Commit Graph

47396 Commits (e320435a6a5858e7b80c296c5f5e35d8d4c845b6)

Author SHA1 Message Date
Chuanhong Guo f0f35fdac1 Revert "generic: 5.4: Add 4B_OPCODES flag to w25q256"
This reverts commit d7f21940bc.

Winbond W25Q256FV and W25Q256JV both uses 0xef4019 as JEDEC ID,
but only the latter has proper 4B_OPCODES support.
W25Q256FV has all 4B read instructions but it lacks a 4B page program
instruction, causing the entire flash to be read-only.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-05 12:07:47 +08:00
Tan Zien d24e43a7f6 kernel: Fix miss config and module for mlx driver
Missing config symbols could lead to build failures on kernel
4.14/4.19.

Signed-off-by: Tan Zien <nabsdh9@gmail.com>
[rephrase commit message - reorder symbols]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-04 17:12:43 +02:00
Kevin Darbyshire-Bryant 02640f0147 umdns: suppress address-of-packed-member warning
gcc 8 & 9 appear to be more picky with regards access alignment to
packed structures, leading to this warning in dns.c:

dns.c:261:2: error: converting a packed ‘struct dns_question’ pointer
(alignment 1) to a ‘uint16_t’ {aka ‘short unsigned int’} pointer
(alignment 2) may result in an unaligned pointer value
[-Werror=address-of-packed-member]

261 |  uint16_t *swap = (uint16_t *) q;

Work around what I think is a false positive by turning the warning off.
Not ideal, but not quite as not ideal as build failure.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-04-04 11:28:18 +01:00
Kevin Darbyshire-Bryant c14c6902f5 treewide: convert sed -r to posix -E
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-04-04 11:28:15 +01:00
Thibaut VARÈNE fdac4c085d ath79: improve mikrotik-caldata.sh
Reduce unnecessary flash wear and be tidy:
- Run the extraction only if necessary
- Extract temporary file to /tmp
- cleanup after execution

Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-04-04 11:18:58 +01:00
INAGAKI Hiroshi 817e132332 kernel: rtl8367b: use id as a bit offset for BYPASS_LINE_RATE
In RTL8367B (RTL8367RB/RTL8367R-VB), the driver in GPL tars of the
devices with this switch directly uses the ID of external interface
as a bit offset.

We should use the same way.

ref (RTL8367B):
  - ASUS RT-N56U
  - TP-Link Archer C2 v1

ref (RTL8367):
  - TP-Link TL-WR2543ND v1

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2020-04-04 17:20:13 +08:00
INAGAKI Hiroshi e714cf4195 kernel: rtl8367b: fix DEBUG register address for extif2
RTL8367B_CHIP_DEBUG1_REG (0x1304) is for external interface 1. For
external interface 2, use RTL8367B_CHIP_DEBUG2_REG (0x13e2) instead.

Fixes: 9801d61c4a ("kernel: rtl8367b: add configuration for extif2")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2020-04-04 16:55:47 +08:00
Chuanhong Guo 4d979a4d19 ramips: mt7621: bringup dsa master on preinit
DSA requires master netdev to be up before any of its slave ports.
Bring it up during preinit so that the first lan port can be used
on failsafe.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-04 16:30:16 +08:00
Chuanhong Guo 838f1fbb50 ramips: mt7621: disable image for mikrotik_rbm11g
It's unknown which switch port is used on mikrotik_rbm11g.
Disable this image until someone with actual device fixes this problem.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-04 15:25:36 +08:00
Chuanhong Guo a8d62a4eb1 ramips: remove set_preinit_iface script
This script isn't suitable for mt7621 anymore due to switching to DSA
and it needs a different preinit script.
Generic preinit logic in package/base-files has the ability to parse
board.json and pick preinit iface accordingly. Just remove this script
instead of moving it into subtargets.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-04 14:56:14 +08:00
DENG Qingfang 764cc5c6a6 generic: mt7530: fix null pointer dereferencing in port5 setup
The 2nd gmac of mediatek soc ethernet may not be connected to a PHY
and a phy-handle isn't always available.
Unfortunately, mt7530 dsa driver assumes that the 2nd gmac is always
connected to switch port 5 and setup mt7530 according to phy address
of 2nd gmac node, causing null pointer dereferencing when phy-handle
isn't defined in dts.
This commit fix this setup code by checking return value of
of_parse_phandle before using it.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang 3624721ef1 generic: backport support for MT7530 DSA port mirroring
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
René van Dorst ae6b4d3f86 ramips: correct MTC WR1201 LAN ports names
LAN ports of MTC WR1201 are reversed, so correct their names

Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang 10f27c6f00 ramips: mt7621: add new NAND driver
Add new NAND driver for MT7621

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang 92daa06f22 ramips: mt7621: drop obsolete mx25l25635f dts hack
5.4 kernel has fixed this issue, so the hack is no longer needed.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang 437aaae6ca Revert "ramips: mt7621: disable images for gehua_ghl-r-001"
This reverts commit 28080d54d2.
Support for MX25L25635F flash is fixed upstream

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang dcf7fdbdbf ramips: move swconfig to subtargets except for MT7621
As MT7621 does not use swconfig anymore, move the package swconfig to
other subtargets.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang 6570960913 ramips: mt7621: introduce 'soc_device' initialization
mt7621 SoC has its own 'ralink_soc_info' structure with some
information about the soc itself. Pcie controller and pcie phy
drivers for this soc which are still in staging git tree make uses
of 'soc_device_attribute' looking for revision 'E2' in order to
know if reset lines are or not inverted. This way of doing things
seems to be necessary in order to make things clean and properly.
Hence, introduce this 'soc_device' to be able to properly use those
attributes in drivers. Also set 'data' pointer points to the struct
'ralink_soc_info' to be able to export also current soc information
using this mechanism.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang c24d6111f4 ramips: fix MikroTik 750Gr3 LAN ports names
They are labeled as LAN2..LAN5 instead of LAN1..LAN4

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang 53b66248f4 ramips: use SoC I2C instead of bitbanged for Ubiquiti ER-X-SFP
The original idea of bitbanged I2C is to use i2c-gpio-custom
Since i2c-gpio-custom is no longer available on 5.4, use SoC I2C instead

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang 5acd1ed0be ramips: mt7621: fix Ubiquiti ER-X ports names and MAC addresses
The name of each user port should be eth0..4, instead of lan1..4
and there is no WAN port. Rename them to match the official firmware.
To avoid conflict with the master port (gmac0), rename it to "dsa".

The official firmware assigns MAC address in this way:
eth0 = label mac
eth1 = label mac + 1
...
eth4 = label mac + 4

Since we have switched to DSA, it's possible to use different MAC for each port.

Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang 3211c983fd ramips: mt7621: net-label support
Add support for renaming ethernet interfaces in DTS

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang 1dce5c8a28 ramips: mt7621: switch kernel version to 5.4
After all dts and config changes, 4.14 no longer works on mt7621.
Switch it to 5.4 directly.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang c9f4f765c8 ramips: mt7621: change default ramips_setup_interfaces configuration
Most of MT7621 boards have LAN1~4 and WAN, so make this as the default

Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang d2b9461a55 ramips: mt7621 remove unused pinctrl groups in dts
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[split commit, remove leftover uart3->gpio setup]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-04 14:52:12 +08:00
DENG Qingfang 30644bc579 ramips: mt7621: update dts/defconfig for DSA
update dts and network/LED configuration for DSA driver.
sysupgrade from images prior to this commit with config preserved
will cause broken ethernet setup.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Acked-by: Jo-Philipp Wich <jo@mein.io>
[split commit]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-04 14:40:44 +08:00
DENG Qingfang 7bd19dbe99 ramips: mt7621: backport GPIO driver fix
Backport 2 patches from linux-next to fix mt7621 GPIO driver

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:14:43 +08:00
DENG Qingfang 9ebb85c372 ramips: mt7621: update PCIe node in dtsi
Update PCIe node in dtsi to match the new driver

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:14:43 +08:00
DENG Qingfang d21d6ea454 ramips: mt7621: backport PCIe driver fixes from staging-test
Backport mt7621-pci/mt7621-pci-phy fixes from staging-test

