Similarly to the previously broken address pools, DNS-servers and some
MSRs could be advertised incorrectly as well. This is now fixed.
SVN-Revision: 39739
This patch introduces 802.11ac support to mac80211 and hostapd. The split of
VHT160 in two 80 MHz bands is not yet supported, since it requires an
additional user supplied parameter for the channel of the second band.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
[sven@open-mesh.com: Rebased patch, merged htmode and vhtmode,
removed special hwmode, replaced uci vht_capab list with overwritable
autoconfig, fixed hostapd integration, fixed commit description, add HT40+/-
for VHT modes, add VHT40 center_freq autoconfig, refactored major parts]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 39456
Introduced by ("netifd: add wireless configuration support and port mac80211 to
the new framework")
Reported-by: René van Weert <r.vanweert@sowifi.com>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
SVN-Revision: 39288
Introduced by ("netifd: add wireless configuration support and port mac80211 to
the new framework")
Reported-by: René van Weert <rene@sowifi.com>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
SVN-Revision: 39231
- cache udhcp check results to speed up subsequent reloads
- enable procd file tracking for /var/etc/dnsmasq.conf to only reload service if needed
- implement reload action to only restart dnsmasq if /var/etc/dnsmasq.conf actually changed
- launch dnsmasq from interface hotplug to avoid race conditions with network bringup
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39152
This commit changes the dnsmasq init script to use the interface
status exposed by netifd. The old references to scan_interfaces()
and (indirect) accesses to uci state variables are removed and
replaced with corresponding network_*() calls.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39101
Before this patch, if we specify a plugin specific option through
`pppd_options` in /etc/config/network, e.g. `rp_pppoe_verbose 1`, pppd
would quit with the following error in log.
Wed Oct 9 09:42:58 2013 daemon.notice netifd: GORG (1689): /usr/sbin/pppd: unrecognized option 'rp_pppoe_verbose'
Wed Oct 9 09:42:58 2013 daemon.err pppd[1689]: unrecognized option 'rp_pppoe_verbose'
Wed Oct 9 09:42:58 2013 daemon.notice netifd: GORG (1689): pppd version 2.4.5
Wed Oct 9 09:42:58 2013 daemon.notice netifd: GORG (1689): Usage: /usr/sbin/pppd [ options ], where options are:
This is due to the requirement that function add_option() should be
called by the plugin_init() function first before pppd can parse those
options.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 38911
Changeset r36943 ("dnsmasq: use host-record instead of address") removed
the automatic domain expansion for config domain sections, this breaks
existing setups and alters the old behaviour in unexpected ways, therfore
restore behaviour of the current stable release.
Additionally handle fully qualified hostnames properly when setting up the
own hostrecord by stripping the local domain part form the given name
instead of unconditionally appending it, so that "example.lan" results
in "example example.lan" and not "example.lan example.lan.lan".
SVN-Revision: 38648
- clean up duplication of procd instance handling code
- using --cd *after* --config is rather pointless
- to be able to log errors properly, --syslog needs to be passed before --config
- tell procd about the generated or referenced config file instead of
the uci file. this avoids having to restart all instances if only one
of them changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 38632
Possible parameters are yes, no and adaptive. See manpage for more information.
Signed-off-by: Philipp Borgers <borgers@mi.fu-berlin.de>
SVN-Revision: 38412
There are certain consumer devices which are outliers in protocol conformance.
An example is Samsung bluray players, which require broadcast DHCP responses
(on Ethernet only, strangely not on Wifi).
By specifying:
config host
...
option broadcast 1
this will enable the response to be sent as an Ethernet broadcast and not as
a unicast.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 38365
proto_pptp_setup is responsible for loading the required modules to establish
a pptp connection to a foreign peer. The function checks whether all required
modules are already loaded, before actually loading them.
It seems that the filter being used to accomplish this, is not restrictive
enough in some cases. For instance when pptp nat helper modules are present on
a system, and already loaded before a pptp connection is enabled. Then the
search filter (possibly) returns the following for module=pptp, where actually
no matches are expected, resulting in the pptp.ko module not being loaded,
thereby failing to establish the pptp connection.
