8cc16aa14e
add support for HW553 bcm6358-based boards ( #8844 )
...
SVN-Revision: 25590
2011-02-19 15:44:06 +00:00
44e22cbd49
Fixed Comtrend CT536_CT5621 board settings. These boards are based on the 96348GW-11 reference design but have different GPIOs therefore we use the board fixups now availabed (thanks the patches by Jonas Gorski) to create a separate board entry for these boards and leave the reference design with reference GPIOs. Also these boards only have enet1 (no enet0) so we set that in the board definition, and use a defconfig for a single interface network.
...
SVN-Revision: 24442
2010-12-10 18:59:58 +00:00
8f9b14dafe
boards: Added GW6x00 fixups and GPIOs. The GW6200 GPIOs are different than the reference design 96348GW so we use fixup to allow us to define the correct ones, also the GW6000 has no GPIO-controlled leds.
...
SVN-Revision: 24305
2010-12-07 15:15:54 +00:00
9677b65cb6
image Makefile: Corrected router imagename length limiting. Thanks KanjiMonster for reminding me.
...
SVN-Revision: 24191
2010-11-28 22:13:00 +00:00
314bce63e6
bcm63xx: Add support for the T-Com Speedport W 500V.
...
Add support for the T-Com Speedport W 500V using a special tagged image as it
identifies itself as a 96348GW, but has some gpios wired differently, and also
has only one ethernet port without a switch attached to it.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 24190
2010-11-28 22:04:44 +00:00
3a49f669f2
bcm63xx: Add board id override fixup.
...
Add a fixup for the kernel to check the bcm tag of the image for a boardid in
the information1 field, and use that instead of the supplied one by cfe. This
is triggered by a + at the start of the information1 field.
Also modify the image generation to generate apropriately tagged images.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 24189
2010-11-28 22:04:40 +00:00
c51d772e62
bcm63xx: Finalize support for DSL-274xB, rev C2.
...
The DSL-2740B/DSL-2741B rev C2 support was missing the board definition,
resulting in a kernel panic on boot.
This patch adds it, and also renames the generated image name to properly
reflect that it is for the revision C2, and for both the DSL-2740B and
DSL-2741B.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 24188
2010-11-28 22:04:36 +00:00
195d1d7446
image Makefile: Removed extraneous tab from Image/LimitName16 macro definition. The solves the strange whitespace in front of the image name in the info1 section
...
SVN-Revision: 24127
2010-11-24 11:06:13 +00:00
0c0c1f017f
image: Limited image name put into the info1 field to 16 characters and eliminted the OpenWRT revision. This makes using the image (router) name as the board name possible, so that boards with same real boardid but different GPIOs can be detected and the correct GPIOs used.
...
SVN-Revision: 24118
2010-11-23 20:17:08 +00:00
049e59a27b
Initial support for Telsey CPVA642 boards (no vlans, no DSL, GPIO led/buttons not known).
...
SVN-Revision: 24040
2010-11-19 13:41:54 +00:00
eadb5c84fa
imagetag: Significantly updated brcm63xx imagetag writing tool. * Rewrote commandline parsing code using gengetopt - We now get long options - We have more options including use of the info section for board information (e.g. to add the same boardid but different GPIOs on different routers) * Added back the ability to write stock images (this is useful, for example, when copying the firmware from the in-memory flash, and then being able to create an image that will let you revert to/test stock firmware * Fixed copying of CRCs to use memcpy instead of strncpy (strncpy stops at 0) * Added ability to use all sections of the imagetag, including custom magic signatures (e.g. for the Telsey router I'm adding soon), info sections, and reserved sections * Added putting the router type (as defined in the image generating Makefile) into the info1 section and the filesystem type in the info2 section. This will be used by mtd (when I add the code) to return the name of image used to flash this router. (As requested by Jo, as well as being useful for same boardid different board scenario described above).
...
SVN-Revision: 24011
2010-11-16 06:46:53 +00:00
e2b57ecf5f
define a shared IMG_PREFIX variable used as a basename for image files, it contains board & subtarget infos (if appropriate) allowing subtargets to share the same bin directory without overwriting each other's files
...
SVN-Revision: 20834
2010-04-12 23:15:56 +00:00
2a4fb82289
flashmap and image generation: reduced union bcm_tag to a single struct combining the elements so that it is no longer necessary to create an openwrt-only tagid and tagcrc, and elimate the tagid detection and switch statements which made dealing with imagetags overly complicated, especially since the logic would need analogs in all code that touched the imagetag. Patch from cshore.
...
SVN-Revision: 20652
2010-04-01 21:20:43 +00:00
ada5848ba6
build images for RG100A (bcm6358-based boards) ( #6755 )
...
SVN-Revision: 19894
2010-02-28 11:09:39 +00:00
411d1ba1bb
do not generate trx images, this is useless
...
SVN-Revision: 18204
2009-10-29 13:39:29 +00:00
85698765da
add support for the Pirelli AG226G board ( #5337 )
...
SVN-Revision: 17190
2009-08-09 10:19:47 +00:00
dd622864e1
generate images for RTA1025W_16-based routers ( #5594 )
...
SVN-Revision: 17058
2009-07-31 10:47:00 +00:00
45c25ff988
generate images for the bcm6338w
...
SVN-Revision: 16566
2009-06-26 10:27:37 +00:00
1795111337
add imagetag support for BT Voyager 2500V, patch from Daniel Dickinson ( #5364 )
...
