Apparently this modem replies differently to attempted --get-pin-status
which makes the script fail if a pincode is set. Fix this.
Manufacturer: Sierra Wireless, Incorporated
Model: MC7455
Revision: SWI9X30C_02.24.05.06 r7040 CARMD-EV-FRMWR2 2017/05/19 06:23:09
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Cherry-pick Multi-AP commits from uptream:
9c06f0f6a hostapd: Add Multi-AP protocol support
5abc7823b wpa_supplicant: Add Multi-AP backhaul STA support
a1debd338 tests: Refactor test_multi_ap
bfcdac1c8 Multi-AP: Don't reject backhaul STA on fronthaul BSS
cb3c156e7 tests: Update multi_ap_fronthaul_on_ap to match implementation
56a2d788f WPS: Add multi_ap_subelem to wps_build_wfa_ext()
83ebf5586 wpa_supplicant: Support Multi-AP backhaul STA onboarding with WPS
66819b07b hostapd: Support Multi-AP backhaul STA onboarding with WPS
8682f384c hostapd: Add README-MULTI-AP
b1daf498a tests: Multi-AP WPS provisioning
Add support for Multi-AP to the UCI configuration. Every wifi-iface gets
an option 'multi_ap'. For APs, its value can be 0 (multi-AP support
disabled), 1 (backhaul AP), 2 (fronthaul AP), or 3 (fronthaul + backhaul
AP). For STAs, it can be 0 (not a backhaul STA) or 1 (backhaul STA, can
only associate with backhaul AP).
Also add new optional parameter to wps_start ubus call of
wpa_supplicant to indicate that a Multi-AP backhaul link is required.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Those have by now been merged into wireless-drivers-next:
17ae2acd1a6f rt2x00: remove unneeded check
5991a2ecd070 rt2x00: remove confusing AGC register
9ad3b5565445 rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band
7aca14885ede rt2800: enable TX_PIN_CFG_RFRX_EN only for MT7620
c7ff1bfeaf1c rt2800: comment and simplify AGC init for RT6352
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Currently these kernel packages only work on x86, restrict them to that
target.
Fixes: 2f239c02a0 ("x86: video: add amdgpu DRM kernel package")
Fixes: 2f6918ee9b ("x86: video: add radeon DRM module support")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit e6d84fa886 as it breaks the
installation of the iproute2 utilities ip-bridge, ss, nstat, devlink and rdma
for the ip-full variant
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This reverts commit 26681fa6a6 as it breaks the
installation of the iproute2 utilities ip-bridge, ss, nstat, devlink and rdma
for the ip-full variant
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This reverts commit fc80ef3613 as it breaks the
installation of the iproute2 utilities ip-bridge, ss, nstat, devlink and
rdma for the ip-full variant
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This reverts commit 248797834b as it breaks the
installation of the iproute2 utilities ip-bridge, ss, nstat, devlink and rdma
for the ip-full variant
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Currently it seems impossible to configure /etc/config/dhcp to achieve
the following use case
- run dnsmasq with no-resolv
- re-generate /etc/resolv.conf with "nameserver 127.0.0.1"
Before this change, we have to set resolvfile to /tmp/resolv.conf.auto
to achive the 2nd effect above, but setting resolvfile requires noresolv
being false.
A new boolean option "localuse" is added to indicate that we intend to
use dnsmasq as the local dns resolver. It's false by default and to
align with old behaviour it will be true automatically if resolvfile is
set to /tmp/resolv.conf.auto
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
backport from wireless-drivers-next, replacing some existing patches in
our tree (marked with '=' are those which were already present):
f483039cf51a rt2x00: use simple_read_from_buffer()
=5c656c71b1bf rt2800: move usb specific txdone/txstatus routines to rt2800lib
=0b0d556e0ebb rt2800mmio: use txdone/txstatus routines from lib
=5022efb50f62 rt2x00: do not check for txstatus timeout every time on tasklet
=adf26a356f13 rt2x00: use different txstatus timeouts when flushing
=0240564430c0 rt2800: flush and txstatus rework for rt2800mmio
6eba8fd22352 rt2x00: rt2400pci: mark expected switch fall-through
10bb92217747 rt2x00: rt2500pci: mark expected switch fall-through
916e6bbcfcff rt2x00: rt2800lib: mark expected switch fall-throughs
641dd8068ecb rt2x00: rt61pci: mark expected switch fall-through
750afb08ca71 cross-tree: phase out dma_zalloc_coherent()
=c2e28ef7711f rt2x00: reduce tx power to nominal level on RT6352
a4296994eb80 rt2x00: Work around a firmware bug with shared keys
2587791d5758 rt2x00: no need to check return value of debugfs_create functions
pending on linux-wireless:
rt2x00: remove unneeded check
rt2x00: remove confusing AGC register
rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band
rt2800: enable TX_PIN_CFG_RFRX_EN only for MT7620
rt2800: comment and simplify AGC init for RT6352
rt2x00: do not print error when queue is full
rt2800: partially restore old mmio txstatus behaviour
rt2800: new flush implementation for SoC devices
rt2800: move txstatus pending routine
rt2800mmio: fetch tx status changes
rt2800mmio: use timer and work for handling tx statuses timeouts
rt2x00: remove last_nostatus_check
rt2x00: remove not used entry field
rt2x00mmio: remove legacy comment
While at it also rename some existing patches now that there are
separate folders with patches for each driver to make things a bit
nicer to handle.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This applies to kernel 4.10 and newer.
