brcm47xx does not use CONFIG_B53_SPI_DRIVER, but it could be selected if spi is build as a module
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37656
OCF_CRYPTOSOFT uses both symbols form crypto_hash and crypto_blkcipher,
so let it select these through kernel config.
Fixes the following build error:
ERROR: "crypto_alloc_ahash" [crypto/ocf/cryptosoft.ko] undefined!
ERROR: "crypto_ahash_digest" [crypto/ocf/cryptosoft.ko] undefined!
ERROR: "crypto_ahash_setkey" [crypto/ocf/cryptosoft.ko] undefined!
make[6]: *** [__modpost] Error 1
make[5]: *** [modules] Error 2
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 37652
This uses a new switch driver.
The old ADMTEK Adm6996 switch is not supported any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37650
This is untested, but probably needed to make it work with the phy lib switch driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37649
This is needed for some switches used on bcm47xx SoCs like the one on the Asus RT-N66U.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37645
bcm47xx_nvram_gpio_pin() returns a gpio pin number for a given name based
on configuration data in nvram.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37644
This commit adds the basic elements to support Poray brand routers.
It contains a tool to do the encryption/obfuscation that is used in
Poray routers.
Support for Poray devices was worked on by:
Felix Kaechele <heffer@fedoraproject.org>
Luis Soltero <lsoltero@globalmarinenet.com>
Michel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
SVN-Revision: 37635
Small router sold in EU: AR9330@400MHz, 1x USB2.0,
2x ethernet, 8MB flash, 32MB ram, one led, one button.
See: http://galeria.tech-blog.pl/TP-Link_TL-WR710N-EU/
[juhosg: use a separate kernel patch]
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3873/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37572
Mercury MW4530R is a TP-Link TL-WDR4310 clone but
with a much lower price tag (~ $40). This patch
is tested to work at trunk r37525.
Signed-off-by: Leon Xu <ylxu72@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3856/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37571
Mercury MW4530R is a TP-Link TL-WDR4310 clone but
with a much lower price tag (~ $40). This patch
is tested to work at trunk r37525.
Signed-off-by: Leon Xu <ylxu72@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3856/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37570
Looks like trunk@37090 has changed the logic that determines
if router's button was pressed. This resulted in TEW632BRP
always booting into failsafe mode because it detected pressed
button (which was not pressed).
Measure with voltmeter has shown that buttons on this router
are actually active-low. This patch reflects this fact in
board configuration and fixes 'load info failsafe mode' issue.
Note: it looks like Trendnet TEW632BRP and a close relative
to TEW-652BRP V1.0 and D-Link DIR-615C1, so same problem may
exist on those routers as well. This patch doesn't affect
routers other than 632BRP and unfortunately I do not have
hardware to test this issue with other routers.
This patch fixes#13893 and is tested on actuall Trendnet
TEW632BRP.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37569
Hauke Mehrtens
Jonas Gorski
John Crispin
Zoltan Herpai
Felix Fietkau
Luka Perkov
Gabor Juhos