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:14:43 +08:00
DENG Qingfang 66984646c2 ramips: mt7621: update pinctrl nodes
Upstream GPIO driver uses "groups" "function" properties

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:13:05 +08:00
DENG Qingfang 60f691dae4 ramips: mt7621: convert GPIO dts refs
The upstream driver does not use &gpio0..2 banks notation anymore,
so convert them to &gpio

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:13:05 +08:00
DENG Qingfang 783fc8e553 ramips: mt7621: replace gpio/eth nodes in mt7621.dtsi
There's different gpio and ethernet drivers upstream for mt7621.
Update these two nodes to match upstream dt bindings.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:10:58 +08:00
DENG Qingfang 99d210d6a0 ramips: mt7621: refresh kernel config
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 12:04:14 +08:00
DENG Qingfang 6be0da90a1 ramips: refresh patches
Removed upstreamed/solved elsewhere upstream:
- 0001-MIPS-ralink-Add-rt3352-SPI_CS1-pinmux.patch
- 0002-MIPS-pci-rt2880-set-pci-controller-of_node.patch
- 0004-MIPS-ralink-add-MT7621-pcie-driver.patch
- 0009-PCI-MIPS-enable-PCIe-on-MT7688.patch
- 0025-pinctrl-ralink-add-pinctrl-driver.patch
- 0028-GPIO-ralink-add-mt7621-gpio-controller.patch
- 0043-spi-add-mt7621-support.patch
- 0045-i2c-add-mt7621-driver.patch
- 0047-DMA-ralink-add-rt2880-dma-engine.patch
- 0053-mtd-spi-nor-add-w25q256-3b-mode-switch.patch
- 0054-mtd-spi-nor-w25q256-respect-default-mode.patch
- 0099-pci-mt7620.patch
- 304-spi-nor-enable-4B-opcodes-for-mx25l25635f.patch

Removed because of the new NAND driver:
- 0038-Revert-mtd-nand-Remove-unused-chip-write_page-hook.patch
- 0039-mtd-add-mt7621-nand-support.patch
- 0040-nand-hack.patch

Remove patch that no longer applies (needs rework):
- 0034-NET-multi-phy-support.patch

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 12:04:13 +08:00
DENG Qingfang d75c9b8f81 ramips: mtk-mmc: set correct DMA mask
Since commit f8c55dc ("MIPS: use generic dma noncoherent ops for
simple noncoherent platforms") changed MIPS dma handling, the mmc
driver fails because it doesn't have a dma mask is set.

So set the correct dma mask.

Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 12:04:13 +08:00
DENG Qingfang d4903b5720 ramips: move MTK MMC driver to files directory
Move MTK MMC driver from "files-4.14" to "files" so kernel 5.4
can use it

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 12:04:13 +08:00
DENG Qingfang c70545f397 ramips: copy patches and kernel config to 5.4
Copy patches and kernel config to 5.4 for ramips

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 12:04:13 +08:00
Rafał Miłecki b51ea43f90 bcm53xx: refactor board.d code in 02_network
1. Use functions for cleaner code
2. Always execute WAN interface generic code

Before this change WAN interface code wasn't executed on all devices due
to an early "exit 0".

Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2020-04-03 17:59:56 +02:00
Tan Zien 3ec70052c5 kernel: add module for Mellanox mlx Network Driver
add module to support Mellanox Connect-X card
mlx4 supports ConnectX-3 series and previous cards
mlx5 supports Connect-IB/ConnectX-4 series and later cards

Signed-off-by: Tan Zien <nabsdh9@gmail.com>
2020-04-03 15:33:27 +02:00
Tim Harvey ff6b092121 imx6: bootscript: use partition UUID for rootfs if possible
Specifying root filesystem by device is non-deterministic for several
reasons:
 - USB device unmeration order is not garunteeed for USB storage devs
 - MMC devs ordering is determined by the instance of the MMC host
   controller including non-storage SDIO devices which can throw off
   numbering depending on kernel versions.

It is recommended to use partition UUID

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2020-04-03 12:17:45 +02:00
Tim Harvey 4298339b23 octeontx: switch to kernel 5.4
5.4 is stable on Gateworks Newport GW610x/GW620x/GW630x/GW640x

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2020-04-03 12:17:45 +02:00
Paul Spooren 07449f692c build: refactor JSON info files to `profiles.json`
JSON info files contain machine readable information of built profiles
and resulting images. These files were added in commit 881ed09ee6
("build: create JSON files containing image info").

