73b8805e78
ar71xx: fix PHY setup on TL-MR3020 ( fixes #11572 )
...
SVN-Revision: 32093
2012-06-06 17:24:12 +00:00
dc9675282e
ar71xx: add a helper function for setting up PHY4 swapping on ar933x
...
SVN-Revision: 32092
2012-06-06 17:24:09 +00:00
072bed4760
target: do not make target/*/install depend on target/*/compile - removes one redundant kernel build dir call on target/install
...
SVN-Revision: 32091
2012-06-06 17:24:05 +00:00
02ab0d3ef9
ar71xx: only build all loader images if the image builder is enabled - saves some time on make target/install
...
SVN-Revision: 32090
2012-06-06 17:24:01 +00:00
4c25e42fa8
fix alarm led color for board 96348A-122
...
SVN-Revision: 32089
2012-06-06 16:07:46 +00:00
2f63f097de
add 96348w3 board ( #10764 )
...
SVN-Revision: 32088
2012-06-06 15:45:04 +00:00
9d38989d1f
update livebox board support ( #8677 )
...
Merge most fixes from #8677 :
- add basic hardware detection of Livebox Blue 5g revisions
- register leds and gpio buttons
- fix boot address location
- properly parse mac addresses
Plus some more fixes:
- make board_livebox.c more in line with board_bcm963xx.c
SVN-Revision: 32087
2012-06-06 15:44:56 +00:00
c69a2cdfbb
fix leds naming for all bcm63xx boards
...
SVN-Revision: 32086
2012-06-06 15:44:52 +00:00
ce1d4d7ee9
kernel: make tracing support configurable
...
SVN-Revision: 32085
2012-06-06 15:25:57 +00:00
23fc737b9d
backport upstream spi-bcm63xx fixes
...
* message pump conversion
* not using stopping state
* setting spi driver mode bits
SVN-Revision: 32078
2012-06-06 13:31:33 +00:00
7b12e9e49c
backport spi message queue infrastructure
...
SVN-Revision: 32077
2012-06-06 13:31:30 +00:00
4112094dbb
increase led number in patch 301-led_count.patch
...
So that board patches are only touching board-related code
SVN-Revision: 32076
2012-06-06 13:31:24 +00:00
95e69ac4f1
clean up generic image building
...
SVN-Revision: 32065
2012-06-05 17:49:42 +00:00
9a61b249c5
fix board patches so that new boards are withing appropriate ifdef
...
Some new board definitions were added within the #ifdef CONFIG_CPU_6338
section while some other were added within #ifdef CONFIG_CPU_6345, fix this
SVN-Revision: 32060
2012-06-05 13:40:41 +00:00
5ec2209734
refresh generic patches
...
SVN-Revision: 32059
2012-06-05 13:40:38 +00:00
36c99bcc42
fix bisectability of patch 303-spi-board-info.patch
...
It uses spi_register_board_info() from linux/spi/spi.h but does not include it
explicitely.
SVN-Revision: 32058
2012-06-05 13:40:35 +00:00
a4d96aae8d
bump to 3.3.8
...
SVN-Revision: 32055
2012-06-05 06:57:51 +00:00
605012ad5d
kirkwood: reorganize target
...
SVN-Revision: 32053
2012-06-05 00:43:56 +00:00
7f00e5ffc6
uboot-envtools: update to 2012.04.01
...
SVN-Revision: 32051
2012-06-04 21:55:49 +00:00
ffea8eb913
bcm63xx: fix ethernet on 96328avng and 963281TAN
...
The internal switch did not get registered.
SVN-Revision: 32041
2012-06-04 08:35:25 +00:00
2b4ef2eafa
adds unset Kbuild symbol
...
SVN-Revision: 32026
2012-06-02 14:03:32 +00:00
f4b02b91ce
malta: remove 3.2 patches
...
