evaluation board seems to
be orphaned.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler 3b0264eddb ramips/rt305x: Name DTS files based on scheme
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler 6a104ac772 ramips/rt288x,rt3883: Name DTS files based on scheme
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler b97a99256f ramips/mt76x8: Name DTS files based on scheme
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler 7196ca1d49 ramips/mt7621: Name DTS files based on scheme
As introduced with ath79, DTS files for ramips will now be labelled
soc_vendor_device.dts(i). With this change, DTS files can be
selected automatically without further manual links.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler 48047b3a5c ramips/mt7620: Name DTS files based on scheme
As introduced with ath79, DTS files for ramips will now be labelled
soc_vendor_device.dts(i). With this change, DTS files can be
selected automatically without further manual links.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler 402138d12d ramips: Derive DTS name from device name in Makefile
This will automatically derive the DTS name as in ath79 and thus
makes specifying DTS for every device obsolete.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

---

This patch only introduces the mechanism and is then followed by
commits with renames and Makefile adjustments per subtarget.

Eventually, those can be all squashed into a single commit or left
as they are to enhance overview.
2019-07-10 17:36:29 +02:00
Adrian Schmutzler 7dd3a234be ramips/rt305x: Synchronize Makefiles with DTS compatible
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler 83efa8329b ramips/rt288x,rt3883: Synchronize Makefiles with DTS compatible
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler c2334ad60d ramips/mt76x8: Synchronize Makefiles with DTS compatible
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler 2f2a319f82 ramips/mt7621: Synchronize Makefiles with DTS compatible
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler 9f99000165 ramips/mt7620: Synchronize Makefiles with DTS compatible
This will "rename" devices in Makefiles to the pattern used in
DTS compatible. This will systematize naming of devices
enormously.

As device names are used to for default SUPPORTED_DEVICES entries,
we need to adjust the source for /tmp/sysinfo/board_name, too.
So remove relevant entries from base-files/lib/ramips.sh and
use device compatible for that.

Despite that, base-files are updated, too.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler d93969a13a ramips: Improve compatible for TP-Link Archer devices
Include "Archer" in compatible as it is part of the device name.

Update Makefile device names where necessary to match compatible.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:28 +02:00
Daniel Golle c2b1baf767 ramips: add missing DEVICE_VENDOR
Fixes commit ee66fe4ea9
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-07-10 17:15:49 +02:00
Chuanhong Guo 7a8d3432c7 ramips: use upstream RAW_APPENDED_DTB instead of our OWRTDTB
Upstream kernel added support for RAW_APPENDED_DTB on ralink arch
in the following commit:
02564fc89d3d ("ralink: Introduce fw_passed_dtb to arch/mips/ralink")

Use upstream solution and get rid of our OWRTDTB hack.
This commit set DEVICE_DTS to $$(DTS) instead of replacing DTS with
DEVICE_DTS in device profile because DTS variable will be dropped
in later commits.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on mt7621/mt76x8]
Tested-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on rt305x/mt7620]
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-07-08 22:00:24 +02:00
Adrian Schmutzler c017ead66e ramips: Fix compatible for YUKAI Engineering BOCCO
Looks like an undetected copy/paste error.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-07 13:02:05 +02:00
Daniel Golle ee66fe4ea9 ramips: convert DEVICE_TITLE to new variables
Also unify naming and add details where they were missing.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-07-06 14:58:03 +02:00
Alexander Müller 3fd97c522b
ramips: add support for TP-Link TL-WR841n v14
TP-Link TL-WR841n v14 is a router based on MediaTek MT7628N.

- MediaTek MT7628NN
- 32 MB of RAM
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet

Installation:
- copy the
  'openwrt-ramips-mt76x8-tl-wr841n-v14-squashfs-tftp-recovery.bin'
  file to your tftp server root and rename it to 'tp_recovery.bin'.
- configure your PC running the TFTP server with the static IP address
  192.168.0.66/24
- push the reset button and plug in the power connector. Wait until
  the orange led starts blinking (~6sec)

Signed-off-by: Alexander Müller <donothingloop@gmail.com>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu> [small modifications gpio-hog]
2019-07-02 16:17:49 +02:00
Alexander Couzens cc1147072d ramips/leds: use devicetree alias led_wlan
Similiar to the lantiq target use a dts alias to define the wlan led
instead of static mapping in /etc/board.d/01_leds. Reduce code
duplication.
A device tree must define the alias "led-wlan" similiar to "led-boot".

/ {
        aliases {
                led-wlan = &led_wlan;
        };

        [..]

        led_wlan: wlan {
            label = "tl-wr841n-v14:green:wlan";
            gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
        };
};

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2019-07-02 16:05:28 +02:00
Chuanhong Guo 3f68cffd27 ramips: add support for TOTOLINK A7000R
Specifications:
- SoC: MT7621AT
- RAM: 128MB
- Flash: 16M SPI NOR
- Ethernet: 5x GE ports
- WiFi: 2.4G: MT7615N
        5G: MT7615N

Flash instruction:
Upload generated sysupgrade firmware through factory web interface.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-06-26 07:41:54 +02:00
Chuanhong Guo 110daa16e4 ramips: mt7621: add IRQ for GPIO node
This makes interrupt-based gpio-keys working.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-06-26 07:41:54 +02:00
Daniel Danzberger 029c970464 ramips: mt7621: Add new device AsiaRF AP7621-001
Hardware specs:
SoC:	Mediatek MT7621A
CPU:	4x 880Mhz
Cache:	32 KB I-Cache and 32 KB D-Cach
	256 KB L2 Cache (shared by Dual-Core)
RAM:	DDR3 512MB 16bits BUS
FLASH:	16MB
Switch:	Mediatek Gigabit Switch (1 x LAN, 1 x WAN)
USB:	1x 3.0
PCI:	3x Mini PCIe
GPS:	Quectel L70B
BTN:	Reset
LED:	- Power
	- Ethernet
	- Wifi
	- USB
UART:	UART is present as Pads with throughholes on the PCB.
	They are located on left side.
	3.3V - RX - GND - TX / 57600-8N1
	3.3V is the square pad

Installation:
The stock image is a modified openwrt and can be overflashed via
 # sysupgrade -F image.bin

Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[removed unused label, formatting]
2019-06-25 15:02:21 +02:00
Koen Vandeputte 6592dddd15 kernel: bump 4.14 to 4.14.128
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-20 15:48:48 +02:00
Petr Štetiar 783e37502f ramips: fix EW-7478AC model name in DTS
This fixes lower case AC in the DTS model name.

Fixes: 88f7a29f99 ("ramips: add support for Edimax EW-7476RPC / EW-7478AC")
Reported-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-20 12:47:19 +02:00
Pawel Dembicki eeeaf24e28 ramips: fix GELAN port in D-Link DWR-118-A2
This patch fix and enable GELAN port in D-LINK DWR-118-A2.

Tested-by: Richard Toth <trtk1992@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-06-20 08:48:20 +02:00
Pawel Dembicki 391df37829 ramips: mt7620: add EPHY base mdio address changing possibility
In some boards is requred to change the ephy mdio base address.

This patch add of property "mediatek,ephy-base-address" in gsw
part, which allows to change ephy base address.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[fixed indentation in header file]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-20 08:48:19 +02:00
Pawel Dembicki c02a9a2514 ramips: mt7620: fix external PHY autopolling
The port initialisation is based on assumption that phy address and
port number is the same. SoC allow different numbers and some board
have it.

Use phy address instead the port number to make sure that correct
addresses are polled.

In situation when only one PHY with address 0x0 is conected to
port 4, autopolling is broken.

This patch make autopolling correct when port number and phy address
are different.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-06-20 08:48:19 +02:00
Mathias Kresin f96c7f697f ramips: handle mdio address and switch port seperate
The phy handling code forces a phy mdio address and the switch port to
which a phy is attached to be the same. Albeit such a configuration is
used for most boards, it isn't for all.

Pass the switch port number to the ethernet phy connect functions, to
ensure the correct list entry is edited and not the list entry that
matches th phys mdio address.

Use the mdio address with mdiobus_get_phy instead of the port number,
to make sure the expected ethernet phy gets connected.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-06-20 08:48:19 +02:00
Mathias Kresin fb423f6e01 ramips: ignore already handled ethernet phys
The whole logic in fe_phy_connect() is based on the asumption that mdio
address and switch port id are equal. Albeit it is true for most
boards, it doesn't is for all.

It isn't yet clear which subtargets/boards require the devicetree less
ethernet phy handling. Hence change the code in a way that it doesn't
touch ethernet phys which were early attached and are already handled.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-06-20 08:48:19 +02:00
Birger Koblitz ab7f8146fd ramips: add support for Edimax EW-7478APC
SoC:	MediaTek MT7620a @ 580MHz
RAM:	64M (Winbond W9751G6KB-25)
FLASH:	8MB (Macronix)
WiFi:	SoC-integrated: MediaTek MT7620a bgn
WiFi:	MediaTek MT7612EN nac
Switch: Mediatek MT7530W Gigabit Switch (4 x LAN, 1 x WAN)
USB:	Yes 1 x 2.0 (+ 1 x 2.0 unpopulated header)
BTN:	Reset/WPS
LED:    - Power (white)
	- Internet (blue)
	- Wifi (blue)
	- USB (blue)
UART:  UART is present as Pads with throughholes on the PCB. They are
       located in the lower right corner (GbE ports facing up)
       3.3V - RX - GND - TX / 57600-8N1
       3.3V is the square pad

Installation
------------
Update the factory image via the web-interfaces (by default:
http://edimax.setup)

Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[merge conflicts in 01_leds and mt7620.mk, dts whitespace issues]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-20 08:48:19 +02:00
Birger Koblitz 88f7a29f99 ramips: add support for Edimax EW-7476RPC / EW-7478AC
SoC:	MediaTek MT7620a @ 580MHz
RAM:	64M (Winbond W9751G6KB-25)
FLASH:	8MB (Macronix)
WiFi:	SoC-integrated: MediaTek MT7620a bgn
WiFi:	MediaTek MT7612EN nac
GbE:	1x (RTL8211E)
BTN:	WPS - RFKILL/RF 50%/RF 100% toggle
LED:	- Wifi 5g (blue)
	- Wifi 2g (blue)
	- Crossband (green)
	- Power (green)
	- WPS (green)
	- LAN (Green)
UART:	UART is present as Pads with throughholes on the PCB. They are
	located next to the switch for the wifi configuration
	3.3V - RX - GND - TX / 57600-8N1
	3.3V is the square pad

Installation
------------
Update the factory image via the web-interfaces (by default:
192.168.9.2/24).
http://192.168.9.2/index.asp

ramips: add Edimax EW-7478AC

SoC:	MediaTek MT7620a @ 580MHz
RAM:	64M (Winbond W9751G6KB-25)
FLASH:	8MB (Macronix)
WiFi:	SoC-integrated: MediaTek MT7620a bgn
WiFi:	MediaTek MT7612EN nac
GbE:	1x (RTL8211E)
BTN:	WPS - RFKILL/RF 50%/RF 100% toggle
LED:	- Wifi 5g (blue)
	- Wifi 2g (blue)
	- Crossband (green)
	- Power (green)
	- WPS (green)
	- LAN (Green)
UART:	UART is present as Pads with throughholes on the PCB. They are
	located next to the switch for the wifi configuration
	3.3V - RX - GND - TX / 57600-8N1
	3.3V is the square pad

Installation
------------
Update the factory image via the web-interfaces (by default:
http://edimaxext.setup)
Or push wpa button on power on and send firmware via tftp to 192.168.1.6

The EW-7478AC is identical to the EW-7476RPC, except instead of 2 internal
antennas it has 2 external ones.

Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[merge conflict in 01_leds]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-20 08:31:24 +02:00
Koen Vandeputte a7e68927d0 kernel: bump 4.14 to 4.14.125 (FS#2305 FS#2297)
Refreshed all patches.

This bump contains upstream commits which seem to avoid (not properly fix)
the errors as seen in FS#2305 and FS#2297

Altered patches:
- 403-net-mvneta-convert-to-phylink.patch
- 410-sfp-hack-allow-marvell-10G-phy-support-to-use-SFP.patch

Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-12 15:04:09 +02:00
Kristian Evensen 86b6d31e6e ramips: Remove redundant LED-cases
01_leds has several redundant LED-cases. This commit cleans
up the file by merging these cases into shared cases.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-06-10 11:25:47 +02:00
Deng Qingfang b47cf6d539 ramips: mt7620: select kmod-rt2800-pci driver for RT5592
ASUS RP-N53 and Buffalo WHR-600D use RT5592 for 5GHz wireless
After commit 367813b9b1 the driver for RT5592 (rt2800pci)
is not selected by default anymore, which broke their 5GHz wireless
Add it back to device packages

Fixes: 367813b9b1 ("ramips: mt7620: fix dependencies")

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2019-06-10 11:25:47 +02:00
Chuanhong Guo 0ab9f283f7 ramips: add support for TOTOLINK LR1200
Specifications:
- SoC: MT7628DAN (MT7628AN with 64MB built-in RAM)
- Flash: 8M SPI NOR
- Ethernet: 5x 10/100Mbps
- WiFi: 2.4G: MT7628 built-in
        5G: MT7612E
- 1x miniPCIe slot for LTE modem (only USB pins connected)
- 1x SIM slot

Flash instruction:
U-boot has a builtin web recovery page:
1. Hold the reset button while powering it up
2. Connect to the ethernet and set an IP in 192.168.1.0/24 range
3. Open your browser and upload firmware through http://192.168.1.1

Note about the LTE modem:
If your router comes with an EC25 module and it doesn't show up
as a QMI device, you should do the following to switch it to QMI
mode:
1. Install kmod-usb-serial-option and a terminal software
   (e.g. minicom or screen). All 4 serial ports of the modem
   should be available now.
2. Open /dev/ttyUSB3 with the terminal software and type this
   AT command: AT+QCFG="usbnet",0
3. Power-cycle the router. You should now get a QMI device
   recognized.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-06-05 10:26:33 +02:00
Pawel Dembicki 9b7abd9fe2 ramips: mt7620: fix 5GHz WiFi LED on DWR-118-A1
Support for D-Link DWR-118 A1 was added before LEDs feature
in mt76x0e driver.