# module="pptp" ; grep "$module" /proc/modules
nf_nat_pptp 1312 0 - Live 0x86ce7000
nf_conntrack_pptp 3072 1 nf_nat_pptp, Live 0x86cb9000
nf_nat_proto_gre 784 1 nf_nat_pptp, Live 0x86cba000
nf_conntrack_proto_gre 2368 1 nf_conntrack_pptp, Live 0x86cbf000
nf_nat 9792 13 nf_nat_rtsp,nf_nat_tftp,nf_nat_sip,nf_nat_pptp,nf_nat_h323,nf_nat_proto_gre,nf_nat_amanda,nf_nat_irc,nf_nat_ftp,ipt_REDIRECT,ipt_NETMAP,ipt_MASQUERADE,iptable_nat, Live 0x86ca8000
nf_conntrack 37264 31 nf_nat_rtsp,nf_conntrack_rtsp,nf_nat_tftp,nf_conntrack_tftp,nf_nat_snmp_basic,nf_conntrack_snmp,nf_nat_sip,nf_conntrack_sip,nf_nat_pptp,nf_conntrack_pptp,nf_nat_h323,nf_conntrack_h323,nf_conntrack_proto_gre,nf_nat_amanda,nf_conntrack_amanda,nf_conntrack_broadcast,nf_nat_irc,nf_conntrack_irc,nf_nat_ftp,nf_conntrack_ftp,ipt_MASQUERADE,iptable_nat,nf_nat,xt_helper,xt_connmark,xt_connbytes,xt_conntrack,xt_CT,xt_NOTRACK,xt_state,nf_conntrack_ipv4, Live 0x86c90000
The search filter can be made more accurate/restrictive, by requiring the
occurance of the exact name of the module at the beginning of a line in
/proc/modules.
# module="pptp" ; grep "^$module " /proc/modules
pptp 13296 2 - Live 0x86e80000
Signed-off-by: Tijs Van Buggenhout <tvb@able.be>
SVN-Revision: 38358
Currently, in order to configure the authentication daemon in
8021x mode, we need to set wireless.@wifi-iface[0].encryption="wpa"
Though it works it confuses folks as 8021x is using WEP
encryption and not WPA. Therefore the terminology itself is
confusing. This change adds 8021x as a recognized string for 8021x
authentication.
Signed-off-by: Mathieu Olivari <mathieu@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
SVN-Revision: 38339
Setting wireless.@wifi-iface[N].ext_registrar=1 will enable UPNP
advertising and add an external registrar to the interface this vif
belongs to (br-lan if the vif is included in the LAN bridge). By
enabling this we append upnp_iface=xxx to the hostapd config file.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Mathieu Olivari <mathieu@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
SVN-Revision: 38338
Enable CONFIG_WPS2 for hostapd. This is required to support
options like Virtual Push Button in WPS.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
SVN-Revision: 38337
In 2009 OpenWrt's hostapd config added an "auth_cache" boolean
to be used to address a reported issue #12129 [0] on a forum [1].
The reported issue on the ticket is different that the one
described on the forum. The commit was r33359. This change broke
proper RSN preauthentication [2] [3] [4] expectations on hostapd's
configuration for WPA2 and this in turn disabled PMKSA caching and
Opportunistic Key Caching. This change:
* Leaves the "auth_cache" to be used only for WPA networks for those
looking to use this as a workaround to a reported issue but annotates
a warning over its usage.
* Separate "auth_cache" from WPA2 RSN preauthentication, leaving
WPA2 RSN preauthentication to enabled only with "rsn_preauth" with
the expected and recommended settings.
* Adds a new WPA2 RSN preauthentication "rsn_preauth_testing" to
be used when evaluating funcionality for WPA2 RSN preauthentication
with the expected and recommended settings with the only difference
so far with what should be enabled by default to disable Opportunistic
Key Caching.
Disabling the PMKSA cache should mean the STA could not roam off and back
onto the AP that had PMKSA caching disabled and would require a full
authentication cycle. This fixes this for WPA2 networks with
RSN preauthentication enabled.
This change should be applied to AA as well as trunk.