SVN-Revision: 32023
2012-06-02 12:06:28 +00:00
c0c60f7bd3
malta: use common kernel config
...
SVN-Revision: 32022
2012-06-02 12:06:26 +00:00
9375e83586
xburst: add missing config symbol
...
SVN-Revision: 32021
2012-06-02 12:06:15 +00:00
76e4cd2a24
add $(SUBTARGET) to the filename if available
...
SVN-Revision: 32007
2012-05-30 18:04:15 +00:00
47ef62d1b8
adds patch to make Tantos (psb6970) switch buildable again
...
SVN-Revision: 32006
2012-05-30 17:41:28 +00:00
3fc76fb781
bcm63xx: build images for 6328 reference boards with various flash sizes
...
Build images for 96328avng and 963281TAN (untested) for three different
flash sizes: 4MB, 8MB, and 16MB.
Known issues:
* Button setup unknown, thus no fail-safe available.
* All other BCM6328 and BCM63XX issues
SVN-Revision: 32004
2012-05-30 10:27:46 +00:00
c454ba3657
bcm63xx: readd accidentially dropped network config for SPW303V
...
SVN-Revision: 32003
2012-05-30 10:27:42 +00:00
9e02593b70
generic: ar8216: add revision specific PHY fixups for AR8327
...
SVN-Revision: 32000
2012-05-29 16:39:27 +00:00
0d241e6670
generic: ar8216: replace chip_type field with chip_{ver,rev} in ar8216_priv
...
SVN-Revision: 31999
2012-05-29 16:39:26 +00:00
b2fce19a70
generic: ar8216: add chip_is_ar8{216,236,316,327} helpers
...
SVN-Revision: 31998
2012-05-29 16:39:24 +00:00
cd7ab1d30b
ar71xx: add default LED setup for the DB120 board
...
SVN-Revision: 31997
2012-05-29 16:39:23 +00:00
29a579e43a
cns21xx: use the generic uci-default functions for initial LED setup
...
SVN-Revision: 31996
2012-05-29 16:39:22 +00:00
ff74305623
lantiq: use the generic uci-default functions for initial LED setup
...
SVN-Revision: 31995
2012-05-29 16:39:21 +00:00
c81c6516de
kirkwood: use the generic uci-default functions for initial LED setup
...
SVN-Revision: 31994
2012-05-29 16:39:20 +00:00
ffbb4f88a9
ramips: use the generic uci-default functions for initial LED setup
...
SVN-Revision: 31993
2012-05-29 16:39:18 +00:00
4e40bdc190
ar71xx: use the generic uci-default functions for initial LED setup
...
SVN-Revision: 31992
2012-05-29 16:39:17 +00:00
ba3ad24514
kirkwood: use uci-defaults to configure different boards
...
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 31990
2012-05-29 16:39:15 +00:00
c71838faa1
ramips: WAN LED for D-Link DIR-300-B1
...
Add led devices for D-Link DIR-300-B1 WAN LED.
Note that the GPIO state is also ANDed with the esw switch port 4
LED state, which is why I've set the amber LED to default-on.
Closes: https://dev.openwrt.org/ticket/11326
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
[ juhosg:
- fix comment style in mach-dir-300-revb.c,
- remove the PPP specific LED setup, not everyone uses a PPP connection
on the WAN interface]
SVN-Revision: 31989
2012-05-29 16:39:03 +00:00
a9cd8446f3
ar71xx: do not override the mdio clock for ar9330. the override value (obtained from an atheros driver) seems to break ethernet functionality
...
SVN-Revision: 31956
2012-05-28 20:39:50 +00:00
367e4b3994
ar71xx: improve rx performance of the ethernet driver by using build_skb to deliver a cache-hot skb to the network stack
...
SVN-Revision: 31934
2012-05-28 02:55:59 +00:00
8039a1bbb2
ar71xx: fix MII clock settings for various chips, improves ethernet stability on AR934x
...