This fixes the 5GHz WiFi LED which was previously inverted.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-06-05 10:12:30 +02:00
Petr Štetiar bf58bc3bd8 ramips: ethernet: remove unused SIOCETHTOOL ioctl handling
This ioctl is currently routed through generic interface code.

  dev_ioctl
    dev_ethtool
      __ethtool_get_link_ksettings
        phy_ethtool_ioctl

Cc: Felix Fietkau <nbd@nbd.name>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-05 10:12:30 +02:00
Jan Hoffmann 085f66de9a ramips: create R6220 dtsi and improve WNDR3700v5 support
The R6220 and WNDR3700v5 are identical apart from using NAND/NOR flash and
having a different casing. This adds a new cleaned up R6220.dtsi with the
common bits for both devices. Both devices now have feature parity.

Performed cleanup:
 * generic DTS node names
 * regulator for usb power
 * added missing pinctrl groups
 * use switch port instead of VLAN as trigger for WAN LED

Fixes for WNDR3700v5:
 * all LEDS work
 * correct ethernet MAC addresses

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2019-05-31 11:21:22 +02:00
Markus Scheck 5ff5c9bce6 ramips: add support for Xiaomi Mi Router 4A (100M Edition)
- SoC:      MediaTek MT7628AN
- Flash:    16MB (Winbond W25Q128JV)
- RAM:      64MB
- Serial:   As marked on PCB, 3V3 logic, baudrate is 115200
- Ethernet: 3x 10/100 Mbps (switched, 2x LAN + WAN)
- WIFI0:    MT7628AN 2.4GHz 802.11b/g/n
- WIFI1:    MT7612EN 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs:     Programmable power-LED (two-colored, yellow/blue)
            Non-programmable internet-LED (shows WAN-activity)
- Buttons:  Reset

INSTALLATION:

1. Connect to the serial port of the router and power it up.
   If you get a prompt asking for boot-mode, go to step 3.
2. Unplug the router after
       > Erasing SPI Flash...
       > raspi_erase: offs:20000 len:10000
   occurs on the serial port. Plug the router back in.
3. At the prompt select option 2 (Load system code then
   write to Flash via TFTP.)
4. Enter 192.168.1.1 as the device IP and 192.168.1.2 as the
   Server-IP.
5. Connect your computer to LAN1 and assign it as 192.168.1.2/24.
6. Rename the sysupgrade image to test.bin and serve it via TFTP.
7. Enter test.bin on the serial console and press enter.

Signed-off-by: Markus Scheck <markus@mscheck.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added mt76 compatible]
2019-05-31 11:21:22 +02:00
Davide Fioravanti 7c91144ae6 ramips: add CUDY WR1000 support
Cudy WR1200 is an AC1200 AP with 3-port FE and 2 non-detachable antennas

Specifications:

MT7628 (580 MHz)
64 MB of RAM (DDR2)
8 MB of FLASH
2T2R 2.4 GHz (MT7628)
2T2R 5 GHz (MT7612E)
3x 10/100 Mbps Ethernet (2 LAN + 1 WAN)
2x external, non-detachable antennas (5dbi)
UART header on PCB (57600 8n1)
7x LED, 2x button

Known issues:
The Power LED is always ON, probably because it is connected
directly to power.

Flash instructions
------------------
Load the ...-factory.bin image via the stock web interface.

Openwrt upgrade instructions
----------------------------
Use the ...-sysupgrade.bin image for future upgrades.

Revert to stock FW
------------------
Warning! This tutorial will work only with the following OEM FW:
  WR1000_EU_92.122.2.4987.201806261618.bin
  WR1000_US_92.122.2.4987.201806261609.bin
If in the future these firmwares will not be available anymore,
you have to find the new XOR key.

1) Download the original FW from the Cudy website.

   (For example WR1000_EU_92.122.2.4987.201806261618.bin)

2) Remove the header.

   dd if="WR1000_EU_92.122.2.4987.201806261618.bin" of="WR1000_EU_92.122.2.4987.201806261618.bin.mod" skip=8 bs=64

3) XOR the new file with the region key.

   FOR EU: 7B76741E67594351555042461D625F4545514B1B03050208000603020803000D
   FOR US: 7B76741E675943555D5442461D625F454555431F03050208000603060007010C

   You can use OpenWrt's tools/firmware-utils/src/xorimage.c tool for this:

   xorimage -i WR1000..bin.mod -o stock-firmware.bin -x -p 7B767..

   Or, you can use this tool (CHANGE THE XOR KEY ACCORDINGLY!):
   https://gchq.github.io/CyberChef/#recipe=XOR(%7B'option':'Hex','string':''%7D,'',false)

4) Check the resulting decrypted image.

   Check if bytes from 0x20 to 0x3f are:
   4C 69 6E 75 78 20 4B 65 72 6E 65 6C 20 49 6D 61 67 65 00 00 00 00 00 00 00 00 00 00 00 00 00 00

   Alternatively, you can use u-boot's tool dumpimage tool to check
   if the decryption was successful. It should look like:

   # dumpimage -l stock-firmware.bin
   Image Name:   Linux Kernel Image
   Created:      Tue Jun 26 10:24:54 2018
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    4406635 Bytes = 4303.35 KiB = 4.20 MiB
   Load Address: 80000000
   Entry Point:  8000c150

5) Flash it via forced firmware upgrade and don't "Keep Settings"

   CLI: sysupgrade -F -n stock-firmware.bin

   LuCI: make sure to click on the "Keep settings" checkbox
         to disable it. You'll need to do this !TWICE! because
         on the first try, LuCI will refuse the image and reset
	 the "Keep settings" to enable. However a new
         "Force upgrade" checkbox will appear as well.
         Make sure to do this very carefully!

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added wifi compatible, spiffed-up the returned to stock instructions]
2019-05-31 10:36:36 +02:00
Davide Fioravanti 62ce6d58f2 ramips: unify JCG helper command definition
This patch makes the JCG helper command definition available
for every rampis target

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2019-05-31 10:30:03 +02:00
Nicholas Smith 73e0f52b6e ramips: add support for Telco Electronics X1
Hardware:
SoC:   MT7621
DRAM:  256MB DDR3
Flash: 16MB SPI-NOR
WiFi:  2.4GHz: MT7603 @ PCIe0
WiFi:  5.8GHz: MT7612 @ PCIe1
Modem: Sierra Wireless MC74xx

Interfaces:
GBE RJ45 x5
mPCIe    x2
UART     x1
I2C      x1
JTAG     x1
UIM      x1
LEDs     x6

Flash instructions:
Flash from within the factory bootloader, firmware web interface or CLI using
sysupgrade -F -n

Signed-off-by: Nicholas Smith <mips171@icloud.com>
2019-05-18 17:59:49 +02:00
Jan Hoffmann 2fdd02cc7c ramips: add factory image for WNDR3700v5
This uses the existing rules for Sercomm factory images and moves them
to the ramips image Makefile, so they can be used in all subtargets.

The new factory image for WNDR3700v5 can be flashed using nmrpflash.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2019-05-18 16:44:41 +02:00
Liu Yu 671c9d16e3 ramips: add support for HILINK HLK-7628N
Specification:

CPU:       MT7628 580 MHz. MIPS 24K
RAM:       128 MB
Flash:     32 MB
WIFI:      802.11n/g/b 20/40 MHz
Ethernet:  5 Port ethernet switch
UART:      2x

Flash instruction:
The U-boot is based on Ralink SDK so we can flash the firmware using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART0 line as described on the PCB.
4. Power up the device and press 2, follow the instruction to
   set device and tftp server IP address and input the firmware
   file name. U-boot will then load the firmware and write it into
   the flash.
5. After firmware is started connect via ethernet at 192.168.1.1

Signed-off-by: Liu Yu <f78fk@live.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed dupped subject]
2019-05-18 13:43:55 +02:00
Kristian Evensen 869376710d ramips: Add support for ZBT WE826-E
ZBT WE826-E is a dual-SIM version of the ZBT WE826. The router has the
following specifications:

- MT7620A (580 MHz)
- 128MB RAM
- 32MB of flash (SPI NOR)
- 5x 10/100Mbps Ethernet (MT7620A built-in switch)
- 1x microSD slot
- 1x miniPCIe slot (only USB2.0 bus)
- 2x SIM card slots (standard size)
- 1x USB2.0 port
- 1x 2.4GHz wifi (rt2800)
- 10x LEDs (4 GPIO-controlled)
- 1x reset button

The following have been tested and working:
- Ethernet switch
- wifi
- miniPCIe slot
- USB port
- microSD slot
- sysupgrade
- reset button

Installation and recovery:

In order to install OpenWRT the first time or recover the router, you
can use the web-based recovery system. Keep the reset button pressed
during boot and access 192.168.1.1 in your browser when your machine
obtains an IP address.  Upload the firmware to start the recovery
process.

How to swap SIMs:

You control which SIM slot to use by writing 0/1 to
/sys/class/gpio/gpio13/value. In order for the change to take effect,
you can either use AT-commands (AT+CFUN) or power-cycle the modem (write
0/1 to /sys/class/gpio/gpio14/value).

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-05-17 21:41:43 +02:00
Kristian Evensen 52b59a984f ramips: Add support for Head Weblink HDRM200
Head Weblink HDRM200 is a dual-sim router based on MT7620A. The detailed
specifications are:

- MT7620A (580MHz)
- 64MB RAM
- 16MB of flash (SPI NOR)
- 6x 10/100Mbps Ethernet (MT7620A built-in switch)
- 1x microSD slot
- 1x miniPCIe slot (only USB2.0 bus). Device is shipped with a SIMCOM
SIM7100E LTE modem.
- 2x SIM slots (standard size)
- 1x USB2.0 port
- 1x 2.4GHz wifi (rt2800)
- 1x 5GHz wifi (mt7612)
- 1x reset button
- 1x WPS button
- 3x GPIO-controllable LEDs
- 1x 10 pin terminal block (RS232, RS485, 4 x GPIO)

Tested:
- Ethernet switch
- Wifi
- USB slot
- SD card slot
- miniPCIe-slot
- sysupgrade
- reset button

Installation instructions:

Installing OpenWRT for the first time requires a bit of work, as the
board does not ship with OpenWRT. In addition, the bootloader
automatically reboots when installing an image over tftp. In order to
install OpenWRT on the HDRM200, you need to do the following:

* Copy the initramfs-image to your tftp-root (default filename is
test.bin) and configure networking accordingly (default server IP is
10.10.10.3, client 10.10.10.123). Start your tftp server.
* Open the board and connect to UART. The pins are exposed and clearly
marked.
* Boot the board and press 1.
* Either use the default filename and client/server IP-addresses, or
specify your own.

The image should now be loaded to memory and board boot. If the router
reboots while the image is loading, you need to try again. Once the
board has booted, copy the sysupgrade-image to the router and run
sysupgrade in order to install OpenWRT to the flash.

Notes:

- You control which SIM slot to use by writing 0/1 to
/sys/class/gpio/gpio0/value. In order for the change to take
effect, you can either use AT-commands (AT+CFUN) or power-cycle the
modem (write 0/1 to /sys/class/gpio/gpio21/value).
- RS485 is available on /dev/ttyS0.
- RS232 is available on /dev/ttyS1.
- The name of the ioX-gpios map to the labels on the casing.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[fixed whitespace issue and merge conflict in target.mk]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-05-17 21:41:43 +02:00
Koen Vandeputte 09050b6fe2 kernel: bump 4.14 to 4.14.118
Refreshed all patches.

Remove upstreamed:
- 060-v5.1-serial-ar933x_uart-Fix-build-failure-with-disabled-c.patch

Altered:
- 143-gpio-fix-device-tree-gpio-hogs-on-dual-role-gpio-pin.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-05-13 19:17:41 +02:00
David Bauer a4dc519888 ramips: fix R6120 factory image
The factory firmware omits the JFFS2 end-marker while flashing via
web-interface. Add a 64k padding after the marker fixes this problem.

When the end-marker is not present, OpenWRT won't save the overlayfs
after initial flash.

Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-05-11 16:37:11 +02:00
Deng Qingfang 367813b9b1 ramips: mt7620: fix dependencies
MT7620 integrated WMAC does not need RT2x00 PCI driver or firmware
Also corrected kmod-eeprom-93cx6 and kmod-lib-crc-itu-t dependencies
according to original Kconfig and lsmod output

This will remove some unnecessary packages from MT7620 target to
save some space

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[75 characters per line in the commit message]
2019-05-11 01:05:11 +02:00
Eike Feldmann 9e0fb5a27f ramips: add support for Rakwireless RAK633
It's OEM module with 2*26 pin header, similar to LinkIt Smart 7688 or
Vocore2.

Specification:

CPU:       MT7628 580 MHz. MIPS 24K
RAM:       64 MB
Flash:     8 MB
WIFI:      802.11n/g/b 20/40 MHz
USB:       1x Port USB 2.0
Ethernet:  5 Port ethernet switch
UART:      2x

Installation: Use the installed uboot Bootloader. Connect a serial cable
to serialport 0. Turn power on.  Choose the option: "Load system code
then write to Flash via TFTP".  Choose the local device IP and the TFTP
server IP and the file name of the system image.  After if the
Bootloader will copy the image to the local flash.

Notes: The I2C Kernel module work not correctly. You can send and
receive data. But the command i2cdetect doesn’t work. FS#845

Signed-off-by: Eike Feldmann <eike.feldmann@outlook.com>
[commit subject and message touches, DTS whitespace fixes, wifi LED
rename, pinctrl fixes, network settings fixes, lan/wmac mac addresses,
removed i2c kernel modules]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-14 23:42:03 +02:00
David Bauer 43e8c37cb4 ramips: add support for GL.iNet VIXMINI
Hardware
--------
SoC:   MediaTek MT7628NN
RAM:   64M DDR2 (Etron EM68B16CWQD-25H)
FLASH: 8M (Winbond W25Q64JVSIQ)
LED:   Power - WLAN
BTN:   Reset
UART:  115200 8N1
       TX and RX are labled on the board as pads next to the SoC

Installation via web-interface
------------------------------
1. Visit the web-interface at 192.168.8.1
   Note: The ethernet port is by default WAN. So you need to connect to
   the router via WiFi

2. Navigate to the Update tab on the left side.

3. Select "Local Update"

4. Upload the OpenWrt sysupgrade image.
   Note: Make sure you select not to preserve the configuration.

Installation via U-Boot
-----------------------
1. Hold down the reset button while powering on the device.
   Wait for the LED to flash 5 times.

