The name of the PCIe controller node in device tree changed between
kernel 4.9 and kernel 4.14. Migrate the configuration when an update
from kernel 4.9 to 4.14 or back is done to the new name to make
the existing wifi configuration compatible with the new names.
This replaces the "pcie-controller" part with "pcie" on all nodes if the
file exists in sys fs.
This is not done in the uci-defualts, because they are getting executed
to late in the boot process. The kernel module gets loaded before the
uci-defaults scripts are executed. When the mwlwifi driver gets loaded
it will trigger an event via hotplug to detect new devices and as the
paths are not in the uci configuration they will be added again.
When the migration is done before the script will detect that they are
already there.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for kernel 4.14 to the mvebu target.
This also replaces the old sfp and phylink patches with new versions
from Russell's clearfog-4.13 branch
http://git.arm.linux.org.uk/cgit/linux-arm.git/log/?h=clearfog-4.13
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is needed to prevent copying it into kernel 4.14.
These device tree files are already integrated into kernel 4.14 and we
would like to use the upstream versions only.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of creating an ubifs file system with format version 5 by
default on empty UBI volumes use the older format 4 by default. This
will make it possible to mount these file systems also on older kernel
versions.
When a user wants to do a sysupgrade from kernel 4.14 to kernel 4.9 the
old kernel has to read the file system created by the more recent kernel
which currently does not work for ubifs.
This fixes the problem by creating file systems which are compatible
with older kernel versions by default.
Kernel 4.14 will still be able to read and write UBI FS file system
version 5, it will just not be used when a ubifs partition is created
implicitly on an empty UBI volume.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The root= parameter overrides the automatic rootfs detection by partition
name, so drop it. Fixes boot from flash after renumeration changes of
partitions due to parser changes.
Fixes FS#1350.
Fixes: a27d59bb42 ("brcm63xx: switch to new partition layout specification")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Instead of writing to the currently booted partition set, this
implements full dual-boot support for sysupgrade by always writing to
the other, currently inactive, partition set and toggling the dualflag
after a successful flash.
The currently active/ booted partition set is determined by parsing
/proc/cmdline for its rootfs parameter (supplied by the DTS), instead
of reading from the 0:DUAL_FLAG mtd, in order to prevent (potentially)
bricking both partition sets.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Instead of hardcoding /dev/loop0, it's safer to query for the first
free loop device and assign that dynamically. While /dev/loop0 is a
reasonable assumption immediately following "losetup --detach-all",
detaching the mounted overlay is no longer strictly necessary once
dual-boot support has been added for the nbg6817.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Harmonize the variable usage for $kernel and $rootfs to always contain
the full device path, instead of just its basename.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
PHY drivers were grouped into vendor specific directories
by upstream commit 0b56e9a7e8358e59b21d8a425e463072bfae523c
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Add more registers and flags to ar71x_regs.h for QCA955x and QCA956x
SoCs. Values come from Qualcomm Atheros u-boot code.
Patches can be merged into
622-MIPS-ath79-add-more-register-defines-for-QCA956x-SoC.patch
Signed-off-by: Julien Dusser <julien.dusser@free.fr>
D-Link DAP-1522 is a wireless bridge/access point with 4 LAN
ports and a dual-band wireless chipset.
Specifications:
- Ralink RT2880
- 32 MB of RAM
- 4 MB of Flash
- 4x 10/100/1000 Mbps Ethernet (RTL8366SR)
- 802.11abgn (RT2850)
Flash Instructions:
1. Download lede-ramips-rt288x-dap-1522-a1-squashfs-factory.bin
2. Open the web interface and upload the image
Signed-off-by: George Hopkins <george-hopkins@null.net>
EG-200 is a DIN rail mountable device with one ethernet port, wifi,
an RS-485 port, and an internal USB attached uSD card reader.
Two leds, "modbus" and "etactica" are managed by userspace applications
in factory firmware.
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Karl Palsson <karlp@etactica.com>
The tftp.bin image for Buffalo WHR-G300N was not built, so I was fixed
it after rewriting to new image build code. And the code for
factory-EU.bin was broken, so I deleted it.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
- Remove kernel 4.9 support
- Apply specific 4.14 changes directly to source
- Refreshed all
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The Cavium OCTEON TX is an ARM 64-bit SoC leveraging CPU cores and
periperhals from the Cavium ThunderX SoC.
This initial support provides a 4.14 kernel and kernel+initramfs that is
bootable on the Gateworks Newport GW630x as well as the Cavium sff8104
reference board.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Device Tree file for I2SE Duckbill boards was updated upstream.
Let's use the upstream version for upcoming kernel 4.14 by keeping
our current version for v4.9 still around.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
The GnuBee Personal Cloud Two crowdfunded on https://www.crowdsupply.com
It is a low-cost, low-power, network-attached storage device.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: DDR3 512 MB
- Flash: 32 MB
- Six SATA ports for 3.5" Drives
- One SDcard
- One USB 3.0
- Two USB 2.0
- Gigabit Ethernet: Three Ports
- UART 3.5mm Audio Jack or 3 pin header - 57600 8N1
- Three GPIOs available on a pin header
Flash instructions:
The GnuBee Personal Cloud Two ships with libreCMC installed.
libreCMC is a Free Software Foundation approved fork of LEDE/OpenWrt.
As such one can upgrade using the webinterface or sysupgrade.
Das U-Boot has multiple options for recovery or updates including :
- USB
- http
- tftp
Errata:
- While there are three ethernet ports, the third requires support for
the second GMAC. This will come in kernel 4.14.
- The first hard drive slot has a clearance issue with the two fan
headers. Workaround is to pull the headers out and connect the pins to
jumper wires.
- Using this device as a NAS is problematic with the 4.9 kernel as many
/dev/sdX reads throw silent errors. The current theory behind this is
some kind of unhandled DMA mapping error in the kernel. This is not an
issue with kernel 4.4.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Updated pfe kernel patch to clean up iounmap(pfe->ddr_baseaddr).
pfe->ddr_baseaddr was got through phys_to_virt() not ioremap(),
so iounmap() for pfe->ddr_baseaddr should be removed.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to add a known issue of make menuconfig
in README file. This is also a common issue for OpenWrt.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch changes the declarations of ndo_get_stats64 handlers
to the previous struct rtnl_link_stats64 * return type instead of
the mainline void return.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tis patch is to fix up some descriptions in README.
Per-device rootfs had been supported, and a known issue
had been found. These also should be updated accordingly.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Some layerscape devices (ls1012ardb/ls1012afrdm/ls1046ardb/ls1088ardb)
were using ext4 rootfs because there were issues using squashfs.
This patch is to drop using ext4 rootfs and use ubifs rootfs instead
which is more proper for SPI-NOR flash.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to remove USB configs for 32-bit device since
they're already in kmod package. Also removed TI platform
specific configs.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Patches changes
- Updated patches-4.9 to NXP LSDK1712 linux-4.9.
- Merged changes of patch 303 into integrated patch 201.
- Split changes of patch 706 into dpaa part and dpaa2
part, and merged these changes into integrated patches
701 and 705.
- Removed patch 819 since ehci-fsl driver could be compiled now.
- Refreshed these patches.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This device is identical as TP-Link RE450
RE355 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9558+QCA9880.
Specification:
720/600/200 MHz (CPU/DDR/AHB)
64/128 MB of RAM (DDR2)
8 MB of FLASH (SPI NOR)
3T3R 2.4 GHz
3T3R 5 GHz
1x 10/100/1000 Mbps Ethernet
7x LED, 3x button
UART header on PCB
Flash instruction:
Web:
Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin
and use OEM System Tools - Firmware Upgrade site.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
This will introduce a warning on 3.18, but fixes an error when
compiling for 4.9.
Fixes: cf9e0a59aa ("ar7: add kernel 4.9 support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
When clearfog was renamed to clearfog pro, it broke sysupgrade from
17.04 as the new images now get rejected as incompatible. Fix this by
adding the legacy boardname to the compatible devices.
Fixes: ec4a8c6dee ("mvebu: ClearFog renamed upstream to ClearFog Pro")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Add support for kernel 4.9 based on the more upstream comformant
partition defintions. Increases compressed kernel size by ~95k
compared to 4.4.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Partitions are supposed to be enclosed in an extra partitions node. Allow
the bcm63xxpart parser to cope with that.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The lookup needs to be called just "reset" for the common code.
Fixes: 054c0d4e31 ("brcm63xx: backport mdio-bus reset gpio support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The arm CPUs uses in the supported Mediatket SoCs have a FPU accordingly
to the datasheet, activate it also. The CPU subtype "neon-vfpv4" is
selected, but the toolcahin generated for this SoC will still be
compiled with soft float and not with the hard float ABI as we haven't
the fpu feature flag set. If this toolchain is reused by other targets
this will even affect other targets.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The BDFs for OpenMesh A42 were upstreamed [1] to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-01-26. The
ipq-wifi-openmesh_a42 package can now be dropped because OpenWrt already
ships the QCA4019 board-2.bin from this version.
[1] https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
COMFAST CF-E375AC is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9563 + QCA9886 + QCA8337.
Short specification:
2x 10/100/1000 Mbps Ethernet, with PoE support
128MB of RAM (DDR2)
16 MB of FLASH
3T3R 2.4 GHz, 802.11b/g/n
2T2R 5 GHz, 802.11ac/n/a, wave 2
built-in 5x 3 dBi antennas
output power (max): 500 mW (27 dBm)
1x RGB LED, 1x button
built-in watchdog chipset
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Ding Tengfei <dtf@comfast.cn>
TP-Link Archer C50 v3 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7612E.
Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power switch
* WAN LED in this devices is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Flash instruction:
The only way to flash LEDE image in ArcherC50v3 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt7628-ArcherC50v3-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
The D-Link devices with JBOOT bootloader use their own kernel
image header (stag + sch2 headers).
This driver find jImage header and set rootfs start after kernel file.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This commit marks the CPUs switchport explicit as untagged.
Otherwise, an eth0.1 interface is created and the devices
LAN-ports are not working.
Signed-off-by: David Bauer <mail@david-bauer.net>
Use "$(DTS_DIR)", defined at include/image.mk, instead of
"$(LINUX_DIR)/arch/$(LINUX_KARCH)/boot/dts" in order to generalize and
allow a better Device/* device-tree parameterization (i.e. DEVICE_DTS_DIR
and DTS_DIR).
Signed-off-by: Adrià Llaudet <adria.llaudet@gmail.com>
Update Linux kernel version from 4.9 to 4.14 for archs38.
config-4.14 was simply regenerated with "make kernel_menuconfig".
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: John Crispin <john@phrozen.org>
This config option was renamed in upstream Linux commit 681bec0367
("tracing: Rename update the enum_map file")
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Convert userspace code to use generic device-tree compatible board
detection method. Users of the existing code will have to use
sysupgrade -F once to switch to the new generic board naming.
Properly setup pinctrl fixing the switch port LEDs.
Fixes commit 9c4fe103cb (ramips: add support for ZBT-WE1226)
Reported-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Locally generated packets weren't forwarded to the isolated interfaces in a
bridge. Isolation should only prevent the flooding of incomming packets to
other interfaces in the bridge.
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Qualcomm claims this improves the D-cache footprint. Origina commit message below:
From: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Date: Fri, 7 Jun 2013 10:57:28 -0500
Subject: [ag71xx] cluster/align structs for cache perf
Cluster the frequently used, per-packet structures in ag71xx near
to each other, and cacheline-align them. Some other re-ordering
occurred to move "warmer" structures near the per-packet structures.
Signed-off-by: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This machfile also contains the code for the TL-WR842N/ND v2, which is in
ar71xx-generic and not in ar71xx-tiny.
Fixes: 0cd5e85e7a "ar71xx: create new ar71xx/tiny subtarget for 4MB flash
devices"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
To make it more accessible for nodejs users to configure and run a build
on mips target lacking hardware fpu
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Add the Embedded Wireless "Balin" platform
SoC: QCA AR9344 or AR9350
RAM: DDR2-RAM 64MBytes
Flash: SPI-NOR 16MBytes
WLAN: 2 x 2 MIMO 2.4 & 5 GHz IEEE802.11 a/b/g/n
Ethernet: 3 x 10/100 Mb/s
USB: 1 x USB2.0 Host/Device bootstrap-pin at power-up
PCI-Express: 1 x lane PCIe 1.2
UART: 1 x Normal, 1 x High-Speed
JTAG: 1 x EJTAG
GPIO: 10 x Input/Output multiplexed
The module comes already with the current vanilla OpenWrt firmware.
To update, use "sysupgrade" image directly in vendor firmware.
Signed-off-by: Catrinel Catrinescu <cc@80211.de>
Widora has updated their Widora Neo board recently.
The new model uses 32MB WSON-8 factor SPI flash
instead of the original 16MB SOP-8 factor SPI flash.
All the other hardware components are the same as
the first revision.
Detailed hardware specs listed below:
CPU: MTK MT7688AN
RAM: 128MB DDR2
ROM: 32MB WSON-8 factor SPI Flash (Winbond)
WiFi: Built-in 802.11n 150Mbps?
Ethernet: 10/100Mbps x1
Audio codec: WM8960
Other IO: USB OTG;
USB Power+Serial (CP2104);
3x LEDs (Power, LAN, WiFi);
2x Keys (WPS, CPU Reset)
1x Audio In/Out
1x IPEX antenna port
1x Micro SD slot
Signed-off-by: Jackson Ming Hu <huming2207@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Rename the Widora neo by adding a flash size prefix. Move the common parts
into a dtsi to be prepare everything for upcomming support of the 32MB
version.
Migrate the Widora neo to the generic board detection as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
When CGROUPS is enabled the new option CONFIG_CGROUP_NET_CLASSID is
selectable and not handled.
Add this option to the 4.9 kernel configuration.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
commit e15c63a375
ar71xx: add support for MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC)
changed the existing rb-nor-flash-16M-ac image in a way that it would
now only support the rb-wapg-5hact2hnd.
The board show however rather be added to the existing boards in the
rb-nor-flash-16M image template.
Reported-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The USB Ethernet is not working with the patches proposed for upstream,
fix this and activate the SPI node as this board always has a SPI flash.
Both patches are also targeted for upstream kernel 4.16 and 4.17.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of using our own device tree definitions use the one provided in
the upstream kernel for 4.16.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Ethernet support was initial added in kernel 4.13, but deactivated
before the final release. This is backports the changes which are
activating it again from kernel 4.15.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is based on the code for kernel 4.9, but a lot of 4.9 patches are
backports from more recent kernel version and can be removed now.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Just refresh the sunxi kernel configuration.
This also moves the CONFIG_CRYPTO_DEV_SUN4I_SS_PRNG option to the
config-4.9 file.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The patch adds support for the MikroTik RB911-2Hn (911 Lite2)
and the RB911-5Hn (911 Lite5) boards:
https://mikrotik.com/product/RB911-2Hnhttps://mikrotik.com/product/RB911-5Hn
The two boards are using the same hardware design, the only difference
between the two is the supported wireless band.
Specifications:
* SoC: Atheros AR9344 (600MHz)
* RAM: 64MiB
* Storage: 16 MiB SPI NOR flash
* Ethernet: 1x100M (Passive PoE in)
* Wireless: AR9344 built-in wireless MAC, single chain
802.11b/g/n (911-2Hn) or 802.11a/g/n (911-5Hn)
Notes:
* Older versions of these boards might be equipped with a NAND
flash chip instead of the SPI NOR device. Those boards are not
supported (yet).
* The MikroTik RB911-5HnD (911 Lite5 Dual) board also uses the
same hardware. Support for that can be added later with little
effort probably.
Installation:
1. Setup a DHCP/BOOTP Server with the following parameters:
* DHCP-Option 66 (TFTP server name): pointing to a local TFTP
server within the same subnet of the DHCP range
* DHCP-Option 67 (Bootfile-Name): matching the initramfs filename
of the to be booted image. The usable intramfs files are:
- openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
- openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf
- openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin
2. Press the reset button on the board and keep that pressed.
3. Connect the board to your local network via its ethernet port.
4. Release the button after the LEDs on the board are turned off.
Now the board should load and start the initramfs image from
the TFTP server.
5. Upload the sysupgrade image to the board with scp:
$ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin
5. Log in to the running system listening on 192.168.1.1 via ssh
as root (without password):
$ ssh root@192.168.1.1
7. Flash the uploaded firmware file from the ssh session via the
sysupgrade command:
root@OpenWrt:~# sysupgrade /tmp/fw.bin
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Add patches for the leds-gpio driver to make it usable with
open-drain and open-source kind of GPIO lines.
This type of functionality is required by various MikroTik boards.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Modify the rbspi_platform_setup() function to return the pointer of the
rb_info structure. This allows board specific setup routines to access
the various fields of the information. It is useful for investigating
the hardware option bits for example.
Also update the board setup codes, to ensure that those handle the new
return value correctly.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Add bit definitions for the 'hardware options' tag which is used in
the MikroTik devices' hardware configurations. These values can be
used in board setup codes, to do different initialization sequences.
The values were obtained from the RouterOS 6.41-rc38 patches.
Additionally, introduce two helper functions what make the processing
of the hardware options easy.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Support for Winbond NAND flash detection was added into the generic
patches and this conflicted with this patch adding Gigadevice support.
Fixes: 02050f7e7d ("kernel/4.{4, 9}: add manufacturer ID for Winbond NANDs")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some part of this patch was added to the generic patches as it was
needed also for some other target. Do not add it here any more.
Fixes: 02050f7e7d ("kernel/4.{4, 9}: add manufacturer ID for Winbond NANDs")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds support for the new configuration option CONFIG_RETPOLINE and
refreshes the configuration.
Fixes: d8565a06dc ("kernel: bump 4.9 to 4.9.77")
Fixes: 9ddfac8015 ("kernel: bump 4.14 to 4.14.14")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This replaces the current patches used to make the kernel headers
compatible with musl with the version which was accepted upstream. This
is included in upstream kernel 4.15.
This was compile tested with iproute2 build on all supported kernel
versions with musl and one one with glibc.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
nftables 0.8.1 generates some new commands which will not work without
this on big endian systems. This patch is included in Linux 4.11 and
later.
My rule matching a TCP port was not working:
nft add rule ip foo bar ct state new tcp dport 22 accept
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The patch 0022-dts-ipq4019-support-ARMv7-PMU.patch
was merged into 4.8-rc1.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[refresh patches]
Signed-off-by: Mathias Kresin <dev@kresin.me>
During the integration of the ipq40xx target,
the phy drivers were included into the ipq806x's
target kernel config.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch renames the AVM FRITZ!Box 4040's board-2.bin
file and package to match the 'vendor_product' format.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch aligns the device-tree file with the latest
guidelines.
