8b9931fd27
ar71xx: add support for the TL-WDR4300 board
...
SVN-Revision: 32459
2012-06-19 11:51:17 +00:00
e6a10d5cdd
ar71xx: refresh patches
...
SVN-Revision: 32458
2012-06-19 11:51:15 +00:00
86c6543259
ar71xx: make AR8327 LEDs working on the DB120 board
...
SVN-Revision: 32457
2012-06-19 10:44:17 +00:00
f509a87f2d
ar71xx: remove superfluous include of asm/mach-ath79/pci.h
...
SVN-Revision: 32455
2012-06-19 10:13:43 +00:00
1a1121158f
ar71xx: add a common function to configure USB power GPIOs
...
SVN-Revision: 32454
2012-06-19 10:13:41 +00:00
27fea0b6d7
ar71xx: correctly detect NETGEAR WNDRMAC
...
This patch helps properly detect a WNDRMAC device. Before this
patch the model is detected as "NETGEAR ?????????N".
Signed-off-by: Roman A. aka BasicXP <x12ozmouse@ya.ru>
SVN-Revision: 32453
2012-06-19 10:13:38 +00:00
ee9bc123fb
ar71xx: add USB LED support by default for WNDR3700/WNDR3800/WNDRMAC
...
This adds kmod-leds-wndr3700-usb package to a default build for
WNDR3700, WNDR3800 and WNDRMAC in order to support the green USB LED.
Signed-off-by: Roman A. aka BasicXP <x12ozmouse@ya.ru>
SVN-Revision: 32452
2012-06-19 10:13:37 +00:00
26cf21df02
ar71xx: add support for the embeddedwireless Dorin board (based on patch by embeddedwireless.de)
...
SVN-Revision: 32447
2012-06-19 00:22:04 +00:00
5d364d0ca1
ar71xx: add support for reading the MAC address from OTP ROM on AR933x
...
SVN-Revision: 32446
2012-06-19 00:21:58 +00:00
dddf321b6e
ar71xx: swap the PHY address of the ethernet port of TL-MR3040/TL-MR11U similar to TL-MR3020 to fix ethernet link detection
...
SVN-Revision: 32336
2012-06-13 12:54:22 +00:00
624505df56
ar71xx: fix LZMA loader build regression from r32090 (thx, juhosg)
...
SVN-Revision: 32095
2012-06-06 19:37:49 +00:00
73b8805e78
ar71xx: fix PHY setup on TL-MR3020 ( fixes #11572 )
...
SVN-Revision: 32093
2012-06-06 17:24:12 +00:00
dc9675282e
ar71xx: add a helper function for setting up PHY4 swapping on ar933x
...
SVN-Revision: 32092
2012-06-06 17:24:09 +00:00
02ab0d3ef9
ar71xx: only build all loader images if the image builder is enabled - saves some time on make target/install
...
SVN-Revision: 32090
2012-06-06 17:24:01 +00:00
a4d96aae8d
bump to 3.3.8
...
SVN-Revision: 32055
2012-06-05 06:57:51 +00:00
7f00e5ffc6
uboot-envtools: update to 2012.04.01
...
SVN-Revision: 32051
2012-06-04 21:55:49 +00:00
cd7ab1d30b
ar71xx: add default LED setup for the DB120 board
...
SVN-Revision: 31997
2012-05-29 16:39:23 +00:00
4e40bdc190
ar71xx: use the generic uci-default functions for initial LED setup
...
SVN-Revision: 31992
2012-05-29 16:39:17 +00:00
a9cd8446f3
ar71xx: do not override the mdio clock for ar9330. the override value (obtained from an atheros driver) seems to break ethernet functionality
...
SVN-Revision: 31956
2012-05-28 20:39:50 +00:00
367e4b3994
ar71xx: improve rx performance of the ethernet driver by using build_skb to deliver a cache-hot skb to the network stack
...
SVN-Revision: 31934
2012-05-28 02:55:59 +00:00
8039a1bbb2
ar71xx: fix MII clock settings for various chips, improves ethernet stability on AR934x
...
SVN-Revision: 31925
2012-05-27 21:02:41 +00:00
8865f0923e
ar71xx: fix TL-WR1041 image size
...
SVN-Revision: 31923
2012-05-27 17:21:47 +00:00
2ae5581447
kernel: update linux 3.3 to 3.3.7
...
SVN-Revision: 31848
2012-05-23 21:05:32 +00:00
c57409e79d
ar71xx: fix an insignificant typo
...
Patch from #11485 .
SVN-Revision: 31847
2012-05-23 21:05:30 +00:00
013f434f5b
ar71xx: fix WLAN led for RB751U-2HnD and RB751G-2HnD
...
Patch by Kamil Trzciński <ayufan@osk-net.pl>
SVN-Revision: 31846
2012-05-23 21:05:25 +00:00
758f670376
ar71xx: add support for TP-Link TL-MR3040
...
Support for TP-Link TL-MR3040. Power LED not working - always on red, after
start should be green.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 31845
2012-05-23 21:05:24 +00:00
39994008cb
linux: move certain disabled symbols to the generic configs
...
* CONFIG_ARCH_DMA_ADDR_T_64BIT
* CONFIG_ARCH_HAS_ILOG2_U32
* CONFIG_ARCH_HAS_ILOG2_U64
* CONFIG_ARCH_PHYS_ADDR_T_64BIT
* CONFIG_ARCH_SUPPORTS_MSI
* CONFIG_GENERIC_CPU_DEVICES
* CONFIG_HWMON_DEBUG_CHIP
* CONFIG_I2C_PXA_PCI
* CONFIG_LEDS_GPIO
* CONFIG_MINIX_FS_NATIVE_ENDIAN
* CONFIG_MLX4_CORE
* CONFIG_POWER_SUPPLY
* CONFIG_POWER_SUPPLY_DEBUG
* CONFIG_QUOTACTL
* CONFIG_SDIO_UART
* CONFIG_SENSORS_K10TEMP
* CONFIG_SENSORS_SCH56XX_COMMON
* CONFIG_SENSORS_VIA_CPUTEMP
* CONFIG_SERIO_AMBAKMI
* CONFIG_SERIO_I8042
* CONFIG_SERIO_LIBPS2
* CONFIG_SERIO_PCIPS2
* CONFIG_SERIO_RAW
* CONFIG_SERIO_SERPORT
* CONFIG_SPI_BITBANG
* CONFIG_SPI_GPIO
SVN-Revision: 31737
2012-05-15 10:58:52 +00:00
a3f2fd187b
ar71xx: remove AG71XX_RX_PKT_RESERVE, it is no longer necessary (found by Eric Dumazet)
...
SVN-Revision: 31736
2012-05-15 10:36:39 +00:00
b472e5d12e
kernel: update linux 3.3 to 3.3.6
...
SVN-Revision: 31709
2012-05-14 09:18:32 +00:00
93c9980b94
ar71xx: fix build error if PCI is disabled
...
SVN-Revision: 31646
2012-05-07 21:16:22 +00:00
34018a630f
kernel: update linux 3.3 to 3.3.5
...
SVN-Revision: 31645
2012-05-07 20:11:43 +00:00
0ff3c396d3
kernel: rewrite the phy packet hook, put it in the network stack to avoid having to keep non-upstream ethernet driver changes
...
SVN-Revision: 31637
2012-05-06 21:19:14 +00:00
9486904079
ar71xx: add profile and build image for the TL-WR1041N v2 board
...
Patch-by: Vince Huang <axishero@foxmail.com>
SVN-Revision: 31610
2012-05-05 17:02:41 +00:00
ab897ab04e
ar71xx: add support for the TP-Link TL-WR1041N v2 board
...
