CT firmware files use the same filename with a different URL for
different chips. Since all files end up in dl/, filenames need to be
unique as well.
Add a chip prefix to the output filename to fix this issue.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
this package references an undefined variable for its submenu.
Remove this NOP variable assignment.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
This board is very old and unlikely to still be relevant today. Support
for it contains a significant amount of device specific baggage which is
worth getting rid of.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add support for NXP layerscape ls1046ardb 64b/32b Dev board.
LS1046ARDB Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 512 Mbyte NAND flash
* Two 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
* On-board 4G eMMC
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe:
* PCIe1 (SerDes2 Lane0) to miniPCIe slot
* PCIe2 (SerDes2 Lane1) to x2 PCIe slot
* PCIe3 (SerDes2 Lane2) to x4 PCIe slot
* USB 3.0: one super speed USB 3.0 type A port, one Micro-AB port
* UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
In order to prevent the impact of the merger of the company and the potential
rebase of the SDK repositories, migrate the u-boot source to github.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
The 10.1 includes a good many stability fixes related to the effort of
backporting upstream 10.2 firmware. Also enables 802.1q vlan support.
Successfully tested on apu2.
The 10.4 firmwares including new backported code as well as stability
fixes. 10.4 has been tested on Fedora x86-64 platforms, but not on LEDE
specifically since I had issues compiling LEDE for my 9980/9984 AP hardware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The QorIQ LS1012A processor, optimized for battery-backed or
USB-powered, integrates a single ARM Cortex-A53 core with a hardware
packet forwarding engine and high-speed interfaces to deliver
line-rate networking performance.
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
LEDE/OPENWRT will auto strip executable program file while make. So we
need select CONFIG_NO_STRIP=y while make menuconfig to avoid the ppfe network
fiemware be destroyed, then run make to build ls1012ardb firmware.
The fsl-quadspi flash with jffs2 fs is unstable and arise some failed message.
This issue have noticed the IP owner for investigate, hope he can solve it
earlier. So the ls1012ardb now also provide a xx-firmware.ext4.bin as default
firmware, and the uboot bootcmd will run wrtboot_ext4rfs for "rootfstype=ext4"
bootargs.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
Add support for NXP layerscape ls1043ardb 64b/32b Dev board.
LS1043a is an SoC with 4x64-bit up to 1.6 GHz ARMv8 A53 cores.
ls1043ardb support features as: 2GB DDR4, 128MB NOR/512MB NAND, USB3.0, eSDHC,
I2C, GPIO, PCIe/Mini-PCIe, 6x1G/1x10G network port, etc.
64b/32b ls1043ardb target is using 4.4 kernel, and rcw/u-boot/fman images from
NXP QorIQ SDK release.
All of 4.4 kernel patches porting from SDK release or upstream.
QorIQ SDK ISOs can be downloaded from this location:
http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
* Backport much of the 10.2 firmware features from upstream QCA driver.
This includes ANI support, adaptive CCA, tx-hang workarounds,
and lots of other things.
Not all of this may be enabled at this point, and more code waits to
be backported as time and motivation allows.
* Fix some rate-control issues where ath10k in station mode (at least), would
sometimes get stuck at low rates. This appeared to be a probe related
state machine issue in the firmware, so I added some timeout logic to kick
the state machine if it gets stuck. This signicantly improves throughput
tests with many stations.
* Support configuring WMI WD timeout using SET_SPECIAL API.
* Properly configure the rx-mask on bootup to work around problem found
by Mr. Kazior. This should remove the need to add the driver hack he
posted.
* Allow configuring pdev failed-retry threshold. This is how many consecutive
tx failures the firmware will allow before resetting the wifi chip (not a full
firmware crash).
Signed-off-by: Ben Greear <greearb@candelatech.com>
* Change git packages to xz
* Update mirror checksums in packages where they are used
* Change a few source tarballs to xz if available upstream
* Remove unused lines in packages we're touching, requested by jow- and blogic
* We're relying more on xz-utils so add official mirror as primary source, master site as secondary.
* Add SHA256 checksums to multiple git tarball packages
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Now that the firmware for BCM43430 has been submitted to linux-firmware use it
and remove RPiDistro package.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This patch moves the ath10k firmware packages to the firmware submenu
in the buildroot, where it belongs.
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
Use firmware version 10.2.4.70.54 from kvalo's git repository. The old
version (even though it's version number is greater) is an old version
from September 2015.
Using only the firmware versions from kvalo's git repo is recommended,
because those are tested by QCA's internal QCA.
The QCA988X directory received a small reorganization as a "hw2.0"
subdirectory was added - this patch also takes care of that as
board.bin was moved to that subdirectory.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Adds Google's mirrors as primary source and kernel.org as fallback.
Discussed in #lede-dev on Freenode
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Update the linux-firmware package in order to force the buildbots to fetch the
proper mirrored version.
Currently each builder has its own copy of the linux-firmware checkout staged
in its own dl/, since the package was updated before the mirrored copy has
been uploaded. The builders then subsequently uploaded their own copy instead,
leading to md5sum mismatches since each clone produces different tarballs.
By bumping the package to a new version and uploading the mirrored archive
with the proper md5sum beforehand, the builders will fetch that instead and
not upload their own copies.
