ALFA Network R36A is a successor of the previous model, the R36 (Ralink
RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2.
Specification:
- 650/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R (QCA9531) 2.4 GHz, 2x u.fl connectors on PCB
- 1x USB 2.0 (power controlled by GPIO)
- 6x LED (5 of them are driven by GPIO)
- 2x button (reset, wifi/wps)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- DC jack for main power input (12 V)
- UART header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Teltonika RUT900 is an industrial 3G router based on Atheros AR9344.
There are available 3 other models in RUT9xx series: RUT905, RUT950 and
RUT955, which differ in availability of additional I/O ports, built-in
GSM modem type, GPS antenna and other features. FCC ID of the RUT950
model (LTE module built-in): 2AET4-RUT950.
This patch adds support for the RUT900 model only but can be easily
extended to cover whole series. Also, as there are several different
3/4G modules (Huawei, Quectel, Telit) used in whole series, packages
required for WWAN support are not included by default. It is up to the
user to install required software for built-in modem.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344), with ext. PA (MGA-22103) and LNA
- built-in 3G module (example: Telit HE910-D)
- 2x miniSIM slot
- 2x RP-SMA/F (Wi-Fi), 2x SMA/F (3G)
- PCA9539 16-bit GPIO I2C expander
- 12x LED (4 are driven by AR9344, 7 by PCA9539)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- UART available on PCB edge connector
Serial console pinout:
- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side
Flash instruction:
Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.03.960" firmware and U-Boot "3.0.1".
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network N5Q is a successor of previous model, the N5 (outdoor
CPE/AP, based on Atheros AR7240 + AR9280). New version is based on
Atheros AR9344.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 5 GHz (AR9344), with ext. PA (RFPA5542) and LNA, up to 27 dBm
- 8x LED (7 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmare which is based
on OpenWrt/LEDE. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network AP91-5G is a 5 GHz outdoor AP/CPE board, based on Atheros
AR7240 + AR9280.
Specification:
- 400/400/200 MHz (CPU/DDR/AHB)
- 32 MB of RAM (DDR1)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 1T1R 5 GHz (AR9280), with ext. PA (SE5004L) and LNA, up to 27 dBm
- 6x LED (5 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART and LEDs headers on PCB
Flash instruction:
Use "factory" image in vendor GUI (in case of problems, make sure your
board has up to date firmware). Alternatively, TFTP in U-Boot can be
used: select option "2. Load system code then write to Flash via TFTP"
during early boot and use "sysupgrade" image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The KEXEC_FILE symbol exists for X86 since kernel 3.17, and since 4.10
for PPC64. Add it to x86/config-4.9 and to generic/config-4.14.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Several new DRM symbols that were introduced after 4.9 are missing in
the generic config for 4.14, so add them.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
While working on a new target (meson), the kernel build failed due to
missing DRM_DEBUG_MM_SELFTEST symbol. This can potentially happen on all
targets that enable DRM drivers in the kernel config or via kmod
packages, so add it to the generic config and remove it from x86
subtarget configs, together with DRM_DEBUG_MM.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This new subtarget sets the small_flash flag and removes unused kernel
configuration.
small_flash removes KERNEL_KALLSYMS, which saves ~107KB in the default
configuration; removing unneeded hardware support from ar71xx/tiny saves
another ~18KB (both after LZMA).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Rather than including all machines for the generic subtarget in the base
configuration, leave the base configuration without specific machines and
create a proper subtarget config for ar71xx/generic. The configuration
diffs of the mikrotik and nand subtargets get significantly shorter, as
will the configurations of future subtargets.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
While we'd like to convert ar71xx to DT-based configuration
eventually, we aren't quite there yet, and shipping half-baked DT support
that is not used at all wastes precious space.
Saves ~120KB before LZMA, ~33KB after LZMA.
Run-tested on TP-Link CPE510 and TL-WR841 v7.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Disable CONFIG_PROC_PAGE_MONITOR in most places and only keep it enabled
for virtual targets such as malta or potent ones like x86.
This saves up to 4KB of uncompressed kernel size and significantly
decreases CPU load under certain workloads.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* QCA IPQ401x
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
* powered only via POE
- 802.3af POE on Ethernet 1
- 18-24v passive POE (mode B) on Ethernet 2
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The kernel driver gpio-wdt or the userspace tool om-watchdog can be used to
trigger external gpio watchdog chips. The gpio-wdt driver has the benefit
that it can be configured together with the rest of the device in the DTS
and better integrates in the OpenWrt via procd.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Use the generic board detection method:
- Board name: First compatible string from the device tree
- Board model: Model property from the device tree
Change occurrences of board name in userspace by the compatible
string, and removed target specific board detection script
Replace the definition of SUPPORTED_DEVICES in Device/Default
to extract the dt compatible string from each device definition.
Additionally, for devices supported by lede-17.01, append
the value of BOARD_NAME to SUPPORTED_DEVICES in the device
definition.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Use <manufacturer>_<modelname> as image name for board using the
devicetree compat string as boardname.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
This will allow to maintain the current syntax for LEDs config
when switching to a device tree compatible string boardname.
None of the current boards use a comma in the boardname, so they
will be unaffected.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
There are only artifacts for these boards in our tree and not even
partial support.
Drop teh stale files.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The 4.14 kernel configuration defaulted to a v4/v5 multiplatform while
4.9 was using a v6/v7 default configuration. Resync 4.14 against 4.9 so
they are nearly identical.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a bunch of missing configuration symbols found while building
armvirt for 4.14 after re-synchronization of the configuration between
4.9 and 4.14.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch updates the apm821xx target to use the 4.14 kernel.
4.14 finally ships with a driver for the WNDR4700's tc654 fan
controller. The custom driver is deprecated in favor of the
upstream driver and the thermal cooling definitions in the DTS
are updated.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Without this patch one sdcard image with the following name is created
for all devices:
openwrt-at91-sama5--sdcard.img.gz
This makes the build system create device specific versions like:
openwrt-at91-sama5-at91-sama5d2_xplained-sdcard.img.gz
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This solution is more upstream compatible as it only requires specifying
of_match_table in the parser code and doesn't depend on linux,part-probe
which is solution made generic by a LEDE downstream patch that can't be
upstreamed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This backports upstream support for "compatible" DT property set for the
"partitions" subnode of flash node. It allows specifying how partitions
should be created/parsed. Right now only "fixed-partitions" is
supported.
It should eventually replace our downstream "linux,part-probe" solution.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Multicast routing support is not needed in most setups, and increases the
size of the kernel considerably (>10K after LZMA). Add a config switch to
allow disabling it.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The underlying issue breaking Spansion flash has been fixed with "mtd: spi-nor:
wait until lock/unlock operations are ready" and "mtd: spi-nor: wait for SR_WIP
to clear on initial unlock", so we can support unlocking for Winbond flash
again.
This is necessary to have writable flash on certain UBNT devices with some
bootloader versions.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Renaming an atm etherbride using 'ip link' (via hotplug) is racy since the
original netdev might disappear before br2684ctl has finished appling it's
setting:
local2.notice br2684ctl[1667]: Interface "nas0" created sucessfully
local2.notice br2684ctl[1667]: Communicating over ATM 0.8.35, encapsulation: LLC
kern.info kernel: dsl0: renamed from nas0
kern.err kernel: br2684:br2684_regvcc: tried to attach to non-existent device
local2.err br2684ctl[1667]: Could not configure interface:No such device or address
By passing the final used netdev name to br2684ctl_wrap another race
condition workaround will be enabled again.
Change the lantiq ptm driver to create a netdev with the name dsl as well.
Albeit the rename via 'ip link' works fine so far, using a different
approach for ptm then atm could be confusing.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Enable CONFIG_VFP again which was disabled during the 4.9 -> 4.14 bump.
Boot tested both 32 and 64 bit subtargets using initramfs images with the
qemu-system-arm and qemu-system-aarch64 emulators.