Patch-by: Vince Huang <axishero@foxmail.com>
SVN-Revision: 31608
2012-05-05 17:02:35 +00:00
56f2e08537
ar71xx: update 3.3 patches
...
SVN-Revision: 31602
2012-05-05 13:56:35 +00:00
8fffc6d6df
ar71xx: fix a typo in the db120 mach file
...
Reported-by: Sven Eckelmann <sven@narfation.org>
SVN-Revision: 31601
2012-05-05 13:56:30 +00:00
cbfce53831
kernel: update linux 3.3 to 3.3.4
...
SVN-Revision: 31541
2012-04-30 08:38:11 +00:00
3e3a4d3d6b
ar71xx: allow to disable link polling on unused PHYs
...
SVN-Revision: 31533
2012-04-29 18:29:24 +00:00
a447f1810c
ar71xx: enable MIB counters in the built-in switch of the AR934x
...
SVN-Revision: 31476
2012-04-25 13:02:11 +00:00
59b0c1b2b9
ar71xx: TL-WR741NDv4: add WLAN LED config
...
On TP-Link TL-WR741ND version 4, the WLAN LED must be configured to work.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 31461
2012-04-24 11:38:44 +00:00
8fd383ae2e
kernel: update linux 3.3 to 3.3.3
...
SVN-Revision: 31460
2012-04-24 09:25:38 +00:00
9140d4ee44
ar71xx: remove duplicated AP121 Kconfig entry
...
SVN-Revision: 31382
2012-04-20 16:50:16 +00:00
da2cc2c79a
ar71xx: nuke 3.2 support
...
SVN-Revision: 31360
2012-04-19 21:32:05 +00:00
9854d6fb7f
ar71xx: switch to 3.3.2
...
SVN-Revision: 31359
2012-04-19 21:31:58 +00:00
a6b4b5fd6e
ar71xx: sync 3.3 config
...
SVN-Revision: 31358
2012-04-19 21:31:53 +00:00
ef97415b92
ar71xx: merge/reorganize 3.3 patches
...
SVN-Revision: 31357
2012-04-19 21:31:50 +00:00
408de85883
ar71xx: use ap91_pci_init for RB751{,G}
...
SVN-Revision: 31356
2012-04-19 21:31:48 +00:00
0a9832b50d
ar71xx: move USB device registration directly into rb751{,g}_setup
...
SVN-Revision: 31355
2012-04-19 21:31:43 +00:00
78967e6640
ar71xx: add ap9x_pci_get_wmac_data helper
...
SVN-Revision: 31354
2012-04-19 21:31:42 +00:00
5c9ca38e47
ar71xx: add sanity checks to decode_rle
...
Also use -EINVAL instead of -1.
SVN-Revision: 31353
2012-04-19 21:31:40 +00:00
a8f2bc682e
kernel: also update the targets to use 3.2.15
...
Thanks Gabor for spotting it.
SVN-Revision: 31337
2012-04-17 13:12:14 +00:00
3a9b6dc313
kernel: update linux 3.3 to 3.3.2
...
SVN-Revision: 31336
2012-04-17 12:51:02 +00:00
16b4cbcdd6
kernel: update linux 3.2 to 3.2.14
...
SVN-Revision: 31222
2012-04-09 14:48:51 +00:00
f14fd53e3c
ar71xx: image: build initramfs images for the WHR boards
...
SVN-Revision: 31209
2012-04-06 06:45:08 +00:00
e295a077ce
ar71xx: initial support for Mikrotik RB751G-2HnD and RB751U-2HnD
...
Great collaboration on these two fantastic routers on the openwrt forum:
https://forum.openwrt.org/viewtopic.php?id=32320
Above all kudos to aryufan. Well done and thank you everyone else who
contributed.
To-Do: LED for wlan is not yet activated
To-Do: TxPower over 20dBm (RB751U) or 22dBm (RB751G) are not accepted by
the router
Signed-off-by: Hanno Schupp <hanno.schupp@gmail.com>
[juhosg: fix line wrapped patch, fix checkpatch errors, add missing
kernel patches]
SVN-Revision: 31208
2012-04-06 06:45:07 +00:00
fe6d66afe2
ar71xx: add rb750 to diag.sh
...
Support status led in diag.sh for RB750
Patch from: Evangelos Arkalis <arkalis.e@gmail.com>
SVN-Revision: 31207
2012-04-06 06:45:04 +00:00
d87efd8c3c
kernel: update linux 3.2 to 3.2.13 and refresh patches
...
Also remove a duplicate patch from lantiq (already in generic).
SVN-Revision: 31158
2012-04-01 07:56:55 +00:00
b77217d963
ar71xx: boost SPI flash read performance
...
mtd_speedtest results:
page read speed
old new delta
DB120 929 KiB/s 2597 KiB/s +179.55%
TL-WR1043ND v1 754 KiB/s 2166 KiB/s +187.27%
TL-WR703N v1 745 KiB/s 2176 KiB/s +192.08%
TL-MR3220 v1 752 KiB/s 2154 KiB/s +186.44%
TL-WR2543ND v1 564 KiB/s 2130 KiB/s +277.66%
TL-WR741ND v2 525 KiB/s 1767 KiB/s +236.57%
ALFA-AP96 702 KiB/s 1977 KiB/s +181.62%
WNDR3700 697 KiB/s 1965 KiB/s +181.92%
SVN-Revision: 31118
2012-03-27 19:38:17 +00:00
102c6df148
ar71xx: improve SPI flash read/write performance
...
mtd_speedtest results:
page write speed
old new delta
DB120 209 KiB/s 226 KiB/s +8.13%
TL-WR1043ND v1 122 KiB/s 148 KiB/s +21.31%
TL-WR703N v1 153 KiB/s 194 KiB/s +26.80%
TL-MR3220 v1 130 KiB/s 156 KiB/s +20.00%
TL-WR2543ND v1 158 KiB/s 202 KiB/s +27.85%
TL-WR741ND v2 122 KiB/s 152 KiB/s +24.59%
ALFA AP96 229 KiB/s 260 KiB/s +13.54%
WNDR3700 202 KiB/s 223 KiB/s +10.40%
page read speed
old new delta
DB120 691 KiB/s 929 KiB/s +34.44%
TL-WR1043ND v1 372 KiB/s 754 KiB/s +102.69%
TL-WR703N v1 375 KiB/s 745 KiB/s +98.67%
TL-MR3220 v1 372 KiB/s 752 KiB/s +102.15%
TL-WR2543ND v1 307 KiB/s 564 KiB/s +83.71%
TL-WR741ND v2 315 KiB/s 525 KiB/s +66.67%
ALFA AP96 515 KiB/s 702 KiB/s +36.31%
WNDR3700 515 KiB/s 697 KiB/s +35.34%
SVN-Revision: 31117
2012-03-27 19:38:15 +00:00
6455178a6a
ar71xx: image: build initramfs images for more boards
...
SVN-Revision: 31116
2012-03-27 19:38:13 +00:00
e2bd975a2a
ar71xx: image: add MkuImage{Gzip,Lzma}/initramfs helpers
...
SVN-Revision: 31115
2012-03-27 19:38:11 +00:00
c7966a12b5
ar71xx: image: pass mtdlayout variables by value
...
SVN-Revision: 31114
2012-03-27 19:38:10 +00:00
692e47f49f
ar71xx: image: use MkuImageGzip in Image/Build/AthGzip/initramfs
...
SVN-Revision: 31113
2012-03-27 19:38:08 +00:00
6cd5fb7001
ar71xx: remove the built-in MTD map of the AP96 board
...
Pass the mtd_layout via the kernel command line instead.
