Add support for RS485 tranceiver with transmit/receive switch hooked
to a RTS GPIO pin.
Use the 'rts-gpios' and 'rs485-rts-active-low' properties as described
in devicetree/bindings/serial/rs485.yaml.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds support for the various clones of the TL-WA830RE recently
supported in fb99ac6807 ("ath79: add support for TP-Link TL-WA830RE v1"):
- tplink,tl-wa701nd-v1
- tplink,tl-wa730re-v1
- tplink,tl-wa801nd-v1
- tplink,tl-wa830re-v1 (already supported)
- tplink,tl-wa901nd-v1
Since these devices are 100%-clones in ar71xx, this patch adds all
of them without run-testing (as this has been done for TL-WA830RE v1).
Specifications:
- SOC: Atheros AR7240
- CPU: 400MHz
- Flash: 4 MiB (Spansion S25FL032P)
- RAM: 32 MiB (Zentel A3S56D40FTP-G5)
- WLAN: Atheros AR9280 bgn 2x2
- Ethernet: 1 port (100M)
Flash instructions:
- install from u-boot with tftp (requires serial access)
> setenv ipaddr a.b.c.d
> setenv serverip e.f.g.h
> tftpboot 0x80000000 \
openwrt-ath79-tiny-tplink_tl-waxxxxx-v1-squashfs-factory.bin
> erase 0x9f020000 +0x3c0000
> cp.b 0x80000000 0x9f020000 0x3c0000
> bootm 0x9f020000
- flash factory image from OEM WebUI
- sysupgrade from ar71xx image
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
With the wrong blocksize, the rootfs was not positioned on the boundary
of a block, thus breaking the mtdsplit driver.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds the label MAC address for the Ubiquiti Picostation M (XM).
This was overlooked when adding support in the previous patch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for the Ubiquiti Picostation M (XM), which has the
same board/LEDs as the Bullet M XM, but different case and antennas.
Specifications:
- AR7241 SoC @ 400 MHz
- 32 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- External antenna: 5 dBi (USA), 2 dBi (EU)
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB
Flashing via WebUI:
Upload the factory image via the stock firmware web UI.
Attention: airOS firmware versions >= 5.6 have a new bootloader with
an incompatible partition table!
Please downgrade to <= 5.5 _before_ flashing OpenWrt!
Refer to the device's Wiki page for further information.
Flashing via TFTP:
Same procedure as other NanoStation M boards.
- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
$ tftp 192.168.1.20
tftp> bin
tftp> trace
tftp> put openwrt-ath79-generic-xxxxx-ubnt_picostation-m-squashfs-factory.bin
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for the Ubiquiti Nanostation Loco M (XM), which
has the same board/LEDs as the Bullet M XM, but different case and
antennas.
Specifications:
- AR7241 SoC @ 400 MHz
- 32 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- NS Loco M2: built-in antenna: 8 dBi; AR9287
- NS Loco M5: built-in antenna: 13 dBi; 2T2R 5 GHz radio
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB
Flashing via WebUI:
Upload the factory image via the stock firmware web UI.
Note that only certain firmware versions accept unsigned
images. Refer to the device's Wiki page for further information.
Flashing via TFTP:
Same procedure as other NanoStation M boards.
- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
$ tftp 192.168.1.20
tftp> bin
tftp> trace
tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-squashfs-factory.bin
Tested on NanoStation Loco M2.
Signed-off-by: Sven Roederer <freifunk@it-solutions.geroedel.de>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Several devices with tplink-safeloader contain default values (0x0)
for TPLINK_HWID and TPLINK_HWREV in their device definitions.
Move those to common tplink-safeloader definition so they do not
have to be repeated each time.
While at it, set default value for tplink-v1 and tplink-v2 as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds a pinmux to the shared DTSI for TP-Link TL-WR841N/ND v8,
TL-WR842N v2 and TL-MR3420 v2. It is supposed to be the equivalent
of:
/* config gpio4 as normal gpio function */
ath79_gpio_output_select(TL_MR3420V2_GPIO_USB_POWER,AR934X_GPIO_OUT_GPIO);
This allows to enable USB power on these devices.
While at it, move the jtag_disable_pins to &gpio node and remove the
redundant status=okay there.
Tested on TP-Link TL-WR842N v2.
Fixes: FS#2753
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Armin Fuerst <armin@fuerst.priv.at>
Mikrotik devices will be found in both generic and nand subtargets.
The file mikrotik-caldata.sh, currently used in generic, contains
a few lines of code that would need to be duplicated for nand
support. Instead of duplicating it, move it to target base-files,
as size impact is small and the maintenance gain should outweigh it.
This is changed separately to make life easier for the people
currently working on Mikrotik NAND support.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hardware
--------
SoC: Atheros AR7161
RAM: Samsung K4H511638D-UCCC
2x 64M DDR1
SPI: Micron M25P128 (16M)
WiFi: Atheros AR9160 bgn
Atheros AR9160 an
ETH: Broadcom BCM5481
LED: Power (Green/Red)
ETH (Green / Blue / Yellow)
(PHY-controlled)
WiFi 5 (Green / Blue)
WiFi 2 (Green / Blue)
BTN: Reset
Serial: Cisco-Style RJ45 - 115200 8N1
Installation
------------
1. Download the OpenWrt initramfs-image. Place it into a TFTP server
root directory and rename it to 1401A8C0.img. Configure the TFTP
server to listen at 192.168.1.66/24.
2. Connect the TFTP server to the access point.
3. Connect to the serial console of the access point. Attach power and
interrupt the boot procedure when prompted (bootdelay is 1 second).
4. Configure the U-Boot environment for booting OpenWrt from Ram and
flash:
$ setenv boot_openwrt 'setenv bootargs; bootm 0xbf080000'
$ setenv ramboot_openwrt 'setenv serverip 192.168.1.66;
tftpboot; bootm'
$ saveenv
5. Load OpenWrt into memory:
$ run ramboot_openwrt
Wait for the image to boot.
6. Transfer the OpenWrt sysupgrade image to the device. Write the image
to flash using sysupgrade:
$ sysupgrade -n /path/to/openwrt-sysuograde.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
The Siemens WS-AP3610 asserts reset to the ethernet PHY with the
reset-register. Backport the necessary patches to de-assert reset
when probing the PHY.
