Commit Graph

1185 Commits (daca6a6a97f89214b6fbfccf7989b4c17bde3da6)

Author SHA1 Message Date
Gabor Juhos c8b9086ac5 ar71xx: build image for the Buffalo WHR-HP-G300N
Based on a patch by Yoichi Shinoda <shinoda@jaist.ac.jp>

SVN-Revision: 28568
2011-10-24 21:49:29 +00:00
Gabor Juhos 9d51cda2db ar71xx: Buffalo WHR-HP-G300N kernel support
The initial support for the Buffalo WHR-HP-G300N box.
The code was confirmed to boot and run, but not tested in depth.

Known problem: iw phy phy0 info shows:
	Coverage class: 0 (up to 0m)
	Available Antennas: TX 0 RX 0

Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>

SVN-Revision: 28567
2011-10-24 21:49:26 +00:00
Gabor Juhos 0ab6be2ba3 ar71xx: build image for the Allnet ALL0258N board
Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 28565
2011-10-24 21:49:23 +00:00
Gabor Juhos d96e321bd1 ar71xx: add kernel support for the Allnet ALL0258N board
This patchs adds support for the Allnet ALL0258N outdoor AP/bridge.
The ALL0258N is based on the AR7240 SoC paired with an AR9285 radio,
it got 8MB of NOR and 32MB SDRAM.

Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 28564
2011-10-24 21:49:21 +00:00
Gabor Juhos ef41e0a61c ar71xx: don't override CONFIG_FSNOTIFY
SVN-Revision: 28563
2011-10-24 21:49:18 +00:00
Jo-Philipp Wich b61de9c865 base-files: make sure inittab-console-fixup returns with success (#10275)
SVN-Revision: 28562
2011-10-24 21:35:43 +00:00
Jonas Gorski a136b67604 linux: ar71xx: add support for Mikrotik Routerboard RB493G
SVN-Revision: 28423
2011-10-11 23:05:16 +00:00
Jonas Gorski 03f91068d1 ar71xx: add a workaround for ar8316 not always driving the TA bit to low
AR8316 behind a GPIO bitbanged MDIO bus fails to drive the turnaround bit
to low despite returning a valid value. Ignore it and just use the
returned value anyway.

SVN-Revision: 28422
2011-10-11 23:05:13 +00:00
Jonas Gorski c674c874b7 ag71xx: close a race between the phy state machine and link state
A fast stop/start cycle could leave the ag71xx interrupts and tx engine
disabled when using a phy driver with a fixed link and the start/stop
happens between two phy state machine polls.

Prevent this by always forcing the link down on stop regardless of phy
state and having a phy connected.

SVN-Revision: 28380
2011-10-08 11:37:14 +00:00
Gabor Juhos 6ac4156136 ar71xx: fix MAC addresses on the DIR-825-B1 board
Patch-by: Lukas Kuna

SVN-Revision: 28295
2011-09-23 19:56:39 +00:00
Gabor Juhos e45d7d7006 ar71xx: enable login only on the system console by default
SVN-Revision: 28294
2011-09-23 19:56:38 +00:00
Gabor Juhos 49ac36e818 ar71xx: build images for the TP-Link TL-WR703N v1 board
Based on a patch by dongyuqi <729650915@qq.com>

SVN-Revision: 28279
2011-09-21 11:47:56 +00:00
Gabor Juhos 733399600f ar71xx: add support for the TP-Link TL-WR703N v1 board
Based on a patch by dongyuqi <729650915@qq.com>

SVN-Revision: 28277
2011-09-21 11:47:53 +00:00
Gabor Juhos d3617ac7d3 ar71xx: add AR933x specific USB setup function
SVN-Revision: 28276
2011-09-21 11:47:51 +00:00
Gabor Juhos 91340d8af7 ar71xx: add ar71xx_device_reset_rmw helper
SVN-Revision: 28275
2011-09-21 11:47:50 +00:00
Gabor Juhos 9fa51d5c38 ar71xx: fix copy&paste bug in WZRHPAG300H profile description
SVN-Revision: 28274
2011-09-21 11:47:48 +00:00
Gabor Juhos 079e746fc4 ar71xx: remove 'default [yn]' from machine Kconfig entries
SVN-Revision: 28273
2011-09-21 11:47:47 +00:00
Gabor Juhos 73dac07c44 ar71xx: sort AR71XX_MACH_* entries
SVN-Revision: 28272
2011-09-21 11:47:45 +00:00
Gabor Juhos ef2431c8d9 ar71xx: create image for the TP-Link TL-WR743ND v1
Same hardware as WR741ND but with PoE support.

