Add support for the EBR-2310, which is almost identical to the DIR-615
rev E4, without the wifi.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
fixes issue "nsa 310b u-boot can initialize usb but cannot
use usb storage so it cannot load files from usb"
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 550/391/195 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x internal antennas (embedded on PCB)
- 9x LED (all can be turned off with GPIO15), 2x button
- UART (J3) header on PCB
Flash instruction: use "factory" image directly in vendor GUI.
Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.
You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin
Image was tested only in US version of the device, but should work
also with the same device version sold in other countries.
Available FLASH space, with LEDE trunk, is only 240 KB.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The WN3000RPv3 is a repeater with a single ethernet port. Setting up the
switch, even to disable it, is unnecessary and possibly confusing.
Configure LAN as eth0 instead.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The list of v2/v3 devices is getting longer and makes reading the names of
the profiles unnecessary hard.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
as we do for IPv4 PPP interfaces. When we create the
dynamic IPv6 interface we should inherit ip6table from
main interface.
Signed-off-by: Ulrich Weber <ulrich.weber@riverbed.com>
pppoe-discovery performs the same discovery process as pppoe, but does
not initiate a session
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Fixes the following issue:
root@LEDE:/# sysupgrade /tmp/lede-mvebu-armada-388-clearfog-sdcard.img.gz
Saving metaconfig...
Image metadata not found
Use sysupgrade -F to override this check when downgrading or flashing to vendor firmware
Image check 'fwtool_check_image' failed.
root@LEDE:/#
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
When running wifi detect, the user will be told on error output that
wifi detect is deprecated, that wifi config must be used instead. Also
the commit that changes it is referenced for further info.
Signed-off-by: David Pinilla Caparrós <dpinitux@gmail.com>
Since commit 5f8f8a3661 wifi detect does
not longer work and wifi config it's used to configure not yet
configured wireless devices.
This commit changes command usage to reflect that change.
Signed-off-by: David Pinilla Caparrós <dpinitux@gmail.com>
The firmware hotplug script tries to read the mac address from a
partition with the name "uboot-env" which does not exist (instead it's
name is uboot_env). This broke calculation of the new checksum (after
patching the mac address) which resulted in ath9k refusing to use the
EEPROM data.
The original error reported by ath9k was:
PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
ath: phy0: Bad EEPROM checksum 0x2523
ath: phy0: Unable to initialize hardware; initialization status: -22
ath9k 0000:00:0e.0: Failed to initialize device
Fixes: a20616863d ("lantiq: use ath9k device tree bindings
binding/owl-loader")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
f107656 netifd: Add option to configure locktime for each device
cdc0e80 interface: add prefix assignment priority support
6397f5e device: add veth support
6228d0f wireless: fix _wireless_add_process
7cc2f10 treewide: fix white space errors
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
platform_find_rootfspart() fails if the kernel partition comes before the
rootfs partition. The proposed patch fixes this while preserving what I
understand was the original idea: stop at first match.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
When running "make kernel_menuconfig" in a clean tree, it fails with:
make[1]: *** No rule to make target 'tools/quilt/install'. Stop.
Replacing the dependency with 'tools/quilt/compile' fixes the issue (quilt
and all its prerequisites will be built, and quilt will be installed in
staging_dir).
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Effects of the bugs could include memory corruption, tx hangs, kernel
crahes, possibly other things as well
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Alexandru Gagniuc
Alberto Bursi
Piotr Dymacz
Furong Xu
Giuseppe Lippolis
Thibaut VARENE
Pavel Kubelun
Sven Eckelmann
John Crispin
Ulrich Weber
Florian Eckert
Jonas Gorski
Felix Fietkau
David Pinilla Caparrós
Yangbo Lu
Chuanhong Guo
Martin Blumenstingl
Hans Dedecker
Koen Vandeputte
Baptiste Jonglez
Hauke Mehrtens