These patches can be dropped when using kernel 5.4.
Signed-off-by: David Bauer <mail@david-bauer.net>
The TL-WR940N v6 is similar to v3/v4, it just has different
LEDs and MAC address assignment.
Specification:
- 750 MHz CPU
- 32 MB of RAM
- 4 MB of FLASH
- 2.4 GHz WiFi
- 4x 10/100 Mbps Ethernet
The use of LEDs is based on ar71xx, so blue LED is used for WAN
and orange LED for diag (boot/failsafe/etc.).
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to
wr940nv6_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Thanks to Manuel Kock for reviewing and testing this patch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Manuel Kock <github.web@manu.li>
This adds the ar71xx board name to the SUPPORTED_DEVICES on ath79,
so forceless sysupgrade on this device becomes possible.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This ports support for the TL-WA830RE v1 range extender from ar71xx to
ath79.
Specifications:
- SOC: Atheros AR7240
- CPU: 400MHz
- Flash: 4 MiB (Spansion S25FL032P)
- RAM: 32 MiB (Zentel A3S56D40FTP-G5)
- WLAN: Atheros AR9280 bgn 2x2
- Ethernet: 1 port (100M)
Flash instructions:
- install from u-boot with tftp (requires serial access)
> setenv ipaddr a.b.c.d
> setenv serverip e.f.g.h
> tftpboot 0x80000000 \
openwrt-ath79-tiny-tplink_tl-wa830re-v1-squashfs-factory.bin
> erase 0x9f020000 +0x3c0000
> cp.b 0x80000000 0x9f020000 0x3c0000
> bootm 0x9f020000
- flash factory image from OEM WebUI
- sysupgrade from ar71xx image
The device seems to be a clone of the following devices not yet
added to ath79:
- tl-wa701nd-v1
- tl-wa730re-v1
- tl-wa801nd-v1
- tl-wa901nd-v1
Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
[make use of ar7240_tplink.dtsi, add note about clones]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The current set of TP-Link devices with ar7240 SoC all share
the same DTSI file. As the latter is very similar to the
definition required for the to-be-supported TP-Link TL-WA devices
with ar7240, this patch splits the definitions into a shared part
for all TP-Link devices (ar7240_tplink.dtsi) and a file containing
the specific setup for the present TL-WR devices
(ar7240_tplink_tl-wr.dtsi), equivalent to the former
ar7240_tplink_tl-wr74xn-v1.dtsi.
While at it, remove unused firmware partition label and rename
pinmux_switch_led_pins.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
If bootloader doesn't terminate its last spi operation properly
before starting kernel, our first transfer in kernel becomes a
continuous transfer to that request instead of a new one.
Fix this flaw by restoring IOC register, which restored all pin
state to default.
Fixes: ebf0d8dade ("ath79: add new ar934x spi driver")
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Inspired by commit c48b571ad7, add an LED trigger for the WAN LED on top of
the TP-Link TL-WR902AC v1. Currently, only the LED on the port itself shows the
link state, while the LED on top of the device stays dark.
The WAN port of the device is a hybrid LAN/WAN one, hence why the LED at the
port was labeled LAN.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
AR934x chips also got the 'old' qca,ar9330-uart in addition to the
'new' ns16550a compatible one. Add support for UART1 clock selector as
well as device-tree bindings in ar934x.dtsi to make use of that uart.
Reported-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
On AR934x this UART is usually not initialized by the bootloader
as it is only used as a secondary serial port while the primary
UART is a newly introduced NS16550-compatible.
In order to make use of the ar933x-uart on AR934x without RTS/CTS
hardware flow control, one needs to set the
UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this
UART is used as primary/console, the bootloader on AR934x typically
doesn't set those bits.
Setting them explicitely on AR933x does not do any harm, so just set
them unconditionally.
Tested-by: Chuanhong Guo <gch981213@gmail.com
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This new function make batch processing of network packets possible,
which slightly improves performance.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Tested-by: Rosen Penev <rosenp@gmail.com>
ar933x appears to have the same spi controller as ar934x but it's
not mentioned in datasheet at all. Use new spi driver instead to
gain more flash operating performance.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
A new shift mode was introduced since ar934x which has a way better
performance than current bitbang driver and can handle higher spi
clock properly. This commit adds a new driver to make use of this
new feature.
This new driver has chipselect properly configured and we don't need
cs-gpios hack in dts anymore. Remove them.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Remove read-only flag from U-boot environment partition for Netgear
WNDR3700 v1 and v2 so u-boot-envtools can modify data there.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
This commit adds support for the COMFAST CF-E560AC, an ap143 based
in-wall access point.
Specifications:
- SoC: Qualcomm Atheros QCA9531
- RAM: 128 MB DDR2 (Winbond W971GG6SB-25)
- Storage: 16 MB NOR (Winbond 25Q128JVSO)
- WAN: 1x 10/100 PoE ethernet (48v)
- LAN: 4x 10/100 ethernet
- WLAN1: QCA9531 - 802.11b/g/n - 2x SKY85303-21 FEM
- WLAN2: QCA9886 - 802.11ac/n/a - 2x SKY85735-11 FEM
- USB: one external USB2.0 port
- UART: 3.3v, 2.54mm headers already populated on board
- LED: 7x external
- Button: 1x external
- Boot: U-Boot 1.1.4 (pepe2k/u-boot_mod)
MAC addressing:
- stock
LAN *:40 (label)
WAN *:41
5G *:42
2.4G *:4a
- flash (art partition)
0x0 *:40 (label)
0x6 *:42
0x1002 *:41
0x5006 *:43
This device contains valid MAC addresses in art 0x0, 0x6, 0x1002 and
0x5006, however the vendor firmware only reads from art:0x0 for the LAN
interface and then increments in 02_network. They also jump 8 addresses
for the second wifi interface (2.4 GHz). This behavior has been duplicated
in the DTS and ath10k hotplug to align addresses with the vendor firmware
v2.6.0.
Recovery instructions:
This device contains built-in u-boot tftp recovery.
