Adds specification of the correct cpu_port for Linksys E3000V1 and WRT610NV2
in /lib/preinit/05_init_interfaces_brcm. The list of devices will need to
be expanded. Is there a way to determine the correct cpu_port to use in a
generic sense; for instance, if "/proc/switch/eth0/port/8" exists, or if
"/sys/class/net/eth0/device/driver/module/drivers/bcma:bgmac" exists? Could
a similar method be used in "/etc/init.d/netconfig"?
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 35491
The default profile now contains Ethernet drivers for all the types
found on supported boards. There are other profiles for each Ethernet
driver.
SVN-Revision: 35314
Update the default IRQ assignment for unrecognized devices per
the upstream change.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 35121
1) Fix what appears to be a logic error in bgmac_phy_advertise.
2) Fix bgmac_ioctl to use passed phy_id; needed for switch-robo
interface w/ the driver to work correctly. I still have the issue
with the interface always being HD when the speed/duplex is set
manually (e.g., echo "100FD" > /proc/switch/eth0/port/N/media).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 35052
This Ethernet driver is in early development stage and still has some problems.
This was working on my bcm4716 based device.
Thanks to Rafał Miłecki <zajec5@gmail.com> for writing this driver.
SVN-Revision: 34995
Adjust the IRQ Flag value from 8 to 7 for I2S Core for BCM4716 and
BCM4748 (per the Broadcom SDK). IRQ Flag values greater than 7 are
ignored when setting the interrupt masks.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 34990
The behaviour of calling 'mount' differed depending on whether it called
the busybox-mount, the mount of util-linux, the mount defined in
/lib/functions.sh and /lib/functions/boot.sh
/etc/preinit even included /lib/functions.sh and /lib/functions/boot.sh,
both re-defining 'mount'.
SVN-Revision: 34792
I noticed these changes when reviewing the 2011 Broadcom SDK. I haven't
noticed any obvious changes in behavior with them applied; but thought I
should at least pass them on.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 34670
The irq signal numbers that are send by the cpu are increased by 2 from
the number programmed into the mips core by bcma.
Return the irq number on which the irqs are send in bcma_core_irq() now.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 34669
These patches are not specific to bcm47xx and will be used on other
platforms as well.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 34501
The ASUS WL-520gU and some other similar Asus devices have a BCM5354
running at 200MHZ and not at 240 which is the default for this SoC.
This fixes#4083.
SVN-Revision: 34325
In the old configuration the SoC issued a reboot if the watchdog was
killed also if it was kill with TERM and not KILL.
This will fix#11724.
SVN-Revision: 34324
For sysupgrade the generic image should be used and the special image for the wgt634u is just needed for initial flashing over CFE.
russell reported that with this patch sysupgrdae did not worked for him any more and he could not reproduce the error described in #11420.
With the patch the linux partition also contained the loader which is in the first 128KB.
SVN-Revision: 34201
Hauke Mehrtens
Mirko Vogt
Gabor Juhos
Florian Fainelli