SVN-Revision: 31112
2012-03-27 19:38:07 +00:00
61ee283899
ar71xx: remove the built-in MTD map of the PB92 board
...
Pass the mtd_layout via the kernel command line instead
SVN-Revision: 31111
2012-03-27 19:38:05 +00:00
1094dc1996
ar71xx: remove the built-in MTD map of the Zcomax devices
...
Pass the mtd_layout via the kernel command line instead.
SVN-Revision: 31110
2012-03-27 19:38:04 +00:00
24554ef187
ar71xx: reclaim the 'user_property' partition on WHR-* boards
...
SVN-Revision: 31109
2012-03-27 19:38:02 +00:00
87e4ec687b
ar71xx: remove the built-in MTD maps of several boards
...
We are passing the MTD layout via the kernel command line, so
it makes no sense to duplicate it in mach-* files. The patch
removes the built-in MTD maps of the following boards:
* AP113
* ALFA N2/N5
* DIR-600
* DIR-615
* DIR-825
* TEW-6{3,5}2BRP
* TEW-673GRU
* WHR-G301N
* WHR-HP-GN
* WHR-HP-G300N
SVN-Revision: 31108
2012-03-27 19:38:01 +00:00
e6b685650b
ar71xx: use modules for LED triggers
...
SVN-Revision: 31107
2012-03-27 19:37:59 +00:00
e28cd648b7
ar71xx: disable CONFIG_{I2C,SPI}_GPIO
...
SVN-Revision: 31104
2012-03-27 19:37:53 +00:00
6627f45a87
ar71xx: sync 3.3 config
...
SVN-Revision: 31103
2012-03-27 19:37:52 +00:00
f4d1e3d147
ar71xx: fix button polarity on TL-WR703N and TL-WR741N v4
...
SVN-Revision: 31102
2012-03-27 19:37:51 +00:00
ff5b7ef713
linux: refresh patches against 3.3
...
SVN-Revision: 31047
2012-03-20 15:55:07 +00:00
c8bf90d414
ar71xx: fix IRQ number for the AR7240 OHCI controller
...
SVN-Revision: 31044
2012-03-20 15:02:48 +00:00
c1dc6df8bd
kernel: update linux 3.2 to 3.2.12
...
SVN-Revision: 31028
2012-03-19 18:23:31 +00:00
f86e412389
ar71xx: disable unused file system drivers in the nand subtarget
...
SVN-Revision: 31027
2012-03-19 15:57:07 +00:00
b50cfe077c
ar71xx: sync kernel configs
...
SVN-Revision: 31026
2012-03-19 15:57:06 +00:00
8a2e4b49de
ar71xx: add initial support for RB750GL
...
SVN-Revision: 31025
2012-03-19 15:57:04 +00:00
d19f3dd512
ar71xx: make rb750_latch_change 'static void'
...
SVN-Revision: 31024
2012-03-19 15:57:03 +00:00
5348f46c80
ar71xx: add latch_change field to rb750_led_platform_data
...
SVN-Revision: 31023
2012-03-19 15:57:01 +00:00
8a471efe01
ar71xx: add platform data for the RB750 NAND driver
...
SVN-Revision: 31022
2012-03-19 15:56:59 +00:00
e89df99083
ar71xx: use a different pll value on DB120
...
SVN-Revision: 31018
2012-03-19 11:11:22 +00:00
e9b45ebaba
ar71xx: add AR934x specific interface speed setup for ge0
...
SVN-Revision: 31017
2012-03-19 11:11:20 +00:00
6028889727
ar71xx: remove static MTD maps from AP121/DB120 boards
...
SVN-Revision: 31016
2012-03-19 11:11:19 +00:00
db6e326c56
targets: replace madwifi in profiles with ath5k, madwifi is unmaintained
...
SVN-Revision: 31015
2012-03-19 09:58:13 +00:00
6ac12fbb3c
ar71xx: use AR8327 on the DB120 board
...
SVN-Revision: 31012
2012-03-18 22:06:58 +00:00
f601339e79
ar71xx: add profile and generate image for the JA76PF2 board
...
SVN-Revision: 30958
2012-03-16 18:00:40 +00:00
6036151187
ar71xx: add support for the jjPlus JA76PF2 board
...
SVN-Revision: 30957
2012-03-16 18:00:34 +00:00
a680662391
ar71xx: change LED name prefix on the jjplus boards
...
SVN-Revision: 30956
2012-03-16 18:00:26 +00:00
c00b53f3d0
ar71xx: move micrel PHY driver to the generic linux target
...
SVN-Revision: 30946
2012-03-15 09:25:53 +00:00
ff909edf94
ar71xx: ag71xx: fix ARP frame reception on AR934x switch ports
...
SVN-Revision: 30926
2012-03-13 17:29:38 +00:00
cd6a4cde13
ar71xx: ag71xx: start aneg on switch PHYs after reset
...
SVN-Revision: 30925
2012-03-13 17:29:37 +00:00
7c9534cfd7
ar71xx: ag71xx: poll PHY status of all available switch ports
...
SVN-Revision: 30924
2012-03-13 17:29:36 +00:00
8449eecf5f
ar71xx: ag71xx: allow to use port 5 of the AR934x built-in switch
...
SVN-Revision: 30923
2012-03-13 17:29:34 +00:00
1c5ac02a29
ar71xx: reset the switch on AR934x before ethernet device registration
...
SVN-Revision: 30922
2012-03-13 17:29:33 +00:00
17d3131d3c
ar71xx: fix a typo in ar71xx_regs.h
...
SVN-Revision: 30921
2012-03-13 17:29:31 +00:00
66df117d1b
ar71xx: use a dummy callback for interfaces with fixed speed
...
SVN-Revision: 30913
2012-03-12 20:38:58 +00:00
8b2b37ae58
ar71xx: merge ar934x_bo_ddr_flush patch
...
SVN-Revision: 30912
2012-03-12 20:38:57 +00:00
b0bb0793b9
ar71xx: enable UART function for early_printk/console
...
SVN-Revision: 30909
2012-03-12 17:32:39 +00:00
ccc939ebc0
ar71xx: remove a 3.3 patch, it is already in 3.3-rc7
...
SVN-Revision: 30903
2012-03-12 16:27:57 +00:00
0814e61841
ar71xx: fix Compex WPE72 detection
...
SVN-Revision: 30902
2012-03-12 16:27:56 +00:00
088dd4e879
ar71xx: stop image building if a loader is missing
...
SVN-Revision: 30877
2012-03-11 14:03:28 +00:00
31584880bf
ar71xx: add watchdog driver to the default package list
...
SVN-Revision: 30852
2012-03-08 09:00:17 +00:00
2d89fa7f43
ar71xx: fix WPS button polarity on TL-WR2543N
...
SVN-Revision: 30849
2012-03-07 19:50:53 +00:00
c455a0f7be
ar71xx: ag71xx: fix get_port_link callback
...
SVN-Revision: 30841
2012-03-07 16:32:35 +00:00
5a83b3a5c7
ar71xx: ag71xx: use the generic get_port_link implementation
...
SVN-Revision: 30840
2012-03-07 16:32:34 +00:00
86d852927e
ar71xx: refresh patches against 3.3-rc5
...
SVN-Revision: 30801
2012-03-03 14:10:29 +00:00
7052847972
ar71xx: ag71xx: keep VLAN tags if VLAN is not enabled
...
SVN-Revision: 30768
2012-03-01 19:49:05 +00:00
9698a499b6
kernel: update linux 3.2 to 3.2.9
...
SVN-Revision: 30767
2012-03-01 19:49:02 +00:00
6b37484883
ar71xx: use v6.0.0 in UBTN-XM firmwares ( closes #11038 )
...