SVN-Revision: 31925
2012-05-27 21:02:41 +00:00
f638414fdc
kernel: fix suppressing -s for linking modules when profiling is enabled
...
SVN-Revision: 31924
2012-05-27 21:02:36 +00:00
8865f0923e
ar71xx: fix TL-WR1041 image size
...
SVN-Revision: 31923
2012-05-27 17:21:47 +00:00
1c552ba8e5
ramips: rt3883: add device registration code for the SPI controller
...
SVN-Revision: 31922
2012-05-27 17:10:00 +00:00
9c241983fc
ramips: allow to use the SPI driver on RT3662/RT3883
...
SVN-Revision: 31921
2012-05-27 17:09:58 +00:00
78a750dcce
ramips: rt3883: fix GPIO reservation for the SPI pins
...
SVN-Revision: 31920
2012-05-27 17:09:56 +00:00
0622fdd82c
ramips: rt305x: remove superfluous controller_data assignment
...
SVN-Revision: 31919
2012-05-27 17:09:52 +00:00
7f5bec0642
ramips: make rt2x00 firmware extraction quiet
...
SVN-Revision: 31918
2012-05-27 17:09:50 +00:00
86dad96fd0
generic: rtl8367: rename a misnamed variable
...
SVN-Revision: 31917
2012-05-27 17:09:47 +00:00
705d31203c
generic: rtl8366_smi: remove duplicated spinlock initialization
...
SVN-Revision: 31916
2012-05-27 17:09:45 +00:00
9217115687
generic: rtl8366_smi: rename debugfs Kconfig symbol
...
SVN-Revision: 31915
2012-05-27 17:09:43 +00:00
466ef30173
generic: rtl8367: allow to use VLANs > 31
...
SVN-Revision: 31914
2012-05-27 17:09:41 +00:00
f567980d38
move files-3.3 -> files
...
SVN-Revision: 31912
2012-05-27 16:13:02 +00:00
8002770520
3.2 R.I.P.
...
SVN-Revision: 31911
2012-05-27 16:12:59 +00:00
81ddc886e1
dgn3500 support with eeprom loading from sysfs
...
WIFI eeprom:
As discussed, it is impossible for nand and spi flash platforms to have the eeprom data available from mtd. I suggested to load the eeprom from user-space. I've looked into regular firmware loading but this is only possible when using modules. I've created a sysfs entry that allows reading and writing the eeprom data to the platform data. After loading the eeprom data I rely on pci-hotplug support to disable the bogus pci device and rescan the bus (with fixups and all). Because hotplug is not available, an init script is created that performs the copy from mtd to platform data. I think it is best to eventually move the sysfs functions to dev_wifi_athxk.c file, this would get rid of the external to the ath9k platform data.
SPI flash:
It seems that the spi-xway driver is not really working. It causes my kernel to crash in all sorts of ways. I added to bitbang SPI to be able to the calibration data mention above.
I've kept the original mtd partitioning that Netgear uses.
Buttons/LED:
Both buttons are working properly. Two leds are not enabled: The red internet led is connected to the pci_gnt1 pin... I can't disable it because then DMA stops working.
The green wifi led is connected to an unknown atheros gpio.
Signed-off-by: Pieter Voorthuijsen <p.voorthuijsen at gmail.com>
SVN-Revision: 31910
2012-05-27 16:02:22 +00:00
6e8fe84472
fixes zyxel p2601hnfx
...
moves the linux partition, removes the config partition and the
buttons settings have small adjustments.
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 31909
2012-05-27 16:02:20 +00:00
3f2f50c681
Add basic configuration for new board ZTE H201L. Still missing are button and led gpio values.
...
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 31908
2012-05-27 16:02:16 +00:00
51bc47ce7c
kernel: properly pad the allocated headroom in skb_cow to NET_SKB_PAD
...