Signed-off-by: Paul Fertser <fercerpav@gmail.com>

SVN-Revision: 28271
2011-09-21 11:47:44 +00:00
Gabor Juhos 76d0d1a837 ar71xx: create image for the TP-Link TL-WR740N v3
Signed-off-by: Martin Raykov <martin.raykov@gmail.com>

SVN-Revision: 28269
2011-09-21 11:47:40 +00:00
Felix Fietkau 1bdf65f580 ar71xx: fix register range check for DMA stuck checks (thx, Frédéric Moulins)
SVN-Revision: 28213
2011-09-11 17:44:12 +00:00
Felix Fietkau 65d809ef19 ar71xx: do not count normal interrupts as spurious (fixes #10037)
SVN-Revision: 28182
2011-09-06 05:38:23 +00:00
Felix Fietkau de8cabe839 ar71xx: clean up profiles, put in kmod-ath9k and wpad-mini by default (fixes #9954)
SVN-Revision: 28173
2011-09-05 18:37:48 +00:00
Felix Fietkau cd2c68501c ar71xx: fix ethernet PLL setting on ar7242
SVN-Revision: 28124
2011-08-29 21:23:46 +00:00
Hauke Mehrtens 09b1073f9b kernel: update kernel to version 2.6.39.4
SVN-Revision: 28022
2011-08-16 22:04:10 +00:00
Felix Fietkau 12c84f8eeb ar71xx: add some code to detect DMA stuck conditions on ar7240
SVN-Revision: 27975
2011-08-13 22:30:14 +00:00
Felix Fietkau 85ccc74e1b ar71xx: on ar724x only reset the link status in the restart handler, the fast reset takes care of DMA stuck issues
SVN-Revision: 27973
2011-08-13 21:49:46 +00:00
Felix Fietkau d26bb6c59c ar71xx: adjust the mtd layout of tew-632brp and dir-615c to match the image layout (fixes #9922)
SVN-Revision: 27959
2011-08-11 13:52:40 +00:00
Jonas Gorski def60e2918 ar71xx: make ehci patch apply again
SVN-Revision: 27951
2011-08-10 23:02:56 +00:00
Felix Fietkau 9e5ead9a51 ar71xx: fix a copy&paste bug that broke wzr-hp-g300nh and wzr-hp-ag300h images (#9918)
SVN-Revision: 27950
2011-08-10 22:24:56 +00:00
Gabor Juhos 7e5a1bc1d0 ar71xx: fix image generation
SVN-Revision: 27907
2011-08-05 10:31:52 +00:00
Gabor Juhos 85b858fae6 ar71xx: enable sysupgrade on the AP96 and DB120 boards
SVN-Revision: 27901
2011-08-04 19:41:18 +00:00
Gabor Juhos fb77134596 ar71xx: use the same test for AP121 and Zcomax sysupgrade images
SVN-Revision: 27900
2011-08-04 19:41:17 +00:00
Gabor Juhos fd3a5f64f2 ar71xx: cleanup image generation Makefile
SVN-Revision: 27899
2011-08-04 19:41:16 +00:00
Felix Fietkau 4b75394056 ar71xx: fix ethernet FIFO state corruption on ar7240
When starting/stopping DMA sometimes the FIFO state gets corrupted,
leading to wildly fluctuating latencies or packet data corruption.
Fix this by issuing a fast MAC reset as soon as the link is detected
as up. Fixes #9689, #9405

