The codepath seems to be only taken when using IPv6, so there should be
no negative side effects when IPv6 isn't loaded. I did not measure how
big the performance impact is.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 27237
It was originally tristate, but was changed to bool to prevent a build
breakage in an earlier patch revision (for a new syscall). The actual
commit[1] changed it in a way this isn't needed anymore, but
accidentially left the EXPORTFS change in. There's no reason for it
not being buildable as a module, so changing it back to tristate is
fine.
see: https://patchwork.kernel.org/patch/812832/
Thank you Jonas Gorski for the patch.
SVN-Revision: 27011
* Add missing config symbols
* Update package/kernel for 2.6.39
CONFIG_BT_L2CAP=y and CONFIG_BT_SCO=y are set to build them into the bluetooth module.
Thank you Jonas Gorski for the patch
SVN-Revision: 27010
* add md5sum for kernel
* add some missing config symbols
* add some ssb patches to make compat-wireless compile
Thank you Peter Wagner for the patch
SVN-Revision: 27009
Fixes for the following warnings:
drivers/mtd/devices/block2mtd.c: In function '_open_bdev':
drivers/mtd/devices/block2mtd.c:272:3: warning: ISO C90 forbids mixed declarations and code
drivers/mtd/devices/block2mtd.c: In function 'add_device':
drivers/mtd/devices/block2mtd.c:399:13: warning: assignment discards qualifiers from pointer target type
In the case of 442-block2mtd_probe.patch, it's not until the insertion of a executable statement before the definition that causes a warning, so I've chosen to resolve the issue here by splitting the definition and the initialization into a definition and a statement (and assignment) instead.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 27007
This patch adds 802.1Q VLAN support for the ADM6996M chip.
The driver is loaded for both the FC and M model. It will detect which of the
two chips is connected. The FC model is initialised, but no further
functionality is offered.
The PHY driver will always report "100 Mbit/s, link up", for both the M and FC
models. This reflects the fact that the link between switch chip and Ethernet
MAC is always on[1].
Further documentation can be found in the kernel's
Documentation/networking/adm6996.txt
Signed-of-By: Peter Lebbing <peter@digitalbrains.com>
SVN-Revision: 26865
SPIN_LOCK_UNLOCKED has been deprecated since 2.6.19 and will get removed
in 2.6.39, so replace it with DEFINE_SPINLOCK().
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26770
Use offset from struct mtd_part instead of struct mtd_partition for defining
the new partitions. This enables the usage of MTDPART_OFS_APPEND macro in
struct mtd_partition.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
SVN-Revision: 26705
These patches were submitted to netdev and will likely be out in 2.6.38.3.
In the meantime, they're needed in 2.6.37.6.
Patch by Philip Prindeville
SVN-Revision: 26616
Since the PHY driver is only used for the WAN port and there is virtually
no difference between it and the generic PHY driver, we can sefely remove
it.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26600
* Some module should be loaded later to load them after the modules they are depending on
* add some more missing config symbols
* make CS5535 build again
SVN-Revision: 26570
Jo-Philipp Wich
Hauke Mehrtens
Florian Fainelli
Felix Fietkau
John Crispin
Hamish Guthrie
Travis Kemen
Alexandros C. Couloumbis
Gabor Juhos