See 8db4c5be88
The above commit added to kernel 4.10 added new dependency
for building the NETFILTER_XT_MATCH_SOCKET (xt_socket.ko)
module. The NF_SOCKET_IPVx options (both of them) need to
be enabled in order to build the NETFILTER_XT_MATCH_SOCKET
module. Without the change the module is not built.
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
These two dependencies are mutual exclusive and it is only possible to
select one of them, change the select to a chose so it is only possible
to select one of them in OpenWrt menu config.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Applies a patch from https://github.com/openssl/openssl/pull/8213
that fixes an error where open /dev/crypto sessions were not closed.
Thanks to Ansuel Smith for reporting it.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
VBoxManage is not used and the image is created with proper permisions:
0f5d0f6 image: use internal qemu-img for vmdk and vdi images drop host
dependencies on qemu-utils and VirtualBox
Unreachable config symbols:
9e0759e x86: merge all geode based subtargets into one
No need to define those symbols since x86_64 is subtarget of x86:
196fb76 x86: make x86_64 a subtarget instead of a standalone target
Unreachable config symbols, so remove GRUB_ROOT:
371b382 x86: remove the xen_domu subtarget
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This updates mac80211 to backports version 4.19.23-1 which includes all
the stable fixes from kernel 4.19.23.
The removed patches are included in this version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Opkg treats text after a version number as higher than without:
~# opkg compare-versions "2.80rc1" "<<" "2.80"; echo $?
1
~# opkg compare-versions "2.80rc1" ">>" "2.80"; echo $?
0
This causes opkg not offering final release as upgradable version, and
even refusing to update, since it thinks the installed version is
higher.
This can be mitigated by adding ~ between the version and the text, as ~
will order as less than everything except itself. Since 'r' < 't', to
make sure that test will be treated as lower than rc we add a second ~
before the test tag. That way, the ordering becomes
2.80~~test < 2.80~rc < 2.80
which then makes opkg properly treat prerelease versions as lower.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
It was already enabled for wpad builds and since commit 6a15077e2d
the script relies on it. Size impact is minimal (2 kb on MIPS .ipk).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Minor bugfix release. Fixes for
* bc/dc
* sed (backslash parsing for 'w' command)
* ip (vlan fixes)
* grep (fixes for -x -v)
* ls (-i compat)
No need to refresh patches or config defaults
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SoC: Qualcomm IPQ4019 (Dakota) 717 MHz, 4 cores
RAM: 256 MiB (Nanya NT5CC128M16IP-DI)
FLASH: 128 MiB (Macronix NAND)
WiFi0: Qualcomm IPQ4019 b/g/n 2x2
WiFi1: Qualcomm IPQ4019 a/n/ac 2x2
WiFi2: Qualcomm Atheros QCA9886 a/n/ac
BT: Atheros AR3012
IN: WPS Button, Reset Button
OUT: RGB-LED via TI LP5523 9-channel Controller
UART: Front of Device - 115200 N-8
Pinout 3.3v - RX - TX - GND (Square is VCC)
Installation:
1. Transfer OpenWRT-initramfs image to the device via SSH to /tmp.
Login credentials are identical to the Web UI.
2. Login to the device via SSH.
3. Flash the initramfs image using
> mtd-write -d linux -i openwrt-image-file
4. Power-cycle the device and wait for OpenWRT to boot.
5. From there flash the OpenWRT-sysupgrade image.
Ethernet-Ports: Although labeled identically, the port next to
the power socket is the LAN port and the other one is WAN. This
is the same behavior as in the stock firmware.
Signed-off-by: Marius Genheimer <mail@f0wl.cc>
[Dropped setup_mac 02_network in favour of 05_set_iface_mac_ipq40xx.sh,
reorderd 02_network entries, added board.bin WA for the QCA9886 from ath79,
minor dts touchup, added rng to 4.19 dts]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
- Add the /etc/ssl/openssl.cnf as a separate package, to avoid breaking
the transitional mechanism, allowing libopenssl_1.0* and
libopenssl_1.1* to coexist.
- Remove the (selecting) dependency on @KERNEL_AIO
- Use global SOURCE_DATE_EPOCH
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
Add a patch to enable the option to change the default ciphersuite list
ordering to prefer ChaCha20 over AES-GCM. This is used by default for
all platforms, except for x86_64 and aarch64. The assumption is that
only the latter have AES-specific CPU instructions and asm code that
uses them in openssl. Chacha20Poly1305 is 3x faster than AES-256 in
systems without AES instructions, with an equivalent strength.