2. Assign yourself a static IPv4 in 192.168.1.0/24

3. Upload the OpenWrt sysupgrade image at 192.168.1.1.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-04-13 18:46:40 +02:00
Daniel Golle 66e2acad9c ramips: fix pinctrl to allow hardware i2c on WRTNODE2R
Instead of assigning I2C pins as GPIOs by default, leave it up to the
user whether to install kmod-i2c-mt7621 and use them for hardware I2C
instead.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-04-11 22:26:28 +02:00
Kip Porterfield b812a7fa68 ramips: correct DTS for Belkin F9K1109v1 to include switch definition
Add switch definition for the rtl8367b switch to the DTS/DTSi for
the Belkin F9K1109v1 that was mistakenly omitted from the initial
commit.

Fixes: 017ec068e3df (ramips: add support for Belkin F9K1109v1)
Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
2019-04-06 19:14:06 +02:00
Chuanhong Guo d80a1c6e2c ramips: backport mt7621-spi from linux-next-20190329
Upstream driver has gone through a series of cleanup and was moved
from drivers/staging into drivers/spi. Backport it to replace our
messy driver.

Tested-by: Jörg Schüler-Maroldt <joerg-linux@arcor.de>
[LinkIt Smart 7688, AcSIP AI7688H Wi-Fi module]
Tested-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Tian Xiao bo <peterwillcn@gmail.com>
[Newifi-D2 MediaTek MT7621 ver:1 eco:3]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-04-06 19:14:06 +02:00
David Bauer b19c48dc34 ramips: enable R6120 USB power
Enable the USB power for the Netgear R6120. Otherwise, no power is
supplied to an attached USB device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-04-06 19:14:06 +02:00
Zhao Yu 32689e93c4 ramips: add support for Youku YK-L2
Hardware spec:

CPU: MTK MT7621A
RAM: 256MB
ROM: 16MB SPI Flash
WiFi: MT7603EN + MT7612EN
Button: 2 buttons (reset, wps)
LED: 8 LEDs (Power 2G 5G WPS Internet LAN1 LAN2 USB)
Ethernet: 3 ports, 2 LAN + 1 WAN
Other: USB3.0

Flashing instructions:

Visit the openwrt forum topic for this router:
https://forum.openwrt.org/t/add-openwrt-support-for-youku-yk-l2/34692

to get the bootloader and unlock firmware.

0. upgrade your router with the telnet firmware via the
   firmware upgrade page on the webui.

1. telnet 192.168.11.1 from your PC

2. Download the pb-boot-youku_l2-20190317-61b6d33.bin and transfer
   it to the /tmp directory of the router.

3. mtd write /tmp/pb-boot-youku_l2-20190317-61b6d33.bin Bootloader

4. turn off the power

5. Push the reset button while turning on the router and
   wait until LED start blinking (~10sec.)

6. Connect Ethernet port and goto http://192.168.1.1.

7. Upload the firmware to firmware restore page in webui.

Signed-off-by: Zhao Yu <574249312@qq.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [rewrote the
flashing instructions, fixed author]
2019-04-06 19:13:49 +02:00
Felix Fietkau c9262a96d1 ramips: implement vlan rx offload on MT7621
Avoids the overhead of software VLAN untagging in the network stack

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-04-03 10:40:09 +02:00
David Bauer 38f3433420 ramips: add missing SPDX identifier for EX6150
This adds the SPDX license identifier for the NETGEAR EX6150. It was
missed when submitting the original patch.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-03-31 20:59:08 +02:00
Rosen Penev 2159b25466 ramips: Increase GB-PC1 SPI frequency to 80MHz
The specific flash chip used (W25Q256FVEM) accepts 50MHz for read
requests and higher for others. 104MHz for fast reads. ramips seems to
be limited to 80MHz based on testing with higher values (no speedup).

Based on upstream commit: 97738374a310b9116f9c33832737e517226d3722

 time dd if=/dev/mtdblock3 of=/dev/null bs=64k from 42.96s to 7.01s

 [test done with backported upstream v4.19 driver[1], for numbers on
  stock 4.14 driver please take a look at `ramips: Increase GB-PC2 SPI
  frequency to 80MHz` commit message]

1. https://github.com/openwrt/openwrt/pull/1578

Signed-off-by: Rosen Penev <rosenp@gmail.com>
[expanded note about spi driver version]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 09:01:46 +01:00
Rosen Penev 274439b780 ramips: Increase GB-PC2 SPI frequency to 80MHz
The flash chip on the board (Spansion S25FL256SAIF00) is rated to
support at least 50MHz for normal read requests according to the
datasheet. 133MHz for fast reads. However, ramips seems to be limited to
80MHz.

>From testing this, higher values do not improve speeds.

time dd if=/dev/mtdblock3 of=/dev/null bs=64k from

42.82s to 14.09s.

boot speed is also faster:
[   66.884087] procd: - init - vs
[   48.976049] procd: - init -

Since spi speed was requested:
[    3.538884] spi-mt7621 1e000b00.spi: sys_freq: 225000000

CPU is 900MHz:
[    0.000000] CPU Clock: 900MHz

Signed-off-by: Rosen Penev <rosenp@gmail.com>
[fixed commit message by adding missing 0 in the spi-mt7621 clock output]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 09:01:23 +01:00
David Bauer 3f019bf96c ramips: add Netgear EX6150
SoC:   MediaTek MT7621
RAM:   64M (Winbond W9751G6KB-25)
FLASH: 16MB (Macronix MX25L12835F)
WiFi:  MediaTek MT7662E bgn 2SS
WiFi:  MediaTek MT7662E nac 2SS
BTN:   ON/OFF - Reset - WPS - AP/Extender toggle
LED:    - Arrow Right (blue)
        - Arrow Left (blue)
        - WiFi 1 (red/green)
        - WiFi 2 (red/green)
        - Power (green/amber)
        - WPS (Green)
UART:  UART is present as Pads on the backside of the PCB. They are
       located on the other side of the Ethernet port.
       3.3V - GND - TX - RX / 57600-8N1
       3.3V is the nearest one to the antenna connectors

Installation
------------
Update the factory image via the Netgear web-interfaces (by default:
192.168.1.250/24).

You can also use the factory image with the nmrpflash tool.
For more information see https://github.com/jclehner/nmrpflash

Signed-off-by: David Bauer <mail@david-bauer.net>
[merge conflict in 02_network, flash@0 node rename, wlan DTS triggers]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 07:34:00 +00:00
Vladimir Kot 58becdb30d ramips: add support for ZyXEL Keenetic Start
Device specification:
- SoC: RT5350F
- CPU Frequency: 360 MHz
- Flash Chip: Winbond 25Q32 (4096 KiB)
- RAM: 32768 KiB
- 5x 10/100 Mbps Ethernet (4x LAN, 1x WAN)
- 1x external, non-detachable antenna
- UART (J1) header on PCB (57800 8n1)
- Wireless: SoC-intergated: 2.4GHz 802.11bgn
- USB: None
- 3x LED, 2x button

Flash instruction:
1. Configure PC with static IP 192.168.1.2/24 and start TFTP server.
2. Rename "openwrt-ramips-rt305x-kn_st-squashfs-sysupgrade.bin"
   to "kstart_recovery.bin" and place it in TFTP server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed until power LED start blinking.
4. Router will download file from TFTP server, write it to flash and reboot.

Signed-off-by: Vladimir Kot <vova28rus@gmail.com>
[fixed git commit author and whitespace issues in DTS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 07:34:00 +00:00
Tobias Welz 7c4b85ee27 ramips: add support for WIZnet WizFi630S board
The WIZnet WizFi630S board is in the miniPCIe form factor.

SoC: Mediatek MT7688AN
RAM: 128MB
Flash: 32Mb
WiFi: 2.4GHz
Ethernet: 3x 100Mbit
USB: 1 (USB 2.0)
serial ports: 2 (1x full, 1xlite)

Flash and recovery instructions: Use the factory installed u-boot boot
loader. It is available on UART2 (115200,8,n,1).  Then get the
sysupgrade image from a tftp server.

Signed-off-by: Tobias Welz <tw@wiznet.eu>
[whitespace and device name in makefile fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 07:33:59 +00:00
Koen Vandeputte af6c86dbe5 kernel: bump 4.14 to 4.14.108
Refreshed all patches.

Altered patches:
- 950-0033-i2c-bcm2835-Add-debug-support.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-27 10:48:59 +01:00
Felix Fietkau bee7ff7cf3 ramips: allow packets with ttl=0
Some broken ISPs (e.g. Comcast) send DHCPv6 packets with hop limit=0.
This trips up the TTL=0 check in the PPE if enabled.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-03-24 12:10:15 +01:00
Pawel Dembicki 67fced9ba3 ramips: add support for DLINK DIR-510L
The DIR-510L Wireless Router are based on the MT7620A SoC.

Specification:

-MediaTek MT7620A (580 Mhz)
-128 MB of RAM
-16 MB of FLASH
-802.11bgn radio
-1x 10/100 Mbps Ethernet
-2x internal, non-detachable antennas
-UART (J3) header on PCB (57600 8n1)
-1x bi-color LED (GPIO-controlled), 2x button
-JBOOT bootloader

Known issues:
-Ethernet port is used as LAN
-No communication with charger IC. (uart bitbang needed)

Installation:
Apply factory image via d-link http web-gui.

How to revert to OEM firmware:
1.) Push the reset button and turn on the power. Wait until LED start blinking (~10sec.)
2.) Upload original factory image via JBOOT http (IP: 192.168.123.254)
3.) If http doesn't work, it can be done with curl command:
    curl -F FN=@XXXXX.bin http://192.168.123.254/upg
    where XXXXX.bin is name of firmware file.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[fixed whitespace issue in 10-rt2x00-eeprom]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-24 01:44:24 +01:00
Pawel Dembicki 1f149fcad3 firmware-utils: mkdlinkfw: add kernel image offset
Some boards with JBOOT have partiton between bootloader
and kernel image. This patch add possibility to change kernel
partition start address.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-03-24 01:44:24 +01:00
Qin Wei 5f40b519f3 ramips: fix wrong i2s clock unit from kHz to MHz
clk_get_rate returns the current clock rate in Hz for a clock source so
if we divide it by 1M, then we get frequency in MHz and not kHz.

Signed-off-by: Qin Wei <support@vocore.io>
[added missing commit message, and fixed author with SoB from PR message]
Signed-off-by: Petr Štetiar <ynezz@true.cz>

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-24 01:44:24 +01:00
Adrian Schmutzler 4269914187 ramips: Speed up eeprom read/write
Reading and writing to and from flash storage is slowed down
enormously by some functions which use a block size of 1.

This patch reworks the extraction scripts to be much faster and
efficient by reading and writing in possibly one big block.

This is based on the initial commit a69e101 for ipq40xx by
Christian Lamparter <chunkeey@gmail.com>.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Rosen Penev <rosenp@gmail.com>
2019-03-21 00:57:54 +01:00
Ozgur Can Leonard 201d3d1a82 ramips: Xiaomi MIR3G: detect board name from DTS
- Former "mir3g" board name becomes "xiaomi,mir3g".
- Reorder some entries to maintain alphabetical order.
- Change DTS so status LEDs (yellow/red/blue) mimic
  Xiaomi stock firmware: (Section Indicator)
<http://files.xiaomi-mi.co.uk/files/router_pro/router%20PRO%20EN.pdf>
<http://files.xiaomi-mi.co.uk/files/Mi_WiFi_router_3/MiWiFi_router3_EN.pdf>
|Yellow: Update (LED flickering), the launch of the system (steady light);
|Blue: during normal operation (steady light);
|Red: Safe mode (display flicker), system failure (steady light);

Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
[Added link to similar Router 3 model]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-21 00:57:54 +01:00
INAGAKI Hiroshi 5c11258297 ramips: add support for I-O DATA WN-AC733GR3
I-O DATA WN-AC733GR3 is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7620A.

Specification

- SoC		: MediaTek MT7620A
- RAM		: DDR2 64 MiB
- Flash		: SPI-NOR 8 MiB
- WLAN		: 2.4/5 GHz
  - 2.4 GHz : MT7620A (SoC), 2T2R
  - 5 GHz   : MT7610E, 1T1R
- Ethernet	: 10/100/1000 Mbps (RTL8367RB)
- LED/key	: 4x/4x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J1: Vcc, RX, GND, TX from LED side
  - 57600n8

Flash instruction using factory image:

1. Boot WN-AC733GR3 normaly
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-03-21 00:57:20 +01:00
Micke Prag c3a17ee4b3 ramips: add #pwm-cells property to MT76x8 dts
To be able to configure pwms the pwm driver needs to know the number off
cells in the "pwms" property. For this platform this is 2.

Signed-off-by: Micke Prag <micke.prag@telldus.se>
2019-03-18 20:43:09 +01:00
Koen Vandeputte a8cfef6c45 kernel: bump 4.14 to 4.14.106
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-18 10:02:51 +01:00
Chen Minqiang 7dfe357a3d ramips: HC5861 drop unused gpio group define in dts
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2019-03-13 16:25:34 +01:00
Ozgur Can Leonard d009033911 ramips: add support for Xiaomi Mi Router 3 Pro
Hardware:

CPU:   MediaTek MT7621AT (2x880MHz)
RAM:   512MB DDR3
FLASH: 256MB NAND
WiFi:  2.4GHz 4x4 MT7615 b/g/n (Needs driver, See Issues!)
WiFI:  5GHz 4x4 MT7615 a/n/ac  (Needs driver, See Issues!)
USB:   1x 3.0
ETH:   1x WAN 10/100/1000 3x LAN 10/100/1000
LED:   Power/Status
BTN:   RESET
UART:  115200 8n1

Partition layout and boot:

Stock Xiaomi firmware has the MTD split into (among others)

- kernel0 (@0x200000)
- kernel1 (@0x600000)
- rootfs0
- rootfs1
- overlay (ubi)

Xiaomi uboot expects to find kernels at 0x200000 & 0x600000
referred to as system 1 & system 2 respectively.
a kernel is considered suitable for handing control over
if its linux magic number exists & uImage CRC are correct.
If either of those conditions fail, a matching sys'n'_fail flag
is set in uboot env & a restart performed in the hope that the
alternate kernel is okay.
If neither kernel checksums ok and both are marked failed, system 2
is booted anyway.