SVN-Revision: 27896
2011-08-04 17:36:31 +00:00
Felix Fietkau d2aeca6b6d ag71xx: fix memory corruption issues on ar7240 on ethernet start/stop
When the DMA engine state gets corrupted due to a hardware issues, it
often won't stop rx until a full reset is issued. In that case the hardware
must keep a valid descriptor, otherwise it will write to random places in
system RAM, triggering random crashes. To fix this, keep a dummy descriptor
without a buffer that keeps the DMA engine in a sane state until the reset
is done

SVN-Revision: 27895
2011-08-04 17:36:27 +00:00
Felix Fietkau 500c3a1475 ar71xx: fix MAC/MDIO reset mask handling
SVN-Revision: 27894
2011-08-04 17:36:23 +00:00
Felix Fietkau 54d97e6782 ar71xx: add some hacks to work around the misalignment in IP packets received on AR71xx and AR91xx ethernet MACs decreases CPU load with the default firewall for routing 95 mbit/s from 78% to 55%
SVN-Revision: 27878
2011-08-02 15:12:08 +00:00
Jonas Gorski e18ceb1dac ar71xx: merge WZR-HP-G301NH support into WZR-HP-G300NH
Now that we can use a generic name for the switch there is no need for a
separate image for the WZR-HP-G301NH.
Update the default network config and remove the extra image.

SVN-Revision: 27814
2011-07-28 11:57:51 +00:00
Felix Fietkau 9e4113b493 ar71xx: autodetect rtl8366s/rtl8366rb on wzr-hp-g300nh
SVN-Revision: 27756
2011-07-24 14:40:35 +00:00
Felix Fietkau 1afe8a0726 rtl8366: unify rtl8366s and rtl8366rb platform data
SVN-Revision: 27754
2011-07-24 14:40:23 +00:00
Felix Fietkau 9105dad418 ar71xx: enable the usb power regulator on the wzr-hp-ag300h through gpio 2 (#9684)
SVN-Revision: 27739
2011-07-24 08:02:20 +00:00
Felix Fietkau c7173a211d ar71xx: reinitialize global switch settings after reset on ar7240
SVN-Revision: 27705
2011-07-20 14:39:47 +00:00
Felix Fietkau ca473833c4 ar71xx: configure address aging on ar7240
SVN-Revision: 27704
2011-07-20 14:39:42 +00:00
Felix Fietkau fefc79f3cb ar71xx: reset the phy in the ethernet init on ar724x
SVN-Revision: 27703
2011-07-20 12:04:34 +00:00
Felix Fietkau 005fe5d1fd ar71xx: make sure that rx and interrupts are disabled before issuing the hardware reset
SVN-Revision: 27702
2011-07-20 12:04:29 +00:00
Felix Fietkau e7ab000008 ar71xx: increase the delay after the ethernet MAC reset
SVN-Revision: 27701
2011-07-20 12:04:25 +00:00
Felix Fietkau 255dcaa3a6 ar71xx: fix an unused variable warning
SVN-Revision: 27700
2011-07-20 12:04:20 +00:00
Felix Fietkau f3d693c0ee ar71xx: do not reset the hardware on transmit timeout - this would mess up the up the PHY state
SVN-Revision: 27568
2011-07-09 06:30:13 +00:00
Felix Fietkau 2806c75c07 ag71xx: keep the rx engine stopped while the link is not up, should hopefully fix stability issues from #9405
SVN-Revision: 27567
2011-07-09 06:29:46 +00:00
Gabor Juhos 5ad4040c49 ar71xx: build image for the AP121 boards with 4M of flash
SVN-Revision: 27523
2011-07-07 13:01:50 +00:00
Gabor Juhos cdcb10ee42 ar71xx: add separate profiles for the AP121 and AP121-MINI boards
SVN-Revision: 27522
2011-07-07 13:01:48 +00:00
Gabor Juhos 89f6b29feb ar71xx: fix building of squashfs images
SVN-Revision: 27446
2011-07-04 12:10:03 +00:00
Felix Fietkau 7afed2d86c ar71xx: add wzr-hp-ag300h sysupgrade support (patch from #9650)
SVN-Revision: 27434
2011-07-04 03:03:34 +00:00
Gabor Juhos b3a89652a5 ar71xx: use 4k image only for the AP121 board
Create optimized 64K images with the new padjffs2 tool and use that
images instead of the 4k ones. The 4k images causes problems on devices
where the flash erase size is 64 KB.