SVN-Revision: 30712
2012-02-24 20:41:38 +00:00
c918810414
ar71xx: switch to kmod-gpio-button-hotplug
...
SVN-Revision: 30660
2012-02-20 10:51:48 +00:00
3d20de331d
ar71xx: fix image signature for UBNT-XM boards
...
SVN-Revision: 30626
2012-02-18 14:45:52 +00:00
3004f30f01
ar71xx: remove duplicated define from the D-Link profile
...
SVN-Revision: 30577
2012-02-16 09:03:27 +00:00
1bb8a7613e
Add Ubiquiti UniFi Profile; It's an AP without USB so don't include USB drivers by default
...
SVN-Revision: 30571
2012-02-16 07:45:28 +00:00
b797f72319
d-link: Add DIR-601 Profile Definition; It needs different factory images than DIR-600
...
SVN-Revision: 30570
2012-02-16 07:38:33 +00:00
c736e2d4b0
Fix partitions for Cameo-based boards; kernel 3.2 is bigger
...
SVN-Revision: 30569
2012-02-16 07:29:26 +00:00
4685a51301
image: For Cameo-based board fix adding mtd layout to kernel commandline)
...
SVN-Revision: 30568
2012-02-16 07:24:45 +00:00
9a0e17857e
ar71xx: add profile and build image for the TP-Link TL-WR842N/ND v1 boards
...
SVN-Revision: 30508
2012-02-13 17:11:58 +00:00
1c57a22aae
ar71xx: add model detection for TL-WR842N/ND
...
SVN-Revision: 30507
2012-02-13 17:11:57 +00:00
3708227f96
ar71xx: zero partition parser data in m25p80
...
Ths fixes parsing of RedBoot partitions.
SVN-Revision: 30427
2012-02-10 20:19:06 +00:00
6c07149c2d
ar71xx: fix platform description
...
SVN-Revision: 30419
2012-02-10 15:27:49 +00:00
766999085a
ar71xx: ag71xx: add BQL support
...
It will be usable only from linux-3.3.
Based on a patch by Dave Taht <dave.taht@bufferbloat.net>
SVN-Revision: 30417
2012-02-10 14:56:47 +00:00
fc069f030b
ar71xx: add dummy DQL helper functions for 3.2
...
SVN-Revision: 30416
2012-02-10 14:56:44 +00:00
32a18a05f8
ar71xx: add preliminary support for 3.3
...
SVN-Revision: 30410
2012-02-10 11:53:56 +00:00
512df38f5c
ar71xx: disable DDR flush for ethernet on AR934x, it is no longer necessary
...
SVN-Revision: 30409
2012-02-10 11:46:37 +00:00
61f48beadd
ar71xx: fix db120 board detection
...
SVN-Revision: 30408
2012-02-10 11:46:31 +00:00
73b9a8bf9b
ar71xx: allow to build ag71xx w/o PCI support enabled
...
SVN-Revision: 30407
2012-02-10 11:46:10 +00:00
fe0c7aac66
ar71xx: merge 3.2 fixes
...
SVN-Revision: 30406
2012-02-10 08:19:33 +00:00
d72bde99cd
ar71xx: merge files-3.2 to files
...
SVN-Revision: 30405
2012-02-10 08:19:31 +00:00
81b7aaefbe
ar71xx: nuke 2.6.39 support
...
SVN-Revision: 30404
2012-02-10 08:19:28 +00:00
650d777f3d
ar71xx: switch to 3.2.5
...
SVN-Revision: 30403
2012-02-10 08:19:27 +00:00
abeab97efc
ar71xx: refresh 3.2 patches
...
SVN-Revision: 30402
2012-02-10 08:19:25 +00:00
f754063159
ar71xx: 3.2: remove stray semicolons from the PCI fixup patch
...
SVN-Revision: 30400
2012-02-09 21:19:57 +00:00
848dedeb8b
ar71xx: fix ar934x usb reset handling on 3.2
...
SVN-Revision: 30399
2012-02-09 20:39:41 +00:00
09c45f50d4
ar71xx: 3.2: get rid of an unused variable in ath79_spi.c
...
SVN-Revision: 30391
2012-02-08 20:47:58 +00:00
c126bed503
ar71xx: 3.2: fix AHB clock name in rb4xx_spi
...
SVN-Revision: 30390
2012-02-08 20:47:56 +00:00
81f15f5026
ar71xx: add profile and build image for the TEW-673GRU board
...
SVN-Revision: 30377
2012-02-08 16:26:27 +00:00
48e85cd47b
ar71xx: add support for the TRENDNet TEW-673GRU board
...
SVN-Revision: 30376
2012-02-08 16:26:25 +00:00
d9ff9c44ee
ar71xx: add usb on the pb92 board
...
SVN-Revision: 30007
2012-02-03 09:44:51 +00:00
41bd6bd282
ar71xx: fix ethernet LEDs on the WHR-{G301N,HP-G300N,HP-GN} boards
...
SVN-Revision: 29978
2012-01-31 20:49:34 +00:00
c315ce403b
ar71xx: merge DIR-600 A1 and DIR-615 E4 support
...
SVN-Revision: 29976
2012-01-31 18:37:29 +00:00
dd47afc197
ar71xx: fix ethernet LEDs on the DIR-600-A1 board
...
SVN-Revision: 29975
2012-01-31 18:37:24 +00:00
8200f0c61a
ar71xx: unify LED names on D-Link boards
...
SVN-Revision: 29974
2012-01-31 18:37:15 +00:00
faeca86e50
ar71xx: support for D-LINK DIR-615 rev. E4
...
This patch adds support for D-LINK DIR-615 E4 board. It's mostly based
on the existing support for DIR-600 A1, with some changes in the leds
configuration.
It's an updated version of the patch that reliably works on my hw for
about a year (it was built from trunk on Jan 2011). When I decided to
update the firmware and checked for the current support for that device,
I also found previously posted patches by Alexey Loukianov that
mentioned some stability issues. I'm not sure where could be the
difference, the patches are very similar except the wmac led pin number
- I was using 1, and those patches used 17.
[juhosg: add 3.2 support]
Signed-off-by: Vadim Girlin <vadimgirlin@gmail.com>
SVN-Revision: 29973
2012-01-31 18:37:09 +00:00
97e4ddd012
ar71xx: add support for TP-Link TL-MR11U
...
Adds support for TL-MR11U, a portable router with very similar
hardware to the TL-WR703N and TL-MR3020, but with an onboard
2000mAh battery.
Tested, working:
All interfaces (Ethernet, 802.11n, USB)
WPS & Reset switches (Power appears to be a hardware slider)
Ethernet, Wifi, 3G LEDs (Power & charging LEDs hardware controlled)
Sysupgrade
[juhosg: fix indentations to use TABs instead of spaces, fix 3.2 patch
breakage]
Signed-off-by: Simon Taylor <simon.taylor.uk@gmail.com>
SVN-Revision: 29972
2012-01-31 18:37:01 +00:00
8766f32b8c
ar71xx: compress kernel binaries in Image/Prepare stage
...
The lzma compressed kernel is used by one of the loaders.
SVN-Revision: 29971
2012-01-31 18:36:54 +00:00
d5d37febb4
ar71xx: use dynamically allocated partitions in wrt160nl_part
...
SVN-Revision: 29970
2012-01-31 18:36:51 +00:00
eeb00634a7
add support for the Atheros AP113 reference board
...
This reference board is equipped with:
- AR7242 SoC
- AR9580 on-board Wi-Fi
- AR8316 switch
SVN-Revision: 29935
2012-01-28 13:19:49 +00:00
405a0f3905
refresh 3.2 patches
...
SVN-Revision: 29934
2012-01-28 13:19:43 +00:00
b9b768b8d3
ar71xx: use 64k block size for WZR-HP-AG300H
...