1. Configure PC with static IP 192.168.1.10/24 and tftp server.
2. Place desired image at /firmware_auto.bin at tftp root.
3. Connect device to PC, and power on.
4. Device will fetch flash from tftp, flash and reboot into new image.
Signed-off-by: August Huber <auh@google.com>
[move jtag_disable_pins, remove unnecessary statuses in DTS, remove
duplicate entry in 11-ath10k-caldata, remove hub_port0 label in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adapt Netgear WNDR3700v2 device identification string to ath79 naming
scheme by changing from 'wndr3700v2' to 'wndr3700-v2' (affects config,
makefile, init scripts and device tree definition).
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
This adds a shared definition Device/tplink-v2 to common-tp-link.mk.
Though currently only one device in ath79 uses it, putting it in
the common file seems more organized. The definitions are based
on the implementation in ramips target, where a lot of devices
is using tplink-v2-* commands already.
The '-V "ver. 2.0"' suffix for Archer D50 v1 can be removed because
it's default in Build/tplink-v2-image anyway.
While at it, add TPLINK_HWREVADD and TPLINK_HVERSION to DEVICE_VARS,
which seems to have been overlooked when adding Archer D50 v1.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This renames Device/tplink-loader-okli to Device/tplink-safeloader-okli
since the latter more accurately describes the combination of
tplink-safeloader and loader-okli use there. The old version might
be confused with other uses of the okli loader.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As we have tplink-v2-header and tplink-v2-image recipes as well,
this patch renames the Device/tplink definition to Device/tplink-v1,
as it's using the tplink-v1-* commands. This should provide easier
distinction in the future.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for the NanoStation Loco M2/M5 XW devices
on the ath79 target (support was long ago available on ar71xx).
Specifications:
- AR9342 SoC @ 535 MHz
- 64 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- AR8032 switch
- 2T2R 5 GHz radio, 22 dBm
- 13 dBi built-in antenna
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB
Flashing via TFTP:
- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
$ tftp 192.168.1.20
tftp> bin
tftp> trace
tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-xw-squashfs-factory.bin
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
There are several cases where phy-mode and status properties are
set again in DTS(I) files although those were set to the same values
in parent DTSI files already. Remove those cases (and thus also stop
their proliferation by copy/paste).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
A minority of ethernet-phy definitions seems to use numbers in label,
name and reg property relatively random. This patch aligns their
use to have the same numeric value for all of them.
While at it, improve order of properties/add newlines for the ethX
nodes where necessary.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This ports the GL.iNet 6408/6416 from ar71xx.
The GL-Connect GL.iNet v1 routers are basically a TP-Link TL-WR710N with
more DRAM/Flash and console/GPIO header in the same small form-factor.
Specifications:
- SoC: Atheros AR9331
- CPU: 400 MHz
- Flash: 8/16 MiB
- RAM: 64 MiB
- WiFi: 2.4 GHz b/g/n (SoC)
- Ethernet: 2x 100M ports (LAN/WAN)
- USB: 1x 2.0
The difference between 6408 and 6416 is just the flash size. It looks like
only the 16 MiB version has been advertised, while the 6408 is a modified
version. There are also 1-port versions sold by third parties.
Installation:
Install the sysupgrade image via stock firmware GUI or upload it via uboot
(web-based). The device will be available at 192.168.1.1.
Attention: In ar71xx, the same board name is used for both flash versions.
So, please make sure you flash the correct ath79 image when upgrading.
This has been device-tested on a GL.iNet 6416.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Based on a script for comparison, this fixes (hopefully) all errors
in SUPPORTED_DEVICES for ar71xx->ath79 upgrade.
Devices where old string is removed as the device does not exist
in ar71xx:
- dlink_dir-859-a1
- tplink_archer-a7-v5
- tplink_cpe510-v3
Devices where string is changed because it did not match the board
name in ar71xx:
- tplink_tl-mr3220-v1
- tplink_tl-mr3420-v1
- tplink_tl-wr2543-v1
- tplink_tl-wr741nd-v4
- tplink_tl-wr841-v7
- ubnt_unifiac-mesh
- ubnt_unifiac-mesh-pro
- ubnt_unifiac-pro
For this device, the correct string could not be found, but we could
not determine the correct one. Thus, the string is removed for now:
- tplink_tl-wr740n-v4
The script for checking this is quite simple (note that newer
entries, i.e. ath79->ath79 upgrade, are displayed as missing):
newpath=target/linux/ath79/image/
oldpath=target/linux/ar71xx/base-files/lib/ar71xx.sh
for s in $(grep -roh "SUPPORTED_DEVICES.*" $newpath | sed 's/SUPPORTED_DEVICES *.= *//'); do
found="Missing"
grep -q -r "\"$s\"" $oldpath && found="Found"
echo "$s: $found."
done
The errors might be filtered by appending 'grep "Missing"' to the script.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In certain cases, the uncompressed initramfs image will overwrite
the lzma-loader, which is currently only 10 MB away from kernel image
start. To prevent this, change LZMA_TEXT_START to 24 MB, so loader
and compressed image have 8 MB at the end of RAM and uncompressed
image has 24 MB available.
This is only enabled for ath79 at the moment, as there we can be sure
that all devices have 32+ MB RAM and TARGET_INITRAMFS_COMPRESSION_LZMA
is not enabled there.
Despite, since lzma-loader is currently build specifically for ath79
anyway, there is no need to re-specify LOADADDR and LZMA_TEXT_START
in image/Makefile, so the values are set directly in
image/lzma-loader/Makefile and the overwrite in image/Makefile is
removed.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This commit adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD
(wAP AC), a small weatherproof dual band, dual-radio 802.11ac
wireless AP with integrated omnidirectional anntennae and one
10/100/1000 Mbps Ethernet port.
See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9556
- RAM: 64 MB
- Storage: 16 MB NOR
- Wireless:
· Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae
· Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae
- Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port,
passive PoE in
Working:
- Board/system detection
- Sysupgrade
- Serial console
- Ethernet
- 2.4 GHz radio
- 5 GHz radio and LED
- Reset button
Not working/Unsupported:
- 2.4 GHz LED
- AP/CAP LED
- ZT2046Q SPI temperature and voltage sensor
This adds the basic features for supporting MikroTik devices:
- a common recipe for mikrotik images in common-mikrotik.mk
- support for minor (MikroTik NOR) split firmware (only for
generic subtarget so far)
Acknowledgments: Robert Marko <robimarko@gmail.com>
Andrew Cameron <apcameron@softhome.net>
Koen Vandeputte <koen.vandeputte@ncentric.com>
Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
In order to make the QCA955x SGMII workaround work, the unsuccessful
SGMII autonegotiation on the AR8033 should not block the PHY
state-machine.
