Commit Graph

75 Commits (bdb0de1bbce235244bcd0503c71886409379f4fc)

Author SHA1 Message Date
Matthias Schiffer 3d365831b0
ar71xx: reorganize kernel configuration
Rather than including all machines for the generic subtarget in the base
configuration, leave the base configuration without specific machines and
create a proper subtarget config for ar71xx/generic. The configuration
diffs of the mikrotik and nand subtargets get significantly shorter, as
will the configurations of future subtargets.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-01-13 19:54:45 +01:00
Gabor Juhos 09bb7105c2 ar71xx: sort kernel configurations
The symbols in some kernel configurations of the target are in
wrong order. Sort them with kconfig.pl.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-09 08:34:03 +01:00
Tim Thorpe 673793d753 ar71xx: add support for TP-Link TL-WR1043N v5
TP-Link TL-WR1043N v5 appears to be identical to the TL-WR1043ND v4,
except that the USB port has been removed and there is no longer a
removable antenna option.

The software is more in line with the Archer series in that it uses a
nested bootloader scheme.

Specifications:

 - QCA9563 at 775 MHz
 - 64 MB RAM
 - 16 MB flash
 - 3 (non-detachable) Antennas / 450 Mbit
 - 1x/4x WAN/LAN Gbps Ethernet (QCA8337)
 - reset and Wi-Fi buttons

Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
2017-11-14 22:36:46 +01:00
Piotr Dymacz c83bdd094e ar71xx: add support for Wallys DR342
Wallys DR342 is a 5 GHz, 2T2R AP/CPE board based on Atheros AR9342.

Short specification:

- 560/450/225 MHz (CPU/DDR/AHB)
- 1x Gbps Ethernet (AR8035) with passive PoE support (24-56 V)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 5 GHz with external FEM (SKY85728-11), up to 30 dBm
- 2x MMCX connectors
- miniPCIe connector with PCIe and USB 2.0 buses
- optional miniSIM slot
- 7x LED, 1x button
- UART, (E)JTAG and LED headers
- 1x DC jack for main power (12-56 V)

Flash instruction (do it under U-Boot, using UART):

1. tftp 0x82000000 lede-ar71xx-generic-dr342-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-11-14 22:36:46 +01:00
Felix Fietkau 2c9aff289e ar71xx: add support for Nokia WI2A-AC200i
Specifications:
 - SoC: Qualcomm QCA9558 (720 MHz)
 - RAM: 256MB
 - Storage: 1MB NOR, 128 MB NAND flash
 - Ethernet: 1x1000M

Installation:
 1. Connect to serial console on the board
 2. Boot initramfs image over u-boot
 3. Copy image to the device and run sysupgrade

Installation without serial console is not supported at this time

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-10-19 12:27:42 +02:00
Hauke Mehrtens 7bbf4117c6 ar71xx: Add kernel 4.9 support
This add support for kernel 4.9 to the ar71xx target.
It was compile tested with the generic, NAND and mikrotik subtarget.
Multiple members of the community tested it on their boards and did not
report any major problem so far.

Especially the NAND part received some changes to adapt to the new
kernel APIs. The serial driver hack used for the Arduino Yun was not
ported because the kernel changed there a lot.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-10-11 22:32:39 +02:00
Felix Fietkau f4a6daa5da ar71xx: unify CONFIG_CMDLINE
Booting from jffs2 directly is no longer supported, use
rootfstype=squashfs consistently for all subtargets

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-09-28 22:45:39 +02:00
Enrique Giraldo fefdb1e0b9 ar71xx: add support for COMFAST CF-E355AC
COMFAST CF-E355AC is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9531 + QCA9882.