Note uboot's tftp flash install writes the transferred
image to both kernel partitions.

Installation:

Similar to the Xiaomi MIR3G, we keep stock Xiaomi firmware in
kernel0 for ease of recovery, and install OpenWRT into kernel1 and
after.

The installation file for OpenWRT is a *squashfs-factory.bin file that
contains the kernel and a ubi partition. This is flashed as follows:

nvram set flag_try_sys1_failed=1
nvram set flag_try_sys2_failed=0
nvram commit
dd if=factory.bin bs=1M count=4 | mtd write - kernel1
dd if=factory.bin bs=1M skip=4 | mtd write - rootfs0
reboot

Reverting to stock:

The part of stock firmware we've kept in kernel0 allows us to run stock
recovery, which will re-flash stock firmware from a *.bin file on a USB.

For this we do the following:

fw_setenv flag_try_sys1_failed 0
fw_setenv flag_try_sys2_failed 1
reboot

After reboot the LED status light will blink red, at which point pressing
the 'reset' button will cause stock firmware to be installed from USB.

Issues:

OpenWRT currently does not have support for the MT7615 wifi chips. There is
ongoing work to add mt7615 support to the open source mt76 driver. Until that
support is in place, there are closed-source kernel modules that can be used.

See: https://forum.openwrt.org/t/support-for-xiaomi-wifi-r3p-pro/20290/170

Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[02_network remaps, Added link to notes]
2019-03-13 16:25:34 +01:00
Piotr Dymacz 9b6413982c ramips: add support for ALFA Network Tube-E4G
ALFA Network Tube-E4G is an outdoor, dual-SIM LTE Cat. 4 CPE, based on
MediaTek MT7620A, equipped with Quectel EC25 miniPCIe modem.

Specification:

- MT7620A (580 MHz)
- 64/128/256 MB of RAM (DDR2)
- 16/32 MB of flash (SPI NOR)
- 1x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 2x SIM slot (mini, micro) with detect and switch driven by GPIO
- 1x detachable antenna (modem main)
- 1x internal antenna (modem div)
- 1x GPS passive antenna (optional)
- 5x LED (all driven by GPIO)
- 1x button (reset)
- UART (4-pin, 2.54 mm pitch) header on PCB

Other:

Default SIM slot is selected at an early stage by U-Boot, based on
'default_sim' environment value: 1 or unset = SIM1 (mini), 2 = SIM2
(micro). U-Boot also resets the modem, using #PERST signal, before
starting kernel.

Flash instruction:

You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:

1. Power the device with reset button pressed, the LAN LED will start
   blinking slowly and after ~3 seconds, when it starts blinking faster,
   you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-03-11 22:00:26 +01:00
Chen Minqiang e15bda603a ramips: rework network settings for HC5861
dts: disable port4 and leave it ephy mode because it connect to nothing
switch port5 connected to GE port we use it as wan port

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2019-03-06 22:02:56 +01:00
Daniel Golle c8778250a9 ramips: mt7620: export chip version and pkg
Similar to the (currently unused) mt7620_get_eco() function, introduce
mt7620_get_chipver() and mt7620_get_pkg() functions to allow rt2x00 to
probe for the type of WiSoC. This is ugly and probably unacceptable
for upstream, however, it should help to evaluate which of those hacks
are actually really needed, enumerate the possible values and label
them in a more meaningful way than currently done in the vendor driver.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-06 01:11:54 +01:00
Kip Porterfield f2c83532f9 ramips: add support for Belkin F9K1109v1
Device specification:
- SoC: Ralink RT3883 (MIPS 74Kc) 500Mhz
- RAM: 64Mb
- Flash: 8MB (SPI-NOR)
- Ethernet: 10/100/1000 Mbps
- WLAN
	Wireless 1: SoC-integrated : 2.4/5 GHz
	Wireless 2: 2.4 GHz RT3092L
- LED: 2x USB, WAN, LAN
- Key: WPS, reset
- Serial: 4-pin header, (57600,8,N,1), 3.3V TTL,
	GND, RX, TX, V - J12 marking on board
- USB ports: 2 x USB 2.0

Flashing instructions:

Option 1 (from bootloader web)
- Hold reset button on the back of router when plugging
  in power (for at-least 10 seconds after plugged in)
- Connect to a Lan port
- Set computer IP to 10.10.10.3
- Go to http://10.10.10.123 in a web browser
- Click the Browse... Button and select the
   *squashfs.sysupgrade.bin file then click APPLY

Option 2 (from the stock admin web)
- Go to firmware upgrade
- Upload the **factory** image *initramfs.bin first
- Boot into openwrt
- From Luci web in openwrt upload the *squashfs.sysupgrade.bin

Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added v1 to the compatible identifier, added pciid for
the RT3092L, fixed pci unit-address, split out the F9K110X.dtsi
to prepare for a possible F9K1103 patch]
2019-03-02 13:04:45 +01:00
Marcel Jost e6f047fa36 ramips: add TP-Link TL-WR802N-v4 support
This patch adds support for the TP-Link TL-WR802N-v4.
https://openwrt.org/toh/tp-link/tl-wr802n

Specification:
- MT7628N (580 MHz)
- 64 MB RAM
- 8 MB FLASH
- 2T2R 2.4 GHz
- 1x 10/100 Mbps Ethernet
- 1x LED

Flash instruction:

The only way to flash the image in TL-WR802N v4 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr802n-v4-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
   the router and keep button pressed for around 10 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Marcel Jost <majo@icutech.ch>
2019-02-28 11:26:10 +01:00
Thomas Vincent-Cross a915ad8464 ramips: use generic board detection for Wavlink WL-WN575A3
Bring Wavlink WL-WN575A3 in line with other Wavlink ramips devices.

Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
2019-02-28 11:26:10 +01:00
Thomas Vincent-Cross 25c0b41901 ramips: various Wavlink WL-WN575A3 fixes
* assign pinmux groups to gpio function for LEDs/buttons
* rename flash node to be more generic in line with other device nodes
* remove useless/incorrect eeprom property from wmac node
* correct base mac address for embedded switch

Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
2019-02-28 11:26:10 +01:00
INAGAKI Hiroshi e52ad0f919 ramips: change status LED for Buffalo WHR-G300N
Buffalo WHR-G300N has a LED for power status indication, but it is not
connected to the GPIO and cannot be controlled by the kernel. So,
WHR-G300N uses "ROUTER" LED as the system status LED instead.

This commit changes it to use "DIAG" LED insted of "ROUTER" like
WHR-G301N in ath79 target.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-02-14 16:56:15 +01:00
David Bauer 7bf6b59724 ramips: various Netgear R6120 fixes
The R6120 has no 5GHz WLAN LED, the assigned GPIO in fact controls
the WAN LED.

Renames the LED accordingly in the device-tree.
Removes the 5GHz WLAN LED trigger.
Adds the correct WAN port LED trigger.

----

Currently, the MAC address for the Netgear R6120 is read from the NVRAM
partition. The offset for the MAC address however is not consistent
across devices or firmware versions.

Switch to using the factory partition like all other Netgear devices do.

----

The LAN ports of the R6120 are labled in reverse on the casing.

Adjust LuCI switchport numbering accordingly.

----

The WiFi eeprom offsets for the R6120 are currently wrong (5GHz offset
is bigger than the partition itself).

Fixes poor performance on 2.4 and 5 GHz.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-02-14 16:56:14 +01:00
INAGAKI Hiroshi f305ce5c35 ramips: add support for I-O DATA WN-AC1167GR
I-O DATA WN-AC1167GR is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7620A.

Specification:

- SoC     : MediaTek MT7620A
- RAM     : DDR2 64 MB
- Flash   : SPI-NOR 8MB
- WLAN    : 2.4/5 GHz, 2T2R
  - 2.4 GHz: MT7620A (SoC)
  - 5 GHz  : MT7612E
- Ethernet: 10/100/1000 Mbps (ext. MT7530)
- LED/key : 4x/3x (2x buttons, 1x slide-switch)
- UART    : through-hole on PCB
  - J2: TX, GND, RX, Vcc from SoC side
  - 115200n8

Flash instruction using factory image:

1. Boot WN-AC1167GR normaly
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-02-14 16:56:14 +01:00
Koen Vandeputte 9a1d7ff187 kernel: bump 4.14 to 4.14.99
Refreshed all patches.

Remove upstreamed:
- 950-0434-mmc-bcm2835-Recover-from-MMC_SEND_EXT_CSD.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-14 16:45:01 +01:00
Chuanhong Guo be2b61e4f1 ramips: drop m25p,chunked-io from dts
This option was a spi nor hack which is dropped in commit
bcf4a5f474 ("ramips: remove chunked-io patch and set spi->max_transfer_size instead")

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [edit message]
2019-02-05 19:37:30 +01:00
Deng Qingfang 6621da55b7 ramips: enable MT7610E 5GHz radio of MT7620a_MT7610e EVB
This enables MT7610E of the EVB

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2019-02-05 19:37:30 +01:00
Ju Se Hoon 9f90074db7 ramips: add kmod-mt76x2 to WeVo 11AC NAS
The WeVo 11AC NAS has a MT7612E 802.11ac chip on the PCB.

Signed-off-by: Ju Se Hoon <joosahoon@gmail.com>
[renamed author from Albis-dev to real name, editted commit message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-05 19:37:30 +01:00
Petr Štetiar dd3ec40d3d ramips: dts: Unify naming of gpio-led nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2019-02-05 16:28:12 +01:00
Petr Štetiar e8eaf794ec ramips: dts: Unify naming of gpio-keys nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2019-02-05 16:28:12 +01:00
Koen Vandeputte 206bebcad4 kernel: bump 4.14 to 4.14.97
Refreshed all patches.

Adapted patches:
- 012-kbuild-add-macro-for-controlling-warnings-to-linux-c.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-01 11:41:00 +01:00
Anton Arapov ae0a40d68d ramips: rb750gr3: License DTS as GPL-2.0-or-later OR MIT
Adding license in order to fully satisfy dts checklist:
- https://openwrt.org/submitting-patches#dts_checklist

Signed-off-by: Anton Arapov <arapov@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Thibaut <hacks@slashdirt.org>
Acked-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Acked-by: Chuanhong Guo <gch981213@gmail.com>
Acked-by: Andrew Yong <me@ndoo.sg>
Acked-by: Alex Maclean <monkeh@monkeh.net>
2019-02-01 06:35:13 +01:00
Mirko Parthey 555ca422d1 ramips: fix D-Link DIR-615 H1 switch port mapping
Reuse a device-specific switch port mapping which also applies to the
D-Link DIR-615 H1.

Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
2019-01-30 13:31:43 +01:00
Felix Fietkau 01895c315f ramips: move wifi related interrupts off the main core on SMP systems
Improves LAN<->WLAN bridging/routing performance

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-01-29 11:27:02 +01:00
Koen Vandeputte 3662157d8b kernel: bump 4.14 to 4.14.96
Refreshed all patches.

Remove upstreamed patches:
- 142-jffs2-Fix-use-of-uninitialized-delayed_work-lockdep-.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-28 18:17:32 +01:00
Hauke Mehrtens fcbbec8eb2 kernel: Fix kmod-regmap split
Two regmap dependencies were wrong, this patch fixes them.
This was detected by the build bots.

Fixes: fd5c168701 ("kernel: Build: Split kmod-regmap")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-27 11:07:14 +01:00
Hauke Mehrtens fd5c168701 kernel: Build: Split kmod-regmap
This reduces the needed modifications to the mainline Linux kernel and
also makes the regmap package work with an out of tree kernel which
does not have these modifications.

The regmap-core is only added when it is really build as a module.
The regmap-core is normally bool so it cannot be built as a module in an
unmodified kernel. When it is selected by on other kernel module it will
always be selected as build in and it also does not show up in
$(LINUX_DIR)/modules.builtin as it is not supposed to be a kernel module.
When it is not in $(LINUX_DIR)/modules.builtin the build system expects
it to be built as a .ko file.
Just check if the module is really there and only add it in that case.

This splits the regmap package into multiple packages, one for each bus type.
This way only the bus maps which are really needed have to be added.
This also splits the I2C, SPI and MMIO regmap into separate packages to not
require all these subsystems to build them, on an unmodified upstream kernel
this also causes problems in some situations.

Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
2019-01-27 00:16:13 +01:00
Mathias Kresin 2a4e756085 ramips: rt3883: drop jimage support
The splitter isn't required by any of the boards in the subtarget.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-26 21:46:33 +01:00
Mathias Kresin 8293aec943 ramips: disable CONFIG_MTD_SPLIT_FIRMWARE
It's no longer needed as all mt7621 devices use DT binding (supported by
upstream mtd code) for specifying "firmware" part format explicitly.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-26 21:46:33 +01:00
Rafał Miłecki acd790c150 ramips: specify "firmware" partition format for remaining devices
It results in calling the right MTD parser directly instead of trying
them one by one.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
[use the lzma splitter for the AR670W]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-26 21:46:33 +01:00
David Bauer 01dcd574a2 ramips: add support for Archer C50 v4
This adds support for the TP-Link Archer C50 v4.
It uses the same hardware as the v3 variant, sharing the same FCC-ID.

CPU:   MediaTek MT7628 (580MHz)
RAM:   64M DDR2
FLASH: 8M SPI
WiFi:  2.4GHz 2x2 MT7628 b/g/n integrated
WiFI:  5GHz 2x2 MT7612 a/n/ac
ETH:   1x WAN 4x LAN
LED:   Power, WiFi2, WiFi5, LAN, WAN, WPS
BTN:   WPS/WiFi, RESET
UART:  Near ETH ports, 115200 8n1, TP-Link pinout

Create Factory image
--------------------
As all installation methods require a U-Boot to be integrated into the
Image (and we do not ship one with the image) we are not able to create
an image in the OpenWRT build-process.

Download a TP-Link image from their Wesite and a OpenWRT sysupgrade
image for the device and build yourself a factory image like following:

TP-Link image:             tpl.bin
OpenWRT sysupgrade image:  owrt.bin

 > dd if=tpl.bin of=boot.bin bs=131584 count=1
 > cat owrt.bin >> boot.bin

Installing via Web-UI
---------------------
Upload the boot.bin via TP-Links firmware upgrade tool in the
web-interface.