Otherwise, the ag71xx driver never becomes aware of the copper-side
link-establishment and the workaround is never executed.
Signed-off-by: David Bauer <mail@david-bauer.net>
[remove one trailing whitespace per file]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds a workaround for the loss of the SGMII link observed on
the QCA955x generation of SoCs. The workaround originates part from the
U-Boot source code, part from the implementation from AVM found in the
GPL tarball for the AVM FRITZ!WLAN Repeater 450E.
The bug results in a stuck SGMII link between the PHY device and the SoC
side. This has only been observed with the Atheros AR8033 PHY and most
likely all devices using such combination are affected.
It is worked around by reading a hidden SGMII status register and
issuing a SGMII PHY reset until the link becomes useable again.
Signed-off-by: David Bauer <mail@david-bauer.net>
TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 550/391/195 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x internal antennas (embedded on PCB)
- 9x LED (all can be turned off with GPIO15), 2x button
- UART (J3) header on PCB
Flash instruction: use "factory" image directly in vendor GUI.
Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.
You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin
Stock firmware uses label MAC address for WiFi and same with local
bit set for ethernet. Since this is difficult to reproduce with
the toolset of OpenWrt, we just keep both ethernet and WiFi to
the same address here.
This is the first tiny device with tplink-safeloader in ath79.
Firmware partition is only 3648k and thus even smaller than for
the tplink-4m(lzma) devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The hack-patch which introduced the "at803x-disable-smarteee" for
disabling SmartEEE did in fact not disable SmartEEE but rather disabled
802.3az "standard" EEE.
This can be done by using the upstream properties "eee-broken-100tx" and
"eee-broken-1000t". EEE is then disabled by the PHY subsystem.
Tested on devolo WiFi pro 1200e.
Signed-off-by: David Bauer <mail@david-bauer.net>
This ports support for the TL-WA850RE v1 range extender from ar71xx
to ath79.
Specifications:
Board: AP123 / AR9341 rev. 3
Flash/RAM: 4/32 MiB
CPU: 535 MHz
WiFi: 2.4 GHz b/g/n
Ethernet: 1 port (100M)
Flashing instructions:
Upload the factory image via the vendor firmware upgrade option.
Recovery:
Note that this device does not provide TFTP via ethernet like many
other TP-Link devices do. You will have to open the case if you
require recovery beyond failsafe.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TPLINK_BOARD_NAME has been renamed to TPLINK_BOARD_ID a long time
ago (7d6c63d87542: "build: rename TPLINK_BOARD_NAME to
TPLINK_BOARD_ID" for ar71xx), and before introducing ath79 target
at all.
TPLINK_BOARD_NAME seems to have been introduced into ath79 target
only by mistake. It has never been used. Remove it.
Fixes: 53c474abbd ("ath79: add new OF only target for QCA MIPS silicon")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This device is an LTE router supported in ar71xx so far.
As per original commit, hardware specifications (v1.0 EU):
- SoC: QCA9531
- Flash: Winbond W25Q64FV (8MiB)
- RAM: EtronTech EM6AB160TSE-5G (64MiB)
- Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
- Ethernet: 2NIC (3x100M + 1x100M)
- WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
- Power: DC 12V 1A
Flashing instructions:
You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin
on 192.168.0.66/24, connect to any ethernet port and power on device while
holding the reset button). Flashing via OEM web interface does not work.
Known issues:
- LTE module does not always come up during boot (showing USB enumeration errors). Similar behavior has been reported at least from one user for ar71xx, too. Turning USB off and on again will serve as a workaround.
- eth0 (LAN) always shows carrier as 1 even if no cable is plugged in (this works "correctly" on ar71xx)
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
[several adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Filip Moc <lede@moc6.cz>
Kernel partition increase to 4 MiBs for Netgear WNDR3700v4 and WNDR4300
routers breaks sysupgrade image compatibility with ar71xx builds.
Therefore, SUPPORTED_DEVICES variable has to be removed for both devices
from target makefile.
Reported-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Using the led_ prefix for the node label is now common in ath79,
so also apply it here.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Using the LED of network interfaces for status (boot/failsafe/...)
indication is somewhat misleading, as the blinking might be
mistaken for network activity. This uses rssi LEDs instead, which
do not blink normally and thus are less ambiguous.
The rssihigh LED has also been used consistently for the TP-Link CPE
devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Do not put usb-phy into reset if clearing the usb-phy reset or
setting the suspend_override has failed.
Reorder (de)asserts like in arch/mips/ath79/dev-usb.c.
Add an optional reset_control "usb-phy-analog", which is needed for
ar934x SoCs like in the old mach-driver arch/mips/ath79/dev-usb.c.
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
Change the caldata partition DTS node label to be consistent with
the label property for some Netgear WNDR devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch introduces support for Netgear WNDR4500v3. Router
is very similar to WNDR4300v2 and is based on the same PCB.
Information gathered from various Internet sources (including
https://patchwork.ozlabs.org/patch/809227/) shows following
differences to WNDR4300v2:
* two USB 2.0 ports with separate LEDs
* USB LEDs soldered to secondary pads
* WPS and RFKILL buttons soldered to secondary pads
* described as N900 device with 3x3:3 MIMO for 2.4GHz radio
* power supply requirement is DC 12V 2.5A
* vendor HW ID suffix differs in one digit
* bigger chassis
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
This patch introduces support for Netgear WNDR4300v2.