- No longer include qcom-ipq4019-ap.dk01.1.dtsi. This
file is only partially upstream and therefore subjected
to changes that might not be compatible with the board.
As a result, the definitions from the file have been
copied into this dts.
- exclusively use decimal GPIO addresses.
- reorganize the reserved-memory layout to waste less
memory. There's no point in keeping the u-boot loader
around. This should also make it possible to create
an image that will boot with the original EVA/ADAM2 loader
without needing to install the modified u-boot loader.
And finally mark the "tz-apps" as reusable.
There isn't a way to upload apps to the trust-zone in OpenWrt
yet. But it might see some use in the future as a "secure"
key-store/TPM.
- sort the first-level nodes alphabetically.
- sort nodes with an address by the address.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
According to console log during TP-Link TL-WR840N v5 OEM firmware update
procedure 0x3e0000-0x3f0000 64kB "config" partition, which is used to store
router's configuration settings, is erased and recreated again during every
OEM firmware update procedure, thus does not contain any valuable factory data.
So it is conviniant to use this extra 64kB erase block for jffs overlay due
limited flash size on this device like it used on TP-Link's ar71xx boards.
Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
The platform_check_image() stub need to return 0 for success, otherwise
the sysupgrade will fail with:
Image check 'platform_check_image' failed.
Fixes: aa6f5f1787 ("kirkwood: use image metadata")
Signed-off-by: 尤晓杰 <yxj790222@163.com>
[reworded commit message}
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the first found directory in the tar archive instead of relying on
a directory named according to the userspace boardname.
It allows to change the boardname without adding another compatibility
layer to the zyxel sysupgrade.
Fixes: 33f09cf151 ("ipq806x: convert to dt-based board-detection")
Signed-off-by: Mathias Kresin <dev@kresin.me>
The setup code of the OpenMesh OM5P ACv2 device uses nothing
from the mdio-gpio.h header, so remove the inclusion of that.
Also remove the kernel version check which is needed only
because the mdio-gpio.h header exists in a different path
in older kernels.
Compile tested only.
Cc: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Commit e15c63a375 ("ar71xx: add support for MikroTik RouterBOARD wAP
G-5HacT2HnD (wAP AC") broke the format of the patches. In unified diff
format, the unchanged, contextual lines must be preceded by a space
character.
Refresh the patches with quilt to fix them.
Fixes: e15c63a375 ("ar71xx: add support for MikroTik RouterBOARD wAPG-5HacT2HnD (wAP AC")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The patches introduced in commit 20e68f6d39 ("ar71xx: kernel: enable
PCI on QCA9556 SoC") have non standard format. In unified diff format,
the unchanged, contextual lines must be preceded by a space character.
Refresh the patches with quilt to fix them.
Fixes: 20e68f6d39 ("ar71xx: kernel: enable PCI on QCA9556 SoC")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The setup code defines four individual structures for the
Reset buttons of the supported boards. The only difference
between the definitions is the GPIO number used for the
button.
Replace the different structures with one generic variant,
and add a helper function to simplify the button registration.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The Gateworks GW5520 board uses 2x intel gigabit mac's, instead of the
internal i.MX6 FEC.
Add support for these.
Signed-off-by: Scott V. Kamp <outbackdingo@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Picking commit from QSDK
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=eggplant&id=a86bda9f8a7965f0cedd347a9c04800eb9f41ea3
Commit message:
"During removal of the glue layer(dwc3-of-simple), USB master reset is set to active and during insertion it is de-activated."
Change-Id: I537dc810f6cb2a46664ee674840145066432b957
Signed-off-by: Vasudevan Murugesan <vmuruges@codeaurora.org>
(cherry picked from commit 4611e13580a216812f85f0801b95442d02eeb836)"
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
A newer clk and cpufreq drivers for ipq806x platform had been sent upstream.
A change that i have noticed is that now it's possible to set min, cur and max frequencies from sysfs (previously it was bugged and caused nothing).
Following patches are removed:
- 0036-clk-Avoid-sending-high-rates-to-downstream-clocks-du.patch - seems it was dropped from the patchset by current committer.
- 0044-clk-qcom-krait-Remove-CLK_IS_ROOT.patch - already applied to the driver itself in the corresponding patch.
- 0057-clk-qcom-Add-regmap-mux-div-clocks-support.patch - seem to be irrelevant to ipq806x.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
According to QSDK and OEM tarballs (checked c2600, r7500v2, r7800) 2nd pci slot (pci1, 2,4 GHz card)) on ap148 based boards should operate in gen1 mode.
EA8500 is an exception and according to GPL pcie0 should operate in gen1 mode.
In previous commit we've added the support for this option, so enable it in DT for affected devices.
QSDK ref:
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=f3b07fe309027c52fc163149500cedddd707c506
While at it move the phy transmit termination offset value into dtsi file as it's platform specific.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
In current state there's huge regression on ipq806x target that causes the device to transmit broken/malformed frames that are not corrected/detected by error control mechanisms and other less severe issues.
https://bugs.lede-project.org/index.php?do=details&task_id=1197
This finally had been narrowed down to patch 0071-pcie-qcom-fixes.patch
Meanwhile QSDK contains a handful of commits that add support for ipq806x to upstream qcom pcie driver
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/log/drivers/pci/host/pcie-qcom.c?h=eggplant
Unfortunately qca developers do not bother to push it upstream.
Using those commits instead of lede 0071 patch fixes mentioned issue and probably many others as it seems that corrupted data has been originating within pcie misconfiguration.
Fixes: FS#1197 and probably others
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The blue LED is what other firmwares use for this device, and it's a lot
easier on the eyes than its shade of yellow, which implies an error
condition.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[merge into existing $boardname:blue:status block]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
Acked-by: Cezary Jackiewicz <cezary@eko.one.pl>
TP-Link Archer C20 v4 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN.
Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 3x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power input switch
* WAN LED in this devices is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
* MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't
work.
Flash instruction:
The only way to flash LEDE image in ArcherC20v4 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt7628-ArcherC20v4-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
This changes device name from "TP-Link Archer C20" to "TP-Link Archer C20 v1"
because of TPLINK released new TP-Link Archer C20 v4. Additionally
migration to the generic board detection has been made.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Match mapping of the switch LEDs according to the TP-Link
firmware behavior. LAN port 1 triggers the most right LAN LED,
LAN port 2 the second LAN LED from the right and so on.
Signed-off-by: David Bauer <mail@david-bauer.net>
As long as we can't enforce image metadata, we need to use (platform)
image checks to have at least soem kind of validation.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Ubifs is disabled for all boards except the evaluation boards and the
Fritz!Box 4040 anyway. According the author, the ubifs support for the
Fritz!Box 4040 wasn't enabled on purpose.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Remove leftover code used for legacy images. There are no relevant
binary differences for the images after removing the legacy leftovers.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Initialise the filesystem specific build command. Otherwise it will be
unintended inherit to following images and will cause a wrong image
format.
The issue is around for ages but was only recently triggered due to the
added support for the Openmesh a42.
Fixes: FS#1276
Signed-off-by: Mathias Kresin <dev@kresin.me>
Current EnGenius ENS202EXT factory image recipe version causes factory
images of the following devices to be corrupted. This issue wasn't
visible until recent changes of image Makefile snippets order.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Remove leftover reference to a not existing kmod-usb-musb-tusb6010 from
the omap24xx target, the corresponding module is built into the kernel.
Fixes: 96815fe0a2 ("kernel: remove omap24xx specific kernel module packages")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This patch adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD (wAP
AC), a small weatherproof dual band, dual-radio 802.11ac wireless AP with
integrated omnidirectional anntennae and one 10/100/1000 Mbps Ethernet
ports.
See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9556
- RAM: 64 MB
- Storage: 16 MB NOR
- Wireless:
· Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae
· Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae
- Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port, passive
PoE in
Working:
- Board/system detection
- Sysupgrade
- Serial console
- Ethernet
- 2.4 GHz radio
- 5 GHz radio
- Reset button
Not working:
- LEDs (added according to Mikrotik's GPL sources but not functional)
Unsupported:
- ZT2046Q SPI temperature and voltage sensor
Contributors: Giuseppe Tipaldi (@Ciusss89)
Ricky (@rickydee)
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: whitespace fix, use PHYADDR instead of PHYMASK]
This patch enables the PCI bus on the QCA9556 SoC, the same way it is
done on the same family SoC QCA9558.
Tested on a MikroTik RouterBoard wAPG-5HacT2HnD (wAP AC).
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
ALFA Network AC1200RM is an AC1200 router, with 5-port FE switch and
USB 2.0 port. Device is based on MediaTek MT7620A + MT7612EN.
Specification:
- MT7620A (580 MHz)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 5x 10/100 Mbps Ethernet with passive PoE output in WAN and LAN4
- 2T2R 2.4 GHz (MT7620A)
- 2T2R 5 GHz (MT7612EN)
- 1x USB 2.0
- 9x LED (8 driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12-24 V)
- 2x UART, I2C, I2S and LED headers
Flash instruction (do it under U-Boot, using UART and TFTP server):
Select option "2: Load system code then write to Flash via TFTP" and
use "sysupgrade" image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
GL.iNet GL-AR750 is a small size, dual-band (AC750) router, based on
Qualcomm/Atheros QCA9531 v2 + QCA9887. FCC ID: 2AFIW-AR750.