Fixes: aa100b66f2 ("armvirt: bump to v4.14")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
also known as
POGO-V4-A3-02
or
POGO-V4-A3-01
SoC: Marvell 88F6192 800Mhz
SDRAM memory: 128MB
Gigabit ethernet: 1 Marvell 88E1310
Flash memory: 128MB
2 status LEDs (one green one red)
1 "Eject" button on the back (used as "Reset" button)
1 USB 2.0 port (on upper side)
1 sata slot (power + data) for 2.5'' drives (upper side)
2 USB 3.0 ports from a controller on PCIe x1 of the SoC
1 full-size SDcard slot (fits a whole SD card into it)
This device supports the (linux-only) kwboot tool to send
a new uboot over serial console, so it is easy to unbrick
in case the uboot is erased and the device won't boot.
-----
Install instructions:
-----
Since it's not possible to get ssh access to these
devices, the only way to take control is to
solder pins to get TTL serial access.
Case can be opened by removing screws beneath two rubber
feet at back of device, then lifting while prying the
sides of the upper part out to unhook a latch on each
side about 2/3rds of the way toward the front.
Serial connection pins are those labeled "J11", left
of SD as you face SD opening.
Pins are (from left to right, i.e. the first in the list
is the nearest to the SD slot) GND, Rx, Tx.
Do not connect +V pin if you use a USB (self-powered)
TTL-to-USB dongle. Any USB TTL-to-USB converter will work.
Baud rate is 115200, parity "none", databits "8",
flow control "none".
Stock uboot is unable to read ubi partitions (nor usb)
so we will replace it first with our uboot.
Start a TFTP server at IP address 169.254.254.254, and
place the uboot.kwb file in the folder of the server.
Start the serial session and then power up the device.
As soon as you see text on the serial start pressing random
letter keys to stop the boot process.
If you see something like the following line you can proceed:
CE>>
Otherwise if text is still scrolling by you missed the
opportunity, pull the plug and try again.
write
printenv ethaddr
The uboot will write something like this:
ethaddr=00:50:43:00:02:02
This is the device's MAC address, also present in the sticker
under the device.
Write this down as we will need to add it in the
new uboot configuration.
Use the following commands to load the new uboot:
tftp 0x20000 u-boot.kwb
If the uboot confirms that the transfer was successful,
then you can write it to flash with the following commands:
nand erase 0 0x200000
nand write 0x20000 0 0x1c0000
if after the last command the uboot wrote
"xxxx bytes written: OK"
then it was written correctly and we can proceed.
If it did not go well, try again or ask assistence in forums.
Shutting down or rebooting at this time will brick
the device, to unbrick it you will need to use the kwboot
tool from a Linux PC or Virtual Machine.
Now write:
reset
and press enter, the device will reboot and you should see
again text scrolling by.
Press a random key to stop it, and now you should see
pogoplugv4>
We now add the MAC address back, write:
setenv ethaddr '00:50:43:00:02:02'
Confirm that the uboot has understood by writing
printenv ethaddr
If all looks ok, save the setting with
saveenv
At this point the uboot is configured, and we only need to load
the firmware in the flash memory.
Follow the steps below in "Firmware recovery procedure".
----
Firmware recovery procedure
----
The new uboot allows easy recovery from a bad firmware upgrade
where you can't access the device anymore over ssh or luci.
Take a USB flash drive formatted as FAT32, and copy the
initramfs image file in it (it will have "initramfs" in the
file name), then rename it as "initramfs.bin".
Insert the USB drive in the USB 2.0 port of the pogoplug
(the port at the top).
Power up the device, and wait for it to finish booting.
The uboot should find and load the "initramfs.bin"
from usb and if you are connected with serial you should
see the linux kernel boot log (text scrolling by).
Once it is done, press Enter and you will be greeted by
the OpenWRT banner.
If you were not connected with serial just wait a bit and,
you will be able to access it with ssh or luci web interface
(once you find its IP).
The recovery "initramfs" images are run from RAM, so you will
have to do a normal sysupgrade (firmware upgrade) to write
a firmware image to flash memory.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Use <manufacturer>_<modelname> as image name.
Use the BOARD_NAME variable to ensure that the former used boardname is
still used as the subdirectory name for the sysupgrade-tar image, to
not break sysupgrade from earlier versions.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Append and enforce image metadata. Remove the device specific image
checks, they are replaced by image metadata.
Signed-off-by: Mathias Kresin <dev@kresin.me>
There is no point in being that specifc in a generic dts covering a range
of boards. Keep only the the generic compat string to use it for a
devicetree based boardname.
Signed-off-by: Mathias Kresin <dev@kresin.me>
No image build code for the Guruplug, Sheevaplug and NSA310S exists. Drop
support for the boards for now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Drop NAND_BLOCKSIZE, UBI_OPTS and UBIFS_OPTS. They are either used by
not supported filesystems or by the legacy image build code.
Add common used options/images to the default build code and override
the options where necessary.
Don't export the kernel image, it isn't required by any board.
While at it, change the file extension for the sysupgrade images to bin.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The TP-Link firmware uses (primary_mac-1) as MAC-address
for the 5GHz WiFi. This applies the same behaviour to LEDE.
Currently, the MAC-address is retrieved from eth1, which
does not exist on the Archer C7 v4. As a result from this,
every C7 v4 with LEDE carries the same MAC-Address on the 5GHz WiFi.
Signed-off-by: David Bauer <mail@david-bauer.net>
There are 3 ethernet ports on Y1. LAN1 on port1, LAN2 on port0 and WAN on
port4.
Use a standalone switch configuration to match this and use the switch
trigger so that LAN LED could indicate the connetction status for both
lan ports correctly.
This patch also drop the internet led configuration, because there is a
WAN led for port4 and eth0.2 isn't always used as WAN.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 4.4.0 is always
false. Remove the obsolete check from mach-rb4xx.c to clean up the code
a bit.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 4.2.0 is always
false. Remove the obsolete check from ag71xx_main.c to clean up the code
a bit.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 3.15.0 is always
false. Remove the obsolete checks from the target specific source files
to clean up the code a bit.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Disable the drivers for the following ethernet switches:
Realtek RTL8306
Realtek RTL8366/8367
Marvell 88E6060 (DSA)
Marvell 88E6063 (DSA)
Also disable the phy driver for Marvell PHYs.
None of the supported RouterBOARDs are using any device
which needs these drivers.
Disable the DSA framework too, because it is not required
by the remaining switch drivers.
This reduces the compressed kernel size by ~20KB.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The Marvell 88E6063 ethernet switch driver depends on the DSA
framework. Add a 'depends on NET_DSA' statement to its Kconfig
entry to state that explicitly.
Fixes the following Kconfig warning:
warning: (NET_DSA_MV88E6060 && NET_DSA_MV88E6063) selects NET_DSA_TAG_TRAILER which has unmet direct dependencies (NET && NET_DSA)
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Building Linux 4.4 for ar71xx throws the following warnings in
drivers/net/phy/mdio-bitbang.c:
CC drivers/net/phy/mdio-bitbang.o
In file included from include/linux/irqflags.h:14:0,
from drivers/net/phy/mdio-bitbang.c:20:
drivers/net/phy/mdio-bitbang.c: In function 'mdiobb_read':
include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
(void)(&__dummy == &__dummy2); \
^
include/linux/irqflags.h:63:3: note: in expansion of macro 'typecheck'
typecheck(unsigned long, flags); \
^
include/linux/irqflags.h:124:3: note: in expansion of macro 'raw_local_irq_save'
raw_local_irq_save(flags); \
^
drivers/net/phy/mdio-bitbang.c:162:2: note: in expansion of macro 'local_irq_save'
local_irq_save(flags);
^
include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
(void)(&__dummy == &__dummy2); \
^
include/linux/irqflags.h:68:3: note: in expansion of macro 'typecheck'
typecheck(unsigned long, flags); \
^
include/linux/irqflags.h:126:39: note: in expansion of macro 'raw_local_irq_restore'
#define local_irq_restore(flags) do { raw_local_irq_restore(flags); } while (0)
^
drivers/net/phy/mdio-bitbang.c:175:2: note: in expansion of macro 'local_irq_restore'
local_irq_restore(flags);
^
drivers/net/phy/mdio-bitbang.c:159:11: warning: unused variable 'i' [-Wunused-variable]
int ret, i;
^
In file included from include/linux/irqflags.h:14:0,
from drivers/net/phy/mdio-bitbang.c:20:
drivers/net/phy/mdio-bitbang.c: In function 'mdiobb_write':
include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
(void)(&__dummy == &__dummy2); \
^
include/linux/irqflags.h:63:3: note: in expansion of macro 'typecheck'
typecheck(unsigned long, flags); \
^
include/linux/irqflags.h:124:3: note: in expansion of macro 'raw_local_irq_save'
raw_local_irq_save(flags); \
^
drivers/net/phy/mdio-bitbang.c:185:2: note: in expansion of macro 'local_irq_save'
local_irq_save(flags);
^
include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
(void)(&__dummy == &__dummy2); \
^
include/linux/irqflags.h:68:3: note: in expansion of macro 'typecheck'
typecheck(unsigned long, flags); \
^
include/linux/irqflags.h:126:39: note: in expansion of macro 'raw_local_irq_restore'
#define local_irq_restore(flags) do { raw_local_irq_restore(flags); } while (0)
^
drivers/net/phy/mdio-bitbang.c:200:2: note: in expansion of macro 'local_irq_restore'
local_irq_restore(flags);
^
These are caused by the 900-mdio_bitbang_ignore_ta_value and
901-phy-mdio-bitbang-prevent-rescheduling-during-command patches.