Specification
=============
* Description: Netgear WNDR4300 v2
* Loader: U-boot
* SOC: Qualcomm Atheros QCA9563 (775 MHz)
* RAM: 128 MiB
* Flash: 2 MiB SPI-NOR + 128 MiB SPI-NAND
- NOR: U-boot binary: 256 KiB
- NOR: U-boot environment: 64 KiB
- NOR: ART Backup: 64 KiB
- NOR: Config: 64 KiB
- NOR: Traffic Meter: 64 KiB
- NOR: POT: 64 KiB
- NOR: Reserved: 1408 KiB
- NOR: ART: 64 KiB
- NAND: Firmware: 25600 KiB (see notes for OpenWrt)
- NAND: Language: 2048 KiB
- NAND: mtdoops Crash Dump: 128 KiB
- NAND: Reserved: 103296 KiB
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8337)
* Wireless:
- 2.4 GHz b/g/n (internal)
- 5 GHz a/n (AR9580)
* USB: yes, 1 x USB 2.0
* Buttons:
- Reset
- WiFi (rfkill)
- WPS
* LEDs:
- Power (amber/green)
- WAN (amber/green)
- WLAN 2G (green)
- WLAN 5G (blue)
- 4 x LAN (amber/green)
- USB (green)
- WPS (green)
* UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
* Power supply: DC 12V 1.5A
* MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2
Important Notes
===============
0. NOR Flash (2 MiB) is not touched by OpenWrt installation.
1. NAND Flash (128 MiB) layout under OpenWrt is changed as follows:
all space is split between 4 MiB kernel and 124 MiB UBI areas;
vendor partitions (language and mtdoops) are removed; kernel space
size can be further expanded if needed; maximum image size is set
to 25600k for compatibility reasons and can also be increased.
2. CPU clock is 775 MHz, not 750 MHz.
3. 5 GHz wireless radio chip is Atheros AR9580-AR1A with bogus PCI
device ID 0xabcd. For ath9k driver to load successfully, this is
overriden in DTS with correct value for this chip, 0x0033.
4. RFKILL button is wired to AR9580 pin 9 which is normally disabled
by chip definition in ath9k code (0x0000F4FF gpio mask). Therefore
'qca,gpio-mask=<0xf6ff>' hack must be used for button to work
properly.
5. USB port is always on, no GPIO for 5V power control has been
identified.
Installation
============
* TFTP recovery
* TFTP via U-boot prompt
* sysupgrade
* Web interface
Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_nand=y
CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr4300-v2=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
This commit adds support for the D-Link DIR-505, previously supported in
ar71xx.
Hardware
--------
SoC: Atheros AR9330
FLASH: 8M SPI-NOR
RAM: 64M
WIFI: 1T1R 1SS Atheros AR9330
LED: Power green, Status red
BTN: WPS, Reset
Installation
------------
Currently, installation is only possible by sysupgrading from an earlier
OpenWrt version, U-Boot TFTP or a modded U-Boot. I do not have the
original bootloader from D-Link on my device anymore, so i cannot test
the factory image.
Signed-off-by: David Bauer <mail@david-bauer.net>
The present U-Boot for GL-AR750S has a limit of 2 MB for kernel size.
While sysupgrade can manage kernels up to the present limit of 4 MB,
directly flashing a factory.img with a kernel size greater than 2 MB
through U-Boot will result in an unbootable device.
This commit uses the newly-introduced check-kernel-size build
operation to prevent the output of factory.img when the kernel
exceeds 2 MB in size, yet permits output of sysupgrade.img
as long as the kernel is within KERNEL_SIZE := 4096k
Cc: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
The memory hacks got removed from ath10k with 1e27bef ("mac80211: remove
ath10k_pci memory hacks"). As this device has low amount of RAM, switch
to ath-10k-ct small buffers variant, to avoid the OOM Reaper.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The Ubiquiti ToughSwitch 5XP is a 5-port PoE Gigabit switch with a single
Fast-Ethernet management port. It supports both 24V passive PoE out on all
five ports.
Flash: 8 MB
RAM: 64 MB
SoC: AR7242
Switch: ar8327
USB: 1x USB 2.0
Ethernet: 5x GbE, 1x FE
Installation of the firmware is possible either via serial + tftpboot or
the factory firmware update function via webinterface.
By default the single Fast-Ethernet port labeled "MGMT" is configured
as the WAN port. Thus access to the device is only possible via the
five switch ports.
Serial: 3v3 115200 8n1
The serial header is located in the lower left corner of the switches PCB:
```
|
|
|
| o
| o RX
| o TX
| o GND
|
|
++ +-++-+ ++ ++ +
+--+ ++ +--++--++--+
```
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
[remove ubnt,sw compatible - fix spelling - wrap commit message -
remove superfluous phy-mode property]
Signed-off-by: David Bauer <mail@david-bauer.net>
Flash: 8 MB
RAM: 64 MB
SoC: AR7242
Switch: bcm53128
USB: 1x USB 2.0
Ethernet: 8x GbE, 1x FE
The Ubiquiti ToughSwitch 8XP is a 8-port PoE Gigabit switch with a single
Fast-Ethernet management port. It supports both 24V passive PoE and 48V
802.11af/at PoE out on all eight ports.
By default the single Fast-Ethernet port labeled "MGMT" is configured as the
WAN port. Thus access to the device is only possible via the eight switch
ports.
Installation of the firware is possible either via serial + tftpboot or
the factory firmware update function via webinterface.
Serial: 3v3 115200 8n1
The serial header is located in the lower left corner of the switches PCB:
|
|
|
| o
| o RX
| o TX
| o GND
|
|
++ +-++-+ ++ ++ +
+--+ ++ +--++--++--+
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
[fix whitespace issue]
Signed-off-by: David Bauer <mail@david-bauer.net>
SW devices are Ubiquit ToughSwitch and EdgeSwitch series devices.
Hardware-wise they are very similar to the XM device series.
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
u-boot splits nand factory firmware at 2M offset, flash the first
part as kernel into spi nor and the other part as ubi into nand
flash. With previous commit increasing kernel size to 4M, generated
factory firmware is broken because ubi is at 4M offset.
This commit reduces kernel size definition to 2M in image Makefile,
producing proper factory image. Partition size in dts is kept
unchanged so that sysupgrade to a firmware with 2M+ kernel still
works.
Fixes: b496a2294c ("ath79: GL-AR750S: provide NAND support; increase kernel to 4 MB")
Reported-by: Jeff Kletsky <git-commits@allycomm.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This move the slightly different target-specific implementations of
mktplinkfw from the targets to include/image-commands.mk and renames
it to tplink-v1-image. Having a common version will increase
consistency between implementation and will complete the
tplink build command already present in the new location.
Due to the slight differences of the original implementations, this
also does some adjustments to the device build commands/variables.
This also moves rootfs_align as this is required as dependency.