SVN-Revision: 31906
2012-05-27 15:16:37 +00:00
0b8c1c8dfb
linux/3.2: R.I.P.
...
SVN-Revision: 31905
2012-05-27 15:01:37 +00:00
20ba6d90e3
xburst: remove support for old kernels
...
SVN-Revision: 31904
2012-05-27 15:01:35 +00:00
d043cb2c34
xburst: switch to 3.3 and add broken flag
...
SVN-Revision: 31903
2012-05-27 15:01:33 +00:00
9a26e9f843
xburst: add support for 3.3
...
SVN-Revision: 31902
2012-05-27 15:01:32 +00:00
9dd7a6d9e2
ppc44x: remove 3.2 support
...
SVN-Revision: 31901
2012-05-27 15:01:30 +00:00
05d74942b1
ppx44x: switch to 3.3 and add broken flag
...
SVN-Revision: 31900
2012-05-27 15:01:28 +00:00
9300e0496c
ppc44x: add support for 3.3
...
Compile tested only.
SVN-Revision: 31899
2012-05-27 15:01:27 +00:00
c50f1f7536
cobalt: switch to 3.3 and add broken flag
...
Compile tested only.
SVN-Revision: 31898
2012-05-27 15:01:26 +00:00
471cf87ff0
ep93xx: remove 3.2 support
...
SVN-Revision: 31897
2012-05-27 15:01:24 +00:00
400b9b5b87
ep93xx: switch to 3.3 and add broken flag
...
SVN-Revision: 31896
2012-05-27 15:01:23 +00:00
7501f2364f
ep93xx: add support for 3.3
...
Compile tested only.
SVN-Revision: 31895
2012-05-27 15:01:21 +00:00
907e88a37f
au1000: remove 3.2 support
...
SVN-Revision: 31894
2012-05-27 15:01:18 +00:00
fbe10e73c6
au1000: switch to 3.3 and add broken flag
...
SVN-Revision: 31893
2012-05-27 15:01:17 +00:00
e065d5cfbe
au1000: add support for 3.3
...
Compile tested only.
SVN-Revision: 31892
2012-05-27 15:01:15 +00:00
de4c4d35e1
linux/3.1: R.I.P.
...
SVN-Revision: 31891
2012-05-27 15:01:09 +00:00
cead4b47ab
omap24xx: remove 3.1 support
...
SVN-Revision: 31890
2012-05-27 15:01:07 +00:00
7a4db11fbb
omap24xx: switch to 3.3 and add broken flag
...
SVN-Revision: 31889
2012-05-27 15:01:05 +00:00
d004168445
cns3xxx: remove 3.1 support
...
SVN-Revision: 31888
2012-05-27 15:01:03 +00:00
6f2ca5da39
cns3xxx: switch to 3.3 and add broken flag
...
SVN-Revision: 31887
2012-05-27 15:01:02 +00:00
6f89cffc9a
kernel: add a few patches for avoiding unnecessary skb reallocations - significantly improves ethernet<->wireless performance with mac80211 based drivers
...
SVN-Revision: 31886
2012-05-27 14:43:58 +00:00
ec7786c2ec
bcm63xx: build images for DSL-274XB revision F1
...
Build images for D-Link DSL-274XB revision F1. Flashing
through original web UI as well as CFE works.
Known issues:
* wifi led inverted (on when wifi is off and vice cersa)
* same issues as generic bcm6328 support
SVN-Revision: 31885
2012-05-27 13:22:51 +00:00
8aac009cc9
bcm63xx: add ath9k to atheros wifi profile
...
SVN-Revision: 31884
2012-05-27 13:22:48 +00:00
4aa43122ab
bcm63xx: enable bcm6328 support and required drivers
...
BCM6328 support is in a usable state, with the following issues
* internal switch port not configurable
* external phys not supported
* broadcom wifis will probably not work correctly
* and all other generic bcm63xx issues (so yes, still no ADSL)
SVN-Revision: 31883
2012-05-27 13:22:46 +00:00
e5575fe335
bcm63xx: add support for DSL-274XB rev F1
...