SVN-Revision: 29917
2012-01-27 10:42:41 +00:00
ac8116739a
ar71xx: fix sysupgrade image building of atheros boards after r29899
...
SVN-Revision: 29916
2012-01-27 07:51:09 +00:00
013fe76b36
ar71xx: create the temporary directory before building initramfs images
...
Thanks to Florian for reporting.
SVN-Revision: 29915
2012-01-26 21:28:34 +00:00
a5538a18d4
ar71xx: create a profile and build images for Compex WPE72
...
[juhosg: remove ath9k from the the profile package list, build WPE72
image with the Default profile as well]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
SVN-Revision: 29914
2012-01-26 17:01:44 +00:00
e1e84badaa
ar71xx: add support for Compex WPE72/WPE72NX
...
This patch adds support for Compex WPE72 bare board and Compex WPE72NX
Indoor Access Point.
[juhosg: add support to 3.2 as well]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
SVN-Revision: 29912
2012-01-26 17:01:41 +00:00
038d4e0d77
ar71xx: TL-MR3020: fix board detection, fix missing mandatory package and modify LED behaviour
...
This patch fixes the board detection of the TL-MR3020.
The LED behaviour has also been modified:
* The WPS LED is the diag LED now.
* A netdev trigger for the LAN LED has been added.
The profile of the TL-MR3020 has been updated because the needed package
"kmod-ledtrig-usbdev" was missing which resulted in a non-working usbdev
trigger for the 3G/USB LED.
[juhosg: the board name changes has been removed, and the kernel files
has been changed instead.]
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
SVN-Revision: 29905
2012-01-25 07:44:45 +00:00
c11ac55b29
ar71xx: TL-MR3020: fix GPIO polarity for button and switch
...
This patch fixes the GPIO polarity for the button and the sliding
switch. The buttons are not active low. "Pressed" and "Released"
events are wrong without the patch.
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
SVN-Revision: 29904
2012-01-25 07:44:43 +00:00
4f3d6c9ae9
ar71xx: use the lzma loader on the Planex boards
...
SVN-Revision: 29900
2012-01-24 20:12:10 +00:00
5fa9768cee
ar71xx: rename Sysupgrade/{KR,RK} to Sysupgrade/{KR,RK}uImage
...
SVN-Revision: 29899
2012-01-24 20:12:08 +00:00
095c236694
ar71xx: fix the AP/Router LED definitons on MZK-W300NH
...
SVN-Revision: 29897
2012-01-24 18:40:38 +00:00
23e1b451dc
ar71xx: preset WLAN LED config on MZK-W300NH
...
SVN-Revision: 29896
2012-01-24 18:40:36 +00:00
23836d5908
ar71xx: remove hardcoded MTD layout from planex files
...
SVN-Revision: 29895
2012-01-24 18:40:34 +00:00
859c915077
ar71xx: pass mtdlayout to Planex boards via command line
...
SVN-Revision: 29894
2012-01-24 18:40:33 +00:00
6ad9bf8d17
ar71xx: remove an unused header file
...
SVN-Revision: 29893
2012-01-24 18:40:31 +00:00
17bb003891
ar71xx: nuke fs_all variable in image/Makefile
...
SVN-Revision: 29880
2012-01-24 09:47:25 +00:00
1fb88e2541
ar71xx: create interim kernel files in a separate dir
...
This reduces the size of the ImageBuilder tarball a lot.
SVN-Revision: 29879
2012-01-24 09:47:23 +00:00
a43e2f508f
ar71xx: prebuild all loaders in Image/Prepare stage
...
SVN-Revision: 29878
2012-01-24 09:47:22 +00:00
44517a3789
ar71xx: 3.2: fix build errors if PCI is not enabled
...
SVN-Revision: 29870
2012-01-23 08:52:21 +00:00
778db0a13d
ar71xx: fix compiler warning if PCI is not enabled
...
SVN-Revision: 29869
2012-01-23 08:52:18 +00:00
af015f956c
ar71xx: add initial support for 3.2
...
Tested on the following boards:
ALFA AP96
TL-MR3220 v1
TL-WR1043ND v1
TL-WR2543ND v1
TL-WR703N v1
TL-WR741ND v1
TL-WR741ND v4
WNDR3700 v1
WZR-HP-G300NH
SVN-Revision: 29868
2012-01-22 22:38:19 +00:00
386cbfe45b
ar71xx: move arch specific files to files-2.6.39
...
SVN-Revision: 29867
2012-01-22 22:38:11 +00:00
7b7427e52c
ar71xx: build ALFA AP96 images with default profile as well
...
SVN-Revision: 29866
2012-01-22 22:33:15 +00:00
e7dee3aeed
ar71xx: wrt160nl_part: include module.h and fix compiler warnings
...
SVN-Revision: 29856
2012-01-22 17:55:38 +00:00
a7d344565b
ar71xx: tplinkpart: include module.h
...
SVN-Revision: 29855
2012-01-22 17:55:36 +00:00
6c2638c5e2
ar71xx: rename vsc7385 spi driver
...
SVN-Revision: 29853
2012-01-22 13:51:57 +00:00
bb16739db9
ar71xx: rename ap81 spi driver
...
SVN-Revision: 29852
2012-01-22 13:51:56 +00:00
5ef8b922fa
ar71xx: rename rb4xx spi drivers
...
SVN-Revision: 29851
2012-01-22 13:51:54 +00:00
aad175d5b6
ar71xx: rename the nxp_74hc153 driver
...
SVN-Revision: 29850
2012-01-22 13:51:52 +00:00
ef1c53b7b7
ar71xx: change board id of the UniFi board
...
SVN-Revision: 29849
2012-01-22 13:51:50 +00:00
f90e578903
ar71xx: include linux/module.h in the micrel phy driver
...
SVN-Revision: 29848
2012-01-22 13:51:49 +00:00
fbf81c8e79
ar71xx: move irq_to_gpio and gpio_to_irq into gpio.c
...
SVN-Revision: 29713
2012-01-11 18:00:50 +00:00
67f62cf5cf
ar71xx: disable ath79 in order to get rid of Kconfig warnings
...
SVN-Revision: 29711
2012-01-11 09:14:19 +00:00
88d8cdd503
ar71xx: pb44_spi: add shutdown handler
...
This allows to access the flash from a kexec'd kernel.
SVN-Revision: 29710
2012-01-11 09:14:18 +00:00
e1b7995aef
ar71xx: pb44_spi: call pb44_spi_{en,dis}able from probe/remove
...
SVN-Revision: 29709
2012-01-11 09:14:17 +00:00
67444c7795
ar71xx: pb44_spi: introduce pb44_spi_{en,dis}able helpers
...
SVN-Revision: 29708
2012-01-11 09:14:15 +00:00
0f566a376c
ar71xx: ar71xx_spi: add shutdown handler
...
This allows to access the flash from a kexec'd kernel.
SVN-Revision: 29707
2012-01-11 09:14:14 +00:00
09a6e3f662
ar71xx: ar71xx_spi: save and restore regs from probe/remove
...
SVN-Revision: 29706
2012-01-11 09:14:13 +00:00
714a9bd641
ar71xx: ar71xx_wdt: add shutdown handler
...
SVN-Revision: 29705
2012-01-11 09:14:11 +00:00
9727256330
ar71xx: refresh patches
...
SVN-Revision: 29683
2012-01-07 19:36:43 +00:00
4edff7d3ef
ar71xx: add a profile and build images for the TL-WR2543N/ND
...
SVN-Revision: 29682
2012-01-07 19:36:42 +00:00
a1dcbc66a6
ar71xx: add initial support for the TL-WR2543N/ND board
...