Specification:
- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3x 10/100 Mbps Ethernet
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 1x USB 2.0 (power controlled by GPIO)
- 1x microSD (GL857L)
- 3x LED (all driven by GPIO)
- 1x button (reset)
- 1x 2-pos switch
- header for optional PoE module
- 1x micro USB for main power input
- UART + I2C header on PCB
Flash instruction:
Vendor firmware is based on OpenWrt/LEDE. GUI or sysupgrade can be used
to flash OpenWrt/LEDE firmware.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network R36A is a successor of the previous model, the R36 (Ralink
RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2.
Specification:
- 650/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R (QCA9531) 2.4 GHz, 2x u.fl connectors on PCB
- 1x USB 2.0 (power controlled by GPIO)
- 6x LED (5 of them are driven by GPIO)
- 2x button (reset, wifi/wps)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- DC jack for main power input (12 V)
- UART header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Teltonika RUT900 is an industrial 3G router based on Atheros AR9344.
There are available 3 other models in RUT9xx series: RUT905, RUT950 and
RUT955, which differ in availability of additional I/O ports, built-in
GSM modem type, GPS antenna and other features. FCC ID of the RUT950
model (LTE module built-in): 2AET4-RUT950.
This patch adds support for the RUT900 model only but can be easily
extended to cover whole series. Also, as there are several different
3/4G modules (Huawei, Quectel, Telit) used in whole series, packages
required for WWAN support are not included by default. It is up to the
user to install required software for built-in modem.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344), with ext. PA (MGA-22103) and LNA
- built-in 3G module (example: Telit HE910-D)
- 2x miniSIM slot
- 2x RP-SMA/F (Wi-Fi), 2x SMA/F (3G)
- PCA9539 16-bit GPIO I2C expander
- 12x LED (4 are driven by AR9344, 7 by PCA9539)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- UART available on PCB edge connector
Serial console pinout:
- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side
Flash instruction:
Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.03.960" firmware and U-Boot "3.0.1".
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network N5Q is a successor of previous model, the N5 (outdoor
CPE/AP, based on Atheros AR7240 + AR9280). New version is based on
Atheros AR9344.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 5 GHz (AR9344), with ext. PA (RFPA5542) and LNA, up to 27 dBm
- 8x LED (7 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmare which is based
on OpenWrt/LEDE. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network AP91-5G is a 5 GHz outdoor AP/CPE board, based on Atheros
AR7240 + AR9280.
Specification:
- 400/400/200 MHz (CPU/DDR/AHB)
- 32 MB of RAM (DDR1)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 1T1R 5 GHz (AR9280), with ext. PA (SE5004L) and LNA, up to 27 dBm
- 6x LED (5 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART and LEDs headers on PCB
Flash instruction:
Use "factory" image in vendor GUI (in case of problems, make sure your
board has up to date firmware). Alternatively, TFTP in U-Boot can be
used: select option "2. Load system code then write to Flash via TFTP"
during early boot and use "sysupgrade" image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The KEXEC_FILE symbol exists for X86 since kernel 3.17, and since 4.10
for PPC64. Add it to x86/config-4.9 and to generic/config-4.14.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Several new DRM symbols that were introduced after 4.9 are missing in
the generic config for 4.14, so add them.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
While working on a new target (meson), the kernel build failed due to
missing DRM_DEBUG_MM_SELFTEST symbol. This can potentially happen on all
targets that enable DRM drivers in the kernel config or via kmod
packages, so add it to the generic config and remove it from x86
subtarget configs, together with DRM_DEBUG_MM.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This new subtarget sets the small_flash flag and removes unused kernel
configuration.
small_flash removes KERNEL_KALLSYMS, which saves ~107KB in the default
configuration; removing unneeded hardware support from ar71xx/tiny saves
another ~18KB (both after LZMA).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Rather than including all machines for the generic subtarget in the base
configuration, leave the base configuration without specific machines and
create a proper subtarget config for ar71xx/generic. The configuration
diffs of the mikrotik and nand subtargets get significantly shorter, as
will the configurations of future subtargets.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
While we'd like to convert ar71xx to DT-based configuration
eventually, we aren't quite there yet, and shipping half-baked DT support
that is not used at all wastes precious space.
Saves ~120KB before LZMA, ~33KB after LZMA.
Run-tested on TP-Link CPE510 and TL-WR841 v7.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Disable CONFIG_PROC_PAGE_MONITOR in most places and only keep it enabled
for virtual targets such as malta or potent ones like x86.
This saves up to 4KB of uncompressed kernel size and significantly
decreases CPU load under certain workloads.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* QCA IPQ401x
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
* powered only via POE
- 802.3af POE on Ethernet 1
- 18-24v passive POE (mode B) on Ethernet 2
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The kernel driver gpio-wdt or the userspace tool om-watchdog can be used to
trigger external gpio watchdog chips. The gpio-wdt driver has the benefit
that it can be configured together with the rest of the device in the DTS
and better integrates in the OpenWrt via procd.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Use the generic board detection method:
- Board name: First compatible string from the device tree
- Board model: Model property from the device tree
Change occurrences of board name in userspace by the compatible
string, and removed target specific board detection script
Replace the definition of SUPPORTED_DEVICES in Device/Default
to extract the dt compatible string from each device definition.
Additionally, for devices supported by lede-17.01, append
the value of BOARD_NAME to SUPPORTED_DEVICES in the device
definition.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Use <manufacturer>_<modelname> as image name for board using the
devicetree compat string as boardname.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
This will allow to maintain the current syntax for LEDs config
when switching to a device tree compatible string boardname.
None of the current boards use a comma in the boardname, so they
will be unaffected.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
There are only artifacts for these boards in our tree and not even
partial support.
Drop teh stale files.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The 4.14 kernel configuration defaulted to a v4/v5 multiplatform while
4.9 was using a v6/v7 default configuration. Resync 4.14 against 4.9 so
they are nearly identical.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a bunch of missing configuration symbols found while building
armvirt for 4.14 after re-synchronization of the configuration between
4.9 and 4.14.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch updates the apm821xx target to use the 4.14 kernel.
4.14 finally ships with a driver for the WNDR4700's tc654 fan
controller. The custom driver is deprecated in favor of the
upstream driver and the thermal cooling definitions in the DTS
are updated.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Without this patch one sdcard image with the following name is created
for all devices:
openwrt-at91-sama5--sdcard.img.gz
This makes the build system create device specific versions like:
openwrt-at91-sama5-at91-sama5d2_xplained-sdcard.img.gz
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This solution is more upstream compatible as it only requires specifying
of_match_table in the parser code and doesn't depend on linux,part-probe
which is solution made generic by a LEDE downstream patch that can't be
upstreamed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This backports upstream support for "compatible" DT property set for the
"partitions" subnode of flash node. It allows specifying how partitions
should be created/parsed. Right now only "fixed-partitions" is
supported.
It should eventually replace our downstream "linux,part-probe" solution.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Multicast routing support is not needed in most setups, and increases the
size of the kernel considerably (>10K after LZMA). Add a config switch to
allow disabling it.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The underlying issue breaking Spansion flash has been fixed with "mtd: spi-nor:
wait until lock/unlock operations are ready" and "mtd: spi-nor: wait for SR_WIP
to clear on initial unlock", so we can support unlocking for Winbond flash
again.
This is necessary to have writable flash on certain UBNT devices with some
bootloader versions.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Renaming an atm etherbride using 'ip link' (via hotplug) is racy since the
original netdev might disappear before br2684ctl has finished appling it's
setting:
local2.notice br2684ctl[1667]: Interface "nas0" created sucessfully
local2.notice br2684ctl[1667]: Communicating over ATM 0.8.35, encapsulation: LLC
kern.info kernel: dsl0: renamed from nas0
kern.err kernel: br2684:br2684_regvcc: tried to attach to non-existent device
local2.err br2684ctl[1667]: Could not configure interface:No such device or address
By passing the final used netdev name to br2684ctl_wrap another race
condition workaround will be enabled again.
Change the lantiq ptm driver to create a netdev with the name dsl as well.
Albeit the rename via 'ip link' works fine so far, using a different
approach for ptm then atm could be confusing.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Enable CONFIG_VFP again which was disabled during the 4.9 -> 4.14 bump.
Boot tested both 32 and 64 bit subtargets using initramfs images with the
qemu-system-arm and qemu-system-aarch64 emulators.
Fixes: aa100b66f2 ("armvirt: bump to v4.14")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
also known as
POGO-V4-A3-02
or
POGO-V4-A3-01
SoC: Marvell 88F6192 800Mhz
SDRAM memory: 128MB
Gigabit ethernet: 1 Marvell 88E1310
Flash memory: 128MB
2 status LEDs (one green one red)
1 "Eject" button on the back (used as "Reset" button)
1 USB 2.0 port (on upper side)
1 sata slot (power + data) for 2.5'' drives (upper side)
2 USB 3.0 ports from a controller on PCIe x1 of the SoC
1 full-size SDcard slot (fits a whole SD card into it)
This device supports the (linux-only) kwboot tool to send
a new uboot over serial console, so it is easy to unbrick
in case the uboot is erased and the device won't boot.
-----
Install instructions:
-----
Since it's not possible to get ssh access to these
devices, the only way to take control is to
solder pins to get TTL serial access.
Case can be opened by removing screws beneath two rubber
feet at back of device, then lifting while prying the
sides of the upper part out to unhook a latch on each
side about 2/3rds of the way toward the front.
Serial connection pins are those labeled "J11", left
of SD as you face SD opening.