Installing via Recovery
-----------------------
Activate Web-Recovery by beginning the upgrade Process with a
Firmware-Image from TP-Link. After starting the Firmware Upgrade,
wait ~3 seconds (When update status is switching to 0%), then
disconnect the power supply from the device. Upgrade flag (which
activates Web-Recovery) is written before the OS-image is touched and
removed after write is succesfull, so this procedure should be safe.

Plug the power back in. It will come up in Recovery-Mode on 192.168.0.1.
When active, all LEDs but the WPS LED are off.
Remeber to assign yourself a static IP-address as DHCP is not active in
this mode.

The boot.bin can now be uploaded and flashed using the web-recovery.

Installing via TFTP
-------------------
Prepare an image like following (Filenames from factory image steps
apply here)

 > dd if=/dev/zero of=tp_recovery.bin bs=196608 count=1
 > dd if=tpl.bin of=tmp.bin bs=131584 count=1
 > dd if=tmp.bin of=boot.bin bs=512 skip=1
 > cat boot.bin >> tp_recovery.bin
 > cat owrt.bin >> tp_recovery.bin

Place tp_recovery.bin in root directory of TFTP server and listen on
192.168.0.66/24.

Connect router LAN ports with your computer and power up the router
while pressing the reset button. The router will download the image via
tftp and after ~1 Minute reboot into OpenWRT.

U-Boot CLI
----------
U-Boot CLI can be activated by holding down '4' on bootup.

Dual U-Boot
-----------
This is the first TP-Link MediaTek device to feature a split-uboot
design. The first (factory-uboot) provides recovery via TFTP and HTTP,
jumping straight into the second (firmware-uboot) if no recovery needs
to be performed. The firmware-uboot unpacks and executed the kernel.

Web-Recovery
------------
TP-Link integrated a new Web-Recovery like the one on the Archer C7v4 /
TL-WR1043v5. Stock-firmware sets a flag in the "romfile" partition
before beginning to write and removes it afterwards. If the router boots
with this flag set, bootloader will automatically start Web-recovery and
listens on 192.168.0.1. This way, the vendor-firmware or an OpenWRT
factory image can be written.

By doing the same while performing sysupgrade, we can take advantage of
the Web-recovery in OpenWRT.

It is important to note that Web-Recovery is only based on this flag. It
can't detect e.g. a crashing kernel or other means. Once activated it
won't boot the OS before a recovery action (either via TFTP or HTTP) is
performed. This recovery-mode is indicated by an illuminated WPS-LED on
boot.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-26 21:46:32 +01:00
Deng Qingfang c2bcdabf2a ramips: fix support for MX25L25635F flash
Patch picked from commit 82618062cf

This enables 4B opcodes for MX25L25635F, to fix the reboot crash
issue (FS#1120) At least 3 devices are using this flash
- GeHua GHL-R-001
- Youku YK1
- Newifi D1

Now the MX25L25635F can be correctly detected without breaking MX25L25635E
[ 3.034324] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[ 3.045962] m25p80 spi0.0: mx25l25635f (32768 Kbytes)
[ 3.056098] 4 fixed-partitions partitions found on MTD device spi0.0
[ 3.068748] Creating 4 MTD partitions on "spi0.0":

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added deprecation notice]
2019-01-26 17:10:19 +01:00
David Bauer 915fbd4e31 ramips: adjust Netgear R6120 model name
Adjust the model string and device title to match other Netgear routers
in the ramips target.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-26 10:41:03 +01:00
HsiuWen Yen fe7d965ea9 ramips: fix two-way hash and auto ageout on MT7621
Current code directly writes the FOE entry to hash_val+1 position
when hash collision occurs. However, it is found that this behavior
will cause the cache and the hardware FOE table to be inconsistent.

For example, there are three flows, and their hashed values are all
equal to 100. The first flow is written to the position of 100. The
second flow is written to the position of 100+1. Then, the logic of
the current code will also write the third flow to 100+1.

At this time, the cache has flow 1 and 2; and the hardware FOE table
has flow 1 and 3, where these two parts store different contents.
So it is necessary to check whether the hash_val+1 is also occupied
before writing. If hash_val+1 is also occupied, we won’t bind th
third flow to the FOE table.

Addition to that, we also cancel the processing of foe_entry removal
because the hardware has auto age-out ability. The hardware will
periodically iterate through the FOE table to find out the time-out
entry and set it as INVALID.

Signed-off-by: HsiuWen Yen <y.hsiuwen@gmail.com>
2019-01-23 09:27:30 +01:00
Mathias Kresin f5e61350e7 ramips: fix firmware splitter for edimax based boards
Use the correct splitter for board with the edimax header.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-19 12:51:04 +01:00
Mathias Kresin 26a016731d firmware-utils: mksercommfw: overhaul image creation
Move the zip compression into a build recipe. Pad the image using the
existing build recipes as well to remove duplicate functionality

Change the code to append header and footer in two steps. Allow to use a
fixed filename as the netgear update image does.

Use a fixed timestamp within the zip archive to make the images
reproducible.

Due to the changes we are now compatible to the gnu89 c standard used by
default on the buildbots and we don't need to force a more recent
standard anymore.

Beside all changes, the footer still looks wrong in compare to the
netgear update image.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-15 19:11:54 +01:00
Koen Vandeputte f56a4e809b kernel: bump 4.14 to 4.14.91
Refreshed all patches.

Removed upstreamed:
- 500-ubifs-Handle-re-linking-of-inodes-correctly-while-re.patch

Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-07 17:09:06 +01:00
John Crispin 93c35bfa21 ramips: whitespace cleanup inside hnat driver
Signed-off-by: John Crispin <john@phrozen.org>
2019-01-07 15:45:51 +01:00
HsiuWen Yen 6b9bdbd493 ramips: add two-way hashing scheme for MT7621
Sometimes the tuples might be hashed to the same FOE entry.
When this hash collision problem occurs, some of the
connections will not be bound and consequently the CPU
idle rate cannot reach 100%. Therefore, two-way hashing
is adopted to alleviate this problem.

Signed-off-by: HsiuWen Yen <y.hsiuwen@gmail.com>
2019-01-07 15:40:51 +01:00
Anton Arapov 6ba58b7b02 ramips: cleanup the RB750Gr3 support
Always enable the pwr led and use the usr led for boot status indication.

Rename nodes in the dts, to match what is recommend in the devicetree
specification.

Increase the maximum spi frequency to 20MHz and drop the m25p,chunked-io
which isn't required on mt7621.

Use the BTN_0 keycode for the mode button. This board doesn't have any
wireless.

Use a more descriptive label for the reset button and the GPIO enabling
the usb vcc supply.

Use the beeper kernel module for the buzzer.

Fix the pinmux to switch only pins used as GPIOs to the GPIO function.
Add support for the PoE enable GPIO to the userspace. The PoE power
status can be read via GPIO7. Since OpenWrt doesn't have support for
reading inputs from userspace, prepare only the pinmux for the GPIO.

Signed-off-by: Anton Arapov <arapov@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-05 12:28:22 +01:00
Anton Arapov 52f2d7d2a9 ramips: add RB750Gr3 native support
This patch adds support of MikroTik RouterBOARD 750Gr3, without the need
to reflashing the bootloader.

Installation through RouterBoot follows the usual MikroTik method
https://openwrt.org/toh/mikrotik/common

Since the image isn't compatible with RouterBOARD 750Gr3 installations
which have replaced the bootloader, the former used userspace boardname
is not added to the SUPPORTED_DEVICES, to prevent a brick while trying
to upgrade to the image with native support.

Signed-off-by: Anton Arapov <arapov@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-05 12:28:22 +01:00
Paul Wassi 28a5674e33 treewide: fix spaces vs. tabs
Fix spaces vs. tabs issues in ath79 and ramips.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-12-31 16:37:20 +01:00
Mathias Kresin fd35c5b205 build: move seama commands to image-commands.mk
Move it to image-commands.mk to get rid of duplicate recipes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-30 20:08:13 +01:00
Mathias Kresin 7c1332d95f ramips: consolidate seama image build code
Create a common template which has the required image build code
defined. Add some new variables to pass individual parts to the seama
recipes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-30 20:08:12 +01:00
Deng Qingfang 5580a9dd31 ramips: add support for GeHua GHL-R-001
Specs
	SoC: MT7621AT
	RAM: 512MiB
	Flash: 32MiB MX25L25635F SPI NOR
	2.4G: MT7603EN
	5G: MT7612EN
	Ethernet: 4x GE ports (1x WAN, 3x LAN) with link status LEDs
	USB 3.0
	LEDs: POWER, 5G WIFI, 2.4G WIFI, USB, Internet.
	      The last two ones are controlled by GPIO
	UART: There are 2 UARTs (UARTLITE1/ttyS0 and UARTLITE3/ttyS1) on board.
	      UARTLITE1 is close to LEDs, and UARTLITE3 is close to flash chip.
	      The stock u-boot uses UARTLITE1 by default. Baud rate is 57600

Flash instruction
	1. telnet 192.168.9.1 2317, username is "root" and password is "admin"
	   One can alternatively use UART to log in
	2. Put OpenWrt firmware in a FAT32 USB drive, and connect it to the router
	   One can alternatively download the firmware via wget through Internet
	3. mtd write /path/to/openwrt.bin firmware
	4. reboot

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2018-12-29 16:03:30 +01:00
Deng Qingfang 0599cd90e1 ramips: fix MT7621 dtsi
Fix SysTick reg
Add uartlite2 and uartlite3 nodes

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2018-12-29 16:03:30 +01:00
Simon Quigley 9f0e233576 ramips: add support for DLINK DWR-922-E2
Very similar to the DWR-921-C1, except has a telephony/RJ11 port (not
sure if supported, I didn't try), wireless router with QMI LTE embedded
modem is based on the MT7620N SoC.

Specification:

  * MediaTek MT7620N (580 Mhz)
  * 64 MB of RAM
  * 16 MB of FLASH
  * 802.11bgn radio
  * 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
  * 2x external, detachable (LTE) antennas
  * UART header on PCB (57600 8n1)
  * 6x LED (GPIO-controlled)
  * 1x bi-color Signal Strength LED (GPIO-controlled)
  * 2x button
  * JBOOT bootloader

The status led has been assigned to the dwr-922-e2:green:signalstrength
(lte signal strength) led. At the end of the boot it is switched off and
is available for lte operation. Works correctly also during sysupgrade
operation.

Installation:
Apply factory image via d-link http web-gui, or via recovery interface:

How to recover/revert to OEM firmware:
1.) Push and hold the reset button and turn on the power. Wait until all
    LEDs start rapidly blinking (~10sec.)
2.) DHCP should give you an IP in the 192.168.123.0/24 subnet, or set
    one manually
3.) Upload original factory image via JBOOT http interface at IP
    192.168.123.254
4.) If http doesn't work, it can be done with curl command:
      curl -F FN=@XXXXX.bin http://192.168.123.254/upg
    where XXXXX.bin is name of firmware file.
5.) You can optionally telnet to 192.168.123.254 before or during the
    upload and it will report the flashing status, memory address etc.
6.) Once web UI and/or telnet says "Success", power cycle the router, or
    type "reboot" into the telnet session.

Signed-off-by: Simon Quigley <squigley@squigley.net>
[squashed commits, word wrap commit message, rename signal strenght led
name to match what is used for the DWR-921-C1 since they share the led
configuration, add label referenced in the aliases node]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-29 16:03:30 +01:00
Andreas Ziegler d492da702a ramips: mt7621: fix 5GHz WiFi LED on ZBT WG3526
This fixes the 5GHz WiFi LED which was previously not working.

Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
2018-12-29 12:35:47 +01:00
Weijie Gao 74af8a833a ramips: add support for CreativeBox v1
Hardware:
SoC: MT7621
DRAM: 512MB DDR3
Flash: 32MB SPI-NOR
WiFi 2.4GHz: MT7603 @ PCIe0
WiFi 5.8GHz: MT7612 @ PCIe1
SATA: ASM1061 @ PCIe2

Interfaces:
GBE RJ45 x5
USB3.0 x1
eSATA (with USB2.0) x1
SATA x1
UART x1
I2C x1
JTAG x1

Flash instructions:
Through factory bootloader or firmware web interface

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-12-28 12:45:23 +01:00
NOGUCHI Hiroshi d020ae79ab ramips: add SPDX license identifier into some dts,dtsi
Acked-by: Mathias Kresin <dev@kresin.me>
Acked-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
2018-12-28 12:45:23 +01:00
Petr Štetiar 0d23fd2ab2 treewide: dts: Remove default-state=off property from all gpio LED nodes
>From the Documentation/devicetree/bindings/leds/common.txt:

- default-state : The initial state of the LED. Valid values are "on", "off",
  and "keep". If the LED is already on or off and the default-state property is
  set the to same value, then no glitch should be produced where the LED
  momentarily turns off (or on). The "keep" setting will keep the LED at
  whatever its current state is, without producing a glitch.  The default is
  off if this property is not present.

So setting the default-state of the LEDs to `off` is redundant as `off`
is default LED state anyway. We should remove it as almost every new
PR/patch submission contains this property by default which seems to be
just copy&paste from some DTS file already present in the tree.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-17 08:16:28 +01:00
NOGUCHI Hiroshi 83a97c53fa ramips: add support for Netgear R6350
Netgear R6350 is a wireless router, aka Netgear AC1750.

Specification:
- SoC: Mediatek MT7621AT (2 CPU cores, 4 threads)
- RAM: 128MiB (Nanya NT5CC64M16GP-DI)
- ROM: 128MiB NAND Flash (Macronix MX30LF1G18AC-TI)
- Wireless:
   for 11b/g/n (upto 300Mbps): MT7603
   for 11a/ac  (upto 1450Mbps) : MT7615, is not avaliable now
- Ethernet LAN speed: up to 1000Mbps
- Ethernet LAN ports: 4
- Ethernet WAN speed: up to 1000Mbps
- Ethernet WAN ports: 1
- USB ports: 1 (USB 2.0)
- LEDs: 4 (all can be controlled by SoC's GPIO)
- buttons: 2
- serial ports: unknown

Installation through telnet:
  - Copy kernel.bin and rootfs.bin to a USB flash disk,
    plug to usb port on the router.
  - Enable telnet with link: http://192.168.1.1/setup.cgi?todo=debug
    (login if required, default: admin password)
  - You will see "Debug Enabled!"
  - Telnet 192.168.1.1 and login with "root"
  - ls /mnt/shares/ to find out path of your USB disk.
    'myUdisk' for example.
  - cd /mnt/shares/myUdisk
  - mtd_write write rootfs.bin Rootfs
  - mtd_write write kernel.bin Kernel
  - reboot

recovery when bricked:
  nmrpflash can be used to recover to the netgear firmware
  if a broken image was flashed.

