Commit Graph

255 Commits (f080f2aa8ed71967d442afec7be1f24735f693b9)

Author SHA1 Message Date
Gabor Juhos a447f1810c ar71xx: enable MIB counters in the built-in switch of the AR934x
SVN-Revision: 31476
2012-04-25 13:02:11 +00:00
Gabor Juhos c00b53f3d0 ar71xx: move micrel PHY driver to the generic linux target
SVN-Revision: 30946
2012-03-15 09:25:53 +00:00
Gabor Juhos ff909edf94 ar71xx: ag71xx: fix ARP frame reception on AR934x switch ports
SVN-Revision: 30926
2012-03-13 17:29:38 +00:00
Gabor Juhos cd6a4cde13 ar71xx: ag71xx: start aneg on switch PHYs after reset
SVN-Revision: 30925
2012-03-13 17:29:37 +00:00
Gabor Juhos 7c9534cfd7 ar71xx: ag71xx: poll PHY status of all available switch ports
SVN-Revision: 30924
2012-03-13 17:29:36 +00:00
Gabor Juhos 8449eecf5f ar71xx: ag71xx: allow to use port 5 of the AR934x built-in switch
SVN-Revision: 30923
2012-03-13 17:29:34 +00:00
Gabor Juhos c455a0f7be ar71xx: ag71xx: fix get_port_link callback
SVN-Revision: 30841
2012-03-07 16:32:35 +00:00
Gabor Juhos 5a83b3a5c7 ar71xx: ag71xx: use the generic get_port_link implementation
SVN-Revision: 30840
2012-03-07 16:32:34 +00:00
Gabor Juhos 7052847972 ar71xx: ag71xx: keep VLAN tags if VLAN is not enabled
SVN-Revision: 30768
2012-03-01 19:49:05 +00:00
Gabor Juhos 766999085a ar71xx: ag71xx: add BQL support
It will be usable only from linux-3.3.

Based on a patch by Dave Taht <dave.taht@bufferbloat.net>

SVN-Revision: 30417
2012-02-10 14:56:47 +00:00
Gabor Juhos 32a18a05f8 ar71xx: add preliminary support for 3.3
SVN-Revision: 30410
2012-02-10 11:53:56 +00:00
Gabor Juhos d72bde99cd ar71xx: merge files-3.2 to files
SVN-Revision: 30405
2012-02-10 08:19:31 +00:00
Gabor Juhos 386cbfe45b ar71xx: move arch specific files to files-2.6.39
SVN-Revision: 29867
2012-01-22 22:38:11 +00:00
Gabor Juhos f90e578903 ar71xx: include linux/module.h in the micrel phy driver
SVN-Revision: 29848
2012-01-22 13:51:49 +00:00
Gabor Juhos 8c2482f76e ar71xx: ag71xx: implement get_port_{link,stats} callbacks
SVN-Revision: 29626
2011-12-31 15:02:26 +00:00
Felix Fietkau db0a1db257 ar71xx: set a reserved bit that resets to 1 when writing the address table control register on the ar7240 switch (should fix #10547)
SVN-Revision: 29598
2011-12-22 05:43:53 +00:00
Gabor Juhos 36bc2c2c80 ar71xx: ag71xx: fix switch port setup for AR934X
SVN-Revision: 29554
2011-12-15 22:25:32 +00:00
Gabor Juhos 00667c3846 ar71xx: ag71xx: allow to connect PHY4 to the CPU on AR934X
SVN-Revision: 29553
2011-12-15 22:25:30 +00:00
Gabor Juhos 0540970345 ar71xx: ag71xx: setup switch interface mode on AR934X
SVN-Revision: 29552
2011-12-15 22:25:29 +00:00
Gabor Juhos 44014110b8 ar71xx: ag71xx: detect the built-in switch of the AR934X SoCs
SVN-Revision: 29551
2011-12-15 22:25:28 +00:00
Gabor Juhos 9ae65588d8 ar71xx: introduce ar71xx_switch_data
SVN-Revision: 29549
2011-12-15 22:25:11 +00:00
Gabor Juhos b7d7481b07 ar71xx: ag71xx: check PHY IDs before accessing the switch registers
SVN-Revision: 29541
2011-12-15 13:25:23 +00:00
Gabor Juhos 0655552860 ar71xx: ag71xx: don't use port 4 of the switch, it is not connected on ar724x
SVN-Revision: 29540
2011-12-15 13:25:21 +00:00
Gabor Juhos 204fc6bed5 ar71xx: ag71xx: nuke ar7240sw_init
SVN-Revision: 29539
2011-12-15 13:25:20 +00:00
Gabor Juhos d2316b2a45 ar71xx: ag71xx: add support for getting switch port link status
SVN-Revision: 29017
2011-11-13 11:27:04 +00:00
Gabor Juhos 34015ed6e8 ar71xx: ag71xx: remove unused mii_ctrl field from struct ag71xx
SVN-Revision: 29015
2011-11-13 11:27:01 +00:00
Gabor Juhos 2d882cff23 ar71xx: ag71xx: remove unused mii_cfg related functions and defines
SVN-Revision: 29014
2011-11-13 11:27:00 +00:00
Gabor Juhos 538a9493b9 ar71xx: set MII interface speed from the set_speed callbacks
SVN-Revision: 29013
2011-11-13 11:26:59 +00:00
Gabor Juhos 93cd46be13 ar71xx: rename set_pll callback to set_speed in ag71xx_platform_data
Also rename the corresponding callback functions.