Short specification:

- 2x 10/100 Mbps Ethernet, with PoE support
- 64MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, 802.11b/g/n
- 2T2R 5 GHz, 802.11ac/n/a
- built-in 4x 3 dBi antennas
- output power (max): 500 mW (27 dBm)
- 1x RGB LED, 1x button
- built-in watchdog chipset

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
[whitespace fixes, ac radio caldata offset fix]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-09-10 22:15:03 +02:00
Piotr Dymacz 90d8c0f0a2 ar71xx: add support for GL.iNet GL-USB150
GL.iNet GL-USB150 is an USB dongle WiFi router, based on Atheros AR9331.

Specification:

- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- Realtek RTL8152B USB to Ethernet bridge (connected with AR9331 PHY4)
- 1T1R 2.4 GHz
- 2x LED, 1x button
- UART header on PCB

Flash instruction:

Vendor firmware is based on OpenWrt CC. GUI or sysupgrade can be used
to flash LEDE firmware.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-09-10 22:14:43 +02:00
Piotr Dymacz 0c6165d21a ar71xx: add support for ALFA Network AP121F
ALFA Network AP121F is a pocket-size router dedicated for VPN/TOR users.
Device is based on Atheros AR9331 WiSoC and is running a custom version
(updated from OpenWrt CC to LEDE 17.01 release) of NetAidKit firmware.

Specification:

- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR1)
- 16 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz
- 1x microSD (optional, on separate PCB)
- 3x LED, 1x button, 1x switch
- UART header on PCB

Flash instruction (under U-Boot web recovery mode):

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with RJ45 port, press the reset button, power up device,
   wait for first blink of all LEDs (indicates network setup), then keep
   button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-22 23:13:55 +02:00
Piotr Dymacz 6165e4aab0 ar71xx: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.

Specification:

- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
  resitors are missing on TX/RX lines)
- 1x micro USB (for power only)

Flash instructions:

Use "factory" image under vendor GUI.

Recovery instructions:

This device contains tftp recovery mode inside U-Boot. You can use it to
flash LEDE (use "factory" image) or vendor firmware.

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ar71xx-generic-tl-wr902ac-v1-squashfs-factory.bin"
   to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
   and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.

Root access over serial line in vendor firmware: root/sohoadmin.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-04 08:58:54 +02:00
Piotr Dymacz 0a2e4204db ar71xx: generic: enable CONFIG_MTD_SPLIT_TPLINK_FW
We can use "tplink-fw" mtd splitter for TP-Link devices which use kernel
with TP-Link header embedded inside "safeloader" image type and thus get
rid of statically defined "kernel" and "rootfs" partitions in cmdline.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-04 08:58:54 +02:00
Piotr Dymacz f67ad17d19 ar71xx: refresh and cleanup nand subtarget kernel config
Refresh nand subtarget kernel config and enable kernel support for
boards which belong to this subtarget only.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-04 08:58:54 +02:00
Henryk Heisig b05c7193fd ar71xx: add support for TP-Link Archer C58 v1
TP-Link Archer C58 v1 is a dual-band AC1350 router, based on Qualcomm
QCA9561 + QCA9886. It looks like Archer C59 v1 without USB port.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 6x LED, 3x button
- UART header on PCB, RX, TX at TP4+5 (backside)

QCA9886 wlan needs pre_cal_data file and enable ieee80211 phy hotplug to
patch macaddress.

Flash instruction:

Use "factory" image directly in vendor GUI.

Recovery method:

1. Set PC to fixed ip address 192.168.0.66/24.
2. Download "lede-ar71xx-generic-archer-c58-v1-squashfs-factory.bin" and
   rename it to "tp_recovery.bin".
3. Start a tftp server with the file "tp_recovery.bin" in its root
   directory.
4. Turn off the router.
5. Press and hold Reset button.
6. Turn on router with the reset button pressed and wait ~15 seconds.
7. Release the reset button and after a short time the firmware should
   be transferred from the tftp server.
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:

tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b $fileaddr 0x9f020000 $filesize
reset

This commit is based on GitHub PR#1112

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-06-29 10:37:36 +02:00
Federico Cappon 9fec39a033 ar71xx: add support for TP-Link TL-WA855RE v1
TP-Link TL-WA855RE v1 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.