Tested on:
- TL-WDR4300 v1 (ath79, factory)
- TL-WDR4900 v1 (mpc85xx, sysupgrade)
- RE210 v1 (ramips, see Tested-by)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Christoph Krapp <achterin@googlemail.com>
Both devices are available in 64M and 128M RAM configurations but there
is no visial indication which configuration one might get.
So just to be sure we properly support both configurations switch to
kmod-atk10k-ct-smallbuffers.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
Currently the patch only changes break to use goto statement instead.
But not necessary acutually since the ret value checked after the for loop.
So it is okay for the break case before changed by the patch also.
This patch only reverts the following commit partially.
https://github.com/openwrt/openwrt/commit/ddc11c3932c7b7b7df7d5fbd48f207e7
Note: The changes are mainly applied into the linux kernel upstream.
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
This adds a "factory" image for the aircube-isp devices. Note that the
firmware can't be uploaded without prior special preparation. For the
most recent instructions on how to do that, visit the OpenWRT wiki page
of the Ubiquiti airCube ISP for details:
https://openwrt.org/toh/ubiquiti/ubiquiti_aircube_isp
Current procedure:
With the original firmware 2.5.0 it is possible to upload and execute a
script via the configuration. To do that download and unpack the
original configuration, adapt uhttpd config to execute another lua
handler (placed in the config directory) and pack and upload it again.
The lua handler can call a script that mounts an overlayfs and modifies
the "fwupdate.real" binary so that an unsigned image is accepted. The
overlayfs is necessary because a security system (called tomoyo) doesn't
allow binaries in other locations than /sbin/fwupdate.real (and maybe
some more) to access the flash when executed via network.
A big thanks to Torvald Menningen (Snap) from the OpenWRT forum for
finding out how to patch the binary so that it accepts an unsigned
image.
The current step-by-step procedure is:
- Use a version 2.5.0 of the original firmware. This is important
because a binary file will be modified.
- Download a configuration.
- Unpack it (it's just a tar gz file without an ending).
- Add the following to uhttpd:
``````
config 'uhttpd' 'other'
list listen_http 0.0.0.0:8080
list listen_http [::]:8080
option 'home' '/tmp/persistent/config/patch/www'
option lua_prefix '/lua'
option lua_handler '/tmp/persistent/config/patch/handler.lua'
``````
- Create a `patch` subfolder.
- Create a `patch/www` subfolder.
- Create a `patch/handler.lua` with the following content:
``````
function handle_request(env)
uhttpd.send("Status: 200 OK\r\n")
uhttpd.send("Content-Type: text/plain\r\n\r\n")
local command = "/bin/sh /tmp/persistent/config/patch/patch.sh 2>&1"
local proc = assert(io.popen(command))
for line in proc:lines() do
uhttpd.send(line.."\r\n")
end
proc:close()
end
``````
- Create a `patch/patch.sh` with the following content:
``````
#!/bin/sh -x
set -e
set -u
set -x
UBNTBOX_PATCHED="/tmp/fwupdate.real"
MD5FILE="/tmp/patchmd5"
cat <<EOF > ${MD5FILE}
c33235322da5baca5a7b237c09bc8df1 /sbin/fwupdate.real
EOF
# check md5 of files that will be patched
if ! md5sum -c ${MD5FILE}
then
echo "******** Error when checking files. Refuse to do anything. ********"
exit 0
fi
# prepare some overlay functionality
LOWERDIR="/tmp/lower_root"
mkdir -p ${LOWERDIR}
mount -t squashfs -oro /dev/mtdblock3 ${LOWERDIR}
overlay_some_path()
{
PATH_TO_OVERLAY=$1
ALIAS=$2
UPPERDIR="/tmp/over_${ALIAS}"
WORKDIR="/tmp/over_${ALIAS}_work"
mkdir -p ${UPPERDIR}
mkdir -p ${WORKDIR}
mount -t overlay -o lowerdir=${LOWERDIR}${PATH_TO_OVERLAY},upperdir=${UPPERDIR},workdir=${WORKDIR} overlay ${PATH_TO_OVERLAY}
}
# patch the ubntbox binary.
overlay_some_path "/sbin" "sbin"
echo -en '\x10' | dd of=/sbin/fwupdate.real conv=notrunc bs=1 count=1 seek=24598
echo "******** Done ********"
``````
- Repack the configuration.
- Upload it via the normal web interface.
- Wait about a minute. The webserver should restart.
- Now there is a second web server at port 8080 which can call the lua
script. Visit the page with a web browser. Link is for example
http://192.168.1.1:8080/lua
- You should see the output of the script with a "*** Done ***" at the
end. Note that the patches are not permanent. If you restart the
router you have to re-visit the link (but not re-upload the config).
- Now you can upload an unsigned binary via the normal web interface.
Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
The factory image for the dlink_dir-615-e4 is getting too big which makes
the full ath79 tiny build fail, deactivate it by default.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The current ethernet MAC address setup of TL-WDR4300 board is different
from the setup of stock firmware:
OpenWrt: lan = label_mac -2, wan = label_mac -2
stock: lan = label_mac, wan = label_mac +1
The full address assignment is as follows:
LAN label
WAN label + 1
5G label
2G label - 1
This patch changes all devices using TL-WDR4300 board:
TL-WDR3600 v1 (checked on device)
TL-WDR4300 v1 (checked on device)
TL-WDR4300 v1 (IL)
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rephrase/extend commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This harmonizes the line wrapping in image Makefile device
definitions, as those are frequently copy-pasted and are a common
subject of review comments. Having the treatment unifying should
reduce the cases where adjustment is necessary afterwards.
Harmonization is achieved by consistently (read "strictly")
applying certain rules:
- Never put more than 80 characters into one line
- Fill lines up (do not break after 40 chars because of ...)
- Use one tab for indent after wrapping by "\"
- Only break after pipe "|" for IMAGE variables
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This enables using 4kiB sectors as erase blocks for 4MiB NOR flash ICs
that support it.
Writeable jffs2 overlay used to store settings requires a partition with
at least 5 erase blocks, so using small sectors is essential for devices
with 4MiB flash.