TL DR;
The issue described on the forum has to do with failure of a STA
being able to try to authenticate again with the AP if it failed
its first try. This may have been an issue with hostapd in 2009
but as per some tests I cannot reproduce this today on a WPA2
network.
The issue described on the ticket alludes to a security issue with the
design of using a Radius server to authenticate to an AP. The issue
vaguely alludes to the circumstances of zapping a user, deleting their
authentication credentials to log in to the network, and that if
RSN preauthentication is enabled with PMKSA caching that the user
that was zapped would still be able to authenticate.
Lets treat these as separate issues.
I cannot reproduce the first issue reported on the forums of not
being able to authenticate anymore on a WPA2 network.
The issue reported on the ticket modified WPA2 RSN preauthentication
by adding two fields to the hostapd configuration if auth_cache
was enabled:
* disable_pmksa_caching=1
* okc=0
The first one disables PMKSA authentication cache.
The second one disables Opportunistic Key Caching.
The issue reported on the ticket was fixed by implementing a workaround
in hostapd's configuration. Disabling PMKSA caching breaks proper use
of WPA2 RSN pre authentication. The usage of disable_pmksa_caching=1
prevents hostapd from adding PMKSA entries into its cache when a successful
802.1x authentication occurs. In practice RSN preauthentication would
trigger a STA to perform authentication with other APs on the same SSID,
it would then have its own supplicant PMKSA cache held. If a STA roams
between one AP to another no new authenitcation would need to be performed
as the new AP would already have authenticated the STA. The purpose of the
PMKSA cache on the AP side would be for the AP to use the same PMKID for
a STA when the STA roams off onto another BSSID and later comes back to it.
Disabling Opportunistic Key Caching could help the reported issue
as well but its not the correct place to address this. Opportunistic
Key Caching enables an AP with different interfaces to share the
PMKSA cache. Its a technical enhancement and disabling it would
be useful to let a testing suite properly test for RSN preauthentication
given that otherwise Opportunistic Key Caching would enable an
interface being tested to derive its own derive the PMKSA entry.
In production though okc=1 should be enabled to help with RSN
preauthentication.
The real fix for this particular issue outside of the scope of hostapd's
configuration and it should not be dealt with as a workaround to
its configuration and breaking expected RSN preauthentication and
technical optimizations. Revert this change and enable users to pick
and choose to enable or disable disable_pmksa_caching and okc expecting them
to instead have read clearly more what these do.
As for the core issure ported, the correct place to fix this is to
enable a sort of messaging between the RADIUS server and its peers
so that if caching for authentication is enabled that cache can be
cleared upon user credential updates. Updating a user password
(not just zapping a user) is another possible issue that would need
to be resolved here. Another part of the solution might be to reduce
the cache timing to account for any systematic limitations (RADIUS
server not able to ask peers to clear cache might be
one).
[0] https://dev.openwrt.org/changeset/33359
[1] https://forum.openwrt.org/viewtopic.php?id=19596
[2] http://wireless.kernel.org/en/users/Documentation/hostapd#IEEE_802.11i.2FRSN.2FWPA2_pre-authentication
[3] http://wireless.kernel.org/en/users/Documentation/wpa_supplicant#RSN_preauthentication
[4] http://wiki.openwrt.org/doc/recipes/rsn_preauthentication
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
SVN-Revision: 38336
This adds the eap_reauth_period to be used for modifying
the RADIUS server reauthentication authentication period,
a parameter that gets passed directly to the hostapd
configuration file.
Signed-off-by: Mathieu Olivari <mathieu@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
SVN-Revision: 38334
Changes include:
* removing unused variables
* replacing spaces with tabs where appropriate
* more consistency with variable declarations
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 38142
- fixes buffer corruption with JSON-RPC list calls
- change JSON-RPC protocol to include the session ID into the call
attributes instead of passing it via the URL
- forcibly pass effective session ID as "ubus_rpc_session" attribute
to called procedures
- change ubus acl checking to conform with new ubus session namespace
SVN-Revision: 37962
Felix Fietkau
Steven Barth
John Crispin
Hauke Mehrtens
Jo-Philipp Wich
Luka Perkov
Vasilis Tsiligiannis