TP-Link Archer D7 v1 is a dual-band AC1750 router + modem.
The router section is based on Qualcomm/Atheros QCA9558 + QCA9880.
The "DSL" section is based on BCM6318 but it's currently not supported.
The Archer D7b seems to differ from the Archer D7 only in the
partition table.
Router section - Specification:
775/650/258 MHz (CPU/DDR/AHB)
128 MB of RAM (DDR2)
16 MB of FLASH (SPI NOR)
3T3R 2.4 GHz
3T3R 5 GHz
4x 10/100/1000 Mbps Ethernet
7x LED, 2x button
UART header on PCB
Known issues:
- Broadband LED (missing GPIO - probably driven by the BCM6318)
- Internet LED (missing GPIO - probably driven by the BCM6318)
- WIFI LED (working only for one interface at a time, while in the
OEM firmware works for both wifi interfaces; thus, this patch does
not set a trigger by default)
- DSL not working (eth0)
UART connection
---------------
J1 HEADER (Qualcomm CPU)
. VCC
. GND
. RX
O TX
J41 HEADER (Broadcom CPU)
. VCC
. GND
. RX
O TX
The following instructions require a connection to the J1 UART header
and are tested for the Archer D7 v1.
For the Archer D7b v1, names should be changed accordingly.
Flash instructions under U-Boot, using UART
------------------------------------------
1. Press "tpl" to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d7-v1-squashfs-sysupgrade.bin
erase 0x9f020000 +f90000
cp.b 0x81000000 0x9f020000 0xf90000
reset
Initramfs instructions under U-Boot for testing, using UART
----------------------------------------------------------
1. Press "tpl" to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d7-v1-initramfs-kernel.bin
bootm 0x81000000
4. Here you can backup the original firmware and/or flash the sysupgrade openwrt if you want
Restore the original firmware
-----------------------------
0. Backup every partition using the OpenWrt web interface
1. Download the OEM firmware from the TP-Link website
2. Extract the bin file in a folder (eg. Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin)
3. Remove the U-Boot and the Broadcom image part from the file.
Issue the following command:
dd if="Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin" of="Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin.mod" skip=257 bs=512 count=31872
4. Double check the .mod file size. It must be 16318464 bytes.
5. Flash it using the OpenWrt web interface. Force the update if needed.
WARNING: Remember to NOT keep settings.
5b. (Alternative to 5.) Flash it using the U-Boot and UART connection.
Issue below commands in the U-Boot:
tftpboot 0x81000000 Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin.mod
erase 0x9f020000 +f90000
cp.b 0x81000000 0x9f020000 0xf90000
reset
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[cosmetic DTS changes, remove TPLINK_HWREVADD := 0, do not use two
phyXtpt at once, add missing buttons, minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link Archer C60 v3 is a dual-band AC1350 router,
based on Qualcomm/Atheros QCA9561 + QCA9886.
It seems to be identical to the v2 revision, except that
it lacks a WPS LED and has different GPIO for amber WAN LED.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 6x LED, 2x button
- UART header on PCB
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server
8. Wait ~30 second to complete recovery
While TFTP works for OpenWrt images, my device didn't accept the
only available official firmware "Archer C60(EU)_V3.0_190115.bin".
In contrast to earlier revisions (v2), the v3 contains the (same)
MAC address twice, once in 0x1fa08 and again in 0x1fb08.
While the partition-table on the device refers to the latter, the
firmware image contains a different partition-table for that region:
name device firmware
factory-boot 0x00000-0x1fb00 0x00000-0x1fa00
default-mac 0x1fb00-0x1fd00 0x1fa00-0x1fc00
pin 0x1fd00-0x1fe00 0x1fc00-0x1fd00
product-info 0x1fe00-0x1ff00 0x1fd00-0x1ff00
device-id 0x1ff00-0x20000 0x1ff00-0x20000
While the MAC address is present twice, other data like the PIN isn't,
so with the partitioning from the firmware image the PIN on the device
would actually be outside of its partition.
Consequently, the patch uses the MAC location from the device (which
is the same as for the v2).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since there exists another variant of the Bullet M with AR7240 SoC
under the same name, this patch introduces the SoC into the device
name to be able to distinguish these variants.