SVN-Revision: 29012
2011-11-13 11:26:57 +00:00
Gabor Juhos 9579bb4267 ar71xx: ag71xx: remove MII interface setup code
SVN-Revision: 29011
2011-11-13 11:26:56 +00:00
Gabor Juhos 2f9e535e89 ar71xx: ag71xx: use fixed link parameters if the mii bus is not registered
SVN-Revision: 28977
2011-11-12 10:54:16 +00:00
Felix Fietkau 7a2efd8c28 ar71xx: remove dead code
SVN-Revision: 28851
2011-11-08 00:33:20 +00:00
Felix Fietkau 94309039b7 ar71xx: on ar7240, exclude ports from their own port vlan destination mask
SVN-Revision: 28850
2011-11-08 00:33:15 +00:00
Jonas Gorski c674c874b7 ag71xx: close a race between the phy state machine and link state
A fast stop/start cycle could leave the ag71xx interrupts and tx engine
disabled when using a phy driver with a fixed link and the start/stop
happens between two phy state machine polls.

Prevent this by always forcing the link down on stop regardless of phy
state and having a phy connected.

SVN-Revision: 28380
2011-10-08 11:37:14 +00:00
Felix Fietkau 1bdf65f580 ar71xx: fix register range check for DMA stuck checks (thx, Frédéric Moulins)
SVN-Revision: 28213
2011-09-11 17:44:12 +00:00
Felix Fietkau 12c84f8eeb ar71xx: add some code to detect DMA stuck conditions on ar7240
SVN-Revision: 27975
2011-08-13 22:30:14 +00:00
Felix Fietkau 85ccc74e1b ar71xx: on ar724x only reset the link status in the restart handler, the fast reset takes care of DMA stuck issues
SVN-Revision: 27973
2011-08-13 21:49:46 +00:00
Felix Fietkau 4b75394056 ar71xx: fix ethernet FIFO state corruption on ar7240
When starting/stopping DMA sometimes the FIFO state gets corrupted,
leading to wildly fluctuating latencies or packet data corruption.
Fix this by issuing a fast MAC reset as soon as the link is detected
as up. Fixes #9689, #9405

SVN-Revision: 27896
2011-08-04 17:36:31 +00:00
Felix Fietkau d2aeca6b6d ag71xx: fix memory corruption issues on ar7240 on ethernet start/stop
When the DMA engine state gets corrupted due to a hardware issues, it
often won't stop rx until a full reset is issued. In that case the hardware
must keep a valid descriptor, otherwise it will write to random places in
system RAM, triggering random crashes. To fix this, keep a dummy descriptor
without a buffer that keeps the DMA engine in a sane state until the reset
is done

SVN-Revision: 27895
2011-08-04 17:36:27 +00:00
Felix Fietkau 500c3a1475 ar71xx: fix MAC/MDIO reset mask handling
SVN-Revision: 27894
2011-08-04 17:36:23 +00:00
Felix Fietkau c7173a211d ar71xx: reinitialize global switch settings after reset on ar7240
SVN-Revision: 27705
2011-07-20 14:39:47 +00:00
Felix Fietkau ca473833c4 ar71xx: configure address aging on ar7240
SVN-Revision: 27704
2011-07-20 14:39:42 +00:00
Felix Fietkau fefc79f3cb ar71xx: reset the phy in the ethernet init on ar724x
SVN-Revision: 27703
2011-07-20 12:04:34 +00:00
Felix Fietkau 005fe5d1fd ar71xx: make sure that rx and interrupts are disabled before issuing the hardware reset
SVN-Revision: 27702
2011-07-20 12:04:29 +00:00
Felix Fietkau e7ab000008 ar71xx: increase the delay after the ethernet MAC reset
SVN-Revision: 27701
2011-07-20 12:04:25 +00:00
Felix Fietkau 255dcaa3a6 ar71xx: fix an unused variable warning
SVN-Revision: 27700
2011-07-20 12:04:20 +00:00
Felix Fietkau f3d693c0ee ar71xx: do not reset the hardware on transmit timeout - this would mess up the up the PHY state
SVN-Revision: 27568
2011-07-09 06:30:13 +00:00
Felix Fietkau 2806c75c07 ag71xx: keep the rx engine stopped while the link is not up, should hopefully fix stability issues from #9405
SVN-Revision: 27567
2011-07-09 06:29:46 +00:00
Felix Fietkau 31dd60689e Revert "ar71xx: only enable the rx engine after the link is up..."
It messes up the DMA state when the link goes down