SVN-Revision: 31882
2012-05-27 13:22:43 +00:00
a7a82db16f
bcm63xx: fix port state after network down
...
bcm_enetsw_probe did not properly reset port states, resulting in
connected ports staying disabled after bringing up the interface the
second time.
SVN-Revision: 31881
2012-05-27 13:22:40 +00:00
e19ed52fd1
bcm63xx: add a fixup for ath9k devices
...
SVN-Revision: 31880
2012-05-27 13:22:37 +00:00
e34018cc9e
bcm63xx: add support for the HSSPI controller
...
Add support for the HSSPI controller found on bcm6328 and SPI attached
flash.
SVN-Revision: 31879
2012-05-27 13:22:33 +00:00
099d5eec06
bcm63xx: add preliminary support for bcm6328
...
SVN-Revision: 31878
2012-05-27 13:22:29 +00:00
7dbb132c88
bcm63xx: add flash type detection
...
SVN-Revision: 31877
2012-05-27 13:22:25 +00:00
b0ffeb0021
bcm63xx: pad Speedport W303 V images to 4 MiB
...
Prevents CFE from flashing to the second image offset. Fix up the rootfs
length on first boot else CFE will complain.
SVN-Revision: 31876
2012-05-27 13:22:22 +00:00
226b030e44
bcm63xx: add a default switch configuration for DSL-274XB
...
SVN-Revision: 31874
2012-05-27 13:22:17 +00:00
db1ff5c6fa
bcm63xx: setup network config through uci-defaults
...
SVN-Revision: 31873
2012-05-27 13:22:14 +00:00
72b4fdecc9
bcm63xx: move the board name workaround to /lib/brcm63xx.sh
...
SVN-Revision: 31872
2012-05-27 13:22:11 +00:00
dd37687de0
bcm63xx: use the exact board id as board identification string
...
No need to keep the bcm63xx/ at the start or the chipid info at the end.
SVN-Revision: 31871
2012-05-27 13:22:08 +00:00
230c0eb2cb
kernel: fix a warning in the connmark module
...
SVN-Revision: 31856
2012-05-24 18:25:08 +00:00
2ae5581447
kernel: update linux 3.3 to 3.3.7
...
SVN-Revision: 31848
2012-05-23 21:05:32 +00:00
c57409e79d
ar71xx: fix an insignificant typo
...
Patch from #11485 .
SVN-Revision: 31847
2012-05-23 21:05:30 +00:00
013f434f5b
ar71xx: fix WLAN led for RB751U-2HnD and RB751G-2HnD
...
Patch by Kamil Trzciński <ayufan@osk-net.pl>
SVN-Revision: 31846
2012-05-23 21:05:25 +00:00
758f670376
ar71xx: add support for TP-Link TL-MR3040
...
Support for TP-Link TL-MR3040. Power LED not working - always on red, after
start should be green.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 31845
2012-05-23 21:05:24 +00:00
e4720dfa95
ramips: Add byte queue limits support to net/ethernet/ramips_main.c
...
Add byte queue limits support to net/ethernet/ramips_main.c
"Byte queue limits are a mechanism to limit the size of the transmit
hardware queue on a NIC by number of bytes. The goal of these byte
limits is too reduce latency (HOL blocking) caused by excessive
queuing in hardware (aka buffer bloat) without sacrificing
throughput."
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 31844
2012-05-23 21:05:23 +00:00
1d286fd755
ramips: Enable sysupgrade for Sitecom WL-351
...
Sysupgrade works just fine on my Sitecom WL-351 after adding this
oneliner.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 31843
2012-05-23 21:05:22 +00:00
Felix Fietkau
Florian Fainelli
John Crispin
Luka Perkov
Jonas Gorski
Gabor Juhos