Signed-off-by: Russell Senior <russell@personaltelco.net>
[add commit message, adjust model in DTS, fix 02_network and
SUPPORTED_DEVICES]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* Prepare to support the AR7240 variant of ubiquiti bullet m, by
reorganizing the related dtsi files.
* Distribute SOC variable across ubnt-xm devices.
Signed-off-by: Russell Senior <russell@personaltelco.net>
The PoE hat supported on the RPi 3B+ and 4B comes with a rather
loud fan, tripped in two steps by the brcmstb_thermal
thermal_zone driver. Enabling writable trip points allow
users to adjust the fan trip points according to their
preferred temp/noise ratio.
This setting is enabled on most other targets with similar
thermal_zone controlled cooling devices.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
We do not build images with a jffs2 rootfs, but jffs2 is still used as
filesystem for the rootfs_data.
Fixes: e3eaf57808 ("lantiq: kernel 5.4: debloat kernel config")
Signed-off-by: Mathias Kresin <dev@kresin.me>
When creating the mikrotik subtarget, the execute bit on 02_network
was not set. Fix it.
Fixes: a66eee6336 ("ath79: add mikrotik subtarget")
Reported-by: Christopher Hill <ch6574@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, specifying "BOARD_NAME := routerboard" is required by the
upgrade code of Mikrotik NAND devices, as "sysupgrade-routerboard"
is hardcoded in platform_do_upgrade_mikrotik_nand().
This patch replaces the latter with a grep for the name like it
is already done in nand_upgrade_tar() in /lib/upgrade/nand.sh.
By that, BOARD_NAME is obsolete now for this device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, specifying "BOARD_NAME := routerboard" is required by the
upgrade code of Mikrotik NAND devices, as "sysupgrade-routerboard"
is hardcoded in platform_do_upgrade_mikrotik_rb().
This patch replaces the latter with a grep for the name like it
is already done in nand_upgrade_tar() in /lib/upgrade/nand.sh.
This should enable upgrades from ar71xx to ath79 without setting
BOARD_NAME for the latter.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit creates the ath79/mikrotik subtarget in order to support
MikroTik devices based on Qualcomm Atheros MIPS SoCs.
MikroTik devices need a couple of specific features: the split MiNOR
firmware MTD format, which is not used by other devices, and the 4k
sector erase size on SPI NOR storage, which can not be added to the
ath79/generic and ath79/nand subtargets now.
Additionally, the commit moves the two MikroTik devices already in
the generic and nand subtargets to this new one.
Tested on the RB922 board and the wAP AC router.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Pogoplug V3/Pro has an interanl SATA port. To use it, DTS sata node should be
enabled, and kmod-ata-oxnas-sata package needs to be installed.
Fixes: FS#2542
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Build the latest kernel by default, since testing did not show any
regressions.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[fix merge conflict in tegra/Makefile]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit also disables Trusted Foundations firmware support as this
feature won't be used by any device.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[fix merge conflict in tegra/Makefile]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This new symbol popped up in few places. Disable it in generic config.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[fixed merge conflict in generic/config-5.4]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
More testing after kernel upgrade to 5.4 uncovered a regression: the user
led is not present anymore due to a pin mux "collision" in device tree.
A patch sent to upstream kernel was accepted now. Integrate this
pending fix as platform specific patch so that user led is available again.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
The etop driver is used by all targets except xrx200.
Remove the UBIFS compression support for zlib and zstd from the xway
subtarget. The hardware is EOL for a long time and it's unlikely to ever
see a board shipped with an UBIFS using these compression methods.
Remove the JFFS2 support. Support for jjfs2 images was dropped years
ago.
It shrinks the compressed kernel up to 130 KByte.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Switch to the mainline Lantiq PCIe PHY driver and update the vr9.dtsi
accordingly.
The Lantiq IRQ SMP support added upstream required changes to the SoC
dtsi as well.