Pins are (from left to right, i.e. the first in the list
is the nearest to the SD slot) GND, Rx, Tx.
Do not connect +V pin if you use a USB (self-powered)
TTL-to-USB dongle. Any USB TTL-to-USB converter will work.
Baud rate is 115200, parity "none", databits "8",
flow control "none".
Stock uboot is unable to read ubi partitions (nor usb)
so we will replace it first with our uboot.
Start a TFTP server at IP address 169.254.254.254, and
place the uboot.kwb file in the folder of the server.
Start the serial session and then power up the device.
As soon as you see text on the serial start pressing random
letter keys to stop the boot process.
If you see something like the following line you can proceed:
CE>>
Otherwise if text is still scrolling by you missed the
opportunity, pull the plug and try again.
write
printenv ethaddr
The uboot will write something like this:
ethaddr=00:50:43:00:02:02
This is the device's MAC address, also present in the sticker
under the device.
Write this down as we will need to add it in the
new uboot configuration.
Use the following commands to load the new uboot:
tftp 0x20000 u-boot.kwb
If the uboot confirms that the transfer was successful,
then you can write it to flash with the following commands:
nand erase 0 0x200000
nand write 0x20000 0 0x1c0000
if after the last command the uboot wrote
"xxxx bytes written: OK"
then it was written correctly and we can proceed.
If it did not go well, try again or ask assistence in forums.
Shutting down or rebooting at this time will brick
the device, to unbrick it you will need to use the kwboot
tool from a Linux PC or Virtual Machine.
Now write:
reset
and press enter, the device will reboot and you should see
again text scrolling by.
Press a random key to stop it, and now you should see
pogoplugv4>
We now add the MAC address back, write:
setenv ethaddr '00:50:43:00:02:02'
Confirm that the uboot has understood by writing
printenv ethaddr
If all looks ok, save the setting with
saveenv
At this point the uboot is configured, and we only need to load
the firmware in the flash memory.
Follow the steps below in "Firmware recovery procedure".
----
Firmware recovery procedure
----
The new uboot allows easy recovery from a bad firmware upgrade
where you can't access the device anymore over ssh or luci.
Take a USB flash drive formatted as FAT32, and copy the
initramfs image file in it (it will have "initramfs" in the
file name), then rename it as "initramfs.bin".
Insert the USB drive in the USB 2.0 port of the pogoplug
(the port at the top).
Power up the device, and wait for it to finish booting.
The uboot should find and load the "initramfs.bin"
from usb and if you are connected with serial you should
see the linux kernel boot log (text scrolling by).
Once it is done, press Enter and you will be greeted by
the OpenWRT banner.
If you were not connected with serial just wait a bit and,
you will be able to access it with ssh or luci web interface
(once you find its IP).
The recovery "initramfs" images are run from RAM, so you will
have to do a normal sysupgrade (firmware upgrade) to write
a firmware image to flash memory.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Use <manufacturer>_<modelname> as image name.
Use the BOARD_NAME variable to ensure that the former used boardname is
still used as the subdirectory name for the sysupgrade-tar image, to
not break sysupgrade from earlier versions.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Append and enforce image metadata. Remove the device specific image
checks, they are replaced by image metadata.
Signed-off-by: Mathias Kresin <dev@kresin.me>
There is no point in being that specifc in a generic dts covering a range
of boards. Keep only the the generic compat string to use it for a
devicetree based boardname.
Signed-off-by: Mathias Kresin <dev@kresin.me>
No image build code for the Guruplug, Sheevaplug and NSA310S exists. Drop
support for the boards for now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Drop NAND_BLOCKSIZE, UBI_OPTS and UBIFS_OPTS. They are either used by
not supported filesystems or by the legacy image build code.
Add common used options/images to the default build code and override
the options where necessary.
Don't export the kernel image, it isn't required by any board.
While at it, change the file extension for the sysupgrade images to bin.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The TP-Link firmware uses (primary_mac-1) as MAC-address
for the 5GHz WiFi. This applies the same behaviour to LEDE.
Currently, the MAC-address is retrieved from eth1, which
does not exist on the Archer C7 v4. As a result from this,
every C7 v4 with LEDE carries the same MAC-Address on the 5GHz WiFi.
Signed-off-by: David Bauer <mail@david-bauer.net>
There are 3 ethernet ports on Y1. LAN1 on port1, LAN2 on port0 and WAN on
port4.
Use a standalone switch configuration to match this and use the switch
trigger so that LAN LED could indicate the connetction status for both
lan ports correctly.
This patch also drop the internet led configuration, because there is a
WAN led for port4 and eth0.2 isn't always used as WAN.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 4.4.0 is always
false. Remove the obsolete check from mach-rb4xx.c to clean up the code
a bit.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 4.2.0 is always
false. Remove the obsolete check from ag71xx_main.c to clean up the code
a bit.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 3.15.0 is always
false. Remove the obsolete checks from the target specific source files
to clean up the code a bit.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Disable the drivers for the following ethernet switches:
Realtek RTL8306
Realtek RTL8366/8367
Marvell 88E6060 (DSA)
Marvell 88E6063 (DSA)
Also disable the phy driver for Marvell PHYs.
None of the supported RouterBOARDs are using any device
which needs these drivers.
Disable the DSA framework too, because it is not required
by the remaining switch drivers.
This reduces the compressed kernel size by ~20KB.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The Marvell 88E6063 ethernet switch driver depends on the DSA
framework. Add a 'depends on NET_DSA' statement to its Kconfig
entry to state that explicitly.
Fixes the following Kconfig warning:
warning: (NET_DSA_MV88E6060 && NET_DSA_MV88E6063) selects NET_DSA_TAG_TRAILER which has unmet direct dependencies (NET && NET_DSA)
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Building Linux 4.4 for ar71xx throws the following warnings in
drivers/net/phy/mdio-bitbang.c:
CC drivers/net/phy/mdio-bitbang.o
In file included from include/linux/irqflags.h:14:0,
from drivers/net/phy/mdio-bitbang.c:20:
drivers/net/phy/mdio-bitbang.c: In function 'mdiobb_read':
include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
(void)(&__dummy == &__dummy2); \
^
include/linux/irqflags.h:63:3: note: in expansion of macro 'typecheck'
typecheck(unsigned long, flags); \
^
include/linux/irqflags.h:124:3: note: in expansion of macro 'raw_local_irq_save'
raw_local_irq_save(flags); \
^
drivers/net/phy/mdio-bitbang.c:162:2: note: in expansion of macro 'local_irq_save'
local_irq_save(flags);
^
include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
(void)(&__dummy == &__dummy2); \
^
include/linux/irqflags.h:68:3: note: in expansion of macro 'typecheck'
typecheck(unsigned long, flags); \
^
include/linux/irqflags.h:126:39: note: in expansion of macro 'raw_local_irq_restore'
#define local_irq_restore(flags) do { raw_local_irq_restore(flags); } while (0)
^
drivers/net/phy/mdio-bitbang.c:175:2: note: in expansion of macro 'local_irq_restore'
local_irq_restore(flags);
^
drivers/net/phy/mdio-bitbang.c:159:11: warning: unused variable 'i' [-Wunused-variable]
int ret, i;
^
In file included from include/linux/irqflags.h:14:0,
from drivers/net/phy/mdio-bitbang.c:20:
drivers/net/phy/mdio-bitbang.c: In function 'mdiobb_write':
include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
(void)(&__dummy == &__dummy2); \
^
include/linux/irqflags.h:63:3: note: in expansion of macro 'typecheck'
typecheck(unsigned long, flags); \
^
include/linux/irqflags.h:124:3: note: in expansion of macro 'raw_local_irq_save'
raw_local_irq_save(flags); \
^
drivers/net/phy/mdio-bitbang.c:185:2: note: in expansion of macro 'local_irq_save'
local_irq_save(flags);
^
include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
(void)(&__dummy == &__dummy2); \
^
include/linux/irqflags.h:68:3: note: in expansion of macro 'typecheck'
typecheck(unsigned long, flags); \
^
include/linux/irqflags.h:126:39: note: in expansion of macro 'raw_local_irq_restore'
#define local_irq_restore(flags) do { raw_local_irq_restore(flags); } while (0)
^
drivers/net/phy/mdio-bitbang.c:200:2: note: in expansion of macro 'local_irq_restore'
local_irq_restore(flags);
^
These are caused by the 900-mdio_bitbang_ignore_ta_value and
901-phy-mdio-bitbang-prevent-rescheduling-during-command patches.
The first patch removes some code but it does not remove the variable
which is used by the removed code only.
The second patch adds local_irq_{save,restore} calls. The type of the
argument of these calls must be 'unsigned long', but the patch defines
the variable as 'long'.
Fix both patches to silence the warnings.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The Annex A and Annex B version are using the same (old) userspace
boardname. Update the SUPPORTED_DEVICES to allow an update from lede-17.01.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Supermicro puts "Super Server" into their product_name DMI value
for a whole slew of products, making this value about as useful
as not having been filled in at all. Instead, fall back on the
board_name instead.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
There might be other places (such as vendor-supplied preinit scripts)
where we wish to take a DMI name and clean it up in a consistent way,
so make the sed command into a function.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Rename unwinder config symbols to match upstream changes.
Refresh patches.
Update patch that no longer applies: 202-reduce_module_size.patch
Also enable CONFIG_PAGE_TABLE_ISOLATION. This feature was backported
from 4.15 to the 4.14 stable series. It is enabled by default, so enable
it in OpenWrt as well.