SVN-Revision: 27088
2011-06-01 18:15:43 +00:00
Gabor Juhos 60d5abbc27 ar71xx: ag71xx: make ring sizes configurable via ethtool
SVN-Revision: 27041
2011-05-31 22:53:10 +00:00
Gabor Juhos 7a2651f633 ar71xx: ag71xx: prepare to make ring sizes configurable
SVN-Revision: 27040
2011-05-31 22:53:09 +00:00
Gabor Juhos 669aba3871 ar71xx: ag71xx: nuke unused AG71XX_TX_FIFO_LEN define
Reported-by: Dave Täht <dave.taht@gmail.com>

SVN-Revision: 27039
2011-05-31 22:53:07 +00:00
Felix Fietkau 2b5402d128 ar71xx: only enable the rx engine after the link is up, fixes a race condition that got rx stuck when the interface is brought up during lots of inbound traffic (thx, matteo)
SVN-Revision: 27035
2011-05-30 23:08:01 +00:00
Felix Fietkau 0ebc93831f ar71xx: disable flow control for ar724x, it can get stuck in a loop of continously sending MAC pause frames
SVN-Revision: 27034
2011-05-30 23:07:57 +00:00
Matteo Croce 4deecea26b ar71xx: detect link on LAN ports
SVN-Revision: 26922
2011-05-17 11:12:56 +00:00
Matteo Croce c0c2e18452 use correct macros and frame size in ag71xx
SVN-Revision: 26890
2011-05-14 23:10:06 +00:00
Gabor Juhos 5d77f370d6 ar71xx: ag71xx: make switch register access atomic
Reading of the PHY registers occasionally returns with bogus values
under heavy load. This misleads the PHY driver and thus causes false
link/speed change notifications which leads to performance loss.

This is easily noticable during an iperf session:

...
[  3] 52.0-53.0 sec  11.3 MBytes  94.4 Mbits/sec
[  3] 53.0-54.0 sec  11.4 MBytes  95.4 Mbits/sec
eth1: link down
br-lan: port 2(eth1) entering forwarding state
eth1: link up (100Mbps/Full duplex)
br-lan: port 2(eth1) entering forwarding state
br-lan: port 2(eth1) entering forwarding state
[  3] 54.0-55.0 sec  6.75 MBytes  56.6 Mbits/sec
[  3] 55.0-56.0 sec  0.00 Bytes  0.00 bits/sec
[  3] 56.0-57.0 sec  10.5 MBytes  88.1 Mbits/sec
...
[  3] 169.0-170.0 sec  11.4 MBytes  95.4 Mbits/sec
[  3] 170.0-171.0 sec  11.4 MBytes  95.4 Mbits/sec
eth1: link up (10Mbps/Half duplex)
[  3] 171.0-172.0 sec  7.63 MBytes  64.0 Mbits/sec
[  3] 172.0-173.0 sec  9.38 MBytes  78.6 Mbits/sec
eth1: link up (100Mbps/Full duplex)
[  3] 173.0-174.0 sec  11.3 MBytes  94.4 Mbits/sec
[  3] 174.0-175.0 sec  11.4 MBytes  95.4 Mbits/sec

SVN-Revision: 26856
2011-05-08 16:32:53 +00:00
Gabor Juhos 3711658281 ar71xx: ag71xx: fix section mismatch warnings
The function __devinit ag71xx_probe() references
a function __devexit ag71xx_phy_disconnect().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
ag71xx_phy_disconnect() so it may be used outside an exit section.

The function ag71xx_phy_disconnect() references a function in an exit
section.
Often the function ag71xx_ar7240_cleanup() has valid usage outside the
exit section
and the fix is to remove the __devexit annotation of
ag71xx_ar7240_cleanup.