The SC_PART_MAP partition suggests that an on flash partition table
exists. After implementing a partition parser/builder for the sercom
partition format, the definitions don't match the flash layout used by
the stock firmware.

It either means the partition format has not yet been completely
understood or it isn't used by the stock firmware. For now, use fixed
partitions instead.

Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
[apply latest ramips changes and document the on flash partition map
issues]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-16 08:41:41 +01:00
Mathias Kresin dd5e7d6c50 ramips: mt7620: add usb packages
Add the usb drivers for all boards with enabled ochi/ehci node in the
dts file.

Fixes: FS#1987

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-15 20:02:07 +01:00
Mathias Kresin 30c07a5675 ramips: mt7620: remove unnecessary usb packages
These are either installed as dependency or not required at all.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-15 20:02:07 +01:00
Mathias Kresin e04d352d63 ramips: mt7620: add usb ohci driver
Add the USB 1.1 driver for all boards not having a fixed USB 2.0
device attached to the USB bus.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-15 20:02:07 +01:00
Deng Qingfang 47381aadd5 ramips: several fixes for HC5x61
- Mark other partitions as read-only for HC5x61

 - Only enable USB and PCIe for HC5761/HC5861
   HC5661 doesn't have a USB port, and there is nothing attached to its PCIe.

 - Fix HC5761 switch ports
   HC5761 has only 3 ethernet ports (1x WAN + 2x LAN). Remove unused ports.

 - Fix HC5861 5GHz radio
   HC5861 has MT7612EN 5GHz WiFi chip, not MT7610EN.

 - Fix HC5761/HC5861 WiFi LEDs
   After 5GHz is enabled, it becomes wlan0. And 2.4GHz would be wlan1.

 - Fix HC5x61 image size
   It should be 15872k (0xf80000)

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2018-12-15 20:02:07 +01:00
Rafał Miłecki 840c4cba92 ramips: mt7621: disable CONFIG_MTD_SPLIT_FIRMWARE
It's no longer needed as all mt7621 devices use DT binding (supported by
upstream mtd code) for specifying "firmware" part format explicitly.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-13 13:39:56 +01:00
Rafał Miłecki c56241c052 ramips: mt7621: specify "firmware" partition format for remaining devices
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-13 13:39:56 +01:00
Mathias Kresin 35f70774b8 ramips: drop old image validation code
Due to the enforced image metadata we ensure that the correct image is
uploaded. Checks based on a magic arn't required any more.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-12 11:01:59 +01:00
Mathias Kresin 1a5df6add7 ramips: enforce image metadata verification
Now that we got rid of all legacy images, we can enforce image metadata
verification.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-12 11:01:59 +01:00
Mathias Kresin 8e40fbff0b ramips: drop support for ALLNET ALL0239-3G and Sitecom WL-341 v3
Beside one exception, no one took care of these two remaining boards
still using the legacy image build code during the last two years.

Since OpenWrt 14.07 the ALLNET ALL0239-3G image building is broken.

The Sitecom WL-341 v3 image build code looks pretty hackish and broken.
It's questionable if the legacy image works as all.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-12 11:01:59 +01:00
Mathias Kresin 262b885b83 ramips: use new image build code for D-Link DCS-930 family
Drop the factory images and the firmware tool to create them. They don't
work any more, since the factory image has an uImage header covering the
whole kernel + rootfs. This way the uImage splitter will not be able to
find the rootfs and the kernel will panic later on.

The factory images were most likely added at a time the board had
distinct partitions for kernel and rootfs.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-12 11:01:59 +01:00
Koen Vandeputte f6e9f23771 kernel: bump 4.14 to 4.14.87
Refreshed all patches.

Remove upstreamed:
- 0008-MIPS-ralink-Fix-mt7620-nd_sd-pinmux.patch

Compile-tested: cns3xxx, imx6
Runtime-tested: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-12-10 16:32:22 +01:00
Koen Vandeputte 0028f86687 kernel: bump 4.14 to 4.14.86
Refreshed all patches.

Altered patches:
- 180-usb-xhci-add-support-for-performing-fake-doorbell.patch

Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-12-10 11:48:44 +01:00
Russell Senior ed000fcaf2 ramips: fix firmware compatible string for dir860l-b1
In commit d70ec3008d, a firmware compatible
string of "denx,uimage" was added for the Dlink DIR-860L-B1. Unfortunately,
this was the wrong string. It needs "seama" instead.

Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-12-08 14:18:42 +01:00
Mathias Kresin ffa55386f1 ramips: fix dtc compiler warnings
The latest dtc compiler considers nodes named i2c or spi as the
respective bus:

  /pinctrl/i2c: incorrect #address-cells for I2C bus
  /pinctrl/spi: incorrect #address-cells for SPI bus

Rename the node to fix the false positives.

Fix the spi node unit address for the DWR-512-B and UBNT-ER-e50 to get
rid of the following warning:

  SPI bus unit address format error, expected "n"

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 12:17:25 +01:00
Chen Minqiang 295b37d207 ramips: mt76x8: select only the matching mt76 driver
Select the matching mt76 driver for the PCI wireless of the following
devices:

 - HiWiFi HC5861B
 - Mercury MAC1200R v2.0
 - Netgear AC1200 R6120
 - Buffalo WCR-1166DS
 - ZyXEL Keenetic Extra II
 - Wavlink WL-WN575A3

Because every device has selected the corresponding mt76 driver, we can
include kmod-mt7603 instead of the mt76 metapackage, which used for the
wireless of the mt7628 and mt7688 WiSoC.

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
[select kmod-mt7603 as target default package, add wireless driver for
WL-WN575A3]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 12:17:25 +01:00
Chuanhong Guo 5563d49a39 ramips: disable sdhc for HC5661A
Currently OpenWrt doesn't support switching MT7628 into AP mode
(which is done by writing some undocumented registers in MTK SDK)
Without doing so, enabling SD breaks 4 FE ports and the SD controller
doesn't work since SD pins aren't configured correctly.

Disable SDHC on HC5661A to recover the 4 FE ports.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[drop the sdhci node completely]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 12:17:25 +01:00
Petr Štetiar 9da6cd40eb apm821xx, ath79, ipq40xx, ipq806x, lantiq, ramips: base-files: Use generic diag.sh
I wanted to add status LEDs support to my imx6 based board and have found out,
that I could use diag.sh script found in ramips platform, which seems to be
also shared in a few other platforms:

 4801276bc2078c5bcf03003c831e3b0a target/linux/ramips/base-files/etc/diag.sh
 4801276bc2078c5bcf03003c831e3b0a target/linux/ipq40xx/base-files/etc/diag.sh
 4801276bc2078c5bcf03003c831e3b0a target/linux/ath79/base-files/etc/diag.sh

And @chunkeey suggested to me, that I can also add lantiq, ipq806x and
apm821xx to the list of platforms which could share this generic
diag.sh.

I've extended the base diag.sh in a way, that if it detects any of the
DTS LED aliases, then it would use the generic DTS set_led_state code.
The code in platform's diag.sh has moved to base-files package in this
commit:

 base-files: diag.sh: Make it more generic towards DTS so it could be reused

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Tested-by: Christian Lamparter <chunkeey@gmail.com> (apm821xx and ipq40xx)
2018-12-06 08:42:40 +01:00
Mathias Kresin f381cbcb5f ramips: fix Netgear EX3700/EX3800 wireless driver selection
Fix the typo to select kmod-mt76x2.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-04 20:40:27 +01:00
Pawel Dembicki e9a9b7d1ed ramips: add support for D-Link DWR-118-A1
The DWR-118-A1 Wireless Router is based on the MT7620A SoC.

Specification:

- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7610EN)
- 3x 10/100 Mbps Ethernet (3 LAN)
- 2x 10/100/1000 Mbps ICPlus IP1001 Ethernet PHY (1 WAN AND 1 LAN)
- 1x internal, non-detachable antenna
- 2x external, non-detachable antennas
- 1x USB 2.0
- UART (J1) header on PCB (57600 8n1)
- 7x LED (5x GPIO-controlled), 2x button
- JBOOT bootloader

Known issues:
- WIFI 5G LED not working
- flash is very slow

The status led has been assigned to the dwr-118-a1:green:internet led.
At the end of the boot it is switched off and is available for other
operation. Work correctly also during sysupgrade operation.

Installation:
Apply factory image via http web-gui or JBOOT recovery page

How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
  blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-12-03 15:34:56 +01:00
Chen Minqiang 40692f0fb5 ramips: mt7620: select only the matching mt76 driver
Because every device has selected the corresponding mt76 driver, we can
now disable the mt76 metapackage by default to make sure that other
devices (those don't need mt76) avoid selecting unwanted packages.

We can find the hardware specifies and determine the dependencies on
these sites:
  https://wikidevi.com/wiki/
  https://openwrt.org/toh/hwdata/

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2018-12-03 15:34:56 +01:00
Chen Minqiang 7a32a73e52 ramips: mt7620: drop mt76 driver for boards without mt76 wireless
These boards don't have a mt76 wireless at all and don't need any of the
mt76 family drivers.

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2018-12-03 15:34:56 +01:00
Mathias Kresin 55101877d3 ramips: mt7620: disable PCIe if nothing is attached
All boards neither expose the PCIe as Mini-PCIe nor have anything
attached to the PCIe Bus. Disable PCIe for those by dropping the node
from the dts files.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-03 15:34:56 +01:00
Chen Minqiang 14b81c909f ramips: mt7620: add missing pci wifi nodes to dts files
These devices has pci wifi but not defined in dts:
 HC5761
 HC5861
 TINY-AC

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2018-12-03 15:34:56 +01:00
Mathias Kresin 78ca6a5578 ramips: merge relocate compile into build recipe
Compile the loader if the relocate-kernel image recipe is used and get
rid of the legacy build code to do so.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-30 09:04:29 +01:00
Pawel Dembicki 465d57370f ramips: specify "firmware" partition format in JBOOT devices
Specify firmware partition format by compatible string.

List of devices:
-DWR-116-A1
-DWR-118-A2
-DWR-512-B
-DWR-921-C1
-LR-25G001

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-11-30 00:22:04 +01:00
Valentín Kivachuk 30a7ab8f61 ramips: add support for MTC Wireless Router WR1201
MTC Wireless Router WR1201 is the OEM name of the board. It is also sold
rebranded as STRONG Dual Band Gigabit Router 1200.

Specification:
- SoC: MediaTek MT7621A (880 MHz)
- Flash: 16 MiB
- RAM: 128 MiB
- Wireless: 2.4Ghz(MT7602EN) and 5Ghz (MT7612EN)
- Ethernet speed: 10/100/1000
- Ethernet ports: 4+1
- 1x USB 3.0
- 1x microSD reader
- Serial baud rate of Bootloader and factory firmware: 57600

The OEM webinterface writes only as much bytes as listed in the
uImage header field to the flash. Also, the OEM webinterface
evaluates the name field of uImage header before flashing (the
string "WR1201_8_128")

To flash via webinterface, is mandatory to use first initramfs.bin
and after (from the OpenWrt) the sysupgrade.bin

Some notes:
- Some microSD will not work:

  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising SDIO card
  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising MMC card
  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising SDIO card
  mtk-sd 1e130000.sdhci: card claims to support voltages below defined range
  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising MMC card
  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising SDIO card
  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising MMC card

Signed-off-by: Valentín Kivachuk <vk18496@gmail.com>
2018-11-30 00:20:28 +01:00
INAGAKI Hiroshi d70ec3008d ramips: specify "firmware" partition format
Specify firmware partition format by compatible string.

formats in ramips:

- denx,uimage
- tplink,firmware
- seama

It's unlikely but the firmware splitting might not work any longer for
the following boards, due to a custom header:

- EX2700: two uImage headers
- BR-6478AC-V2: edimax-header
- 3G-6200N: edimax-header
- 3G-6200NL: edimax-header
- BR-6475ND: edimax-header
- TEW-638APB-V2: umedia-header
- RT-N56U: mkrtn56uimg

But it rather looks like the uImage splitter is fine with the extra
header.

The following dts are not touched, due to lack of a compatible string in
the matching firmware splitter submodule:

- CONFIG_MTD_SPLIT_JIMAGE_FW
    DWR-116-A1.dts
    DWR-118-A2.dts
    DWR-512-B.dts
    DWR-921-C1.dts
    LR-25G001.dts
- CONFIG_MTD_SPLIT_TRX_FW
    WCR-1166DS.dts
    WSR-1166.dts
- CONFIG_MTD_SPLIT_MINOR_FW
    RBM11G.dts
    RBM33G.dts
- CONFIG_MTD_SPLIT_LZMA_FW
    AR670W.dts
- CONFIG_MTD_SPLIT_WRGG_FW
    DAP-1522-A1.dts

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-11-29 13:15:44 +01:00
Mathias Kresin 1977be8bd0 ramips: unifiy sysupgrade file extensions
Use .bin as file extension where possible. The user doesn't need to that
sysupgrade images for NAND boards are tarballs.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-29 13:15:44 +01:00
Mathias Kresin 7f00123d63 ramips: remove duplicate image build variables
Remove image build variables which are set to the same value as the
default image build recipe.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-29 13:15:44 +01:00
Petr Štetiar 221d3e0234 ramips: bdcom-wap2100: Change DTS license to GPL-2.0-or-later OR MIT
Having MIT as alternative is sometimes preferred by upstream maintainers
and allows sharing that simple code with other projects. We don't really
want multiple DTS versions for the same device.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-29 13:15:44 +01:00
Felix Fietkau 5c9ad4fa6e ramips: fix MTD EEPROM offset for TL-WR840N v5
The previous offset was invalid and pointed to the end of the partition,
which was causing issues with mt76

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-29 11:45:44 +01:00
Petr Štetiar 8ba6e95eed ramips: bdcom-wap2100: Enable mt7610e 5GHz radio
The 5GHz radio of this device uses an mt7610e PCI-E chip, which has
been recently started to be supported.

 mt76x0e 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4
 mt76x0e 0000:01:00.0: ASIC revision: 76100002
 mt76x0e 0000:01:00.0: Firmware Version: 0.1.00
 mt76x0e 0000:01:00.0: EEPROM ver:01 fae:00

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-28 23:37:29 +01:00
Petr Štetiar 26ad357192 ramips: bdcom-wap2100: Set firmware partition format to denx,uimage
Specify firmware partition format to denx,uimage in compatible DTS property.