Disable error messages by default except for devices with small flash or
RAM, to aid debugging.
Disable ASM by default on arm platform with small flash. Size
difference on mips and powerpc, the other platforms with small flash
devices, are not really relevant (using 100K as a threshold). All of
the affected platforms are source-only anyway.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
This version adds the following functionality:
* TLS 1.3
* AFALG engine support for hardware accelleration
* x25519 ECC curve support
* CRIME protection: disable use of compression by default
* Support for ChaCha20 and Poly1305
Patches fixing bugs in the /dev/crypto engine were applied, from
https://github.com/openssl/openssl/pull/7585
This increses the size of the ipk binray on MIPS32 by about 32%:
old:
693.941 bin/packages/mips_24kc/base/libopenssl1.0.0_1.0.2q-2_mips_24kc.ipk
193.827 bin/packages/mips_24kc/base/openssl-util_1.0.2q-2_mips_24kc.ipk
new:
912.493 bin/packages/mips_24kc/base/libopenssl1.1_1.1.1a-2_mips_24kc.ipk
239.316 bin/packages/mips_24kc/base/openssl-util_1.1.1a-2_mips_24kc.ipk
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
Adds the following configuration options:
* using optimized assembler code (was always on before)
* use of x86 SSE2 instructions
* dyanic engine support
* include error messages
* Camellia, Gost, Idea, MDC2, Seed & Whirlpool algorithms
* RFC3779, CMS protocols
* VIA padlock hardware acceleration engine
Installs openssl.cnf with the library as it is used by engines
independent of the openssl util.
Fixes DTLS option that was innefective before.
Disables insecure SSL3 protocol and SHA0.
Adds openwrt-specific targets to Configure script, including asm support
for i386, ppc and mips64.
Strips building dirs from CFLAGS shown in binary.
Skips the fuzz directory during build.
Removed include/crypto/devcrypto.h that was included here, to use the
cryptodev-linux package, now that it was been moved from the packages
feed to the main openwrt repository.
This decreses the size of the ipk binray on MIPS32 by about 3.3%:
old:
706.957 bin/packages/mips_24kc/base/libopenssl1.0.0_1.0.2q-2_mips_24kc.ipk
199.294 bin/packages/mips_24kc/base/openssl-util_1.0.2q-2_mips_24kc.ipk
new:
693.941 bin/packages/mips_24kc/base/libopenssl1.0.0_1.0.2q-2_mips_24kc.ipk
193.827 bin/packages/mips_24kc/base/openssl-util_1.0.2q-2_mips_24kc.ipk
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
ucert needs to check the firmware part with metadata, but without the signature.
Use the new fwtool mode to extract that without altering the firmware image inside
the check
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This allows extracing the firmware + metadata from a signed firmware without
altering the original image file
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In the case of SHARED_LIBS=y, don't use -export-dynamic to place *all*
symbols into the dynamic symbol table. Instead, use --dynamic-list to
export a smaller set of symbols similar to that defined in static-syms.h
in the case of SHARED_LIBS=n, avoiding an 11 KB tc package size increase.
Also increment PKG_RELEASE.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This enables using the tc module m_xt.so, which uses the act_ipt kernel
module to allow tc actions based on iptables targets. e.g.
tc filter add dev eth0 parent 1: prio 10 protocol ip \
u32 match u32 0 0 action xt -j DSCP --set-dscp-class BE
Make the SHARED_LIBS parameter configurable and based on tc package
selection.
Fix a problem using the tc m_xt.so plugin as also described in
https://bugs.debian.org/868059:
Sync include/xtables.h from iptables to make sure the right offset is
used when accessing structure members defined in libxtables. One could
get “Extension does not know id …” otherwise. (See also: #868059)
Patch to sync the included xtables.h with system iptables 1.6.x. This
continues to work with iptables 1.8.2.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Simplify build and runtime dependencies on libelf, which allows tc and ip
to load BPF and XDP object files respectively.
Preserve optionality of libelf by having configuration script follow the
HAVE_ELF environment variable, used similarly to the HAVE_MNL variable.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Replace the old 'tc' with a singleton package variant which will be used
to enable additional functionality and limit it only to tc. Non-variant
packages will only be installed during 'tiny' variant builds, hence will
be configured without extra features, thus preserving previously limited
functionality and reduced package sizes.
Also set ip-tiny as the default variant, and install 'tiny' versions of
development libraries.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Daniel Golle
Arnout Vandecappelle (Essensium/Mind)
Hauke Mehrtens
Hans Dedecker
Yousong Zhou
Rosy Song
Paul Wassi
Oldřich Jedlička
Lucian Cristian
Peter Wagner
Pawel Dembicki
Eneas U de Queiroz
Tomasz Maciej Nowak
Rosen Penev
Deng Qingfang
Jonas Gorski
Felix Fietkau
Alin Nastac
Hannu Nyman
Marius Genheimer
Rafał Miłecki
Tony Ambardar