Sysupgrading a device running firmware without this feature will likely
not allow to preserve configs automatically but since ath79 is
considered to be in a "technology preview" state it shouldn't be a
problem.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Specifications:
- FCC ID: KA2IR615E3
- SoC: MIPS32 24K 400 MHz Atheros AR7240
- RAM: 32 MiB DDR SDRAM ESMT M13S2561616A-5T
- Flash: 4 MiB NOR SPI Macronix MX25L3208E
- Wireless: AR9287 2.4 GHz 802.11n 2T2R, 2x RP-SMA connectors
- Ethernet: 5x 100BASE-TX Fast Ethernet
- LEDs: 9x GPIO, 1x ath9k
- Buttons: 2x tactile switches
- UART: 3.3 V, 115200 8n1
- USB: simple hardware modification required, 1x USB 1.1 Full Speed
Partitioning notes:
Vendor firmware (based on CameoAP99) defines two additional partitions:
"mac" @0x3b0000, size 0x10000 and "lp" @0x3c0000, size 0x30000.
The "mac" partition stores LAN MAC address and hardware board name.
However, the vendor firmware uses addresses from "nvram" partition, and
the board name is used only for informational purposes in the Web
interface (included in the pages' header), not affecting the firmware
image check.
The "lp" partition is supposed to contain a "language pack" (which can
be used to add an additional language support to the Web interface) and
is flashed separately, using the vendor firmware upgrade page.
Since these partitions are absolutely useless for OpenWrt and
overwriting them doesn't prevent downgrading to obsolete vendor
firmware, this patch appends the valueable space to "firmware".
Installation instructions:
- Upgrade from OpenWrt ar71xx with "sysupgrade -f -n"
or
- Upload as a firmware update via the vendor Web-interface
or
- Connect UART and use "loady" to upload and run OpenWrt initramfs
image, then sysupgrade from it (TFTP client doesn't work)
or
- Before powering up hold "reset" button and keep it pressed for about
15 seconds after, then access fail safe Web server on 192.168.0.1 (the
old uIP TCP/IP protocol stack is not compatible with modern Linux, the
kernel, so you'll need to use some other OS to do this). Can be
performed without a Web-browser too:
curl http://192.168.0.1/cgi/index \
-F Send=@openwrt-ath79-tiny-dlink_dir-615-e4-squashfs-factory.bin
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Netgear WNDR routers (AR9344 models) like WNDR4300 have 128 MiB of flash
memory but only first 32 MiB are used now - both by vendor's firmware and
OpenWrt. This patch concatenates two regions of flash memory: ubi part
of firmware partition and reserved (unused) space beyond 'caldata_backup'
while preserving ART backup. No data is wiped or moved away.
This increases area for OS ubi volumes from 23 to 119 Megabytes.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
This partially reverts commit 32144ba275.
This commit replaced gpio-exports in favor of gpio-hogs for enabling USB
power at boot, but this rids the user of control of the USB port power
present on this device for a long time. It was agreed on a mailing list
[1] that this is not the way to go, and this patch breaks a very common
use-case of WWAN modem reset by power cycle, used on a lot USB equipped
routers, hence revert this change until a better solution can be found.
[1] http://lists.infradead.org/pipermail/openwrt-devel/2019-November/020151.html
Tested-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[adjusted commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label
Root access over serial line in vendor firmware: root/sohoadmin.
Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove size-cells from gpio-export]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TL-WDR4300 board uses only green LED names in DTSI.
This patch adds migration for them.
The actual LED colors on the devices have been reported to vary
across subrevisions (v1.x). Despite, the USB LEDs on the back might
have different color than the other LEDs on the front.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[extended commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The TL-WDR4300 v1 sold in Israel has a different TPLINK_HWID.
Thanks to Josh4300 for testing on device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The variables UBNT_BOARD and UBNT_VERSION are defined in the parent
Device/ubnt definition and then overwritten for most of the derived
platform definitions (e.g. Device/ubnt-wa).
Since this mixed use of inheritance and overwriting can be misleading,
this moves the variables to the platform-based definitions.
While at it, reorder the definitions to have order consistent, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The "/dts-v1/;" identifier is supposed to be put once at the beginning
of a device tree file. Thus, it makes no sense to provide it a second
time in to-be-included DTSI files.
This removes the identifier from all DTSI files in /target/linux.
Most of the DTS files in OpenWrt do contain the "/dts-v1/;". It is
missing for most of the following targets, though:
mvebu, ipq806x, mpc85xx, ipq40xx
This does not touch ipq806x for now, as the bump to 4.19 is close.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
"[...] the size component shall be zero."
(See "PCI Bus Binding to: IEEE Std 1275-1994 Rev 2.1"
section "4.1.1 Open Firmware-defined Properties for Child Nodes")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware:
* SoC: Atheros AR9342-BL1A
* RAM: 64MB DDR2 (Winbond W9751G6KB-25)
* Flash: 16MB SPI NOR (Macronix MX25L12835FZ2I-10G)
* Ethernet: 1x 10/100/1000 Mbps (Atheros AR8035-A) with 24V PoE support
* Wifi 2.4GHz: Atheros AR9340 v2
* WiFi 5GHz: Ubiquiti U-AME-G1-BR4A (rebranded QCA988X v2)
* LEDs: 1x Power, 1x Ethernet
* Buttons: 1x Reset
* UART: 1x TTL 115200n8, 3.3V RX TX GND, 3.3V pin closest to RJ45 port
The LEDs do not seem to be connected to any GPIO, so there is currently
no way to control them.
Installation via U-Boot, TFTP and serial console:
* Configure your TFTP server with IP 192.168.1.254
* Connect serial console and power up the device
* Hit any key to stop autoboot
* tftpboot 0x81000000 openwrt-ath79-generic-ubnt_litebeam-ac-gen2-initramfs-kernel.bin
* bootm 0x81000000
* copy openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin
to /tmp
* sysupgrade /tmp/openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The sysupgrade image contains OpenWrt specific metadata. Having this
metadata in the factory images makes no sense. Drop IMAGE/factory.bin
from Device/ubnt-wa and use the default from Device/ubnt instead.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In d421a8b944 ("ath79: read label MAC address from flash instead
of using phy0/phy1") the source of the label MAC address was changed
for devices just reading it from phy0. To get rid of the dependency
from phy startup, addresses were read directly from the flash
locations that are used to initialize the phy MAC addresses.