The WLAN LEDs are not working yet.
SVN-Revision: 29680
2012-01-07 19:36:35 +00:00
a56bdeff9d
ar71xx: allow to specify max read size for m25p80
...
Reading from the flash chip on the TL-WR2543ND seems buggy.
If the SPI flash driver tries to read too much data in one
SPI transfer, the flash chip returns bogus values. This can
be caused by a buggy flash chip on my board, or it can
be a bug in our SPI driver.
Add a workaround to the m25p80 driver until I find out the
root cause of the problem. The patch allows to specify the
maximum numner of bytes which can be read safely withint
one SPI transfer.
SVN-Revision: 29679
2012-01-07 19:36:33 +00:00
67b2814842
ar71xx: local mac support on the wndr3700
...
The wndr3700 at least has no eth0 mac address and usually leverages
the first wireless device's mac when in a bridged scenario. If,
however, you want to route, and not bridge the interfaces, you
need a unique mac address for it.
This patch sets the local bit on the mac address pulled from the
wireless chip and uses the resulting address for eth0.
Patch-by: Dave Taht <dave.taht@gmail.com>
SVN-Revision: 29675
2012-01-07 17:24:44 +00:00
6c74274c8d
generic: improve MIPS kexec support
...
It is based on patches from the linux-longsoon-community git tree:
http://dev.lemote.com/cgit/linux-loongson-community.git/
Now the kernel can use the command line parameter from kexec-tools.
Runtime tested on ar71xx with 2.6.39.4 (the wathdog must be stopped
before executing the new kernel). Compile tested with lantiq (3.1.4)
and brcm47xx (3.0.12).
SVN-Revision: 29674
2012-01-07 16:29:16 +00:00
f638c6207b
ar71xx: fix sysupgrade on the TL-WR841N/ND v7 boards
...
SVN-Revision: 29672
2012-01-06 15:54:59 +00:00
1e848b17ad
ar71xx: add support for Redwave RW2458N
...
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 29669
2012-01-06 07:20:59 +00:00
84cd8a5ee0
ar71xx: fix RB-750 network configuration
...
SVN-Revision: 29668
2012-01-06 07:20:54 +00:00
8eb0b7ab3d
ar71xx: fix sections mismatch warnings in the nand drivers
...
SVN-Revision: 29667
2012-01-05 18:08:33 +00:00
232eb83f74
ar71xx: fix LED configuration on the RB-750
...
SVN-Revision: 29666
2012-01-05 18:08:28 +00:00
d65c6fe720
ar71xx: create profile and build image for the ALFA AP96 board
...
SVN-Revision: 29663
2012-01-04 21:13:57 +00:00
b8f0d86115
ar71xx: add inital support for the ALFA Network AP96 board
...
The microSD slot and the Real Time Clock is not working yet.
The miniPCIe interface is not tested due to the lack of a
suitable card.
SVN-Revision: 29662
2012-01-04 21:13:54 +00:00
807e046193
ar71xx: specify console kernel parameter for the Compex boards
...
SVN-Revision: 29660
2012-01-04 17:30:59 +00:00
923f3e3752
ar71xx: allow to use the command line hack on compex devices
...
SVN-Revision: 29659
2012-01-04 17:30:58 +00:00
2f53f82203
ar71xx: use the TL-MR3x20 code for the TL-WR841N/ND v7
...
These models are based on the AP99 reference board,
and uses the AR7241 SoC.
SVN-Revision: 29658
2012-01-04 17:30:57 +00:00
301b1b4f92
ar71xx: show correct model name on TL-WA701N/ND boards
...
SVN-Revision: 29657
2012-01-04 17:30:55 +00:00
ac68f0d8fa
ar71xx: add profile and build image for the TL-WA701N/ND boards
...
SVN-Revision: 29656
2012-01-04 17:30:54 +00:00
72019009c7
ar71xx: fix network configuration for the TL-WA901N/ND boards
...
SVN-Revision: 29654
2012-01-04 17:30:52 +00:00
90bfef9ec9
ar71xx: allow to use LAN LED on the TL-WA901N/ND boards
...
SVN-Revision: 29653
2012-01-04 17:30:50 +00:00
5eb502d9c1
ar71xx: add default LED configuration for the TL-MR3020
...
Also use the system LED for diagnostic.
SVN-Revision: 29652
2012-01-04 17:30:49 +00:00
1045c83527
ar71xx: add support for TP-Link TL-MR3020
...
This patch adds support for the TP-Link device TL-MR3020 which is very
similiar to the TL-WR703N.
The TL-MR3020 uses 5 LEDs, 1 push button and a switch with 3 positions.
Only four LEDs can be controlled via GPIO. The power LED is connected to
the power supply.
The WPS push button has been mapped to KEY_WPS_BUTTON. The two GPIO signals
of the sliding switch have been mapped to BTN_0 and BTN_1.
I have also setup a wiki page with details here:
http://wiki.openwrt.org/toh/tp-link/tl-mr3020
USB is working and has been tested with USB mass storage and USB UMTS
stick.
Wifi also seems to work.
Ethernet is working too.
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
SVN-Revision: 29651
2012-01-04 17:30:47 +00:00
88223f87d1
ar71xx: use the new om-watchdog package for OM2P
...
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
SVN-Revision: 29648
2012-01-04 17:30:41 +00:00
8854c90119
ar71xx: add profile and build factory image for the Hornet-UB board
...
SVN-Revision: 29637
2012-01-01 19:30:29 +00:00
1d3de89f3c
ar71xx: build images for the ALFA Network N2/N5 boards
...
SVN-Revision: 29636
2012-01-01 19:30:28 +00:00
1e68f10b87
ar71xx: add support for the ALFA Network N2/N5 boards
...
SVN-Revision: 29635
2012-01-01 19:30:25 +00:00
5c067db8a7
ar71xx: define LAN/WAN LEDs for the TL-WR741N/ND boards
...
SVN-Revision: 29631
2011-12-31 15:02:46 +00:00
fff02e6ea8
ar71xx: enable SWCONFIG_LEDS
...
SVN-Revision: 29630
2011-12-31 15:02:40 +00:00
8c2482f76e
ar71xx: ag71xx: implement get_port_{link,stats} callbacks
...
SVN-Revision: 29626
2011-12-31 15:02:26 +00:00
557009bbdb
ar71xx: fix LEDs on the WRT400N
...
SVN-Revision: 29624
2011-12-31 13:54:11 +00:00
76dacee995
ar71xx: enable sysupgrade support for airrouter
...
Works for me! ;-)
Patch-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 29614
2011-12-27 16:59:43 +00:00
c6ee919b2a
ar71xx: fix sysupgrade on PB42/PB44 boards
...
SVN-Revision: 29613
2011-12-27 16:57:01 +00:00
db0a1db257
ar71xx: set a reserved bit that resets to 1 when writing the address table control register on the ar7240 switch (should fix #10547 )
...
SVN-Revision: 29598
2011-12-22 05:43:53 +00:00
8799627ef0
ar71xx: add default network config for buffalo WZR-HP-G300NH2 and WZR-HP-G450H
...
Thanks netprince for reporting and testing.
SVN-Revision: 29595
2011-12-21 19:32:40 +00:00
ebefe1eb3a
the mach file of the WZR-HP-G300NH2 accidentally claimed the mach id of the WZR-HP-AG300H, correct the id ( #10649 )
...
SVN-Revision: 29593
2011-12-21 01:27:48 +00:00
11013ad947
ar71xx: add missing wireless led changes for wzr-hp-g300nh2
...
SVN-Revision: 29568
2011-12-19 09:04:15 +00:00
0cc056cb7e
ar71xx: add support for the wzr-hp-g300nh2
...
