The tftp.bin image for Buffalo WHR-G300N was not built, so I was fixed
it after rewriting to new image build code. And the code for
factory-EU.bin was broken, so I deleted it.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
- Remove kernel 4.9 support
- Apply specific 4.14 changes directly to source
- Refreshed all
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The Cavium OCTEON TX is an ARM 64-bit SoC leveraging CPU cores and
periperhals from the Cavium ThunderX SoC.
This initial support provides a 4.14 kernel and kernel+initramfs that is
bootable on the Gateworks Newport GW630x as well as the Cavium sff8104
reference board.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Device Tree file for I2SE Duckbill boards was updated upstream.
Let's use the upstream version for upcoming kernel 4.14 by keeping
our current version for v4.9 still around.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
The GnuBee Personal Cloud Two crowdfunded on https://www.crowdsupply.com
It is a low-cost, low-power, network-attached storage device.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: DDR3 512 MB
- Flash: 32 MB
- Six SATA ports for 3.5" Drives
- One SDcard
- One USB 3.0
- Two USB 2.0
- Gigabit Ethernet: Three Ports
- UART 3.5mm Audio Jack or 3 pin header - 57600 8N1
- Three GPIOs available on a pin header
Flash instructions:
The GnuBee Personal Cloud Two ships with libreCMC installed.
libreCMC is a Free Software Foundation approved fork of LEDE/OpenWrt.
As such one can upgrade using the webinterface or sysupgrade.
Das U-Boot has multiple options for recovery or updates including :
- USB
- http
- tftp
Errata:
- While there are three ethernet ports, the third requires support for
the second GMAC. This will come in kernel 4.14.
- The first hard drive slot has a clearance issue with the two fan
headers. Workaround is to pull the headers out and connect the pins to
jumper wires.
- Using this device as a NAS is problematic with the 4.9 kernel as many
/dev/sdX reads throw silent errors. The current theory behind this is
some kind of unhandled DMA mapping error in the kernel. This is not an
issue with kernel 4.4.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Updated pfe kernel patch to clean up iounmap(pfe->ddr_baseaddr).
pfe->ddr_baseaddr was got through phys_to_virt() not ioremap(),
so iounmap() for pfe->ddr_baseaddr should be removed.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to add a known issue of make menuconfig
in README file. This is also a common issue for OpenWrt.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch changes the declarations of ndo_get_stats64 handlers
to the previous struct rtnl_link_stats64 * return type instead of
the mainline void return.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tis patch is to fix up some descriptions in README.
Per-device rootfs had been supported, and a known issue
had been found. These also should be updated accordingly.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Some layerscape devices (ls1012ardb/ls1012afrdm/ls1046ardb/ls1088ardb)
were using ext4 rootfs because there were issues using squashfs.
This patch is to drop using ext4 rootfs and use ubifs rootfs instead
which is more proper for SPI-NOR flash.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to remove USB configs for 32-bit device since
they're already in kmod package. Also removed TI platform
specific configs.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Patches changes
- Updated patches-4.9 to NXP LSDK1712 linux-4.9.
- Merged changes of patch 303 into integrated patch 201.
- Split changes of patch 706 into dpaa part and dpaa2
part, and merged these changes into integrated patches
701 and 705.
- Removed patch 819 since ehci-fsl driver could be compiled now.
- Refreshed these patches.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This device is identical as TP-Link RE450
RE355 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9558+QCA9880.
Specification:
720/600/200 MHz (CPU/DDR/AHB)
64/128 MB of RAM (DDR2)
8 MB of FLASH (SPI NOR)
3T3R 2.4 GHz
3T3R 5 GHz
1x 10/100/1000 Mbps Ethernet
7x LED, 3x button
UART header on PCB
Flash instruction:
Web:
Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin
and use OEM System Tools - Firmware Upgrade site.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
This will introduce a warning on 3.18, but fixes an error when
compiling for 4.9.