Short specification:

- 550/397/198 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x external antennas
- 2x LED (green and orange in the same package), 2x button
- UART: TP5(TX) and TP4(RX) test points on PCB

Flash instruction: use "factory" image directly in vendor GUI.

Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.

You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin

Image was tested only in EU version of the device, but should work
also with the same device version sold in other countries.

Signed-off-by: Federico Cappon <dududede371@gmail.com>
2017-06-29 10:37:36 +02:00
Mathias Kresin e7cd6f5d66 ar71xx: add AVM FRITZ!WLAN Repeater 300E support
Specifications:
* SoC: AR7242 (Virian 400MHz)
* RAM: 64 MB DDR (W9751G6JB-25)
* Flash: 16MB SPI flash (S25FL129PIF)
* WiFi: AR9382 (2.4/5GHz) + 2x SE2595L
* LAN: 1x1000M (PEF7071V)

To install LEDE via EVA bootloader, a FTP connection need to be
established to 192.168.178.1 within the first seconds after power on:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-24 22:36:38 +02:00
Ludwig Thomeczek b4711dbad3 ar71xx: add support for TP-Link Archer C25 v1
The TP-Link Archer C25 is a low-cost dual-band router.

Specification:

- CPU: Atheros QCA9561 775 MHz
- RAM: 64 MB
- Flash: 8 MB
- Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887
- NET: 5x 10/100 Mbps Ethernet

Some LEDs are controlled by an additional 74HC595 chip.

Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
[minor code style fixes, boards alphabetical order fixes,
reworked commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:18 +02:00
Serg Studzinskii b7cc661615 ar71xx: add support for TP-Link TL-WR942N v1
TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on
Qualcomm/Atheros QCA9561.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x USB 2.0
- 11x LED (most are controlled by 74HC595)
- 2x button
- UART header on PCB*

* Serial console is disabled in OEM non-beta firmwares and corresponding
  GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by
  production (non-beta) U-Boot and firmware.

Currently not working:

1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs
   by some U-Boot versions.

Flash instruction under vendor GUI:

1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin".
2. Go to WEB interface and perform usual firmware upgrade.

FLash instruction under U-Boot recovery mode (doesn't work in beta
firmware):

1. Setup PC with static IP "192.168.0.66/24" and tftp server.
2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make
   it available to download from your tftp server.
3. Press "reset" button and power up the router, wait till "WPS" LED
   turns on.

Flash instruction under U-Boot, using UART (can be done only with
preinstalled UART-enabled U-Boot version!):

1. Use "tpl" to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
   tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin
   erase 0x9f020000 +$filesize
   cp.b 0x81000000 0x9f020000 $filesize
   reset

Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
[minor code style fixes, extended commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:17 +02:00
Jo-Philipp Wich 66f25c98e0 ar71xx: disable ENS202EXT in mikrotik and nand subtargets
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-05-31 02:40:47 +02:00
Filip Moc a639cbfd00 ar71xx: Add support for TP-Link MR6400
You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin
on 192.168.0.66/24, connect to any ethernet port and power on device while
holding the reset button). Flashing via OEM web interface does not work.

Hardware Specification (v1.0 EU):
 - SoC: QCA9531
 - Flash: Winbond W25Q64FV (8MiB)
 - RAM: EtronTech EM6AB160TSE-5G (64MiB)
 - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
 - Ethernet: 2NIC (3x100M + 1x100M)
 - WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
 - Power: DC 12V 1A

Signed-off-by: Filip Moc <lede@moc6.cz>
2017-05-27 07:54:21 +02:00
Chris Blake 10d11859df ar71xx: add support for Aerohive AP-121
This adds support for Aerohive AP-121 access point.

