Assign the usbdev trigger via devicetree for all subtargets and drop
the userspace handling of the usb leds.
With the change all usb ports are triggering the usb led instead of
only usb 1.1 XOR usb 2.0 XOR usb 3.0 as it was before.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The former used compatibles aren't defined anywhere and aren't used by
the devicetree source files including them.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add the ranges property to the PCI bridges where missing. Add the unit
address to PCI bridge where missing.
Rework the complete rt3883 pci node. Drop the PCI unit nodes from the
dtsi. They are not used by any dts file and should be rather in the dts
than in the SoC dtsi. Express the PCI-PCI bridge in a clean devicetree
syntax. The ralink,pci-slot isn't used by any driver, drop it. Move the
pci interrupt controller out of the pci node. It doesn't share the same
reg and therefore should be an independent/SoC child node.
Move the pci related rt3883 pinctrl setting to the dtsi instead of
defining the very same for each rt3883 board.
If the device_type property is used for PCI units, the unit is treated
as pci bridge which it isn't. Drop it for PCI units.
Reference pci-bridges or the pci node defined in the dtsi instead of
recreating the whole node hierarchy. It allows to change the referenced
node in the dtsi without the need to touch all dts.
Fix the PCI(e) wireless unit addresses. All our PCI(e) wireless chips
are the first device on the bus. The unit address has to be the bus
address instead of the PCI vendor/device id.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The cpu interrupt controller doesn't have a reg property, hence we
can't use a unit address in the node name.
Signed-off-by: Mathias Kresin <dev@kresin.me>
I found mt7688 watchdog not working. The watchdog registers are identical
for mt7621 and mt7628/mt7688. The first watchdog related register is at
0x10000100, the last one - a 16bit sized - at 0x10000128.
Set the correct register address and size in the dtsi file to get the
watchdog working.
Signed-off-by: lbzhung <gewalalb@gmail.com>
[add commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
In the new USB phy driver, it checks the compatible string before
attempting to iomap its mem resource and do the extra PHY init
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The Ralink USB PHY driver merged into mainline has a slightly different
device tree binding than the patch that was used with linux 4.9.
The new driver requires a `ralink,sysctl` node pointing to the `syscon`
node.
This patch also sets `#phy-cells` to 0, as recommended by the mainline
documentation [1].
[1] Documentation/devicetree/bindings/phy/ralink-usb-phy.txt
Signed-off-by: Vianney le Clément de Saint-Marcq <code@quartic.eu>
Add pinmuxes defined by some board which are including the dtsi files
to the dtsi files itself. Allows to reduce duplication.
Signed-off-by: Mathias Kresin <dev@kresin.me>
mediatek MT7621 soc watchdog DTS id was renamed from "mtk,mt7621-wdt" to
"mediatek,mt7621-wdt" when driver upstreamed to kernel 4.5
Update mt7621.dtsi & mt7628an.dtsi definitions to match upstreamed
kernel.
Restores hardward watchdog functionality on mt7621 devices under linux
4.9
Tested on: MIR3G
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Uses upstream code to parse DT supported band/frequency information.
Update existing .dts files to the new format and remove unnecessary
overrides.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Currently, for RT5350 and MT7628, esw is marked as compatible with
"ralink,rt3050-esw". While this is true, the switches within RT5350
and MT7628 actually support more functionality than the RT3050 switch.
One such example is per-VLAN untagging, which is an important feature.
RT3352 is another example of this, but it already has an additional
compatible property, which allows to differentiate it from RT3050.
This commit adds such more specific properties for RT5350 and MT7628
as well.
Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
This commit makes the following modifications to ramips dts files:
1. Add clkctrl node to all dtsi files (although not used for now)
2. Add clocks and clock-names properties to some nodes (usbphy, pci)
3. Add usbphy node for rt3050 (although not used for now)
4. Add clock-frequency to uart nodes in mt7621.dtsi and mt7628an.dtsi
These modifications, although not fully used at the moment, will make
it easier for FreeBSD to adopt and use LEDE ramips dts files with
minimal changes for easier maintenance.
Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
Add node aliases to dtsi files.
Reword dts files so they're more in-line with upstream.
Fix some more warnings and errors reported by dtc
Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
This patch introduces serial0 aliases in the ramips DTS files, which can
then be used to denote the active console instead of relying on bootargs.
Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
add the SDK alsa driver. this has only been tested on mt7628/88 and wm8960.
mt7620 is only compile tested.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47205
The following patch fixes:
* wrong indentations
* doubled gpio-keys-polled nodes (DIR-300-B7, DIR-320-B1, DIR-610-A1)
* duplicate spacings
* empty lines at end of files and after last child nodes
* trailing and leading whitespace
* unnecessary and commented-out code
* missing empty lines between nodes and between properties and nodes
* unnecessary empty lines between nodes properties [1]
in .dts{,i} files, for ramips target.
[1] Some of empty lines in SOCs dtsi files were left untouched, because they seem to be there for a reason (readability?).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46613
Mathias Kresin
lbzhung
Felix Fietkau
Vianney le Clément de Saint-Marcq
Kevin Darbyshire-Bryant
John Crispin
Michael Lee
Stanislav Galabov
Stanislav Galabov
Felix Fietkau
John Crispin