Compile-tested on x86/64.
Runtime-tested on x86/64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
While bumping 4.14, the kernel build failed due to missing CONFIG_KASAN
symbol. Move it to generic config instead of defining it for all arm64
and x86/64 targets.
It was only added in 4.0, so not needed in config-3.18.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The CPU sub type was set to a CPU version with FPU, but the FPU feature
was not activated before, so a soft float toolchain was created.
Activate also the FPU feature to create the correct toolchain.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This activates neon and VFPv4 support for this target. The CPU support
these feature so also use them.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since BusyBox 1.25.0 dd command supports iflag=skip_bytes which allows
skipping requested amount of bytes without reducing blocksize. Thanks to
this we can leave default blocksize and let dd work more efficiently.
On Netgear R6250 "dd skip=58 iflag=skip_bytes" can be 5 times faster
than "dd bs=58 skip=1" when extracting TRX out of CHK.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's a device based on BCM5365P (0x5365 package 0x00). This SoC has
USB 1.1 controller but device has two USB 2.0 parts. They are handled by
PCI-based controllers: 1106:3038 UHCI and 1106:3104 EHCI.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This was broken in 7bab49fd ("lantiq: add compatible strings to dts
files"), causing for the dm200 garbled serial output during boot, and
likely other issues.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
[fix the compat string of the P2601HNFX as well]
Signed-off-by: Mathias Kresin <dev@kresin.me>
That patch fixes handling SPI messages with two writing transfers. It's
important when using e.g. by m25p80 driver which uses one transfer for
opcode and another one for data.
Thanks to that fix we can now drop m25p80 workaround patch. It means one
less hack and also a better flash writing performance as there is no
more data buf copying.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
A lot of 1U x86_64 servers have NVMe support, which is lower-power
and higher speed than SSD or CFast drives, etc. The drivers
required to make this work are trivial.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Remove a stray -Wp left in host_c_flags causing build failures for newer
4.14 versions.
Reported-by: Michael Marley <michael@michaelmarley.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Advantages:
- preserves existing partition layout on the sd-card.
Only the boot and rootfs partition will be overwritten.
Please note that sysupgrade will refuse to upgrade, if the existing
installation has an incompatible partition layout. Future changes
to the bootfs and/or rootfs partition size will likely cause breakage
to the sysupgrade procedure. In these cases, the ext4-sdcard.img.gz
will have to be written to the sdcard manually.
Please don't forget to backup your configuration in this case.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Use the values populated by the generic board detect function. The
first compatible from the device tree source file will be the board
name in userspace. The model property from the device tree source file
will be the model name.
Change the board name where used in the userspace and drop the target
specific board detect, to use the generic one.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds the compatible string for the various RPIs from
4.14 upstream.
Note: The 4.14 upstream does not include the compute modules.
If the CM* would just house the SoC, it could in theory use the
"raw" chip compatible string. However, these CM boards also come
with RAM and eMMC. So they have to have a proper comaptible.
For now, "raspberrypi,compute-module-{1|3}" will be good enough.
Note2: The original CM was renamed to CM1 when CM3 was released.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch converts all the raspberrypi images to utilize
the common metadata-based image verification.
Note: the CM1 and CM3 currently use the same "rpi-cm"
boardname.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Commit c312cef223 ("ar71xx: spi-rb4xx fix.") replaced the clk_enable() call
with clk_prepare_enable() to meet the common clock framework requirements.
However it did not change the clk_disable() call in the error patch which
thus leads to imbalance.
Fix the code by using the correct counterpart of clk_prepare_enable() in both
places.
Fixes: c312cef223 ("ar71xx: spi-rb4xx fix.")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
A few UBI messages lacks the trailing newline character which
leads to ugly lines in the bootlog like this:
[ 6.649159] UBI error: no valid UBI magic found inside mtd6[ 6.667751] Freeing unused kernel memory: 2196K
Add a newline character to the end of the messages to fix it.
After the fix the line from above looks better in the log:
[ 6.609182] UBI error: no valid UBI magic found inside mtd6
[ 6.627599] Freeing unused kernel memory: 2132K
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
A few UBI messages lacks the trailing newline character which
leads to ugly lines in the bootlog like this:
[ 6.649159] UBI error: no valid UBI magic found inside mtd6[ 6.667751] Freeing unused kernel memory: 2196K
Add a newline character to the end of the messages to fix it.
After the fix the line from above looks better in the log:
[ 6.609182] UBI error: no valid UBI magic found inside mtd6
[ 6.627599] Freeing unused kernel memory: 2132K
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
A few UBI messages lacks the trailing newline character which
leads to ugly lines in the bootlog like this:
[ 6.649159] UBI error: no valid UBI magic found inside mtd6[ 6.667751] Freeing unused kernel memory: 2196K
Add a newline character to the end of the messages to fix it.
After the fix the line from above looks better in the log:
[ 6.609182] UBI error: no valid UBI magic found inside mtd6
[ 6.627599] Freeing unused kernel memory: 2132K
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The value DSL_ChipSetHWVersion is fetched from the dsl frontend
via the dsl_control service, but not really provided by the dsl
frontend firmware and for now always "UNKNOWN".
The lantiq support told us that this information wouldn't be
provided in the foreseeable future, so let's remove this
useless "UNKNOWN" information.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Use a more appropriate compatible string. Fix the wireless led GPIO and
add the default wireless trigger. Use the wireless LED for boot state
indication as well.
Remove the GPIO pinmux for pins not exposed on the board.
Signed-off-by: Mathias Kresin <dev@kresin.me>
TP-Link TL-MR3420 v5 are simple N300 router with
5-port FE switch and non-detachable antennas.
Its very similar to TP-Link TL-WR841N V13.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- USB 2.0 Port
- UART (J1) header on PCB (115200 8n1)
- 8x LED, 2x button, power input switch
Flash instruction:
The only way to flash LEDE image in mr3420v5 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "lede-ramips-mt7628-tplink_tl-mr3420-v5-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
Move common tplink image build code into own recipe. Include the common
parts instead of including a full build recipe and overwriting former set
varaibles.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support for the MikroTik RouterBOARD 921GS-5HPacD r2
(mANTBox 15s), an outdoor sector antenna with a built-in 802.11ac
wireless router. Additionally, it adds a new profile for devices with
>= 128 MB NAND flash and 802.11ac to the ar71xx/mikrotik subtarget.
See https://mikrotik.com/product/RB921GS-5HPacD-15S for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9558 (720 MHz)
- RAM: 128 MB
- Storage: 128 MB NAND
- Wireless: external QCA9822 802.11a/ac 2x2:2
- Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE in
- SFP: 1x host
Working:
- Board/system detection
- NAND storage detection
- Wireless
- Ethernet
- 1x user LED
- Reset button
- Sysupgrade
Untested:
- SFP cage (probably not working)
Installation:
- Boot initramfs image via TFTP and then flash sysupgrade image
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Apply code from commits 9e1bc27e6d
(ar71xx: Fix UBIFS work on Mikrotik RB95x devices) and
665bb27499 (ar71xx: fix invalid pointer
dereference in rb95x_nand_scan_fixup()) to RB92x devices too.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This patch converts all apm821xx devices to the device-tree
board-detection method. All instances of the legacy
boardnames (mbl,mr24,...) are converted to "vendor,device"
identifier.
The custom board-detection code in apm821xx.sh is removed as
it no longer serves any purpose.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch enables metadata-supported image verification
for all apm821xx supported devices. Since this method comes
with a built-in image verification tool (fwtool), the previous
image checks can be removed.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Currently, the device name handle does not include the
manufacturer. This can make it hard do differentiate
between products from different vendors that have the
same product name. As the handle is used to derive
the image name.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch rename all the DT source files in order to
match upstream's "manufacturer-device.dts" format.
Please note that the DEVICE_DTB isn't changed. This is
because the u-boot of the MyBook Live defines the
fdt_file variable to be "apollo3g/apollo3g.dtb".
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Meraki choose to use their product's codename as the main
compatible string. Mathias Kresin commented that this is
a poor choice as this will confuse the users and devs once
the device-tree compatible is used for board-detection and
possible the image name.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch appends the "apm,bluestone" or "amcc,apollo3g"
machine compatible string to the current device tree source.
Please note that unlike other archs the PPC DT code does
not regard the machine's compatible string as a priority
list. This is explained in the kernel's usage-model.txt as follows:
"PowerPC uses a slightly different scheme where it calls the .probe()
hook from each machine_desc, and the first one returning TRUE is used.
However, this approach does not take into account the priority of the
compatible list, and probably should be avoided for new architecture
support."
For this reason, the "apm,bluestone" compatible string can't be
added to the WNDR4700. As otherwise the target specific pci
fix-up code will get ignored and this causes the ath9k WIFI
to not get initialized.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch sets the BOARD_NAME variable on each affected
apm821xx device. The existing DEVICE_PROFILE and
DEVICE_NAME assignments are deprecated as they no longer
serve any purpose.
The BOARD_NAME variable is used by the sysupgrade-tar
method to specifiy a directory overwrite for the
sysupgrade-$dir directory in the generated tar file.
Keeping the original boardname in this context will be
necessary for targets that utilize the sysupgrade-tar
method. Otherwise, sysupgrade on an previous installation
will not recognize the newly generated images.