Signed-off-by: Mark Deneen <mdeneen@gmail.com>
SVN-Revision: 29567
2011-12-18 22:20:17 +00:00
5a0a2b2f1b
ar71xx: use 64kraw template on more TP-Link boards
...
SVN-Revision: 29561
2011-12-17 18:49:55 +00:00
67c7980290
ar71xx: connect GMAC0 to the internal switch on DB120
...
Because the external switch has no driver yet, connect GMAC0
to the PHY4 of the internal switch for now. This allows to
use the DB120 board as a router with 4LAN+1WAN ports.
SVN-Revision: 29557
2011-12-15 22:25:38 +00:00
5bbd416e38
ar71xx: add defines for the AR934X GMAC interface
...
SVN-Revision: 29556
2011-12-15 22:25:36 +00:00
e47a8c2bb2
ar71xx: fix GMAC1 interface speed on the DB120 board
...
SVN-Revision: 29555
2011-12-15 22:25:35 +00:00
36bc2c2c80
ar71xx: ag71xx: fix switch port setup for AR934X
...
SVN-Revision: 29554
2011-12-15 22:25:32 +00:00
00667c3846
ar71xx: ag71xx: allow to connect PHY4 to the CPU on AR934X
...
SVN-Revision: 29553
2011-12-15 22:25:30 +00:00
0540970345
ar71xx: ag71xx: setup switch interface mode on AR934X
...
SVN-Revision: 29552
2011-12-15 22:25:29 +00:00
44014110b8
ar71xx: ag71xx: detect the built-in switch of the AR934X SoCs
...
SVN-Revision: 29551
2011-12-15 22:25:28 +00:00
e2a546d475
ar71xx: allow to attach the internal switch for AR934x
...
SVN-Revision: 29550
2011-12-15 22:25:22 +00:00
9ae65588d8
ar71xx: introduce ar71xx_switch_data
...
SVN-Revision: 29549
2011-12-15 22:25:11 +00:00
bfe747b7d9
ar71xx: build images for TL-WR741N/ND v2
...
SVN-Revision: 29548
2011-12-15 22:03:48 +00:00
aefff26624
ar71x: use raw squashfs images for TP-Link boards
...
SVN-Revision: 29547
2011-12-15 22:03:46 +00:00
d5bd28ffae
ar71xx: create a template for using unpadded squashfs images
...
SVN-Revision: 29546
2011-12-15 22:03:45 +00:00
dbc4fa4b5b
ar71xx: put squash image right after the kernel on TP-Link boards
...
SVN-Revision: 29545
2011-12-15 22:03:44 +00:00
850be54b72
ar71xx: tplinkpart: allow to detect JFFS2 as well
...
SVN-Revision: 29543
2011-12-15 22:03:40 +00:00
b7d7481b07
ar71xx: ag71xx: check PHY IDs before accessing the switch registers
...
SVN-Revision: 29541
2011-12-15 13:25:23 +00:00
0655552860
ar71xx: ag71xx: don't use port 4 of the switch, it is not connected on ar724x
...
SVN-Revision: 29540
2011-12-15 13:25:21 +00:00
204fc6bed5
ar71xx: ag71xx: nuke ar7240sw_init
...
SVN-Revision: 29539
2011-12-15 13:25:20 +00:00
d1f7783612
ar71xx: fix mac addresses on jjPlus devices
...
SVN-Revision: 29538
2011-12-15 13:25:18 +00:00
d3058b8f8c
ar71xx: build image for the Hornet-UB board
...
SVN-Revision: 29536
2011-12-14 20:54:11 +00:00
b9c5cb5c9a
ar71xx: add support for ALFA Network's Hornet-UB board
...
SVN-Revision: 29535
2011-12-14 20:54:10 +00:00
66c8cc0f6d
ar71xx: add GPIO function bit defines for AR933X
...
SVN-Revision: 29534
2011-12-14 20:54:07 +00:00
7076d74b21
ar71xx: fix gpio count for ar7241/ar7242
...
SVN-Revision: 29532
2011-12-14 20:47:24 +00:00
b878f4a927
ar71xx: register extra leds behind the wireless mac on wzr-hp-g450h
...
SVN-Revision: 29531
2011-12-14 20:21:42 +00:00
d2717d3d47
ar71xx: get rid of squashfs-4k images
...
SVN-Revision: 29522
2011-12-13 20:41:24 +00:00
4a441570ca
kernel: move linux/ath9k_platform.h to generic files so that it can be reused from other targets
...
SVN-Revision: 29516
2011-12-13 15:14:59 +00:00
3806671fe5
ar71xx: fix wireless led on wzr-hp-g450h
...
SVN-Revision: 29515
2011-12-13 15:00:43 +00:00
2dd7dfb1c9
ar71xx: enable AR9341 support at setup.c
...
Patch-by: dyq <729650915@qq.com>
SVN-Revision: 29514
2011-12-13 14:59:43 +00:00
058998acdb
ar71xx: Build images for Netgear WNDRMAC and WNDRMACv2
...
The WNDRMAC is a WNDR3700v2 (64MB RAM, 16MB flash) in a white case. The
WNDRMACv2 is a WNDR3800 (128MB RAM, 16MB flash) in a WNDRMAC case.
The WNDRMAC case doesn't have "holes" or labels for the 2.4GHz LED or
switch ports 2-4. The stock firmware uses a single LED (in the 5GHz
position) to indicate the status of both radios, and a single LED (in the
switch port 1 position) to indicate the status of all LAN ports. The
"missing" LEDs are present on the board, and easily shine through the
case. Unlike the stock firmware, OpenWrt will use these "hidden" LEDs.
I've tested the WNDRMACv2 image. I don't have a v1 WNDRMAC, but assume
that this is sufficient to build a fully-functional image.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 29513
2011-12-13 14:59:40 +00:00
48f9717371
ar71xx: add gpios and usb for wzr-hp-g450h
...
SVN-Revision: 29509
2011-12-13 13:33:44 +00:00
4ca2d86493
ar71xx: use RedBoot parser on PB44
...
SVN-Revision: 29501
2011-12-11 15:52:47 +00:00
6e69765559
ar71xx: fix WNDR3x00 factory image generation
...
Factory images for WNDR3700v2 and WNDR3800 should contain these model IDs
for the device: field in their DNI tags, not WNDR3700.
This regressed in r29434, which redid WNDR3x00 model detection. The sixth
parameter to Image/Build/Netgear is only used as the -B argument to
mkdniimg, which is used to set the device: field. In r29434, this was
erroneously changed to be WNDR3700 for all models. The tools to flash
factory images (U-Boot's TFTP server and the factory software's upgrade
utility) may refuse to honor images with incorrect device: fields in their
DNI tags.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 29473
2011-12-07 06:55:50 +00:00
8eb8a6e1e7
ar71xx: fix WNDR3x00 model detection
...
Detect the model name for /tmp/sysinfo/model based on 10 bytes at offset
56 in the art (caldata) mtd partition.
r29434 redid WNDR3x00 model detection, attempting to distinguish between
WNDR3700v2 and WNDR3800 by checking MemTotal in /proc/meminfo. However, it
contained a bug: it put the awk inside a $(...), with the result that all
WNDR3700v2 and WNDR3800 models would be reported as WNDR3800. This patch
checks the model name stored in the art partition, as is done by U-Boot
shipping on the WNDR3800. It has the likely advantage of working with
future models based on the WNDR3700 board. It also will not mis-detect
units on which people install more memory.
I have tested this patch on WNDR3700 (v1), WNDR3700v2, and WNDR3800.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 29472
2011-12-07 06:55:39 +00:00
c6b2b98812
ar71xx: create firmware image for the TL-WR740N/ND v4 boards
...