The first patch removes some code but it does not remove the variable
which is used by the removed code only.
The second patch adds local_irq_{save,restore} calls. The type of the
argument of these calls must be 'unsigned long', but the patch defines
the variable as 'long'.
Fix both patches to silence the warnings.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The Annex A and Annex B version are using the same (old) userspace
boardname. Update the SUPPORTED_DEVICES to allow an update from lede-17.01.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Supermicro puts "Super Server" into their product_name DMI value
for a whole slew of products, making this value about as useful
as not having been filled in at all. Instead, fall back on the
board_name instead.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
There might be other places (such as vendor-supplied preinit scripts)
where we wish to take a DMI name and clean it up in a consistent way,
so make the sed command into a function.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Rename unwinder config symbols to match upstream changes.
Refresh patches.
Update patch that no longer applies: 202-reduce_module_size.patch
Also enable CONFIG_PAGE_TABLE_ISOLATION. This feature was backported
from 4.15 to the 4.14 stable series. It is enabled by default, so enable
it in OpenWrt as well.
Compile-tested on x86/64.
Runtime-tested on x86/64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
While bumping 4.14, the kernel build failed due to missing CONFIG_KASAN
symbol. Move it to generic config instead of defining it for all arm64
and x86/64 targets.
It was only added in 4.0, so not needed in config-3.18.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The CPU sub type was set to a CPU version with FPU, but the FPU feature
was not activated before, so a soft float toolchain was created.
Activate also the FPU feature to create the correct toolchain.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This activates neon and VFPv4 support for this target. The CPU support
these feature so also use them.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since BusyBox 1.25.0 dd command supports iflag=skip_bytes which allows
skipping requested amount of bytes without reducing blocksize. Thanks to
this we can leave default blocksize and let dd work more efficiently.
On Netgear R6250 "dd skip=58 iflag=skip_bytes" can be 5 times faster
than "dd bs=58 skip=1" when extracting TRX out of CHK.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's a device based on BCM5365P (0x5365 package 0x00). This SoC has
USB 1.1 controller but device has two USB 2.0 parts. They are handled by
PCI-based controllers: 1106:3038 UHCI and 1106:3104 EHCI.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This was broken in 7bab49fd ("lantiq: add compatible strings to dts
files"), causing for the dm200 garbled serial output during boot, and
likely other issues.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
[fix the compat string of the P2601HNFX as well]
Signed-off-by: Mathias Kresin <dev@kresin.me>
That patch fixes handling SPI messages with two writing transfers. It's
important when using e.g. by m25p80 driver which uses one transfer for
opcode and another one for data.
Thanks to that fix we can now drop m25p80 workaround patch. It means one
less hack and also a better flash writing performance as there is no
more data buf copying.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
A lot of 1U x86_64 servers have NVMe support, which is lower-power
and higher speed than SSD or CFast drives, etc. The drivers
required to make this work are trivial.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Remove a stray -Wp left in host_c_flags causing build failures for newer
4.14 versions.
Reported-by: Michael Marley <michael@michaelmarley.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Advantages:
- preserves existing partition layout on the sd-card.
Only the boot and rootfs partition will be overwritten.
Please note that sysupgrade will refuse to upgrade, if the existing
installation has an incompatible partition layout. Future changes
to the bootfs and/or rootfs partition size will likely cause breakage
to the sysupgrade procedure. In these cases, the ext4-sdcard.img.gz
will have to be written to the sdcard manually.
Please don't forget to backup your configuration in this case.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Use the values populated by the generic board detect function. The
first compatible from the device tree source file will be the board
name in userspace. The model property from the device tree source file
will be the model name.
Change the board name where used in the userspace and drop the target
specific board detect, to use the generic one.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds the compatible string for the various RPIs from
4.14 upstream.
Note: The 4.14 upstream does not include the compute modules.
If the CM* would just house the SoC, it could in theory use the
"raw" chip compatible string. However, these CM boards also come
with RAM and eMMC. So they have to have a proper comaptible.
For now, "raspberrypi,compute-module-{1|3}" will be good enough.
Note2: The original CM was renamed to CM1 when CM3 was released.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch converts all the raspberrypi images to utilize
the common metadata-based image verification.
Note: the CM1 and CM3 currently use the same "rpi-cm"
boardname.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Commit c312cef223 ("ar71xx: spi-rb4xx fix.") replaced the clk_enable() call
with clk_prepare_enable() to meet the common clock framework requirements.
However it did not change the clk_disable() call in the error patch which
thus leads to imbalance.
Fix the code by using the correct counterpart of clk_prepare_enable() in both
places.
Fixes: c312cef223 ("ar71xx: spi-rb4xx fix.")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
A few UBI messages lacks the trailing newline character which
leads to ugly lines in the bootlog like this:
[ 6.649159] UBI error: no valid UBI magic found inside mtd6[ 6.667751] Freeing unused kernel memory: 2196K
Add a newline character to the end of the messages to fix it.
After the fix the line from above looks better in the log:
[ 6.609182] UBI error: no valid UBI magic found inside mtd6
[ 6.627599] Freeing unused kernel memory: 2132K
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
A few UBI messages lacks the trailing newline character which
leads to ugly lines in the bootlog like this:
[ 6.649159] UBI error: no valid UBI magic found inside mtd6[ 6.667751] Freeing unused kernel memory: 2196K
Add a newline character to the end of the messages to fix it.
After the fix the line from above looks better in the log:
[ 6.609182] UBI error: no valid UBI magic found inside mtd6
[ 6.627599] Freeing unused kernel memory: 2132K
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
A few UBI messages lacks the trailing newline character which
leads to ugly lines in the bootlog like this:
[ 6.649159] UBI error: no valid UBI magic found inside mtd6[ 6.667751] Freeing unused kernel memory: 2196K
Add a newline character to the end of the messages to fix it.
After the fix the line from above looks better in the log:
[ 6.609182] UBI error: no valid UBI magic found inside mtd6
[ 6.627599] Freeing unused kernel memory: 2132K
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The value DSL_ChipSetHWVersion is fetched from the dsl frontend
via the dsl_control service, but not really provided by the dsl
frontend firmware and for now always "UNKNOWN".
The lantiq support told us that this information wouldn't be
provided in the foreseeable future, so let's remove this
useless "UNKNOWN" information.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Use a more appropriate compatible string. Fix the wireless led GPIO and
add the default wireless trigger. Use the wireless LED for boot state
indication as well.
Remove the GPIO pinmux for pins not exposed on the board.
Signed-off-by: Mathias Kresin <dev@kresin.me>
TP-Link TL-MR3420 v5 are simple N300 router with
5-port FE switch and non-detachable antennas.