SVN-Revision: 27357
2011-07-02 08:37:59 +00:00
Jo-Philipp Wich 701543d3ef revert r27043 (#9513)
SVN-Revision: 27343
2011-07-01 19:52:57 +00:00
Jo-Philipp Wich 1edef5ec98 revert r27341, it introduce wrong behaviour for other models
SVN-Revision: 27342
2011-07-01 19:15:45 +00:00
Jo-Philipp Wich 3b3103b2f1 turn status LED off if device finished initializing
SVN-Revision: 27341
2011-07-01 18:39:53 +00:00
Gabor Juhos f9e4619b97 ar71xx: remove CONFIG_MTD_CONCAT ifdefs from the WZR-HP-AG300H code
The config option has been removed in 2.6.39.

SVN-Revision: 27320
2011-06-30 12:15:33 +00:00
Gabor Juhos d98476c6bd ar71xx: merge 2.6.39 patches
Also remove the old UART driver for ar933x.

SVN-Revision: 27314
2011-06-29 08:57:37 +00:00
Gabor Juhos 74a88749f3 ar71xx: remove 2.6.37 support as well
SVN-Revision: 27313
2011-06-29 08:57:36 +00:00
Gabor Juhos 1d5378f588 ar71xx: remove 2.6.38 support
SVN-Revision: 27312
2011-06-29 08:57:34 +00:00
Gabor Juhos 36e7a8b33e ar71xx: switch to 2.6.39
SVN-Revision: 27311
2011-06-29 08:57:33 +00:00
Gabor Juhos 6627574e57 ar71xx: add 2.6.39 support
SVN-Revision: 27310
2011-06-29 08:57:32 +00:00
Gabor Juhos 1e138098cd ar71xx: remove ar71xx_gpio_irq_set_type
SVN-Revision: 27309
2011-06-29 08:57:30 +00:00
Gabor Juhos 055e317ed8 ar71xx: add separate handlers for IP3 interrupts
SVN-Revision: 27308
2011-06-29 08:57:29 +00:00
Gabor Juhos 59bff8bf18 ar71xx: use separate handlers for IP2 interrupts
SVN-Revision: 27307
2011-06-29 08:57:28 +00:00
Gabor Juhos 9d6af600e1 ar71xx: remove useless irq_desc.status initializations
SVN-Revision: 27306
2011-06-29 08:57:27 +00:00
Felix Fietkau cc56af716c ar71xx: add default network config for wzr-hp-ag300h (based on a patch from #9607)
SVN-Revision: 27283
2011-06-25 13:54:42 +00:00
Felix Fietkau ed7f41792a ar71xx: bring up secondary radio on wzr-hp-ag300h (fixes #9608)
SVN-Revision: 27282
2011-06-25 13:48:47 +00:00
Gabor Juhos e6af77a1c8 ar71xx: cleanup AR933X UART driver
SVN-Revision: 27222
2011-06-19 13:17:51 +00:00
Gabor Juhos 066e04d497 ar71xx: fix uart clock frequency for AR933X
SVN-Revision: 27221
2011-06-19 13:17:50 +00:00
Gabor Juhos b7e016ba42 ar71xx: use ar933x_uart.h in the AR933X serial driver
SVN-Revision: 27166
2011-06-13 08:12:40 +00:00
Gabor Juhos b58ede16a5 ar71xx: update early_printk code
SVN-Revision: 27165
2011-06-13 08:12:38 +00:00
Vasilis Tsiligiannis 70106f153d Remove trailing spaces, convert spaces to tabs
SVN-Revision: 27153
2011-06-09 19:30:50 +00:00
Felix Fietkau 9160e06af5 ar71xx: override inittab to enable login on ttyATH0
SVN-Revision: 27128
2011-06-07 17:07:10 +00:00
Gabor Juhos 13363d9129 ar71xx: setup wdt_clock for AR913X to avoid a kernel bug
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>