This step is necessary since an upcoming patch realigns
the existing shortname for a device with a proper
"manufacturer_device" identifier.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The commit 87b668765e
("image: when using the new image build code, gzip ext4 images by default")
forced that all targets that select the ext4 as the root filesystem
to always compress the generated rootfs. This is fine, but this method
doesn't not allow to append the metadata on a per-target base.
Therefore this patch changes the rootfs image production rule to generate
the gzip step manually. This way the metadata can be appended at a later
date.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
"PandoraBox" is not the name of the manufacturer, it's a firmware made by
the manufacturer actually. Their official English name is "D-Team".
PBR-M1 is the only one they use "PandoraBox" as a brand name. Their other
products are using "Newifi" as their trademark (including Y1 and Y1S which
used to be OEM products for Lenovo).
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Previously Newifi D2 could only use PandoraBox M1's firmware.
It works fine, but LED GPIO is different.
As a result, a separated DTS file for this device should be implemented.
Hardware spec:
* CPU: MTK MT7621A
* RAM: 512MB
* ROM: 32MB SPI Flash
* WiFi: MTK MT7603+MT7612
* Button: 2 buttons (reset, wps)
* LED: 3 single-color LEDs (USB, WiFi 2.4GHz, WiFi 5GHz) &
2 dual-color LEDs (Power, Internet)
* Ethernet: 5 ports, 4 LAN + 1 WAN
Installation method:
Same as Newifi D1, users may need to request unlock code from the device
manufacturer. Otherwise, a SPI flash programmer may be necessary to get
the firmware flashed. After the device is unlocked, press and hold reset
button before power cable plugs in. Then go to http://192.168.1.1 to
upload and flash the firmware package.
Signed-off-by: Jackson Ming Hu <huming2207@gmail.com>
The VAR11N-300 is a tiny wireless-N device with a hardwired Ethernet
cable, one extra Ethernet port, and an internal antenna, based on the
MediaTek MT7620n chipset.
Specs:
- MT7620n WiSoC @ 600MHz
- 32 MB SDRAM
- 4 MB SPI flash
- 2T2R 2.4GHz WiFi-N
- 1 attached 10/100 Ethernet cable (LAN)
- 1 10/100 Ethernet port (WAN)
- 1 attached USB / barrel 5vdc power cable
- 5 LEDs (see notes below)
- 1 reset button
- 1 UART (3 pads on board)
Installation:
The stock firmware does not support uploading new firmware directly,
only checking the manufacturer's site for updates. This process may be
possible to spoof, but the update check uses some kind of homebrew
encryption that I didn't investigate. Instead, you can install via a
backdoor:
1. Set up a TFTP server to serve the firmware binary
(lede-ramips-mt7620-var11n-300-squashfs-sysupgrade.bin)
2. Factory reset the device by holding the reset button for a few
seconds.
3. Open the web interface (default IP: 192.168.253.254)
4. Log in with the "super admin" credentials: username `vonets`,
password `vonets26642519`.
5. On the "Operative Status" page, click the text "System Uptime", then
quickly click the uptime value.
6. If successful, an alert dialog will appear reading "Ated start", and
the device will now accept telnet connections. If the alert does not
appear, repeat step 5 until it works (the timing is a bit tricky).
7. Telnet to the device using credentials "admin / admin"
8. Retrieve the firmware binary from the tftp server: `tftp -l lede.bin
-r lede-ramips-mt7620-var11n-300-squashfs-sysupgrade.bin -g
<tftp-server-ip>`
9. Write the firmware to flash: `mtd_write write lede.bin /dev/mtd4`
10. Reboot
Tested:
- LAN / WAN ethernet
- WiFi
- LAN / WAN / status LED GPIOs (see notes below)
- Reset button
- Sysupgrade
Notes:
LEDs:
The board has 5 LEDs - two green LEDs for LAN / WAN activity, one blue
LED for WiFi, and a pair of "status" LEDs connected to the same GPIO
(the blue LED lights when the GPIO is low, and the green when it's
high). I was unable to determine how to operate the WiFi LED, as it
does not appear to be controlled by a GPIO directly.
Recovery:
The default U-boot installation will only boot from flash due to a
missing environment block. I generated a valid 4KB env block using
U-boot's `fw_setenv` tool and wrote it to flash at 0x30000 using an
external programmer. After this, it was possible to enter the U-boot
commandline interface and download a new image via TFTP (`tftpboot
81b00000 <image-filename>`), but while I could boot this image
sucessfully (`bootm`), writing it to flash (`cp.linux`) just corrupted
the flash chip. The sysupgrade file can be written to flash at 0x50000
using an external programmer.
Signed-off-by: Andrew Crawley <acrawley@gmail.com>
Add a helper variable which contains the boardname separated from the
vendor name. It allows to switch to a device tree compatible string
based boardname, by keeping the $board:colour:function syntax in
scripts handling/adding config for LEDs.
Boards not using the device tree compatible string as based boardname
are unaffected by the change, since none of them uses a comma in the
boardname.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use <manufacturer>_<modelname> as image name for board using the
devicetree compat string as boardname.
Replace the underline of the device define, to keep the SUPPORTED_DEVICES
in sync with a devicetree compat string based boardname.
Override the default SUPPORTED_DEVICES for board which are having an
userspace boardname with an underline.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The LinkIt Smart 7688/LinkIt Smart 7688 Duo are identical beside the
extra ATmega32U4 - accessible via UART - on the the Duo.
Since all relevant hardware is identical, drop the Duo special handling
in userspace.
Signed-off-by: Mathias Kresin <dev@kresin.me>
If we need to set the initial output value to GPIOF_OUT_INIT_HIGH (1) to
enable something, the pin is ACTIVE_HIGH. The same applies to
GPIOF_OUT_INIT_LOW (0) and ACTIVE_LOW.
Signed-off-by: Mathias Kresin <dev@kresin.me>
In the stock firmware both eth0 and eth1 are set to br-lan,
add this behavior to our images.
Fixes: FS#1084
Signed-off-by: Marty E. Plummer <hanetzer@protonmail.com>
The status led part was missed when changing the board name to *-nor.
Fixes: e12c72bb52 ("brcm63xx: Add Sercomm AD1018 support")
Reported-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Use <manufacturer>_<modelname> as image name.
Use the BOARD_NAME variable to ensure that the former used boardname is
still used as the subdirectory name for the sysupgrade-tar image, to
not break sysupgrade from earlier versions.
While at it, normalise the image filenames by using only lower case
characters and bin as file extension for sysupgrade images.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the first compatible string as board name in userspace. Add the new
board name as well as the former used board name to the image metadata
to keep compatibilty with already deployed installations.
Don't add the former used boardname for boards which exists only in
master or evaluation boards.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This adds basic support for kernel 4.14, this was tested in qemu only.
The subtarget configuration was refresh with kernel 4.14 and the
options needed to make it compile on kernel 4.9 were added manually.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel 4.14 kmod-bluetooth depends on kmod-crypto-ecdh, add
kmod-crypto-ecdh to LEDE.
Both packages also depend on the kmod-crypto-kpp package. To build this
we have to fix the dependency of CRYPTO_ECDH which has a typo.
This patch is already accepted upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds initial support for kernel 4.14 based on the patches for
kernel 4.9.
In the configuration I deactivated some of the new possible security
features like:
CONFIG_REFCOUNT_FULL
CONFIG_SLAB_FREELIST_HARDENED
CONFIG_SOFTLOCKUP_DETECTOR
CONFIG_WARN_ALL_UNSEEDED_RANDOM
And these overlay FS options are also deactivated:
CONFIG_OVERLAY_FS_INDEX
CONFIG_OVERLAY_FS_REDIRECT_DIR
I activated this:
CONFIG_FORTIFY_SOURCE
CONFIG_POSIX_TIMERS
CONFIG_SLAB_MERGE_DEFAULT
CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED
I am not sure if I did the porting correct for the following patches:
target/linux/generic/backport-4.14/020-backport_netfilter_rtcache.patch
target/linux/generic/hack-4.14/220-gc_sections.patch
target/linux/generic/hack-4.14/321-powerpc_crtsavres_prereq.patch
target/linux/generic/pending-4.14/305-mips_module_reloc.patch
target/linux/generic/pending-4.14/611-netfilter_match_bypass_default_table.patch
target/linux/generic/pending-4.14/680-NET-skip-GRO-for-foreign-MAC-addresses.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Just refresh the kernel configuration, some options are removed because
they are now in the generic kernel configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These are taken from the x86 target and should make support kernel 4.9
and 4.14 in the x86 target easier.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cover temperature sensors for all mainstream 64-bit processors, including
AMD 10h and 15h families, Intel iCore, Xeon, Atom, and Via Nano. Also
add CPUID support for user-space applications to detect CPU type.
Include the on-chip sensors for 64-bit CPU's in the generic profile
in case someone builds a 32-bit kernel to run on a Xeon SoC, etc.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Backport the mdio-bus reset gpio support from 4.12 and use it instead
of toggling the reset ourself.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Add support for the Sercomm AD1018 router
This a BCM6328 based board, 128 MB RAM, 128 MiB NAND flash,
with an onboard BCM43217 wifi, 4 ethernet ports and 1 USB
host port (not soldered). The board also has an FXS chip (Si32177)
connected via SPI (SS2#), without support in LEDE.
Since NAND flash chips aren't still supported in brcm63xx, the
support is for now added to work only with SPI flash chips. Therefore
hardware modding, soldering a new SPI flash chip, is required
to make the board work with LEDE (tested and working OK).
The flash at dts is intentionally left without partitioning to let
the user choose a NOR chip of any size (8, 16 or 32 MB).