Its very similar to TP-Link TL-WR841N V13.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- USB 2.0 Port
- UART (J1) header on PCB (115200 8n1)
- 8x LED, 2x button, power input switch
Flash instruction:
The only way to flash LEDE image in mr3420v5 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "lede-ramips-mt7628-tplink_tl-mr3420-v5-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
Move common tplink image build code into own recipe. Include the common
parts instead of including a full build recipe and overwriting former set
varaibles.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support for the MikroTik RouterBOARD 921GS-5HPacD r2
(mANTBox 15s), an outdoor sector antenna with a built-in 802.11ac
wireless router. Additionally, it adds a new profile for devices with
>= 128 MB NAND flash and 802.11ac to the ar71xx/mikrotik subtarget.
See https://mikrotik.com/product/RB921GS-5HPacD-15S for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9558 (720 MHz)
- RAM: 128 MB
- Storage: 128 MB NAND
- Wireless: external QCA9822 802.11a/ac 2x2:2
- Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE in
- SFP: 1x host
Working:
- Board/system detection
- NAND storage detection
- Wireless
- Ethernet
- 1x user LED
- Reset button
- Sysupgrade
Untested:
- SFP cage (probably not working)
Installation:
- Boot initramfs image via TFTP and then flash sysupgrade image
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Apply code from commits 9e1bc27e6d
(ar71xx: Fix UBIFS work on Mikrotik RB95x devices) and
665bb27499 (ar71xx: fix invalid pointer
dereference in rb95x_nand_scan_fixup()) to RB92x devices too.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This patch converts all apm821xx devices to the device-tree
board-detection method. All instances of the legacy
boardnames (mbl,mr24,...) are converted to "vendor,device"
identifier.
The custom board-detection code in apm821xx.sh is removed as
it no longer serves any purpose.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch enables metadata-supported image verification
for all apm821xx supported devices. Since this method comes
with a built-in image verification tool (fwtool), the previous
image checks can be removed.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Currently, the device name handle does not include the
manufacturer. This can make it hard do differentiate
between products from different vendors that have the
same product name. As the handle is used to derive
the image name.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch rename all the DT source files in order to
match upstream's "manufacturer-device.dts" format.
Please note that the DEVICE_DTB isn't changed. This is
because the u-boot of the MyBook Live defines the
fdt_file variable to be "apollo3g/apollo3g.dtb".
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Meraki choose to use their product's codename as the main
compatible string. Mathias Kresin commented that this is
a poor choice as this will confuse the users and devs once
the device-tree compatible is used for board-detection and
possible the image name.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch appends the "apm,bluestone" or "amcc,apollo3g"
machine compatible string to the current device tree source.
Please note that unlike other archs the PPC DT code does
not regard the machine's compatible string as a priority
list. This is explained in the kernel's usage-model.txt as follows:
"PowerPC uses a slightly different scheme where it calls the .probe()
hook from each machine_desc, and the first one returning TRUE is used.
However, this approach does not take into account the priority of the
compatible list, and probably should be avoided for new architecture
support."
For this reason, the "apm,bluestone" compatible string can't be
added to the WNDR4700. As otherwise the target specific pci
fix-up code will get ignored and this causes the ath9k WIFI
to not get initialized.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch sets the BOARD_NAME variable on each affected
apm821xx device. The existing DEVICE_PROFILE and
DEVICE_NAME assignments are deprecated as they no longer
serve any purpose.
The BOARD_NAME variable is used by the sysupgrade-tar
method to specifiy a directory overwrite for the
sysupgrade-$dir directory in the generated tar file.
Keeping the original boardname in this context will be
necessary for targets that utilize the sysupgrade-tar
method. Otherwise, sysupgrade on an previous installation
will not recognize the newly generated images.
This step is necessary since an upcoming patch realigns
the existing shortname for a device with a proper
"manufacturer_device" identifier.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The commit 87b668765e
("image: when using the new image build code, gzip ext4 images by default")
forced that all targets that select the ext4 as the root filesystem
to always compress the generated rootfs. This is fine, but this method
doesn't not allow to append the metadata on a per-target base.
Therefore this patch changes the rootfs image production rule to generate
the gzip step manually. This way the metadata can be appended at a later
date.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
"PandoraBox" is not the name of the manufacturer, it's a firmware made by
the manufacturer actually. Their official English name is "D-Team".
PBR-M1 is the only one they use "PandoraBox" as a brand name. Their other
products are using "Newifi" as their trademark (including Y1 and Y1S which
used to be OEM products for Lenovo).
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Previously Newifi D2 could only use PandoraBox M1's firmware.
It works fine, but LED GPIO is different.
As a result, a separated DTS file for this device should be implemented.
Hardware spec:
* CPU: MTK MT7621A
* RAM: 512MB
* ROM: 32MB SPI Flash
* WiFi: MTK MT7603+MT7612
* Button: 2 buttons (reset, wps)
* LED: 3 single-color LEDs (USB, WiFi 2.4GHz, WiFi 5GHz) &
2 dual-color LEDs (Power, Internet)
* Ethernet: 5 ports, 4 LAN + 1 WAN
Installation method:
Same as Newifi D1, users may need to request unlock code from the device
manufacturer. Otherwise, a SPI flash programmer may be necessary to get
the firmware flashed. After the device is unlocked, press and hold reset
button before power cable plugs in. Then go to http://192.168.1.1 to
upload and flash the firmware package.
Signed-off-by: Jackson Ming Hu <huming2207@gmail.com>
The VAR11N-300 is a tiny wireless-N device with a hardwired Ethernet
cable, one extra Ethernet port, and an internal antenna, based on the
MediaTek MT7620n chipset.
Specs:
- MT7620n WiSoC @ 600MHz
- 32 MB SDRAM
- 4 MB SPI flash
- 2T2R 2.4GHz WiFi-N
- 1 attached 10/100 Ethernet cable (LAN)
- 1 10/100 Ethernet port (WAN)
- 1 attached USB / barrel 5vdc power cable
- 5 LEDs (see notes below)
- 1 reset button
- 1 UART (3 pads on board)
Installation:
The stock firmware does not support uploading new firmware directly,
only checking the manufacturer's site for updates. This process may be
possible to spoof, but the update check uses some kind of homebrew
encryption that I didn't investigate. Instead, you can install via a
backdoor:
1. Set up a TFTP server to serve the firmware binary
(lede-ramips-mt7620-var11n-300-squashfs-sysupgrade.bin)
2. Factory reset the device by holding the reset button for a few
seconds.
3. Open the web interface (default IP: 192.168.253.254)
4. Log in with the "super admin" credentials: username `vonets`,
password `vonets26642519`.
5. On the "Operative Status" page, click the text "System Uptime", then
quickly click the uptime value.
6. If successful, an alert dialog will appear reading "Ated start", and
the device will now accept telnet connections. If the alert does not
appear, repeat step 5 until it works (the timing is a bit tricky).
7. Telnet to the device using credentials "admin / admin"
8. Retrieve the firmware binary from the tftp server: `tftp -l lede.bin
-r lede-ramips-mt7620-var11n-300-squashfs-sysupgrade.bin -g
<tftp-server-ip>`
9. Write the firmware to flash: `mtd_write write lede.bin /dev/mtd4`
10. Reboot
Tested:
- LAN / WAN ethernet
- WiFi
- LAN / WAN / status LED GPIOs (see notes below)
- Reset button
- Sysupgrade
Notes:
LEDs:
The board has 5 LEDs - two green LEDs for LAN / WAN activity, one blue
LED for WiFi, and a pair of "status" LEDs connected to the same GPIO
(the blue LED lights when the GPIO is low, and the green when it's
high). I was unable to determine how to operate the WiFi LED, as it
does not appear to be controlled by a GPIO directly.
Recovery:
The default U-boot installation will only boot from flash due to a
missing environment block. I generated a valid 4KB env block using
U-boot's `fw_setenv` tool and wrote it to flash at 0x30000 using an
external programmer. After this, it was possible to enter the U-boot
commandline interface and download a new image via TFTP (`tftpboot
81b00000 <image-filename>`), but while I could boot this image
sucessfully (`bootm`), writing it to flash (`cp.linux`) just corrupted
the flash chip. The sysupgrade file can be written to flash at 0x50000
using an external programmer.