Following changes are made to the Lantiq kernel patches:
0005-lantiq_etop-pass-struct-device-to-DMA-API-functions.patch
0006-MIPS-lantiq-pass-struct-device-to-DMA-API-functions.patch
applied upstream
0008-MIPS-lantiq-backport-old-timer-code.patch
access_ok API update because it lost it's type (which was the first)
parameter in upstream commit 96d4f267e40f95 ("Remove 'type' argument
from access_ok() function")
0024-MIPS-lantiq-autoselect-soc-rev-matching-fw.patch
merged into 0026-MIPS-lantiq-Add-GPHY-Firmware-loader.patch
0024-MIPS-lantiq-revert-DSA-switch-driver-PMU-clock-chang.patch
revert upstream changes required for upstream xrx200 ethernet and
xrx200 (DSA) switch driver but breaking our driver
0026-MIPS-lantiq-Add-GPHY-Firmware-loader.patch
required for our driver but dropped upstream, add former upstream
version
0028-NET-lantiq-various-etop-fixes.patch
now has to use the phy_set_max_speed API instead of modifying
phydev->supported. Also call ltq_dma_enable_irq() in
ltq_etop_open() based on upstream commit cc973aecf0b054 ("MIPS:
lantiq: Do not enable IRQs in dma open")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This is referenced in two .dts but never actually used from userspace.
Drop support for this property because it's not used and because it
makes updating to Linux 5.4 harder (as the patch doesn't apply anymore).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Duplicate kernel 4.19 config and patches for kernel 5.4.
Duplicate the devicetree source files as well, they need kernel 5.4
specific adjustments.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Compiling the ltq-tapi driver against Linux 5.4 results in a compile
error complaining that the size of struct sched_param is not known.
Switch the existing "sched/types.h" include to reference
include/uapi/linux/sched/types.h to fix compilation against Linux 5.4.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Upstream commit 84ede58dfcd1d ("crypto: hash - remove
CRYPTO_ALG_TYPE_DIGEST") drops the CRYPTO_ALG_TYPE_DIGEST define because
it has the same value as CRYPTO_ALG_TYPE_HASH. This was the case for
earlier kernels as well. Switch to CRYPTO_ALG_TYPE_HASH to fix building
against Linux 5.4.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Upstream commit e4b92b108c6cd6 ("timekeeping: remove obsolete time
accessors") removed do_gettimeofday(). In Linux 4.19 this was only a
wrapper around ktime_get_real_ts64(). Use ktime_get_real_ts64() now that
the wrapper is gone to fix compilation against Linux 5.4.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Upstream commit e4b92b108c6cd6 ("timekeeping: remove obsolete time
accessors") removed do_gettimeofday(). In Linux 4.19 this was only a
wrapper around ktime_get_real_ts64(). Use ktime_get_real_ts64() now that
the wrapper is gone to fix compilation against Linux 5.4.
Move the ifxmips_mei_interface header to the include directory, it can't
be found otherwise during compilation. The reason for the changed
behaviour is not yet clear, however having header files in an include
directory is more straight forward.
To use the of_device_id struct, the mod_devicetable header need to be
included. Instead of including this header, include the of_platform
header, which includes the mod_devicetable on its own.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Upstream commit 96d4f267e40f95 ("Remove 'type' argument from access_ok()
function") removes the first argument to access_ok.
Adjust the code so it builds with Linux 5.4.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Beginning with linux 5.3, kmod-serial-8250 uses functions provided by
serial_mctrl_gpio.ko if GPIO support is enabled.
Signed-off-by: Mathias Kresin <dev@kresin.me>
It adjusts the code to upstream changes from the commit 3c1bcc8614db
("net: ethernet: Convert phydev advertize and supported from u32 to link
mode")
Signed-off-by: Mathias Kresin <dev@kresin.me>
For some reason pin 7 (gphy0_led1_pins) need to be set to output prior
to loading the PCI driver. Otherwise the wireless doesn't appear on the
PCI bus. Of course, it doesn't make much sense, since pin 7 is used to
drive the LAN1 led.
It can either be done by setting the pins function to GPHY or GPIO +
direction output. However, the pinctrl driver doesn't provide a way to
switch a pin to GPIO. It is done indirectly by the pinctrl driver at the
time a GPIO is requested (requesting a GPIO always resets the function
to GPIO).