 2 uimage-fw partitions found on MTD device firmware
 Creating 2 MTD partitions on "firmware":
 0x000000000000-0x00000017f72b : "kernel"
 0x00000017f72b-0x000000f70000 : "rootfs"

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-28 23:37:29 +01:00
Petr Štetiar 795211093f ramips: bdcom-wap2100: Fix boot failure by adding partitions compatible property
Flash partitions were moved under partition table node, but addition of
compatible property was omitted which lead to following boot failure:

 VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
 Please append a correct "root=" boot option; here are the available partitions:
 1f00           16384 mtdblock0
  (driver?)
 Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)

Fixes: e4d9217f (ramips: improve BDCOM WAP2100-SK support)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-28 23:37:29 +01:00
David Yang 824b580079 ramips: fix switch port order for HuaWei HG255D
The order of port marks and LEDs is reversed according to the board.

Signed-off-by: David Yang <mmyangfl@gmail.com>
2018-11-28 01:11:38 +01:00
Roger Pueyo Centelles cb6a8aa584 ramips: mt7620: add DIR-810L's mt7610e 5 GHz radio
The 5 GHz radio of this device uses an mt7610e pci-e chip, which has
been recently added support.

Tested on the actual device as AP and client, TCP throughput ~90 Mbps
U/D.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2018-11-28 01:11:38 +01:00
Nishant Sharma df3e0b5806 ramips: add support for UniElec U7621-06-512M-64M variant
Add support for UniElec U7621-06 variant with 512MB RAM and 64MB flash.

Additional specs are below:

CPU: MT7621 (880Mhz)
Bootloader: Ralink U-Boot
Flash: 64MB
 - U-Boot identifies as Macronix MX66L51235F
 - kernel identifies as MX66L51235l (65536 Kbytes)
RAM: 512MB

Rest of the details as per commit 46ab81e405 ("ramips add support for
UniElec U7621-06")

Signed-off-by: Nishant Sharma <nishant@unmukti.in>
[use generic board detection, add firmware partition compatible, extend
firmware partition to use all of the remaining flash space, add a
maximum image size matching the firmware partition size]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-28 01:11:38 +01:00
Mathias Kresin 509d02a3d1 ramips: use generic board detection for Unielec u7621-06
Use the generic board detection for the board instead of the target
specific one. Mark the sysupgrade image compatible with the former used
userspace boardname to allow an upgrade from earlier versions.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-28 00:50:35 +01:00
Thomas Vincent-Cross a160f50d4f ramips: add support for Wavlink WL-WN570HA1
This commit adds support for the Wavlink WL-WN570HA1, a dual-band PoE
wireless router with the following specifications:

 - CPU: MediaTek MT7688AN 580MHz
 - Flash: 8MB
 - RAM: 64MB
 - Ethernet: 1x 10/100Mbps
 - 2.4 GHz: 802.11b/g/n SoC, 1T1R, 27 dBm
 - 5 GHz: 802.11a/n/ac MT7610E, 1T1R, 25 dBm
 - Antennas: 2x external (1 per radio), detachable
 - LEDs: 3 programmable + Wi-Fi, WAN/LAN, Power
 - Buttons: Reset

Flashing instructions:

Factory U-boot launches a TFTP client if reset button is pressed during power-on.
Rename the sysupgrade file and configure TFTP as follows:

 - Client (WL-WN570HA1) IP: 192.168.10.101
 - Server IP: 192.168.10.100
 - Filename: firmware.bin

Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
[use generic board detection, add firmware partition compatible]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-28 00:50:35 +01:00
Russell Senior e0def989e8 ramips: fix alphabetic ordering of skylab skw92a
Fix the alphabetic ordering of skylab skw92a in ramips_setup_interfaces.

Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-11-27 21:11:54 +01:00
Matthias Badaire 1100ba43db ramips: fix RavPower WD03 SoC dtsi include
The RavPower WD03 is a mt7620n based baord. With the change applied, I2C
should work now with the RavPower WD03.

Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
[reworded commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-27 21:11:54 +01:00
Mathias Kresin aa82fdf110 ramips: fix GB-PC1/PC2 build error
With ed25e3ac02 ("ramips: fix some clocks in mt7621.dtsi") the
cpuclock node was dropped from the mt7621.dtsi without removing the
references to this node from the GB-PC1/PC2 dts files.

Remove them now, to fix the build error.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 19:40:31 +01:00
Mathias Kresin d7494f30f5 ramips: fix Lava LR-25G001 invalid led names
It has to be <board>:<colour>:<function> and is expected exactly this
way by the userspace scripts.

While at it, fix some whitespace issues in the dts file and rename the
flash node as required upstream.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 19:40:31 +01:00
Mathias Kresin be3e69d991 ramips: rt2880: fix pci cells definition
Set the correct number of cells to fix "property has invalid length" dtc
compiler warnings.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 15:54:22 +01:00
Mathias Kresin e4d9217fe5 ramips: improve BDCOM WAP2100-SK support
Use the generic board detection instead of the target specific one as
all recent additions are doing.

Setup the USB led via devicetree (a58535771f) and include the required
driver by default. Merge the led userspace setting with an existing
identical case.

Use the wps led for boot status indication.

Move the partitions into a partition table node (6031ab345d) and drop
needless labels. Drop misplaced cells properties (53624c1702).

Cleanup the pinmux and only switch pins to gpio functions which a
referenced as gpio in the dts.

Match the maximum image size with the size of the firmware partition.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 15:54:22 +01:00
Mathias Kresin 71ba834cf1 ramips: add Sanlinking Technologies D240 pinmux quirk
The sd function of the nd_sd group configures two of the groups pins as
gpios. The pins are used as PCIe reset/power.

Due to the driver load order, the pins are configured way to late if
triggered by the sd-card driver.

To not introduce another kind of driver load order dependency and
configure the pins as early as possible, means during pinmux driver
load.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 15:54:22 +01:00
Mathias Kresin d6ce04dad8 ralink: fix mt7620 nd_sd pinmux
In case the nd_sd group is set to the sd-card function, Pins 45 + 46 are
configured as GPIOs. If they are blocked by the sd function, they can't
be used as GPIOs.

Reported-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 15:54:22 +01:00
Mathias Kresin 9ebce69611 ramips: revert fix rt3883 pci pinmux
This reverts commit dcdc6d9dad.

Even if described this way in the datasheet, it causes a bootloop on a
RT-N56U (v1):

  of-flash 1c000000.nor-flash: do_map_probe() failed for type cfi_probe
  of-flash 1c000000.nor-flash: do_map_probe() failed
  VFS: Cannot open root device “(null)” or unknown-block(0,0): error -6

Fixes: FS#1930

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 15:54:22 +01:00
Mathias Kresin 8ec1a66c34 ramips: improve Skylab SKW92A support
Use the generic board detection instead of the target specific one as
all recent additions are doing.

Add the wireless led according the gpio number from the datasheet.
Rename the board part of the leds to match the name used for the
compatible string. Finally, do not hijack the wps led for boot status
indication longer than necessary.

Merge userspace config into existing cases.

Include the manufacture Name in the dts model string.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 15:54:22 +01:00
John Crispin 749a29f76c Revert "ramips: mt7621-spi: replace the driver with upstream staging one"
This reverts commit a44f000077.

This breaks some mt7621 devices.

Signed-off-by: John Crispin <john@phrozen.org>
2018-11-26 14:43:42 +01:00
Zheng Qian 48a7a2a75d ramips: fix switch ports mapping for newifi d2
Signed-off-by: Zheng Qian <sotux82@gmail.com>
2018-11-26 12:31:19 +01:00
Chuanhong Guo a44f000077 ramips: mt7621-spi: replace the driver with upstream staging one
That driver is more efficient thanks to the refactor of spi reading operation.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-11-26 12:24:30 +01:00
Pawel Dembicki 20b09a2125 ramips: add support for Lava LR-25G001
The Lava LR-25G001 Wireless Router is based on the MT7620A SoC.

Specification:

- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7610EN)
- 5x 10/100/1000 Mbps AR8337 Switch (1 WAN AND 4 LAN)
- 2x external, detachable antennas
- 1x USB 2.0
- UART (J3) header on PCB (57600 8n1)
- 8x LED (3x GPIO-controlled), 2x button
- JBOOT bootloader

Known issues:
- Work only three Gigabit ports (3/5, 1 WAN and 2LAN)

Installation:
Apply factory image via http web-gui or JBOOT recovery page

How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
  blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-11-26 12:16:52 +01:00
Pawel Dembicki b85fe43ec8 ramips: mt7620: add force use of mdio-mode
Some boards have external switches different than mt7530.

This patch allow to use mdio-mode without 0x1f register.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-11-26 12:16:52 +01:00
Weijie Gao ed25e3ac02 ramips: fix some clocks in mt7621.dtsi
As the cpu clock calculation has been fixed, the clock for gic and spi
should be also fixed.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-11-26 12:13:52 +01:00
Weijie Gao c7ca224299 ramips: fix cpu clock of mt7621 and add dt clk devices
For a long time the mt7621 uses a fixed cpu clock which causes a problem
if the cpu frequency is not 880MHz.

This patch fixes the cpu clock calculation and adds the cpu/bus clkdev
which will be used in dts.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-11-26 12:13:52 +01:00
Weijie Gao f5af8be636 ramips: fix register range of memc node in mt7621.dtsi
The memc node from mt7621.dtsi has incorrect register resource.
Fix it according to the programming guide.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-11-26 12:13:52 +01:00
Weijie Gao e217d69a4a ramips: merge two patches 101-mt7621-timer and 998-mt7621-needs-jiffies
These two patches both modified the mt7621.c, and the patch file
998-mt7621-needs-jiffies.patch adds only one line which is used by the
another patch file. So merge them into one file.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-11-26 12:13:52 +01:00
Lorenzo Bianconi e612e60517 ramips: add mt76x0 node to RT-AC51U device tree
Introduce mt76x0e device tree node in RT-AC51U dts.
Define mt76x0e mtd partition and offset

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
2018-11-26 12:05:47 +01:00
Daniel Santos 89eb1a6d72 ralink: Add support for GPIO as interrupt-controller
The gpio-ralink driver has everything it needs to be used as an
interrupt controller except for device tree support.  This simple patch
adds that support by configuring the irq domain to use two cells and
adding the appropriate documentation to the devicetree bindings.

Signed-off-by: Daniel Santos <daniel.santos@pobox.com>
2018-11-26 12:05:45 +01:00
Petr Štetiar 16b950c981 ramips: Add support for ZTE ZXECS EBG3130 aka BDCOM WAP2100-SK
On the bottom sticker it's branded as ZTE ZXECS EBG3130 device, but in factory
OpenWrt image it's referenced as BDCOM WAP2100-SK device.

Specifications:

- SoC: MediaTek MT7620A
- RAM: 128 MB
- Flash: 16 MB
- Ethernet: 5 FE ports
- Wireless radio: 2T2R 2.4 GHz and 1T1R 5 GHz (MT7610EN, unsupported)
- UART: 1 x UART on PCB marked as J2 (R=RX, T=TX, G=GND) with 115200 8N1 config
- LEDs: Power, FE ports 1-5, WPS, USB, RF 2.4G, RF 5G
- Other: USB port, SD card slot and 2x external antennas (non-detachable)

Flashing instructions:

A) The U-Boot has HTTP based firmware upgrade

  A1) Flashing notes

  We've identified so far two different batches of units, unfortunately
  each batch has different U-Boot bootloader flashed with different
  default environment variables, thus each batch has different IP address
  for accessing web based firmware updater.

  * First batch has web based bootloader IP address 1.1.1.1
  * Second batch has web based bootloader IP address 192.168.1.250

  In case you can't connect to either of those IPs, you can try to get
  the default IP address via two methods:

  A1.1) Serial console, then the IP address is visible during the boot

   ...
   HTTP server is starting at IP: 1.1.1.1
   raspi_read: from:40004 len:6
   HTTP server is ready!
   ...

  A1.2) Over telnet/SSH using this command:

   root@bdcom:/# grep ipaddr= /dev/mtd0
   ipaddr=1.1.1.1

  A2) Flashing with browser

  * Change IP address of PC to 1.1.1.2 with 255.255.255.0 netmask
  * Reboot the device and try to reach web based bootloader in the
    browser with the following URL http://1.1.1.1

  * Quickly select the firmware sysupgrade file and click on the
    `Update firmware` button, this all has to be done within 10 seconds,
    bootloader doesn't wait any longer

   If done correctly, the web page should show UPDATE IN PROGRESS page
   with progress indicator. Once the flashing completes (it takes roughly
   around 1 minute), the device will reboot to the OpenWrt firmware

  A3) Flashing with curl

   sudo ip addr add 1.1.1.2/24 dev eth0
   curl \
      --verbose \
      --retry 3 \
      --retry-delay 1 \
      --retry-max-time 30 \
      --connect-timeout 30 \
      --form "firmware=@openwrt-ramips-mt7620-BDCOM-WAP2100-SK-squashfs-sysupgrade.bin" \
      http://1.1.1.1

   Now power on the router.

B) The U-boot is based on Ralink SDK so we can flash the firmware using UART.

   1. Configure PC with a static IP address and setup an TFTP server.
   2. Put the firmware into the tftp directory.
   3. Connect the UART line as described on the PCB (G=GND, R=RX, T=TX)
   4. Power up the device and press 2, follow the instruction to set device and
      tftp server IP address and input the firmware file name. U-boot will then load
      the firmware and write it into the flash.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-26 12:05:44 +01:00
Roman Yeryomin ae2b43b873 ramips: fix ethernet for f5d8235-v2 board
Belkin F5D8235 v2 has two ethernet switches on board.
One internal rt3052 and rtl8366rb on rgmii interface.
Looks like internal switch settings were lost in
translation to device tree infrastructure.