Signed-off-by: Andrew Crawley <acrawley@gmail.com>
Add a helper variable which contains the boardname separated from the
vendor name. It allows to switch to a device tree compatible string
based boardname, by keeping the $board:colour:function syntax in
scripts handling/adding config for LEDs.
Boards not using the device tree compatible string as based boardname
are unaffected by the change, since none of them uses a comma in the
boardname.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use <manufacturer>_<modelname> as image name for board using the
devicetree compat string as boardname.
Replace the underline of the device define, to keep the SUPPORTED_DEVICES
in sync with a devicetree compat string based boardname.
Override the default SUPPORTED_DEVICES for board which are having an
userspace boardname with an underline.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The LinkIt Smart 7688/LinkIt Smart 7688 Duo are identical beside the
extra ATmega32U4 - accessible via UART - on the the Duo.
Since all relevant hardware is identical, drop the Duo special handling
in userspace.
Signed-off-by: Mathias Kresin <dev@kresin.me>
If we need to set the initial output value to GPIOF_OUT_INIT_HIGH (1) to
enable something, the pin is ACTIVE_HIGH. The same applies to
GPIOF_OUT_INIT_LOW (0) and ACTIVE_LOW.
Signed-off-by: Mathias Kresin <dev@kresin.me>
In the stock firmware both eth0 and eth1 are set to br-lan,
add this behavior to our images.
Fixes: FS#1084
Signed-off-by: Marty E. Plummer <hanetzer@protonmail.com>
The status led part was missed when changing the board name to *-nor.
Fixes: e12c72bb52 ("brcm63xx: Add Sercomm AD1018 support")
Reported-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Use <manufacturer>_<modelname> as image name.
Use the BOARD_NAME variable to ensure that the former used boardname is
still used as the subdirectory name for the sysupgrade-tar image, to
not break sysupgrade from earlier versions.
While at it, normalise the image filenames by using only lower case
characters and bin as file extension for sysupgrade images.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the first compatible string as board name in userspace. Add the new
board name as well as the former used board name to the image metadata
to keep compatibilty with already deployed installations.
Don't add the former used boardname for boards which exists only in
master or evaluation boards.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This adds basic support for kernel 4.14, this was tested in qemu only.
The subtarget configuration was refresh with kernel 4.14 and the
options needed to make it compile on kernel 4.9 were added manually.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel 4.14 kmod-bluetooth depends on kmod-crypto-ecdh, add
kmod-crypto-ecdh to LEDE.
Both packages also depend on the kmod-crypto-kpp package. To build this
we have to fix the dependency of CRYPTO_ECDH which has a typo.
This patch is already accepted upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds initial support for kernel 4.14 based on the patches for
kernel 4.9.
In the configuration I deactivated some of the new possible security
features like:
CONFIG_REFCOUNT_FULL
CONFIG_SLAB_FREELIST_HARDENED
CONFIG_SOFTLOCKUP_DETECTOR
CONFIG_WARN_ALL_UNSEEDED_RANDOM
And these overlay FS options are also deactivated:
CONFIG_OVERLAY_FS_INDEX
CONFIG_OVERLAY_FS_REDIRECT_DIR
I activated this:
CONFIG_FORTIFY_SOURCE
CONFIG_POSIX_TIMERS
CONFIG_SLAB_MERGE_DEFAULT
CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED
I am not sure if I did the porting correct for the following patches:
target/linux/generic/backport-4.14/020-backport_netfilter_rtcache.patch
target/linux/generic/hack-4.14/220-gc_sections.patch
target/linux/generic/hack-4.14/321-powerpc_crtsavres_prereq.patch
target/linux/generic/pending-4.14/305-mips_module_reloc.patch
target/linux/generic/pending-4.14/611-netfilter_match_bypass_default_table.patch
target/linux/generic/pending-4.14/680-NET-skip-GRO-for-foreign-MAC-addresses.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Just refresh the kernel configuration, some options are removed because
they are now in the generic kernel configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These are taken from the x86 target and should make support kernel 4.9
and 4.14 in the x86 target easier.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cover temperature sensors for all mainstream 64-bit processors, including
AMD 10h and 15h families, Intel iCore, Xeon, Atom, and Via Nano. Also
add CPUID support for user-space applications to detect CPU type.
Include the on-chip sensors for 64-bit CPU's in the generic profile
in case someone builds a 32-bit kernel to run on a Xeon SoC, etc.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Backport the mdio-bus reset gpio support from 4.12 and use it instead
of toggling the reset ourself.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Add support for the Sercomm AD1018 router
This a BCM6328 based board, 128 MB RAM, 128 MiB NAND flash,
with an onboard BCM43217 wifi, 4 ethernet ports and 1 USB
host port (not soldered). The board also has an FXS chip (Si32177)
connected via SPI (SS2#), without support in LEDE.
Since NAND flash chips aren't still supported in brcm63xx, the
support is for now added to work only with SPI flash chips. Therefore
hardware modding, soldering a new SPI flash chip, is required
to make the board work with LEDE (tested and working OK).
The flash at dts is intentionally left without partitioning to let
the user choose a NOR chip of any size (8, 16 or 32 MB).
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
[jonas.gorski: renamed ad1018 to ad1018-nor to signify the modification]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Since Linux 4.6, mtd->priv no longer points to the NAND specific
structure. Under 4.9 it contains NULL, thus using it to access
chip->options causes an invalid pointer dereference (FS#1200).
Update the code to use the mtd_to_nand() helper under 4.9 to obtain
the address of the chip specific data.
Fixes: 7bbf4117c6 ("ar71xx: Add kernel 4.9 support")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Since Linux 4.6, mtd->priv no longer points to the NAND specific
structure. Under 4.9 it contains NULL, thus using it to access
the fields of the nand_chip structure causes an invalid pointer
dereference.
Update the code to use the mtd_to_nand() helper under 4.9 to obtain
the address of the chip specific data.
Compile tested only.
Fixes: 7bbf4117c6 ("ar71xx: Add kernel 4.9 support")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Tested-by: Christian Lamparter <chunkeey@gmail.com>
When mtdsplit_minor.c is compiled under Linux 4.4, the compiler
drops the following warning:
CC drivers/mtd/mtdsplit/mtdsplit_minor.o
drivers/mtd/mtdsplit/mtdsplit_minor.c:106:14: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
.parse_fn = mtdsplit_parse_minor,
^
drivers/mtd/mtdsplit/mtdsplit_minor.c:106:14: note: (near initialization for 'mtdsplit_minor_parser.parse_fn')
The second parameter of the parser function must not have a 'const'
qualifier in 4.4. The 001-mtdsplit_backport.patch removes the qualifier
from other partition parsers. Update it to handle mtdsplit_minor.c as
well.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
This reverts commit 256990cbc0.
this commit caused a compile error
"TL_WR1043_V5_GPIO_LED_WANORANGE" is undefined.
Signed-off-by: John Crispin <john@phrozen.org>
Add missing definitions for the orange WAN LED on the TL-WR1043N(D) v4 and
v5. Minor format correction on a constant for consistency.
Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
This patch fixes the switch port numbering on Mikrotik RB951Ui-2nD (hAP).
Also fixes the switch port numbering shown on LuCI for Mikrotik RB493G.
Signed-off-by: João Chaínho <joaochainho@gmail.com>
Advantages:
- preserves existing partition layout. On the hard-drive.
Only the boot and rootfs partition will be overwritten.
Disadvantages:
- The upgrade process takes much longer to run.
from 2-3 seconds to 15-25 seconds.
Please note that sysupgrade will refuse to upgrade, if the existing
installation has an incompatible partition layout. Future changes
to the bootfs and/or rootfs partition size will likely cause breakage
to the sysupgrade procedure. In these cases, the ext4-rootfs.img.gz
has to be written manually onto the disk. Please don't forget to backup
your configuration in this cases.
Note2: This patch requires
"base-files: upgrade: make get_partitions() endian agnostic"
Note3: If your current installation does not host the two
changes, sysupgrading will wipe the existing partition
layout. Don't forget to backup your data!