Do it via pinmux driver, as it is always loaded first. Use the GPHY
function as it's the pins intended purpose for this board.
Fixes: FS#2895
Signed-off-by: Mathias Kresin <dev@kresin.me>
There is no such role as target maintainer anymore, one should always
send corresponding changes for the review and anyone from the commiters
is allowed to merge them or eventually use the hand break and NACK them.
Lets make it clear, that it is solely a community doing the maintenance
tasks.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
In 5.4 kernel old u32 array way of setting network features was dropped and linkmode is now the only way.
So lets migrate the EDMA driver to support linkmode.
Also, old get/set settings API for ethtool is also dropped so lets convert to new ksettings API while at it as it demands linkmode.
Now, gigabit works properly as well as ethtool.
Previously you would get this in ethtool:
root@OpenWrt:/# ethtool eth1
Settings for eth1:
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000000 (0)
Link detected: yes
Now, features are properly advertised:
root@OpenWrt:/# ethtool eth1
Settings for eth1:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: No
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 4
Transceiver: internal
Auto-negotiation: on
MDI-X: Unknown
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000000 (0)
Link detected: yes
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
In 5.4 kernel old u32 array way of setting network features was dropped and linkmode is now the only way.
So lets migrate the PHY driver to support linkmode.
Also, now in order for gigabit to work, PHY driver needs to advertise PHY_GBIT_FEATURES instead of PHY_BASIC_FEATURES
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
of_get_mac_address returns valid pointer or ERR_PTR since 5.2 via commit
d01f449c008a ("of_net: add NVMEM support to of_get_mac_address") so the
patch fixes following OOPs on nbg6617:
Unable to handle kernel paging request at virtual address ffffffed
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.4.24 #0
PC is at edma_axi_probe+0x444/0x1114
LR is at bus_find_device+0x88/0x9c
Where the PC can be resolved to:
>>> l *edma_axi_probe+0x444
0xc067be5c is in edma_axi_probe (./include/linux/string.h:378).
>>> l *edma_axi_probe+0x43f
0xc067be57 is in edma_axi_probe (drivers/net/ethernet/qualcomm/essedma/edma_axi.c:936)
Which leads to the following code fragment:
935 mac_addr = of_get_mac_address(pnp);
936 if (mac_addr)
937 memcpy(edma_netdev[idx_mac]->dev_addr, mac_addr, ETH_ALEN);
Where using mac_addr=0xffffffed (-ENODEV) as source address in memcpy()
is causing the OOPs.
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
These new options are common for all subtargets and can be moved into target kconfig.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
This was done by executing these command for all subtargets:
$ time make -j9 kernel_oldconfig CONFIG_TARGET=subtarget
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
These patches are already in mainline 5.4 kernel:
* 010-v5.3-drivers-ata-ahci_sunxi-Increased-SATA-AHCI-DMA-TX-RX.patch
* 101-arm64-dts-allwinner-a64-Enable-A64-timer-workaround.patch
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Seems to be working fine on apu2 and QEMU, it's 99.9% upstream stuff
anyway. Lets start wider userbase testing.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Commit 432ec292cc ("rpcd: add respawn param") has introduced infinite
restarting of the service which could be reached over network. This is
not recommended security practice as it might give potential adversary
infinite number of tries in case there might be some issue in the rpcd
or its surrounding stack.
So lets remove the currently bogus `respawn_retry` variable (it wasn't
possible to override it anyway), reverting to the previous default max.
of 5 service restarts which could be now overriden via system's UCI
settings if desired.
Cc: Jo-Philip Wich <jow@mein.io>
Cc: Florian Eckert <fe@dev.tdt.de>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Fixes: 432ec292cc ("rpcd: add respawn param")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Davide Fioravanti
Adrian Schmutzler
Russell Senior
Bjørn Mork
Mathias Kresin
Roger Pueyo Centelles
Leon M. George
Sungbo Eo
Tomasz Maciej Nowak
Michael Heimpold
Luis Araneda
Martin Blumenstingl
Petr Štetiar
Robert Marko
Aleksander Jan Bajkowski