Renaming an atm etherbride using 'ip link' (via hotplug) is racy since the
original netdev might disappear before br2684ctl has finished appling it's
setting:
local2.notice br2684ctl[1667]: Interface "nas0" created sucessfully
local2.notice br2684ctl[1667]: Communicating over ATM 0.8.35, encapsulation: LLC
kern.info kernel: dsl0: renamed from nas0
kern.err kernel: br2684:br2684_regvcc: tried to attach to non-existent device
local2.err br2684ctl[1667]: Could not configure interface:No such device or address
By passing the final used netdev name to br2684ctl_wrap another race
condition workaround will be enabled again.
Change the lantiq ptm driver to create a netdev with the name dsl as well.
Albeit the rename via 'ip link' works fine so far, using a different
approach for ptm then atm could be confusing.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Albeit ltq-ptm is supported on AmazonSE, the package fails to compile.
Mark the AmazonSE variant as broken to not mark it unnecessary harder
to fix (and test) the compile error.
Signed-off-by: Mathias Kresin <dev@kresin.me>
commit 2d6c7c2526 introduced a reference to g_xdata_addr which isn't
defined in that context. Use xdata_addr here instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is needed to be able to load the ltq-atm/ltq-ptm driver
from a notify script during synchronization, because the line can
reach showtime state before the driver is fully loaded.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Tested with VDSL on TP-Link WD8970, I see full 1500-byte PPP data
frames, which end up being 1526 byte Ethernet frames (including
Ethernet+VLAN headers) on the wire.
Fixes: FS#210
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Principal purpose is to prevent the error message
ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
which is printed at least once per second to the serial console, if the
ptm interface is not in showtime, but a processes already sends
packages over that interface. This happens for adsl as well as vdsl
over ptm.
It's pppd which sends packages over the ptm device before in showtime.
As far as I can see, pppd is started unconditionally since netif can
not gather the link status of the ptm network interface.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47917
buildbot complained about
ifxmips_ptm_adsl.c:1445:70: error: macro "alloc_netdev" requires 4 arguments, but only 3 given
g_net_dev[i] = alloc_netdev(0, g_net_dev_name[i], ether_setup);
^
fix that similar to the change made to ltq_ptm_vdsl.c
compile tested only.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 44632
The initial fix for 3.18 in r44346 wrongly treated the newly added
parameter of alloc_netdev to be another function pointer, causing
ether_config to be skipped during ptm netdev init.
Fix this by partially reverting r44346 and properly setting the newly
added macro parameter.
(Tested on VRX200 board)
A similar change might be needed for ltq-ptm-adsl as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 44607
Mathias Kresin
Jonas Gorski
Daniel Golle
Martin Schiller
Florian Eckert
Hauke Mehrtens
Alexandru Ardelean
David Woodhouse
John Crispin
John Crispin