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Please note that users with a Netgear WNDR4700
will need to update the device-tree partition
manually.
For instructions, please refere to commit 49856a4bb5
("apm821xx: make it possible to update the dtb partition on the WNDR4700")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Lantiq and IPQ806X (which includes IPQ40XX) both define the
same custom function {ipq806x|lantiq}_get_dt_led.
This patch moves the function into the base-file package at
lib/functions/leds.sh to make it more accessible for other
targets as well.
Cc: Mathias Kresin <dev@kresin.me>
Cc: John Crispin <john@phrozen.org>
Cc: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The bcm6368 pinctrl driver passed the wrong variable to
devm_regmap_field_alloc, causing it to blow up when later trying to
access the field.
Fixes#1211.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
For an unknown reason gcc tries to link in crti.o when building with a
glibc toolchain (this does not happen with other targets). Prevent this
by telling gcc explicitly to not do that.
Fixes the following build error:
/home/jonas/git/lede/staging_dir/toolchain-mips_24kc_gcc-5.5.0_glibc/lib/gcc/mips-openwrt-linux-gnu/5.5.0/../../../../mips-openwrt-linux-gnu/lib/crti.o: In function `_init':
(.init+0x18): relocation truncated to fit: R_MIPS_GOT16 against `__gmon_start__'
/home/jonas/git/lede/staging_dir/toolchain-mips_24kc_gcc-5.5.0_glibc/lib/gcc/mips-openwrt-linux-gnu/5.5.0/../../../../mips-openwrt-linux-gnu/lib/crti.o: In function `_init':
(.init+0x28): relocation truncated to fit: R_MIPS_CALL16 against `__gmon_start__'
collect2: error: ld returned 1 exit status
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This will avoid some conflicts when doing a git rebase or merge,
specially when adding support to a new device.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
[drop brcm47xx changes which rename the images]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Recent RouterBOOT version (at least version 3.41 on RB911G-5HPacD)
use "Board=" kernel parameter instead of "board=" to pass the board
name to the kernel. Due to this change the board detection code is
not working on the devices shipped with the new RouterBOOT version.
Because the kernel is unable to identify these boards they become
unusable despite that they are supported by the current code.
Update the prom_init code to convert the 'Board' kernel parameter to
'board'. After this change, the board detection works also with the
new RouterBOOT versions.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The target name does not need to included a revision
if all revisions are supported.
This target supports all revisions (v1, v2, v2.1).
Signed-off-by: Moritz Warning <moritzwarning@web.de>
[Keep the version numbers in the device title, it doesn't harm]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Remove the WW suffix, everything without a region suffix is world wide
anyway.
While at it, normalise the image filenames by using only lower case
characters.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Users are confused which image type they should use and there are more
drawbacks than adavantages in using a r/w ubifs rootfs in constrast to
a read-only squashfs rootfs like:
- less available free flash space due to better compression of squashfs
images
- no support for factory reset due to r/w filesystem
- possibility to break failsafe due to r/w filesystem
Therefore, drop support for r/w ubifs rootfs images.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The boardname isn't used any longer to find the subdirectory in the
sysupgrade tar archive, which makes this override useless.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Qualcomm claims this reduces cache misses. Original commit message below:
From: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Date: Tue, 11 Jun 2013 12:18:46 -0500
Subject: [ag71xx] reduce NAPI weight
In an attempt to increase our cache warmth, we are decreasing NAPI.
This increases the warmth of the reused SKBs.
Signed-off-by: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The motivation for this was misguided. It turns out tuning the NAPI weight could be useful for testing purposes. Therefore reverting.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This commit fixes LAN Port 1 not transferring data in case no
other LAN Port has active link-state on TP-Link Archer C58/C59.
Signed-off-by: David Bauer <mail@david-bauer.net>
This is a variant of the MT7620N-based Asus routers.
Specifications:
- MT7620N (580 MHz)
- 32 MB RAM
- 8 MB Flash
- 5x 10/100Mbps Ethernet (built-in switch)
- 2.4 GHz WLAN
- 2x external, non-detachable antennas
- UART (J2) header on PCB (115200 8n1)
Flash instructions:
1. Configure PC with static IP 192.168.1.75/24
2. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds. All 4 LEDs will
start to blink, which is when the router will accept firmware files via TFTP.
No known limitations on firmware filenames, just send it with a TFTP client
to 192.168.1.1.
3. Router will download file from server, write it to flash and reboot.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This commit adds missing the GPIO key used as reset button.
Nexx WT1520 has a GPIO key for factory reset, but it's not defined in
WT1520.dtsi and cannot use it.
Drop the UART (full) from the device tree source file, it was never
used for this board. Adjust the kernel bootargs accordingly.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[add note about dropped UART (full) to the commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
There are multiple problems on the A64 SoC with the older drivers which
are fixed in the upstream kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add pinmuxes defined by some board which are including the dtsi files
to the dtsi files itself. Allows to reduce duplication.
Signed-off-by: Mathias Kresin <dev@kresin.me>
According to the datasheet the REFCLK pin is shared with GPIO#37 and
the PERST pin is shared with GPIO#36.
While at it fix a typo inside the pinmux setup code. The function is called
refclk and not reclk.
Update device tree source files accordingly.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add kmod-sound-core, it is a dependency of kmod-sound-mt7620 and will
not be autoselected.
Remove kmod-i2c-core, it will be autoselected by kmod-i2c-ralink.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Setting the pins of the UARTF group to GPIO+I2S at the time the I2C
driver loads is to late for the wps GPIO button.
The gpio-keys driver fails to load since the pin used by the wps button
is not yet set to GPIO. The wps button with the rfkill keycode is
essential for this wireless only board.
Add the missing sound and I2C kernel modules corresponding to the
device nodes.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The advantage is that we don't have to specify max TRX size anymore and
otrx doesn't allocate a buffer of that size. It saves us allocating
32 MiB for every image we generate.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Backported devicetree from Kernel 4.13 with some additions
to enable Ethernet and WiFi module
The following features are working:
- Ethernet
- WiFi
- eMMC and microSD slot
- USB ports
The following features are not working:
* Bluetooth
NanoPi M1 Plus key features
- SoC: Allwinner H3, Quad-core Cortex-A7@1.2GHz
- RAM: 1GB DDR3
- eMMC: 8GB
- microSD slot
- Ethernet 10/100/1000M
- Wifi: AP6212
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
D-Link DIR-330 is clone of ASUS WL500GP2, by default conf the WAN port is
eth1, it's not working cus eth1 not soldered and wan port function
performs 5th port of the switch.
Signed-off-by: Antony Black <gtrtfm@gmail.com>
Currently local TCP performance on wifi devices can be limited because
the TSQ (TCP Small Queues) code is tuned for wired ethernet latencies.
With this patch drivers can increase the amount of local buffering to
allow TCP to trigger larger aggregation sizes
This commit is modified from the upstream version to allow #ifdef based
backport feature detection
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a variant of the ZBT WG3526 with a few minor modifications.
The wifi chips are swapped, and there is no GPIO controllable status
LED. There is also no SATA port.
Specifications:
- MT7621AT (880 MHz)
- 512 MB RAM
- 16 MB Flash (SPI NOR)
- 5x 1Gbps Ethernet (built-in switch)
- MT7612E 802.11ac 5 GHz WLAN
- MT7603E 802.11n 2.4 GHz WLAN
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The IRQ controller can only set the affinity to a single CPU. Update the
mask in the controller data.
Suggested-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
TP-Link TL-WR802N v1 and v2 are set up with almost same configuration in
the mach-files. Merge the mach-files of these devices.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
TP-Link TL-WR1043N v5 appears to be identical to the TL-WR1043ND v4,
except that the USB port has been removed and there is no longer a
removable antenna option.
The software is more in line with the Archer series in that it uses a
nested bootloader scheme.
Specifications:
- QCA9563 at 775 MHz
- 64 MB RAM
- 16 MB flash
- 3 (non-detachable) Antennas / 450 Mbit
- 1x/4x WAN/LAN Gbps Ethernet (QCA8337)
- reset and Wi-Fi buttons
Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
The TL-WA901ND v5 has the same hardware as v4, although the PCB has
a different layout. Installation from factory is done via TFTP.