SVN-Revision: 16506
2009-06-18 15:00:32 +00:00
606193fc1f
generate experimental images for bcm6338 boards, thanks to Daniel Dickinson
...
SVN-Revision: 16490
2009-06-17 13:16:59 +00:00
cc12508ee3
use build system REVISION variable ( #5317 )
...
SVN-Revision: 16400
2009-06-10 13:43:48 +00:00
ca16accfbb
The attached patch adds building of firmware images for more routers based on the brcm63xx chipset.
...
Signed-Off By: Daniel Dickinson <crazycshore@gmail.com>
SVN-Revision: 16396
2009-06-10 08:24:13 +00:00
01118457e8
rework imagetag firmware generator and MTD partition parser to accomodate with all known imagetag versions from Broadcom and vendors, patch from Daniel Dickinson ( fixes #4987 ).
...
SVN-Revision: 16393
2009-06-09 08:04:52 +00:00
1f334e3caa
make images that can be flashed using the stock firmware web interface, thanks to Anselmo Luginbuhl and Daniel Dickinson ( #4909 , #4943 )
...
SVN-Revision: 15253
2009-04-19 13:18:48 +00:00
5d5c8300b1
imagetag's -k argument is expected to be hexadecimal instead of decimal ( #4885 )
...
SVN-Revision: 15133
2009-04-07 13:22:32 +00:00
b865f9b722
add the CFE offset command line option to the imagetag utility, closes ( #4366 )
...
SVN-Revision: 14896
2009-03-16 12:29:11 +00:00
6495fa36ea
add support for AGPF-S0 (Pirelli Alice Gate VoIP 2 Plus Wi-Fi) #4366
...
SVN-Revision: 14850
2009-03-12 08:54:04 +00:00
730346e2d5
add support for user9102 boards ( #4537 )
...
SVN-Revision: 14305
2009-01-31 16:01:20 +00:00
c2c0d74f67
generate images for old CFE based boards like the Davolink DV201
...
SVN-Revision: 14264
2009-01-29 14:56:45 +00:00
562ff99c2c
Build images for Inventel Livebox
...
SVN-Revision: 13616
2008-12-12 15:16:57 +00:00
4025c12a2d
Fix typo, we are not building for the DG834G (ar7) but the DG834GT (brcm6348)
...
SVN-Revision: 13588
2008-12-10 23:57:23 +00:00
4dc65aed63
Add support for Sagem F@ST2404 ( #4332 )
...
SVN-Revision: 13583
2008-12-10 16:13:41 +00:00
f3be50a031
Add support for bcm96348gw10 (Netgear DG834GT) ( #4319 )
...
SVN-Revision: 13540
2008-12-07 20:34:48 +00:00
107aa04e06
Generate valid images for the bcm96348gw board
...
SVN-Revision: 13298
2008-11-20 21:22:45 +00:00
0d4286b0b3
This patch is for broadcom 96348GW-11 boards, to get USB and Ethernet working. Also it patches mtd map driver for bcm96xx boards to be sure that CFE1CFE1 code is detected when booting from CFE. ( #4201 )
...
SVN-Revision: 13213
2008-11-15 11:30:22 +00:00
691e187381
Add definitions for bcm96350vw, add back bcm63xx mtd driver, be careful when testing with 8MB devices
...
SVN-Revision: 13015
2008-10-20 12:55:28 +00:00
2dfabe3991
bcm963xx: image generation using image tagger
...
This adds CFE tagged image generation in the BCM963xx target image Makefile.
It has to generate its own LZMA compressed kernel because CFE is a LZMA nazi.
It also seems that the Broadcom image tagger as well as CFE use AdvanceCOMP,
which is based on a slightly older LZMA SDK. Anyways, some of the code is
GPL, some of it is LGPL, so it might be that Broadcom owes some sources.
Also, LZMA has a bug which causes it to generate different output when you
are using stdin / stdout compared to plain files. I've just worked around
the issue by using plain files.
Signed-off-by: Axel Gembe <ago@bastart.eu.org>
SVN-Revision: 11171
2008-05-18 17:30:04 +00:00
46b4413fbb
bcm963xx: fix load address / kernel entry
...
Current kernels have the same kernel entry as load address, so just set them
like this. Also, the BCM963xx uses 0x80010000 as its load address, so use this
too.
Signed-off-by: Axel Gembe <ago@bastart.eu.org>
SVN-Revision: 11169
2008-05-18 17:29:39 +00:00
e3a42b23c6
enable proper PCI & USB support detection at config-time by disabling CONFIG_PCI & CONFIG_USB entries in generic/config and enabling them on targets where appropriate
...
SVN-Revision: 11097
2008-05-09 17:08:51 +00:00
62240465c4
brcm63xx image generation cleanups ( #3169 )
...
SVN-Revision: 10703
2008-04-01 21:10:47 +00:00
1bca0cc517
make the image filenames a bit shorter
...
SVN-Revision: 9533
2007-11-10 23:08:11 +00:00
56231056ea
strip the kernel version suffix from target directories, except for brcm-2.4 (the -2.4 will be included in the board name here). CONFIG_LINUX_<ver>_<board> becomes CONFIG_TARGET_<board>, same for profiles.
...
SVN-Revision: 8653
2007-09-06 16:27:37 +00:00
Florian Fainelli
Daniel Dickinson
Nicolas Thill
Felix Fietkau