SVN-Revision: 26855
2011-05-08 13:30:36 +00:00
Gabor Juhos ef53029870 ar71xx: ag71xx: fix build error if debugfs is enabled
SVN-Revision: 26854
2011-05-08 13:30:26 +00:00
Gabor Juhos 8b67d748cb ar71xx: ag71xx: add debugfs entry for [rt]x_ring
SVN-Revision: 26845
2011-05-07 12:40:34 +00:00
Gabor Juhos 2166432ba0 ar71xx: ag71xx: add timestamps to ag71xx_buf
SVN-Revision: 26844
2011-05-07 12:40:28 +00:00
Gabor Juhos 896e1d1ab4 ar71xx: ag71xx: use dynamically allocated buffer for napi_stats
SVN-Revision: 26843
2011-05-07 12:40:26 +00:00
Gabor Juhos a6708d20d1 ar71xx: ag71xx: use debugfs_remove_recursive
SVN-Revision: 26842
2011-05-07 12:40:25 +00:00
Felix Fietkau 41ee4a283c ar71xx: only allow internal access to the ar7240 switch, export the MDIO bus behind the switch instead
SVN-Revision: 26393
2011-04-02 00:47:29 +00:00
Felix Fietkau acbb3e50e7 ar71xx: frequent ethernet mac resets upset the MDIO bus on ar7240, so do not run them on every device open, only on tx timeouts
SVN-Revision: 26392
2011-04-02 00:47:25 +00:00
Gabor Juhos 3106aea40b ar71xx: drivers/ag71xx: remove deprecated usage of IRQF_SAMPLE_RANDOM
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>

SVN-Revision: 23982
2010-11-12 18:52:28 +00:00
Gabor Juhos 30ef7d55fc ar71xx: use pr_* functions in drivers
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>

SVN-Revision: 23981
2010-11-12 18:52:12 +00:00
Gabor Juhos f4d5c885e4 ar71xx: return statements does not need parenthesis
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>

SVN-Revision: 23979
2010-11-12 18:51:38 +00:00
Gabor Juhos e244e1c7cd ar71xx: fix inline attribute location
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>

SVN-Revision: 23978
2010-11-12 18:51:21 +00:00
Gabor Juhos acd8ad4de5 ar71xx: wrap long lines
(build errors has been fixed - juhosg)

Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>

SVN-Revision: 23977
2010-11-12 18:51:04 +00:00
Gabor Juhos 500fac1735 ar71xx: fix whitespaces nits
(build error has been fixed - juhosg)

Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>

SVN-Revision: 23975
2010-11-12 18:50:29 +00:00
Felix Fietkau 6656450c6d ar71xx: fix more section mismatches
SVN-Revision: 23575
2010-10-21 18:42:16 +00:00
Felix Fietkau 8858d90afe ar71xx: improve 2.6.36 compatibility. also, instead of adding a forward port patch to the 2.6.36 patches, add a backport patch to 2.6.32
SVN-Revision: 23574
2010-10-21 18:42:11 +00:00
Felix Fietkau 523fcf0497 ar71xx: add a new driver for the ar7240 switch using swconfig. hooks directly into the ethernet driver, as MAC resets also require switch reinitializations and the switch is part of the cpu core anyway switch only tl-wr741nd (and other devices using this board file, such as tl-wr841nd) over to using this by default, as other devices are still untested fixes #7563
SVN-Revision: 22675
2010-08-16 19:21:57 +00:00
Felix Fietkau a27ea45e76 ar71xx: only reinit the ethernet MAC at .open() on ar724x for now, until we've figured out what part of it causes the issue described in #7563
SVN-Revision: 22075
2010-07-06 12:40:07 +00:00
Felix Fietkau 15b209d09f ag71xx: reset the hardware during open(), this improves recovery from tx timeouts on ar724x considerably
SVN-Revision: 22055
2010-07-04 02:15:08 +00:00
Felix Fietkau 89da22d1ea ag71xx: fix a memory corruption bug that happens if you flood the interface with packets while it's being brought down fixes boot time crashes under load reported by matteo
SVN-Revision: 22054
2010-07-04 01:31:33 +00:00
Felix Fietkau 7966004d99 ag71xx: remove rx alignment code for small packets, it seems to break ipv6 for some reason (fixes #7236)
SVN-Revision: 21166
2010-04-26 16:39:13 +00:00
Felix Fietkau 1c0e751391 ar71xx: fix up alignment handling
- on ar724x, rx buffers can be aligned with an offset of 2, which keeps the ip header aligned
- alignment offset is only added if the ar8216 workaround is not active and the phy driver does not advertise its own packet alignment
- ar71xx and ar91xx can not handle rx alignment offsets, however taking a hit on unaligned exceptions seems to have less overhead than re-aligning the data for large packets
- use memmove to re-align small packets, if necessary

tested on ar9132, ar7240 and ar7242 based devices without ar8216 headers

SVN-Revision: 20892
2010-04-15 23:31:17 +00:00
Gabor Juhos 4c29a2c263 ar71xx: ag71xx: avoid unalinged accesses when using the phy specific receive functions
Cc: backfire@openwrt.org