(rename -factory image to wa901ndv4_tp_recovery.bin for tftp)
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
This patch adds support for the MikroTik RouterBOARD mAP 2nD
https://mikrotik.com/product/RBmAP2nD
Specifications:
- SoC: Qualcomm QCA9531 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: builtin QCA9531, 2x2:2
- Ethernet: 2x100M (802.3af/at POE in and passive POE out on ETH2)
- USB: microUSB type AB port
This patch adds missing code to fully support mAP. Machfile already
contained configuration for mAP 2nD, but device specific configuration
like LEDs etc., was missing.
Note: The POE LED works but doesn't turn on when POE passthrough is
enabled, despite being configured with GPIO trigger.
Installation
1. Login to the Mikrotik WebUI to backup your licence keys
2. Setup a DHCP/BOOTP server with:
- DHCP-Option 66 (TFTP server name) pointing to a local TFTP
server within the same subnet of the DHCP range
- DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
of the to be booted image
3. Connect the port labeled internet to your local network
4. Keep the reset button pushed down and power on the board
The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started LEDE via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.
Revert to RouterOS
Use the "rbcfg" package on in LEDE:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply
Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.
Click on install again.
In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Ubiquiti UniFi APs just have eth0. Until now, the setup script fell
through to the default case and configured the (not present) eth1 as
WAN with DHCP.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
This patch adds support for the MikroTik RouterBOARD wAP
https://mikrotik.com/product/RBwAP2nD
Specifications:
- SoC: Qualcomm QCA9533 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: built-in QCA9533, 2x2:2
- Ethernet: 1x100M (802.3af/at POE in)
This patch adds missing code to fully support wAP. Machfile already
contained configuration for wAP 2nD but device specific configuration
like LEDs etc. was missing.
Installation:
1. Login to the Mikrotik WebUI to backup your licence keys
2. Setup a DHCP/BOOTP server with:
- DHCP-Option 66 (TFTP server name) pointing to a local TFTP
server within the same subnet of the DHCP range
- DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
of the to be booted image
3. Connect the port labeled internet to your local network
4. Keep the reset button pushed down and power on the board
The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started LEDE via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.
Revert to RouterOS
Use the "rbcfg" package on in LEDE:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply
Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.
Click on install again.
In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Wallys DR342 is a 5 GHz, 2T2R AP/CPE board based on Atheros AR9342.
Short specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 1x Gbps Ethernet (AR8035) with passive PoE support (24-56 V)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 5 GHz with external FEM (SKY85728-11), up to 30 dBm
- 2x MMCX connectors
- miniPCIe connector with PCIe and USB 2.0 buses
- optional miniSIM slot
- 7x LED, 1x button
- UART, (E)JTAG and LED headers
- 1x DC jack for main power (12-56 V)
Flash instruction (do it under U-Boot, using UART):
1. tftp 0x82000000 lede-ar71xx-generic-dr342-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
UniElec U7628-01 is a router platform board based on MediaTek MT7628AN.
The device has the following specifications:
- MT7628AN (580MHz)
- 64/128/256 MB of RAM (DDR2)
- 8/16 MB of flash (SPI NOR)
- 5x 10/100 Mbps Ethernet (MT7628 built-in switch)
- 1x 2T2R 2.4 GHz Wi-Fi (MT7628)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 1x miniSIM slot
- 1x microSD slot
- 1x USB 2.0 port
- 7x single-color LEDs (GPIO-controlled)
- 1x bi-color LED (green GPIO-controlled, red -> LED_WLAN# in miniPCIe)
- 1x reset button
- 1x UART header (4-pins)
- 1x SDXC/GPIO header (10-pins, connected with microSD slot)
- 1x DC jack for main power (12 V)
The following has been tested and is working:
- Ethernet switch
- miniPCIe slot (tested with modem and Wi-Fi card)
- miniSIM slot
- sysupgrade
- reset button
- USB 2.0 port*
Due to a missing driver (MMC over GPIO) this is not supported:
- microSD card reader
* Warning:
USB buses in miniPCIe and regular A-type socket are connected together,
without any proper analog switch or USB HUB.
Installation:
This board might come with a different firmware versions (MediaTek SDK,
PandoraBox, Padavan, etc.). If your board comes with PandoraBox, you can
install LEDE using sysupgrade. Just SSH to the router and perform forced
sysupgrade (due to a board name mismatch). The default IP of this board
should be: 192.168.1.1 and username/password: root/admin. In case of a
different firmware, you can use web based recovery described below.
Use the following command to perform the sysupgrade (for the 128MB
RAM/16MB flash version):
sysupgrade -n -F lede-ramips-mt76x8-u7628-01-128M-16M-squashfs-sysupgrade.bin
Recovery:
This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.
SDXC/GPIO header (J3):
1. SDXC_D3 / I2C_SCLK
2. SDXC_D2 / I2C_SD
3. SDXC_D1 / I2S_DI
4. SDXC_D0 / I2S_WS
5. SDXC_CMD / I2S_CLK
6. SDXC_CLK / GPIO0
7. SDXC_CD / UART_RXD1
8. UART_TXD1
9. 3V3
10. GND
Other notes:
1. The board is available with different amounts of RAM and flash. We
have only added support for the 128/16 MB configuration, as that seems
to be the default. However, all the required infrastructure is in place
for making support for the other configurations easy.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
UniElec U7621-06 is a router platform board based on MediaTek MT7621AT.
The device has the following specifications:
- MT7621AT (880 MHz)
- 256/512 MB of RAM (DDR3)
- 8/16/32/64 MB of FLASH (SPI NOR)
- 5x 1 Gbps Ethernet (MT7621 built-in switch)
- 1x ASMedia ASM1061 (for mSATA and SATA)
- 2x miniPCIe slots (PCIe bus only)
- 1x mSATA slot (with USB 2.0 bus for modem)
- 1x SATA
- 1x miniSIM slot
- 1x microSD slot
- 1x USB 3.0
- 12x LEDs (3 GPIO-controlled)
- 1x reset button
- 1x UART header (4-pins)
- 1x GPIO header (30-pins)
- 1x FPC connector for LEDs (20-pin, 0.5 mm pitch)
- 1x DC jack for main power (12 V)
The following has been tested and is working:
- Ethernet switch
- miniPCIe slots (tested with Wi-Fi cards)
- mSATA slot (tested with modem and mSATA drive)
- miniSIM slot
- sysupgrade
- reset button
- microSD slot
Installation:
This board might come with a different firmware versions (MediaTek SDK,
PandoraBox, Padavan, etc.). If your board comes with PandoraBox, you can
install LEDE using sysupgrade. Just SSH to the router and perform forced
sysupgrade (due to a board name mismatch). The default IP of this board
should be: 192.168.1.1 and username/password: root/admin. In case of a
different firmware, you can use web based recovery described below.
Use the following command to perform the sysupgrade (for the 256MB
RAM/16MB flash version):
sysupgrade -n -F lede-ramips-mt7621-u7621-06-256M-16M-squashfs-sysupgrade.bin
Recovery:
This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.
LEDs list (top row, left to right):
- LED_WWAN# (connected with pin 42 in LTE/mSATA slot)
- Power (connected directly to 3V3)
- CTS2_N (GPIO10, configured as "status" LED)
- TXD2 (GPIO11, configured as "led4", without default trigger)
- RXD2 (GPIO12, configured as "led5", without default trigger)
- LED_WLAN# (connected with pin 44 in wifi0 slot)
LEDs list (bottom row, left to right):
- ESW_P0_LED_0
- ESW_P1_LED_0
- ESW_P2_LED_0
- ESW_P3_LED_0
- ESW_P4_LED_0
- LED_WLAN# (connected with pin 44 in wifi1 slot)
Other notes:
1. The board is available with different amounts of RAM and flash. We
have only added support for the 256/16 MB configuration, as that seems
to be the default. However, all the required infrastructure is in place
for making support for the other configurations easy.