SVN-Revision: 27102
2011-06-04 12:30:10 +00:00
Gabor Juhos ae2cbfa1e8 ar71xx: select the internal antenna by default on the ZCN-1523H boards
SVN-Revision: 27101
2011-06-04 12:30:09 +00:00
Felix Fietkau 31dd60689e Revert "ar71xx: only enable the rx engine after the link is up..."
It messes up the DMA state when the link goes down

SVN-Revision: 27088
2011-06-01 18:15:43 +00:00
Gabor Juhos 750af1522b ar71xx: init external_reset for AR933X
SVN-Revision: 27083
2011-06-01 13:12:30 +00:00
Gabor Juhos af4cae4498 ar71xx: add external_reset field to ath9k_platform_data
SVN-Revision: 27082
2011-06-01 13:12:28 +00:00
Gabor Juhos f0c7b93e5d ar71xx: init get_mac_revision on AR9330 rev 1
SVN-Revision: 27081
2011-06-01 13:12:27 +00:00
Gabor Juhos 1a54e33c17 ar71xx: add get_mac_revision to ath9k_platform_data
SVN-Revision: 27080
2011-06-01 13:12:26 +00:00
Gabor Juhos 34ff32a6eb ar71xx: export SoC revision
SVN-Revision: 27079
2011-06-01 13:12:24 +00:00
Felix Fietkau 86dbc3a02d ar71xx: add profile and image building code for wzr-hp-ag300h
SVN-Revision: 27076
2011-06-01 02:23:30 +00:00
Felix Fietkau 4f06b8263a ar71xx: add kernel support for the buffalo wzr-hp-ag300h
SVN-Revision: 27075
2011-06-01 02:23:26 +00:00
Gabor Juhos 33fdc21d40 ar71xx: build images for the AP121 boards
SVN-Revision: 27070
2011-05-31 22:53:47 +00:00
Gabor Juhos 9e435c03e0 ar71xx: add sysupgrade support for the AP121 boards
SVN-Revision: 27069
2011-05-31 22:53:45 +00:00
Gabor Juhos 646937135f ar71xx: add default network config for the AP121 boards
SVN-Revision: 27068
2011-05-31 22:53:44 +00:00
Gabor Juhos f332dbd7be ar71xx: add support for the AP121/AP121-MINI reference boards
SVN-Revision: 27067
2011-05-31 22:53:43 +00:00
Gabor Juhos 8beff081eb ar71xx: register UART for the AR933X SoCs
SVN-Revision: 27066
2011-05-31 22:53:42 +00:00
Gabor Juhos b460bc6f12 ar71xx: add serial driver for the AR933X UART
SVN-Revision: 27065
2011-05-31 22:53:40 +00:00
Gabor Juhos c34e0cbc4c ar71xx: add WMAC initialization code for the AR933X SoCs
SVN-Revision: 27064
2011-05-31 22:53:39 +00:00
Gabor Juhos e8a0aaf9a2 ar71xx: add ethernet initialization for the AR933X SoCs
SVN-Revision: 27063
2011-05-31 22:53:37 +00:00
Gabor Juhos e0a0f3796a ar71xx: enable USB support for the AR933x SoCs
SVN-Revision: 27062
2011-05-31 22:53:36 +00:00
Gabor Juhos 677c80ee17 ar71xx: add AR933x specific glue for ar71xx_device{start,stop}
SVN-Revision: 27061
2011-05-31 22:53:35 +00:00
Gabor Juhos 88c45e3130 ar71xx: the watchdog uses the reference clock on the AR933x SoCs
SVN-Revision: 27060
2011-05-31 22:53:34 +00:00
Gabor Juhos 7acbacab8c ar71xx: add AR933x specific glue code for IRQ initialization
SVN-Revision: 27059
2011-05-31 22:53:32 +00:00
Gabor Juhos e6fde61bec ar71xx: don't register 8250 UART on the AR933x SoCs
SVN-Revision: 27058
2011-05-31 22:53:31 +00:00
Gabor Juhos 8f7541a044 ar71xx: enable GPIO support for the AR933x SoCs
SVN-Revision: 27057
2011-05-31 22:53:30 +00:00