Unfortunately, it turned out that Ubiquiti XM devices seem to have
different flash locations than expected, and also seem to have
specific locations for different devices (all in art/EEPROM):
0xe012 AR9280 Nanostation M2 - 0x120c
0xe035 AR9280 Nanostation M3 - 0x120c
0xe1b2 AR9280 Rocket M2 - 0x120c
0xe1c3 AR9280 Rocket M3 - 0x120c
0xe1b5 AR9280 Rocket M5 - 0x120c
0xe2d5 AR9280 Bullet M2 Titanium - 0x120c
0xe2b5 AR9280 Nanobridge M5 - 0x120c
0xe202 AR9280 Bullet M2 - 0x120c
0xe232 AR9287 Nanobridge M2 - 0x110c
0xe4a2 AR9285 AirRouter - 0xa0bf
Picostation M2 - 0x120c and 0xa0bf
Nanostation Loco M2 - not in 0x120c, other locations not checked
An additional problem of the Ubiquiti device support in OpenWrt is
that we provide images that match several subvariants of the devices,
which might have different MAC address locations.
Given that reading the address from phy0 in 02_network _is_ working
for the ath79 target in general, it does not seem reasonable to
rebuild a complex MAC address retrieval mechanism which is already
present in the ath9k driver.
So, this patch reverts the label MAC address source for Ubiquiti XM
devices (and the Unifi AP) to /sys/class/ieee80211/phy0/macaddress.
This doesn't affect XW and Unifi AC devices, where the label MAC
address source is defined via device tree.
For alfa-network,ap121f the location 0x1002 is kept, as this has
been verified during device support preparation in PR #2199.
Fixes: d421a8b944 ("ath79: read label MAC address from flash
instead of using phy0/phy1")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch is based on #1689 and adds support for TP-Link Archer
C6 v2 (US) and A6 (US/TW).
The hardware is the same as EU and RU variant, except for GPIOs
(LEDS/Buttons), flash(chip/partitions) and UART being available
on the board.
- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q127CS1G (16MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
- 2.4GHz (bgn) QCA9563 integrated (3x3)
- 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: 115200, 8n1 (header available on board)
Known issues:
- Wireless: 5GHz is known to have lower RSSI signal, it affects speed and range.
Flash instructions:
Upload openwrt-ath79-generic-tplink_archer-c6-v2-us-squashfs-factory.bin
via the router Web interface.
Flash instruction using tftp recovery:
1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
tftp root directory renamed to ArcherA6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the
reset button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing
Flash partitioning: I've followed #1689 for defining the partition layout
for this patch. The partition named as "tplink" @ 0xfd0000 is marked
as read only as it is where some config for stock firmware are stored.
On stock firmware those stock partitions starts at 0xfd9400 however
I had not been able to make it functional starting on the same address as
on stock fw, so it has been partitioned following #1689 and not the stock
partition layout for this specific partition. Due to that firmware/rootfs
partition lenght is 0xf80000 and not 0xf89400 as stock.
According to the GPL code, the EU/RU/JP variant does have different GPIO pins
assignment to LEDs and buttons, also the flash memory layout is different.
GPL Source Code: https://static.tp-link.com/resources/gpl/gpl-A6v2_us.tar.gz
Signed-off-by: Anderson Vulczak <andi@andi.com.br>
[wrap commit message, remove soft_ver change for C6 v2 EU, move LED aliases
to DTS files, remove dts-v1 in DTSI, node/property reorder in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This renames all remaining occurrences of "EEPROM" to "art" to
further harmonize the partition labelling in ath79. This will
help to reduce the amount of user-space code and might be
beneficial when code is copy/pasted in the future.
Affected are only devices from Ubiquiti, where the XM board is
already using "art" in ath79.
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
YunCore XD4200 ('XD4200_W6.0' marking on PCB) is Qualcomm/Atheros based
(QCA9563, QCA9886, QCA8334) dual-band, Wave-2 AC1200 ceiling AP with PoE
(802.3at) support. A782 model ('T750_V5.1' marking on PCB) is a smaller
version of the XD4200, with similar specification but lower TX power.
Specification:
- QCA9563 (775 MHz)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100/1000 Mbps Ethernet (QCA8334), with 802.3at PoE support (WAN)
- Wi-Fi 2.4 GHz:
- XD4200: 2T2R (QCA9563), with ext. PA (SKY65174-21) and LNA
- A782: 2T2R (QCA9563), with ext. FEM (SKY85329-11)
- Wi-Fi 5 GHz:
- XD4200: 2T2R (QCA9886), with ext. FEM (SKY85728-11)
- A782: 2T2R (QCA9886), with ext. FEM (SKY85735-11)
- LEDs:
- XD4200: 5x (2x driven by SOC, 1x driven by AC radio, 2x Ethernet)
- A782: 3x (1x RGB, driven by SOC and radio, 2x Ethernet)
- 1x button (reset)
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x DC jack (12 V)
Flash instructions:
If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin
In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:
1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
seconds, recovery mode should start downloading image from server
(unfortunately, there is no visible indication that recovery got
enabled - in case of problems check TFTP server logs)
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
YunCore QCA9k based devices released in 2019 require a custom TFTP image
for U-Boot built-in recovery mode (triggered with reset button). Image
has to be prepended with 'YUNCORE' keyword followed by U-Boot CLI
commands which will be executed later. Images without the custom header
will be ignored by U-Boot.
To be able to support both the vendor firmware (QSDK) and OpenWrt flash
layouts, used here commands change the 'bootcmd' before flashing image.
This commit adds generic helper script for YunCore devices with 16 MB of
flash and enables TFTP image generation for A770 model.
Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com>
[pepe2k@gmail.com: commit description reworded, recipe renamed]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Daniel Golle
Adrian Schmutzler
David Bauer
Sven Roederer
Christian Buschau
Chuanhong Guo
Lech Perczak
Koen Vandeputte
Michal Cieslakiewicz
August Huber
Roger Pueyo Centelles
Enrico Mioso
Johann Neuhauser
Jeff Kletsky
Tomasz Maciej Nowak
Tobias Schramm
Christoph Krapp
Bjørn Mork
Tokunori Ikegami
Hauke Mehrtens
Christian Mauderer
Paul Fertser
Sungbo Eo
DENG Qingfang
Christian Lamparter
Stijn Tintel
Anderson Vulczak
Piotr Dymacz
Vincent Wiemann