2. The manufacturer offers five different wireless cards with MediaTek
chipsets, based on MT76x2, MT7603 and MT7615. Images of the board all
show that the miniPCIe slots are dedicated to specific Wi-Fi cards.
However, the slots are generic.
3. All boards we got access to had the same EEPROM content. The default
firmware reads the Ethernet MAC from offset 0xe000 in factory partition.
This offset only contains 0xffs, so a random MAC will be generated on
every boot of the router. There is a valid MAC stored at offset 0xe006
and this MAC is shown as the WAN MAC in the bootloader. However, it is
the same on all boards we have checked. Based on information provided
by the vendor, all boards sold in small quantities are considered more
as samples for development purposes.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
This increases kernel partition size and fixes rootfs (file-system)
partition size on TP-Link RE450 v1. Also, while we are at it, switch
from statically defined kernel and rootfs partitions in kernel cmdline
to "tplink-fw" mtd splitter.
Fixes: FS#1072.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This patch increases kernel partition size and re-enables image
generation for below TP-Link boards:
- archer-c58-v1
- archer-c60-v1
- tl-wr902ac-v1
- tl-wr942n-v1
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[commit message and title reworded]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
There was a typo in module.mk for pfe module autoload.
This patch is to fix this and remove useless rc.local
which was for loading pfe module.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The QorIQ FRDM-LS1012A Board is an ultra-low-cost
development platform for QorIQ LS1012A Series Network
Processors built on ARM Cortex-A53 processor.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to add PPA (The Primary Protected Application)
package and also enable it for all layerscape devices.
LSDK github provides ppa source code git tree, but it
only could be compiled with 64-bit toolchain. For 32-bit
devices, there was no method to use it.
https://github.com/qoriq-open-source/ppa-generic
This patch is to directly use a private ppa binary tree for
both 32-bit and 64-bit devices.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to use ppfe git tree on LSDK github
instead of private git tree, and support the latest
ppfe on ls1012ardb.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Some new options were introduced by kernel patches.
And some options should be removed/added.
The config-4.9 should be updated accordingly.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Updated kernel patches to align layerscape kernel
with latest LSDK linux (LSDK-17.09-update-103017-V4.9 tag).
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Default profile had to enable many packages for all devices
support. This made these packages still enabled when built
for single device. This patch is to remove default profile.
For multiple devices build, it's proper to build with multiple
devices profile.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
A previous patch disaggregated kernel patch 601 intending to
reverse the ndo_get_stats64 change, but it also dropped
many other changes without a reason. This caused build issue
for layerscape. This patch is to fix that with below steps.
1. Reversed patch "1c4415a layerscape: reverse changes to ndo_get_stats64",
but kept kernel patch 701 which was a proper fix.
2. Reversed the ndo_get_stats64 change in kernel patch 601.
3. Renamed patch 601 (net patch) to 202 (core-linux patch). Maybe it's
more proper.
Fixes: 1c4415a679 ("layerscape: reverse changes to ndo_get_stats64")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
On the Asus RT-N16, the ports are not mapped the in the same way as
the RT-N12. It is, however, the same as the Linksys E3000v1.
Signed-off-by: Tim Thorpe <timfthorpe@gmail.com>
The memcpy of the init data relies on chip->registers to be initialized,
which only happens later in the code. Move this initialization further
down to make it work.
This was breaking PCIe/USB on some MikroTik RouterBoard devices.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The MAC addresses were not being set for LAN and WAN. This will now use the
same MAC mechanism as the rest of the target.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
TP-Link TL-WR840N v5 is simple N300 router with 5-port FE switch and
non-detachable antennas, based on MediaTek MT7628NN (aka MT7628N) WiSoC.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 1x LED (GPIO-controlled), 1x button
* LED in TL-WR840N v5 is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Orange LED is registered so you can later use it for your own purposes.
Flash instruction:
Unlike TL-WR840N v4 flashing through WEB UI works in v5.
1. Download lede-ramips-mt76x8-tl-wr840n-v5-squashfs-sysupgrade.bin image.
2. Go to 192.168.0.1
3. Flash the sysupgrade image through Firmware upgrade section of WEB UI.
4. Wait until green LED stops flashing and use the router.
Notes:
TFTP recovery is broken since TP-Link reused bootloader code for v4 and
that does not take into account only 4 MB of flash and bricks the device.
So do not use TFTP Recovery or you will have to rewrite SPI flash.
They fixed it in later GPL code,but it is unknown which version of
bootloader you have.
After manually compiling and flashing bootloader from GPL sources TFTP
recovery works properly.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The splitter ignored the rootfs offset from the header, probably
because until c1e6e61 it was invalid.
This patch fixes the splitter to use the now correct header data.
Regarding target/linux/ar71xx/files/drivers/mtd/tplinkpart.c,
this particular splitter "falls back" to the correct rootfs offset
reading and as such it doesn't need to be updated, although it will
report a kernel partition length that can be larger than the actual
length as it assumes that partition fills the entire segment up to
the rootfs partition.
Tested-by: Mathias Kresin <dev@kresin.me>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Tested-by: Henryk Heisig <hyniu@o2.pl>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
- H3 @ 1.3 GHz
- 1GiB DDR3
- 10/100Mbps Ethernet
- Realtek RTL8189ETV wifi
- 4 USB 2.0
Difference to the "Orange Pi Plus" is the lack of Gbit ethernet
and lack of onboard flash.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Current jumbo frame support code allocates rxbuffers of the maximum size
supported by the hardware (~14KB). This happens at the device open time
even if the configured MTU is lower (e.g. if it configured to standard
1500 bytes). Such behavior effectivly prevents interface start on boards
with a low ammount of RAM (e.g. WRT300N v2), since the kernel simly can
not allocates of ~0.8MB (14KB x 64).
So remove jumbo frame support for now.
Reported-by: Nerijus Baliunas <nerijus@users.sourceforge.net>
Tested-by: Nerijus Baliunas <nerijus@users.sourceforge.net>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
The patch, which adds multiphy support, adds new path for non-standard
PHYs (e.g. MV88E6060 switch IC) to avoid using kernel phy framework. All
work well except the link status traking (Duplex and Speed), which is
reseted as soon as PHY connection procedure is done. This leads to lost
of the link status of non-standard PHY, which is configured exactly in
the ixp4xx_phy_connect() function.
Move the generic reset of a link state to the ixp4xx_phy_connect()
function to the code path, which is intended for handling of a normal
PHY.
Reported-by: Nerijus Baliunas <nerijus@users.sourceforge.net>
Tested-by: Nerijus Baliunas <nerijus@users.sourceforge.net>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
The MarsBoard was a short-lived credit-card sized, extendable board with an Allwinner A10 SoC.
http://linux-sunxi.org/MarsBoard_A10
Signed-off-by: Kayo Phoenix <kayo@illumium.org>
[Forward-ported to new target layout:]
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Piotr Dymacz
Davide Fioravanti
Stijn Tintel
Matthias Schiffer
Jo-Philipp Wich
Sven Eckelmann
Sven Eckelmann
Luis Araneda
Mathias Kresin
Florian Fainelli
Rafał Miłecki
Rosen Penev
Christian Lamparter
Hauke Mehrtens
Kevin Darbyshire-Bryant
Alberto Bursi
David Bauer
Chuanhong Guo
Gabor Juhos
John Crispin
Philip Prindeville
Thomas Nixon
Vittorio Gambaletta
Jonas Gorski
Martin Schiller
Henryk Heisig
Tomasz Maciej Nowak
Roger Pueyo Centelles
Jackson Ming Hu
Andrew Crawley
Marty E. Plummer
Daniel Gonzalez Cabanelas
Sandeep Sheriker Mallikarjun
kyson Lok
Tim Thorpe
João Chaínho
Moritz Warning
Pavel Kubelun
Felix Fietkau
Zoltan HERPAI
INAGAKI Hiroshi
Lucian Cristian
Koen Vandeputte
Ted Hess
Roman Yeryomin
Antony Black
Paul Wassi
Robert Marko
Yangbo Lu
Tim Thorpe
Daniel Gimpelevich
Thibaut VARÈNE
Sergey Ryazanov
Kayo Phoenix