To properly solve that problem in the future we need to ensure that packed
checkouts become reproducable.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Since the md5sum of the mirrored Git clone archive has been set in the Makefile
before that particular archive was uploaded to the source mirror, the buildbots
uploaded their own, different copy instead invalidating the mirror md5sum for
anyone else.
In order to fix the mismatch, update the md5sum to reflect the archive being
present on the download server.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The Annex A firmware will be updated to:
05.08.01.08.01.06_05.08.00.0B.01.01_osc
The Annex B firmware will be updated to:
05.07.09.09.00.06_05.07.04.04.00.02_osc
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Using few packages will allow saving some space by decreasing rootfs
size.
Moreover there are more firmware files that may require packaging and
even more to come later.
This can especially useful now, with per device rootfs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Using few packages will allow saving some space by decreasing rootfs
size. Dropping 43602a1 firmware saves 316 580 B. Dropping 4366b1 saves
468 188 B.
Moreover there are more firmware files that may require packaging and
even more to come later (e.g. 4366c0).
This can especially useful now, with per device rootfs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tested briefly on Netgear r7800. Firmware failed to load on first
boot, but then it worked after that and I could not reproduce the
failure.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Among other things, this compiles out support for peer caching.
The feature did not seem to work well in my testing of AP mode,
and totally breaks my own special use of station mode.
Briefly tested on ea8500.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This firmware has been lightly tested on non LEDE system
to date, and will be undergoing further testing and development.
Allow users to easily install this on their LEDE system as
they prefer.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This lets one use the CT ath10k driver instead of the built-in
ath10k driver from the upstream kernel (or backports).
This should be a drop-in replacement, as well as enabling
better CT firmware support.
Signed-off-by: Ben Greear <greearb@candelatech.com>
There are multiple prism54/p54 firmware versions for different
drivers and devices. Therefore, assigning the package version
of all the different firmware packages on the old prism54
firmware could break if any of the p54 firmwares are updated
and we need to roll out new packages.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[removed PKG_VERSION]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use first caldata for devices without OTP. The driver uses the caldata
instead of the board.bin data anyway
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Instead of downloading the firmware for prism54 devices in the
wireless.mk do it in an extra package Makefile. To ship the complete
source code Intel ships our modified OpenWrt/LEDE + the content of the
dl directory. We do not want to have any files in the dl/ directory
which are not needed to build our images. The prism54 gets downloaded
every time independently of building kmod-net-prism54 or not. When it
is in a own package it only gets downloaded when the firmware package
is selected.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
The copy on the mirror has a different md5sum as specified in this
package Makefile. The content of the file on the mirror is the same as
in the checkout so just update our md5sum.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of downloading the firmware from some website take it from
linux-firmware package and do not download it separately any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In company networks everything except the http and https protocol is
often causes problems, because the network administrators try to block
everything else. To make it easier to use LEDE in company networks use
the https/http protocol for git access when possible.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Original URL got 303 redirect which then also dropped the commit id
leading to different file revision & MD5 mismatch.
Corrected URL & clarified commit ID use in Makefile
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
This allows one to select CT firmware for ath10k
if one prefers to try this firmware instead of stock
ath10k firmware.
The 10.1 (988X) firmware can actually be installed beside the
default firmware, but it will not be used as long as the firmware-5.bin
file exists. Users could rename the files and reboot to use different
images.
The 99X0 (wave-2) firmware uses the same firmware-5.bin name as default
firmware, so it cannot be installed at the same time as default firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Add nonshared flag to package depending on specific targets or subtargets as
there's no guarantee otherwise that they'll be available in the shared repo.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This adds the firmware needed for the BCM43438 included in Raspberry Pi 3.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 49102
Some parts of this package were named rt73-pci-firmware before which
looks like a copy and past error. This renames all parts to rt73-usb-
firmware and then the firmware gets build and the dependencies from the
package with the kernel module are also working correctly.
This fixes#22069
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49037
Instead of having two big binaries only add one binary and then a patch
to create the other one when needed at runtime.
This is easier to handle in one Makefile for both firmware files.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48939
This adds option to build kernel module and firmware packages
for a Marvell 8686 SPI Wireless device
Signed-off-by: Joseph Honold <mozzwald@gmail.com>
SVN-Revision: 48750
This just renamed the package to indicate that this is the annex a version.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
SVN-Revision: 47649
Updates the ath10-firmware release to current git and updates the
QCA988X firmware in use to version 10.2.4.70.12-2 which appears to
actually fix the stability problems when using a Nexus 5X phone as
per issue #20854. Also updates the Makefile for a change in the
location of the board.bin file for QCA988X in the source repository.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
SVN-Revision: 47469
Updates the ath10k firmware version for QCA988X to version
10.2.4.70.10-2, which appears to fix problems with the 5GHz wireless
failing on TP-Link Archer C7 v2 when using a Nexus 5X phone. Fixes
issue #20854.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
SVN-Revision: 47454
Felix Fietkau
Alberto Bursi
Yutang Jiang
Ben Greear
Daniel Engberg
Pavel Kubelun
Álvaro Fernández Rojas
Stijn Segers
Martin Blumenstingl
diizzyy
Jo-Philipp Wich
Hauke Mehrtens
Rafał Miłecki
Zhao Gang
Christian Lamparter
Hauke Mehrtens
Kevin Darbyshire-Bryant
John Crispin
Felix Fietkau
Rafał Miłecki
Luka Perkov
Zoltan Herpai