SVN-Revision: 20751
2010-04-09 08:40:06 +00:00
Gabor Juhos 4a28844d80 ar71xx: ag71xx: call the phy driver's netif_receive_skb()
Ag71xx needs to call the phy's netif_receive_skb() to allow phy drivers
to mangle rx packets. This patch fixes it.

This fixes the header mangling of the AR8216 driver.

Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
Cc:backfire@openwrt.org

SVN-Revision: 20750
2010-04-09 08:38:46 +00:00
Gabor Juhos c874513cfa ar71xx: fix broken LAN ports on the boards with AR8216 switch (closes #7024)
* cc: backfire@openwrt.org

SVN-Revision: 20673
2010-04-03 13:59:08 +00:00
Gabor Juhos b7ca043240 ar71xx: ag71xx: copy received packet to avoid unaligned access in the IP stack
SVN-Revision: 20506
2010-03-27 13:05:27 +00:00
Gabor Juhos f9acf8ada1 ar71xx: ag71xx: introduce ag71xx_has_ar8216() helper
SVN-Revision: 20505
2010-03-27 13:05:24 +00:00
Gabor Juhos 200db5ebb5 ar71xx: ag71xx: reorganize ag71xx_rx_packet function
SVN-Revision: 20504
2010-03-27 13:05:20 +00:00
Gabor Juhos 245775a49f ar71xx: ag71xx: Add netpoll support
This patch adds support for polling interrupts, used by
netconsole and the likes.

Tested on d-link dir-615 C1 using netconsole.

Signed-off-by: Pat Erley <pat-lkml@erley.org>

SVN-Revision: 20503
2010-03-27 13:05:17 +00:00
Andy Boyett 681054333e wrt400n: lan ports don't need the ar8216 workaround
SVN-Revision: 20491
2010-03-26 19:09:11 +00:00
Gabor Juhos 9a1031ce6d ar71xx: change PHY select logic, and update phy_masks
SVN-Revision: 20358
2010-03-21 18:16:07 +00:00
Gabor Juhos 2a818f388a ar71xx: ag71xx: fix MAC address setup
SVN-Revision: 20092
2010-03-09 18:05:36 +00:00
Gabor Juhos 2702ae4e8f ar71xx: ag71xx: move calling ag71xx_phy_stop out from spinlock
SVN-Revision: 20004
2010-03-05 20:29:22 +00:00
Gabor Juhos a4bccded57 ar71xx: ag71xx: move link update function
SVN-Revision: 20003
2010-03-05 20:29:18 +00:00
Gabor Juhos eacf9a7614 ar71xx: ag71xx: don't use dev->trans_start
SVN-Revision: 20002
2010-03-05 20:29:14 +00:00
Gabor Juhos ba288eeb84 ar71xx: ag71xx: use dma_unmap_single to unmap frames
SVN-Revision: 20001
2010-03-05 20:29:10 +00:00
Gabor Juhos 0e4eaea770 ar71xx: ag71xx: use correct device pointer for dma_map_single
SVN-Revision: 19951
2010-03-02 13:36:18 +00:00
Gabor Juhos 84823e1477 ar71xx: ag71xx: don't use virt_to_phys
SVN-Revision: 19950
2010-03-02 13:36:15 +00:00
Gabor Juhos 4a987d6008 ar71xx: ag71xx: simplify register access functions
SVN-Revision: 19949
2010-03-02 13:36:12 +00:00
Gabor Juhos e157281c5d ar71xx: ag71xx: use NETDEV_TX_OK
SVN-Revision: 19948
2010-03-02 13:36:09 +00:00
Gabor Juhos 1612fd447d ar71xx: enable TX/RX flow control on the AR7240
SVN-Revision: 19832
2010-02-24 13:38:41 +00:00
Gabor Juhos 49c4df5487 rtl8366: make it available on all platforms
SVN-Revision: 19329
2010-01-25 15:13:38 +00:00
Gabor Juhos 97b983c8b9 rtl8366s: simplify mib counters handling
SVN-Revision: 19326
2010-01-25 14:24:53 +00:00