Based on a patch by Cristian Deluxe <djcristiandeluxe@gmail.com>
SVN-Revision: 29468
2011-12-06 16:26:44 +00:00
fbfad4e9b4
ar71xx: use hw_id, hw_rev and flash_layout with mktplinkfw
...
SVN-Revision: 29467
2011-12-06 16:26:43 +00:00
d753e08c79
ar71xx: fix TL-MR3x20 profile names in image/Makefile
...
SVN-Revision: 29463
2011-12-06 13:53:21 +00:00
62d8009cdd
ar71xx: cleanup TP-Link profiles
...
SVN-Revision: 29461
2011-12-06 10:29:25 +00:00
f7a482d382
ar71xx: add TP-Link board detection
...
SVN-Revision: 29459
2011-12-05 21:11:01 +00:00
bdc2eca7de
ar71xx: use correct mac on the lan interface on several TP-LINK devices
...
SVN-Revision: 29458
2011-12-05 21:10:58 +00:00
0103069372
ar71xx: allow to pass negative offset values for ar71xx_init_mac
...
SVN-Revision: 29457
2011-12-05 21:10:55 +00:00
ada92aee62
ar71xx: don't register PCI controller on AR934x if PCIE_RC bit is not set
...
SVN-Revision: 29456
2011-12-05 18:21:15 +00:00
c6bcf8d1d8
ar71xx: verify hardware id of firmware images on TP-Link boards
...
SVN-Revision: 29455
2011-12-05 18:11:51 +00:00
4dc9092f4b
ar71xx: reclaim some unused space on TP-Link boards
...
With the default OpenWrt configuration, this increases the size
of the rootfs_data partition by 384KB/128KB on the older/newer
TP-Link models.
SVN-Revision: 29447
2011-12-05 14:52:36 +00:00
3e7a6d182a
ar71xx: check squashfs signature in TP-Link mtd parser
...
SVN-Revision: 29446
2011-12-05 14:52:33 +00:00
feebf484ba
ar71xx: use the lzma-loader on TP-Link boards w/o lzma support
...
SVN-Revision: 29444
2011-12-05 14:52:28 +00:00
d42968351f
ar71xx: add lzma loader
...
SVN-Revision: 29443
2011-12-05 14:52:25 +00:00
1f809532de
ar71xx: add preliminary support for wzr-hp-g450h
...
SVN-Revision: 29441
2011-12-05 14:20:51 +00:00
d1f63f8538
ar71xx: move multi-m25p80 concat code from wzr-hp-ag300h mach code to dev-m25p80.c, other buffalo routers use it as well
...
SVN-Revision: 29440
2011-12-05 14:20:44 +00:00
4cc2b9bb06
ar71xx: rewrite WNDR3700/3800 handling
...
SVN-Revision: 29434
2011-12-05 13:03:54 +00:00
78699c2e51
add some missing wndr3800 base-files definitions
...
SVN-Revision: 29433
2011-12-05 12:56:21 +00:00
5177814ade
ar71xx: change user-space board detection
...
SVN-Revision: 29432
2011-12-05 12:56:20 +00:00
8a3a60fc64
ar71xx: allow WNDR3700 image creation to fail if kernel/rootfs too big
...
SVN-Revision: 29431
2011-12-05 12:47:53 +00:00
7cfa39f032
ar71xx: use the tp-link parser on the tp-link boards
...
Also remove static partition maps.
SVN-Revision: 29416
2011-12-03 18:13:31 +00:00
514b1167c9
ar71xx: add mtd partition parser for the TP-Link boards
...
SVN-Revision: 29415
2011-12-03 18:13:27 +00:00
fc7fb29bae
ar71xx: run the RedBoot parser only on the RedBoot based boards
...
SVN-Revision: 29414
2011-12-03 18:13:25 +00:00
9cc28d5aa0
ar71xx: run the MyLoader parser only on the WP543 board
...
SVN-Revision: 29413
2011-12-03 18:13:23 +00:00
67a0b9aada
ar71xx: run the wrt160nl parser only on the WRT160NL board
...
Also remove static mtd partition definitions.
SVN-Revision: 29412
2011-12-03 18:13:20 +00:00
c8acd6e013
ar71xx: allow to pass part_probe types to the m25p80 driver
...
SVN-Revision: 29411
2011-12-03 18:13:18 +00:00
20483faed0
ar71xx: create initramfs images for the newer TP-Link boards
...
SVN-Revision: 29410
2011-12-03 16:57:23 +00:00
9a2005e5e6
ar71xx: remove swconfig and wpad-mini from custom profiles
...
SVN-Revision: 29408
2011-12-03 16:33:41 +00:00
bc1d818610
ar71xx: add uboot-envtools to the default package list
...
SVN-Revision: 29407
2011-12-03 16:33:40 +00:00
a02a9c3f8b
ar71xx: reclaim unused space in WNDR3700/3800 images
...
Patch by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 29406
2011-12-03 16:33:38 +00:00
ac82296c53
ar71xx: add a profile and build image for the OM2P board
...
[juhosg: the name of the final image has been changed to
'openwrt-ar71xx-generic-om2p-squashfs-factory.bin']
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
SVN-Revision: 29397
2011-12-01 22:49:05 +00:00
f188f1bad5
ar71xx: add support for Ubiquiti AirRouter
...
Signed-off-by: Gergely Barta <gergely.barta@printerfairkft.hu>
SVN-Revision: 29395
2011-12-01 22:49:02 +00:00
0612667c34
ar71xx: configure default led behavior for the OM2P
...
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
SVN-Revision: 29394
2011-12-01 22:48:59 +00:00
39348e387f
ar71xx: use /lib/functions/uci-defaults.sh
...
SVN-Revision: 29385
2011-12-01 22:48:47 +00:00
f20797306a
ar71xx: modify phy mask of the WP543 board
...
This fixes ethernet on newer boards. Based on a patch from #9702 .
SVN-Revision: 29328
2011-11-24 20:09:43 +00:00
c20d7378e5
ar71xx: fix wndr3800 machine name
...
This fixes the machine name in /proc/cpuinfo and luci status page machine name.
Signed-off-by: Petri Rosenström <petri.rosenstrom@gmail.com>
SVN-Revision: 29326
2011-11-24 20:09:38 +00:00
600b6efc41
ar71xx: copy atheros initramfs images to the image directory
...
SVN-Revision: 29325
2011-11-24 20:09:35 +00:00
d97cf76790
ar71xx: specify mtd layout in command line for the DB120 board
...
SVN-Revision: 29324
2011-11-24 20:09:32 +00:00
9990523a0f
ar71xx: set GE0 phy_mask for AR933x
...
SVN-Revision: 29274
2011-11-20 11:30:10 +00:00
f27548448b
ar71xx: fix USB LED on the DB120 board
...
SVN-Revision: 29126
2011-11-14 17:43:15 +00:00
6ebbb1329d
ar71xx: add a function for selecting output signal on a given GPIO pin
...
SVN-Revision: 29125
2011-11-14 17:43:14 +00:00
0c1d3617d7
ar71xx: fix GPIO function handling on AR934x
...
SVN-Revision: 29124
2011-11-14 17:43:13 +00:00
aa0c8c4885
ar71xx: add AR71XX_ prefix to GPIO_REG_* defines
...
SVN-Revision: 29123
2011-11-14 17:43:11 +00:00
62a7795afd
ar71xx: merge nand scan patch
...
SVN-Revision: 29122
2011-11-14 17:43:10 +00:00
Gabor Juhos
Felix Fietkau
John Crispin
Luka Perkov
Jonas Gorski
Daniel Dickinson
Florian Fainelli
Jo-Philipp Wich