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
[jonas.gorski: renamed ad1018 to ad1018-nor to signify the modification]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Since Linux 4.6, mtd->priv no longer points to the NAND specific
structure. Under 4.9 it contains NULL, thus using it to access
chip->options causes an invalid pointer dereference (FS#1200).
Update the code to use the mtd_to_nand() helper under 4.9 to obtain
the address of the chip specific data.
Fixes: 7bbf4117c6 ("ar71xx: Add kernel 4.9 support")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Since Linux 4.6, mtd->priv no longer points to the NAND specific
structure. Under 4.9 it contains NULL, thus using it to access
the fields of the nand_chip structure causes an invalid pointer
dereference.
Update the code to use the mtd_to_nand() helper under 4.9 to obtain
the address of the chip specific data.
Compile tested only.
Fixes: 7bbf4117c6 ("ar71xx: Add kernel 4.9 support")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Tested-by: Christian Lamparter <chunkeey@gmail.com>
When mtdsplit_minor.c is compiled under Linux 4.4, the compiler
drops the following warning:
CC drivers/mtd/mtdsplit/mtdsplit_minor.o
drivers/mtd/mtdsplit/mtdsplit_minor.c:106:14: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
.parse_fn = mtdsplit_parse_minor,
^
drivers/mtd/mtdsplit/mtdsplit_minor.c:106:14: note: (near initialization for 'mtdsplit_minor_parser.parse_fn')
The second parameter of the parser function must not have a 'const'
qualifier in 4.4. The 001-mtdsplit_backport.patch removes the qualifier
from other partition parsers. Update it to handle mtdsplit_minor.c as
well.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
This reverts commit 256990cbc0.
this commit caused a compile error
"TL_WR1043_V5_GPIO_LED_WANORANGE" is undefined.
Signed-off-by: John Crispin <john@phrozen.org>
Add missing definitions for the orange WAN LED on the TL-WR1043N(D) v4 and
v5. Minor format correction on a constant for consistency.
Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
This patch fixes the switch port numbering on Mikrotik RB951Ui-2nD (hAP).
Also fixes the switch port numbering shown on LuCI for Mikrotik RB493G.
Signed-off-by: João Chaínho <joaochainho@gmail.com>
Advantages:
- preserves existing partition layout. On the hard-drive.
Only the boot and rootfs partition will be overwritten.
Disadvantages:
- The upgrade process takes much longer to run.
from 2-3 seconds to 15-25 seconds.
Please note that sysupgrade will refuse to upgrade, if the existing
installation has an incompatible partition layout. Future changes
to the bootfs and/or rootfs partition size will likely cause breakage
to the sysupgrade procedure. In these cases, the ext4-rootfs.img.gz
has to be written manually onto the disk. Please don't forget to backup
your configuration in this cases.
Note2: This patch requires
"base-files: upgrade: make get_partitions() endian agnostic"
Note3: If your current installation does not host the two
changes, sysupgrading will wipe the existing partition
layout. Don't forget to backup your data!
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Please note that users with a Netgear WNDR4700
will need to update the device-tree partition
manually.
For instructions, please refere to commit 49856a4bb5
("apm821xx: make it possible to update the dtb partition on the WNDR4700")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Lantiq and IPQ806X (which includes IPQ40XX) both define the
same custom function {ipq806x|lantiq}_get_dt_led.
This patch moves the function into the base-file package at
lib/functions/leds.sh to make it more accessible for other
targets as well.
Cc: Mathias Kresin <dev@kresin.me>
Cc: John Crispin <john@phrozen.org>
Cc: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The bcm6368 pinctrl driver passed the wrong variable to
devm_regmap_field_alloc, causing it to blow up when later trying to
access the field.
Fixes#1211.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
For an unknown reason gcc tries to link in crti.o when building with a
glibc toolchain (this does not happen with other targets). Prevent this
by telling gcc explicitly to not do that.
Fixes the following build error:
/home/jonas/git/lede/staging_dir/toolchain-mips_24kc_gcc-5.5.0_glibc/lib/gcc/mips-openwrt-linux-gnu/5.5.0/../../../../mips-openwrt-linux-gnu/lib/crti.o: In function `_init':
(.init+0x18): relocation truncated to fit: R_MIPS_GOT16 against `__gmon_start__'
/home/jonas/git/lede/staging_dir/toolchain-mips_24kc_gcc-5.5.0_glibc/lib/gcc/mips-openwrt-linux-gnu/5.5.0/../../../../mips-openwrt-linux-gnu/lib/crti.o: In function `_init':
(.init+0x28): relocation truncated to fit: R_MIPS_CALL16 against `__gmon_start__'
collect2: error: ld returned 1 exit status
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This will avoid some conflicts when doing a git rebase or merge,
specially when adding support to a new device.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
[drop brcm47xx changes which rename the images]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Recent RouterBOOT version (at least version 3.41 on RB911G-5HPacD)
use "Board=" kernel parameter instead of "board=" to pass the board
name to the kernel. Due to this change the board detection code is
not working on the devices shipped with the new RouterBOOT version.
Because the kernel is unable to identify these boards they become
unusable despite that they are supported by the current code.
Update the prom_init code to convert the 'Board' kernel parameter to
'board'. After this change, the board detection works also with the
new RouterBOOT versions.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The target name does not need to included a revision
if all revisions are supported.
This target supports all revisions (v1, v2, v2.1).
Signed-off-by: Moritz Warning <moritzwarning@web.de>
[Keep the version numbers in the device title, it doesn't harm]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Remove the WW suffix, everything without a region suffix is world wide
anyway.
While at it, normalise the image filenames by using only lower case
characters.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Users are confused which image type they should use and there are more
drawbacks than adavantages in using a r/w ubifs rootfs in constrast to
a read-only squashfs rootfs like:
- less available free flash space due to better compression of squashfs
images
- no support for factory reset due to r/w filesystem
- possibility to break failsafe due to r/w filesystem
Therefore, drop support for r/w ubifs rootfs images.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The boardname isn't used any longer to find the subdirectory in the
sysupgrade tar archive, which makes this override useless.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Qualcomm claims this reduces cache misses. Original commit message below:
From: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Date: Tue, 11 Jun 2013 12:18:46 -0500
Subject: [ag71xx] reduce NAPI weight
In an attempt to increase our cache warmth, we are decreasing NAPI.
This increases the warmth of the reused SKBs.
Signed-off-by: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The motivation for this was misguided. It turns out tuning the NAPI weight could be useful for testing purposes. Therefore reverting.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This commit fixes LAN Port 1 not transferring data in case no
other LAN Port has active link-state on TP-Link Archer C58/C59.
Signed-off-by: David Bauer <mail@david-bauer.net>
This is a variant of the MT7620N-based Asus routers.
Specifications:
- MT7620N (580 MHz)
- 32 MB RAM
- 8 MB Flash
- 5x 10/100Mbps Ethernet (built-in switch)
- 2.4 GHz WLAN
- 2x external, non-detachable antennas
- UART (J2) header on PCB (115200 8n1)
Flash instructions:
1. Configure PC with static IP 192.168.1.75/24
2. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds. All 4 LEDs will
start to blink, which is when the router will accept firmware files via TFTP.
No known limitations on firmware filenames, just send it with a TFTP client
to 192.168.1.1.
3. Router will download file from server, write it to flash and reboot.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This allows people to build SDK from custom repository (git access using
ssh) and keep original URL in SDK's feeds.conf.default.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Jo-Philipp Wich <jo@mein.io>
This commit adds missing the GPIO key used as reset button.
Nexx WT1520 has a GPIO key for factory reset, but it's not defined in
WT1520.dtsi and cannot use it.
Drop the UART (full) from the device tree source file, it was never
used for this board. Adjust the kernel bootargs accordingly.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[add note about dropped UART (full) to the commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
There are multiple problems on the A64 SoC with the older drivers which
are fixed in the upstream kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens
Jonas Gorski
Stefan Lippers-Hollmann
Luis Araneda
Julien Dusser
George Hopkins
John Crispin
Karl Palsson
INAGAKI Hiroshi
Koen Vandeputte
Tim Harvey
Michael Heimpold
Rosen Penev
Yangbo Lu
Henryk Heisig
Matthias Schiffer
Sven Eckelmann
Ding Tengfei
David Bauer
Pawel Dembicki
Zoltan HERPAI
Arne Zachlod
Adrià Llaudet
Evgeniy Didin
Felix Fietkau
Stijn Tintel
Daniel Golle
Daniel Danzberger
Jo-Philipp Wich
Yousong Zhou
Catrinel Catrinescu
Jackson Ming Hu
Mathias Kresin
Hans Dedecker
Gabor Juhos
Kevin Darbyshire-Bryant
Christian Lamparter
Serg Studzinskii
尤晓杰
Pavel Kubelun
Daniel Gimpelevich
Maxim Anisimov
Chen Minqiang
Piotr Dymacz
Roger Pueyo Centelles
Davide Fioravanti
Sven Eckelmann
Florian Fainelli
Rafał Miłecki
Alberto Bursi
Chuanhong Guo
Philip Prindeville
Thomas Nixon
Vittorio Gambaletta
Martin Schiller
Tomasz Maciej Nowak
Andrew Crawley
Marty E. Plummer
Daniel Gonzalez Cabanelas
Sandeep Sheriker Mallikarjun
kyson Lok
Tim Thorpe
João Chaínho
Moritz Warning
Lucian Cristian