Fixes: cf9e0a59aa ("ar7: add kernel 4.9 support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
When clearfog was renamed to clearfog pro, it broke sysupgrade from
17.04 as the new images now get rejected as incompatible. Fix this by
adding the legacy boardname to the compatible devices.
Fixes: ec4a8c6dee ("mvebu: ClearFog renamed upstream to ClearFog Pro")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Add support for kernel 4.9 based on the more upstream comformant
partition defintions. Increases compressed kernel size by ~95k
compared to 4.4.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Partitions are supposed to be enclosed in an extra partitions node. Allow
the bcm63xxpart parser to cope with that.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The lookup needs to be called just "reset" for the common code.
Fixes: 054c0d4e31 ("brcm63xx: backport mdio-bus reset gpio support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The arm CPUs uses in the supported Mediatket SoCs have a FPU accordingly
to the datasheet, activate it also. The CPU subtype "neon-vfpv4" is
selected, but the toolcahin generated for this SoC will still be
compiled with soft float and not with the hard float ABI as we haven't
the fpu feature flag set. If this toolchain is reused by other targets
this will even affect other targets.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The BDFs for OpenMesh A42 were upstreamed [1] to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-01-26. The
ipq-wifi-openmesh_a42 package can now be dropped because OpenWrt already
ships the QCA4019 board-2.bin from this version.
[1] https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
COMFAST CF-E375AC is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9563 + QCA9886 + QCA8337.
Short specification:
2x 10/100/1000 Mbps Ethernet, with PoE support
128MB of RAM (DDR2)
16 MB of FLASH
3T3R 2.4 GHz, 802.11b/g/n
2T2R 5 GHz, 802.11ac/n/a, wave 2
built-in 5x 3 dBi antennas
output power (max): 500 mW (27 dBm)
1x RGB LED, 1x button
built-in watchdog chipset
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Ding Tengfei <dtf@comfast.cn>
TP-Link Archer C50 v3 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7612E.
Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power switch
* WAN LED in this devices is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Flash instruction:
The only way to flash LEDE image in ArcherC50v3 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt7628-ArcherC50v3-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
The D-Link devices with JBOOT bootloader use their own kernel
image header (stag + sch2 headers).
This driver find jImage header and set rootfs start after kernel file.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This commit marks the CPUs switchport explicit as untagged.
Otherwise, an eth0.1 interface is created and the devices
LAN-ports are not working.
Signed-off-by: David Bauer <mail@david-bauer.net>
Use "$(DTS_DIR)", defined at include/image.mk, instead of
"$(LINUX_DIR)/arch/$(LINUX_KARCH)/boot/dts" in order to generalize and
allow a better Device/* device-tree parameterization (i.e. DEVICE_DTS_DIR
and DTS_DIR).
Signed-off-by: Adrià Llaudet <adria.llaudet@gmail.com>
Update Linux kernel version from 4.9 to 4.14 for archs38.
config-4.14 was simply regenerated with "make kernel_menuconfig".
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: John Crispin <john@phrozen.org>
This config option was renamed in upstream Linux commit 681bec0367
("tracing: Rename update the enum_map file")
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Convert userspace code to use generic device-tree compatible board
detection method. Users of the existing code will have to use
sysupgrade -F once to switch to the new generic board naming.
Properly setup pinctrl fixing the switch port LEDs.
Fixes commit 9c4fe103cb (ramips: add support for ZBT-WE1226)
Reported-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
INAGAKI Hiroshi
John Crispin
Koen Vandeputte
Tim Harvey
Michael Heimpold
Rosen Penev
Yangbo Lu
Henryk Heisig
Jonas Gorski
Matthias Schiffer
Hauke Mehrtens
Sven Eckelmann
Ding Tengfei
David Bauer
Pawel Dembicki
Zoltan HERPAI
Arne Zachlod
Adrià Llaudet
Evgeniy Didin
Felix Fietkau
Stijn Tintel
Daniel Golle