They are useful for firmware wizards and script checking for
reproducibility.

Currently all JSON files are stored next to the built images, resulting
in up to 168 individual files for the ath79/generic target.

This patch refactors the JSON creation to store individual per image
(not per profile) files in $(BUILD_DIR)/json_info_files and create an
single overview file called `profiles.json` in the target directory.

Storing per image files and not per profile solves the problem of
parallel file writes. If a profiles sysupgrade and factory image are
finished at the same time both processes would write to the same JSON
file, resulting in randomly broken outputs.

Some target like x86/64 do not use the image code yet, resulting in
missing JSON files. If no JSON info files were created, no
`profiles.json` files is created as it would be empty anyway.

As before, this creation is enabled by default only if `BUILDBOT` is set.

Tested via buildroot & ImageBuilder on ath79/generic, imx6 and x86/64.

Signed-off-by: Paul Spooren <mail@aparcar.org>
[json_info_files dir handling in Make, if case refactoring]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-03 12:17:45 +02:00
Kevin Darbyshire-Bryant fcd1401700 grub2: fix build when ASLR enabled
Disable ASLR and filter '-fno-plt' from CFLAGS: solves building when
ASLR enabled by basically disabling ASLR.

Solves errors similar to:
relocation R_X86_64_32S against `.rodata' can not be used when making a PIE object; recompile with -fPIE
or
module missing GLOBAL_OFFSET_TABLE

Suggested-by: 李国 <uxgood.org@gmail.com>
Acked-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-04-02 13:42:26 +01:00
Kevin Darbyshire-Bryant b74386acc6 kmod-sched-cake: switch to in-tree cake for 4.19+
Use in tree version of cake for kernels 4.19+ and backport features from
later kernel versions to 4.19.

Unfortunately PROVIDES dependency handling produces bogus circular
dependency warnings so whilst this package and kmod-sched-cake-oot
should be able to PROVIDE kmod-sched-cake this doesn't work.

Instead, remove the PROVIDES option and modify package sqm-scripts to
depend on the correct module independently.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-04-01 21:59:45 +01:00
Kevin Darbyshire-Bryant 475738c9af kmod-sched-cake: rename to kmod-sched-cake-oot
In preparation for dropping the out of tree cake module and using
in tree cake from upstream, rename the package to kmod-sched-cake-oot
(out of tree)

Initially add a PROVIDES kmod-sched-cake so that package dependencies
can be satisfied.

Ultimately this package will be removed when linux 4.14 is removed.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-04-01 21:59:45 +01:00
Jason A. Donenfeld e32eaf5896 wireguard: bump to 1.0.20200401
Recent backports to 5.5 and 5.4 broke our compat layer. This release is
to keep things running with the latest upstream stable kernels.

Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
2020-04-01 22:24:58 +02:00
Daniel Golle a24a9bbc8c mac80211: rt2x00: prune more unnecessary exports
The calibration patches for MT7620 unnecessarily export symbols and
populate never accessed function pointers. Remove all that and make
functions static as the only place where each of those functions is
called is within rt2800lib.c.
Also make code more readable by fixing indentation, removing
unnecessary parantheses and simplifying some instructions using
shorthands here and there.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-04-01 19:47:59 +01:00
Kevin Darbyshire-Bryant 51edc4eb89 jansson: convert to cmake
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-04-01 16:36:04 +01:00
Eneas U de Queiroz af5ccfbac7 openssl: bump to 1.1.1f
There were two changes between 1.1.1e and 1.1.1f:
- a change in BN prime generation to avoid possible fingerprinting of
  newly generated RSA modules
- the patch reversing EOF detection we had already applied.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2020-04-01 08:12:20 +02:00
Daniel Golle 9f14216a2c oxnas: some improvements for Shuttle KD20
* install kmod-hwmon-drivetemp by default
 * wire up thermal zone
 * fix fan GPIO polarity
 * fix i2c-gpio GPIO_OPEN_DRAIN

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-03-31 21:41:23 +01:00