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-11-26 09:58:17 +01:00
Russell Senior e42327aa89 ramips: add support for Skylab SKW92A in EVB
Specifically, SKW92A_E16, described here:

  http://www.skylabmodule.com/wp-content/uploads/SkyLab_SKW92A_V1.04_datasheet.pdf

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x u.FL
- Power by micro-USB connector at USB1 on EVB
- UART via micro-USB connector at USB3 on EVB (57600 8n1)
- 5x Ethernet LEDs
- 1x WLAN LEDs
- 1x WPS LED connected by jumper wire from I2S_CK on J20 to WPS_LED pin hole next
  to daughter board on EVB
- WPS/Reset button (S2 on EVB)
- RESET button (S1 on EVB) is *not* connected to RST hole next to daughter board

Flash instruction:

>From Skylab firmware:

1. Associate with SKYLAP_AP
2. In a browser, load: http://10.10.10.254/
3. Username/password: admin/admin
4. In web admin interface: Administration / Upload Firmware, browse to
   sysupgrade image, apply, flash will fail with a message:
   Not a valid firmware. *** Warning: "/var/tmpFW" has corrupted data!
5. Telnet to 10.10.10.254, drops you into a root shell with no credentials
6. # cd /var
7. # mtd_write -r write tmpFW mtd4
   Unlocking mtd4 ...
   Writing from tmpFW to mtd4 ... [e]
8. When flash has completed, you will have booted into your firmware.

>From U-boot via TFTP and initramfs:

1. Place openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin on a TFTP server
2. Connect to serial console at USB3 on EVB
3. Connect ethernet between port 1 (not WAN) and your TFTP server (e.g.
   192.168.11.20)
4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC
5. Apply power to EVB
6. Interrupt u-boot with keypress of "1"
7. At u-boot prompts:
   Input device IP (10.10.10.123) ==:192.168.11.21
   Input server IP (10.10.10.3) ==:192.168.11.20
   Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin
8. Move ethernet to port 0 (WAN) on EVB
9. At new OpenWrt console shell, fetch squashfs-sysupgrade image and flash
   with sysupgrade.

>From U-boot via TFTP direct flash:

1. Place openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin on a TFTP server
2. Connect to serial console at USB3 on EVB (57600 8N1)
3. Connect ethernet between port 1 (not WAN) an your TFTP server (e.g.
   192.168.11.20)
4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC
5. Apply power to EVB
6. Interrupt u-boot with keypress of "2"
7. At u-boot prompts:
   Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y
   Input device IP (10.10.10.123) ==:192.168.11.21
   Input server IP (10.10.10.3) ==:192.168.11.20
   Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin
8. When transfer is complete or as OpenWrt begins booting, move ethernet to
   port 0 (WAN).

Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-11-26 09:47:27 +01:00
Daniel Golle 7c4251d881 ramips: select kmod-mt76x0e for TP-Link ArcherC20i and wr902ac-v3
Both devices come with a MediaTek MT7610E 5GHz 802.11ac 1T1R radio
which wasn't supported at the time the devices were added to OpenWrt.
Now that we got it, include kmod-mt76x0e in images for those devices.

Reported-by: Arian Sanusi <openwrt@semioptimal.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-11-25 15:24:49 +01:00
Rafał Miłecki 9a3c805584 ramips: use separated mtd patch reverting write_page() removal
This helps understanding mtd changes needed to get downstream NAND
driver working.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-09 13:31:47 +01:00
Koen Vandeputte b4e17a7440 ramips: fix netgear r6120 factory image generation
as indicated in commit c5bf408ed6 "(ramips: fix image generation for mt76x8")
more rework was needed to fix the other issues.

Building on another machine, but using the same arch, showed
the application failing again for different reasons.

Fix this by completely rewriting the application, fixing following found issues:

- buffer overflows, resulting in stack corruption
- flaws in memory requirement calculations (too small, too large)
- memory leaks
- missing bounds checking on string handling
- non-reproducable images, by using unitilized memory in checksum calculation
- missing error handling, resulting in succes on specific image errors
- endianness errors when building on BE machines
- various minor build warnings
- documentation did not match the code actions (header item locations)
- allowing input to be decimal, hex or octal now

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-11-08 13:32:22 +01:00
Felix Fietkau b318edb999 ramips: add missing DTS frequency limit for the 5 GHz radio on Archer C20i
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-06 22:25:49 +01:00
Koen Vandeputte c764b2b531 kernel: bump 4.14 to 4.14.79
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-11-05 16:00:00 +01:00
Martin Weinelt 0411813c6f
ramips: fix leds on GL.iNet GL-MT300N-V2
The WAN LED now shows the link state. It's color is green,
not blue.

Signed-off-by: Martin Weinelt <hexa@darmstadt.ccc.de>
2018-11-02 21:43:15 +01:00
Baptiste Jonglez b2c68ceea7 kernel: Add support for Winbond w25q128jv SPI NOR flash
Newer batches of several Mikrotik boards contain this yet-unsupported
flash chip, for instance:

- rb941-2nd (hAP lite)
- rb952ui-5ac2nd (hAP ac lite)
- RBM33G

and probably other Mikrotik boards need this patch as well.

The patch was submitted upstream by Robert Marko: https://patchwork.ozlabs.org/patch/934181/

Closes: FS#1715
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Cc: Robert Marko <robimarko@gmail.com>
2018-10-20 16:13:39 +02:00
Mathias Kresin 80c61c161a treewide: use wpad-basic for not small flash targets
Add out of the box support for 802.11r and 802.11w to all targets not
suffering from small flash.

Signed-off-by: Mathias Kresin <dev@kresin.me>

Mathias did all the heavy lifting on this, but I'm the one who should
get shouted at for committing.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-10-16 15:07:41 +01:00
Felix Fietkau d251a11f60 ramips: refresh mt7621 kernel config
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-10-15 12:54:12 +02:00
Koen Vandeputte f983956a8b kernel: bump 4.14 to 4.14.75
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-10 14:45:11 +02:00
Mathias Kresin b07b3ddaad ramips: don't hijack the status led
Don't hijack the status led to indicate the wireless state. If we don't
have a dedicated wireless led, it's as simply as the wireless status
can't be indicated.

Such a led misuse should be set by the user and not shipped by default.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-10-07 11:35:03 +02:00
Mathias Kresin c074239c79 ramips: move status led unset to devicetree
Release the led used for boot status indication via devicetree instead
of setting a default off trigger in userspace.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-10-07 11:34:18 +02:00
Mathias Kresin 8f4dfadd5a ramips: add support for indicating the boot state using multiple leds
Use diag.sh version used for other targets supporting different leds
for the different boot states.

The existing led sequences should be the same as before.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-10-07 11:34:18 +02:00
Mathias Kresin 772b27c207 ramips: set F5D8235 v1 usb led trigger via devicetree
Assign the usbdev trigger via devicetree and drop the userspace
handling of the usb leds.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-10-07 11:34:18 +02:00
Mathias Kresin 04eab0a1c9 ramips: set rt2880 pci controller of_node
Set the PCI controller of_node such that PCI devices can be
instantiated via device tree.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-10-07 11:34:18 +02:00
Mathias Kresin a58535771f ramips: set usb led trigger via devicetree
Assign the usbdev trigger via devicetree for all subtargets and drop
the userspace handling of the usb leds.

With the change all usb ports are triggering the usb led instead of
only usb 1.1 XOR usb 2.0 XOR usb 3.0 as it was before.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-10-07 11:34:18 +02:00
Koen Vandeputte a2adeffffc kernel: bump 4.14 to 4.14.74
Refreshed all patches.

Fixes CVE:

- CVE-2018-7755

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-04 16:15:03 +02:00
Steffen Förster 8480907e70 ramips: fix Archer C20 sysupgrade
The sysupgrade image failed the check due to the wrong string in the
supported devices. This patch provides the correct name by dropping the
SUPPORTED_DEVICES to use the default generated name.

Signed-off-by: Steffen Förster <steffen@chemnitz.freifunk.net>
[drop the SUPPORTED_DEVICES, the old name was never used in a release]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-26 20:35:07 +02:00
Emil Muratov 8e6bc1a5be ramips: fix power LED DTB for wt3020
Since c134210 power LED is no longer lights after boot-up.
Reversing gpio polarity makes it work as it should be.

Signed-off-by: Emil Muratov <gpm@hotplug.ru>
2018-09-26 20:35:07 +02:00
Joseph C. Lehner d6e39e7466 ramips: ex2700: actually remove kmod-mt76*
When building using the multiple devices option with per-device root
filesystem, only the meta package mt76 is omitted but not the
dependencies selected by the package.

Explicitly exclude all 3 mt76 packages, plus the metapackage.
Otherwise, these modules will be included in the build, wasting
a few hundred kilobytes.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
[mention the root cause of the issue in the commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-26 20:35:07 +02:00
Koen Vandeputte 0cda4af005 kernel: bump 4.14 to 4.14.70
Refreshed all patches.

Added new patch:
- 192-Revert-ubifs-xattr-Don-t-operate-on-deleted-inodes.patch

This fixes a bug introduced in upstream 4.14.68 which caused targets using
ubifs to produce file-system errors on boot, rendering them useless.

Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-09-17 15:47:44 +02:00
Tobias Wolf 93bfafb8dc ramips: Fix early memory calculation for certain MIPS platforms
Kernel upstream commit 67a3ba25aa95 ("MIPS: Fix incorrect mem=X@Y handling") introduced a new issue for rt288x where "PHYS_OFFSET" is 0x0 but the calculated "ramstart" is not. As the prerequisite of custom memory map has been removed, this results in the full memory range of 0x0 - 0x8000000 to be marked as reserved
for this platform.

This patch adds the originally intended prerequisite again.

Signed-off-by: Tobias Wolf <dev-NTEO@vplace.de>
2018-09-10 10:07:42 +02:00
Carlo Nel 6bbb220255 ramips: add support for TP-Link TL-MR3020 v3
TP-Link TL-MR3020 v3 is a pocket-size router based on MediaTek MT7628N.

This PR is based on the work of @meyergru[1], with his permission.

Specification:
- MediaTek MT7628N/N (575 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 1x 10/100 Mbps Ethernet

Flash instruction:

The only way to flash the image in TL-MR3020 v3 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-mr3020-v3-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

[1] https://github.com/meyergru/lede-source/commits/TL-MR3020-V3

Signed-off-by: Carlo Nel <carlojnel@gmail.com>
2018-09-06 21:36:42 +02:00
Mathias Kresin 287b7aa583 ramips: drop obsolete sd card driver code
The pinmux for all SoCs using this driver is now set via the pinmux. It
makes this code obsolete.

Some of the code targeting the mt76x8 SoCs is still required. The sd
card pins share the pads with the EPHY. These pads need to be switched
to digital mode if the pins are used for sd cards.

The eMMC 8-bit mode has to be enabled via pinmux instead of a kernel
option. The uart2 group need to be set to function "sdxc d5 d4", pwm1
to "sdxc d6" and pwm0 to "sdxc d7" to do so. It can't be done by as
part of a default pinmux, as it would break the normal operation of
uart2.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-06 21:35:53 +02:00
Mathias Kresin 563a5b5f94 ramips: add mt7620/1 sdhci pinmux
Set the pins to the required mode via the pinmux driver. It allows to
get rid of the pinmux related code in the sd card driver.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-06 21:35:53 +02:00
Mathias Kresin a14097e8e0 ramips: fix mt7620a ND/SD pins pinmuxes
Drop the nd_sd gpio pinmux in case sdcard is used. They're mutually
exclusive and for most of the boards not even used as GPIOs.

If the pins are in sdcard mode, the pins ND_WE_N and ND_CS_N are still
GPIOs (#45 and #46).

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-06 21:35:53 +02:00
Mathias Kresin 2cc7980dcb ramips: reference node by label
Reference the HC5661A sdhci node by label instead of by the full path.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-06 21:35:53 +02:00
Mathias Kresin 1d08951628 ramips: add rt3352 SPI_CS1 pinmux
The rt3352 has a pin that can be used as second spi chip select,
watchdog reset or GPIO. The pinmux setup was missing the definition of
said pin but it is already used in the SoC dtsi.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-06 21:35:53 +02:00
Felix Fietkau b605a84a74 ramips: ethernet: unify tx descriptor buffer splitting
A buffer is split into multiple descriptors if it exceeds 16 KB.
Apply the same split for the skb head as well (to deal with corner cases
on fraglist support)

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-09-03 12:06:24 +02:00
Jo-Philipp Wich 4302c917cc Revert "ramips: mmc: Fix init for MT7628AN"
This reverts commit 3a8efaef00.

The change reportedly breaks UART2 on some boards. Furthermore it uses
bitwise logic on an uninitialized variable and fails to explain what it
is fixing exactly.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-08-30 13:19:26 +02:00
Jo-Philipp Wich 77e2bccde8 ramips: only limit lzma dictionary size on mt7621
The changed dictionary size leads to a different LZMA header which breaks
sysupgrade image magic checkibng on at least some RT288x boards.

Since the commit message only mentions testing on MT7621 and since the
change appears to break at least one other ramips subtarget, do not take
any chances and restrict the size limitation to only MT7621.

Fixes FS#1797
Fixes 09b6755946 ("ramips: limit dictionary size for lzma compression")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-08-30 10:57:35 +02:00
Mathias Kresin a6e11ccb13 ramips: fix rt3883 pinmux for second SPI
The rt3883 doesn't have a pinmux group named spi_cs1. The cs1 is part
of the pci group. The function pci-func enables the second chip select.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 21:00:58 +02:00
Mathias Kresin dcdc6d9dad ramips: fix rt3883 pci pinmux
The PCI pins need to be set to "PCI Host support one device" to allow
the use of one PCI device and flash memory.

The pci-fnc function is intended to be used if no PCI is used but
flash, nand or the codec functionality is.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 21:00:58 +02:00
Mathias Kresin c134210b8f ramips: drop pointless default led definitions
The LEDs should be triggered/lit by any kind of state change instead of
turned on/off unconditional.

If LEDs really need to be turned off by default, it should be done via
the default-state devicetree led property.

The handling of the wndr3700v5 and wt3020 power led is at least
strange. Something is for sure wrong with them. Either the leds are
misnamed, the default off trigger is a typo or the polarity of the
gpios is wrong. Drop the power led from userspace and wait for someone
with access to the hardware to fix it properly.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 09:39:32 +02:00