Specification:
- SoC: Atheros AR9344-BC2A at 560MHz
- WiFi 1: 2.4GHz Atheros AR9340? - SoC
- WiFi 2: 5.0GHz Atheros AR9382-AL1A
- Memory: 128MB from 2x Nanya NT5TU32M16DG-AC
- SPI: 1MB Macronix MX25L8006E
- NAND: 128MB Hynix H27U1G8F2BTR-BC
- Ethernet: Atheros AR8035-A
- USB: 1x 2.0
- TPM: Atmel SC3204

Flashing:
1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter
a password of administrator or AhNf?d@ta06 if prompted.
2. Once in U-Boot, download and flash LEDE factory image over tftp:

dhcp;
setenv serverip tftp-server-ip;
tftpboot 0x81000000 lede-ar71xx-nand-hiveap-121-squashfs-factory.bin;
nand erase 0x800000 0x800000;
nand write 0x81000000 0x800000 0x800000;
reset;

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
[minor text changes in commit subject and description, fixed
alphabetical order in etc/diag.sh, use only model name in lib/ar71xx.sh,
fixed code style issues in mach-hiveap-121.c, ubinized factory image]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-15 22:58:59 +02:00
Mantas Pucka 68b5d34f69 ar71xx: add support for 8devices Rambutan development board
Rambutan is a Wifi module based on QCA9550/9557
http://www.8devices.com/products/rambutan

This commit adds basic support for Rambutan development kit

Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of DDR2 RAM
- 128 MB of NAND Flash
- 1x 100Mbps Ethernet
- 1x 1000Mbps Ethernet (PHY on dev-kit)
- 1x Wifi radio 2x2 MIMO, dualband 2.4 and 5 GHz
- 2x U.FL connectors on module, chip antennas on dev-kit
- 1x miniPCIe slot
- 1x USB2.0 host socket + 1x USB2.0 pins on 2.54mm header

Flash instructions:
Stock firmware is OpenWrt, so use:
 sysupgrade -n /tmp/lede-ar71xx-nand-rambutan-squashfs-sysupgrade.tar
or upgarde from GUI (don't save config)
Use factory image to flash from U-Boot:
 tftpboot 80060000 lede-ar71xx-nand-rambutan-squashfs-factory.ubi
 nand erase.part ubi
 nand write 80060000 ubi ${filesize}

Signed-off-by: Mantas Pucka <mantas@8devices.com>
[split support in uboot-envtools package into a separate commit,
fixed alphabetical order in lib/preinit/05_set_iface_mac_ar71xx]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-15 22:43:33 +02:00
Christian Mehlis dc4eae7a8c ar71xx: Compex WPJ563 support
Specification:
- SoC: Qualcomm Atheros QCA9563 (775 MHz, MIPS 74Kc)
- RAM: 128 MiB
- Storage: 16MB NOR flash
- Wireless: Built into QCA9563 (Dragonfly), PHY modes b/g/n, 3x3 MIMO
- Ethernet: 2x1G

Tested and working:
- ethernet / switch / lan / wan
- 2.4GHz SoC wifi
- PCIe
- leds
- buzzer

Ramload:
- tftpboot 0x84000000 lede-ar71xx-generic-wpj563-16M-initramfs-uImage.bin
- bootm 0x84000000

Install:
- tftpboot 0x80500000 lede-ar71xx-generic-wpj563-16M-squashfs-sysupgrade.bin
- erase 0x9f030000 +$filesize
- erase 0x9f680000 +1
- cp.b $fileaddr 0x9f030000 $filesize

Erasing 0x9f680000 is required because uboot defines
"bootcmd=bootm 0x9f680000 || bootm 0x9f030000", so it first tries to boot
the higher address. I think the 16 mb flash are intended to be used as
8+8mb for a fallback image. In my hardware only the lower address has a
bootable image. But to make sure future hardware will boot lede too, I
erase one block, so uboot will skip this address.

Signed-off-by: Christian Mehlis <christian@m3hlis.de>
2017-03-30 09:57:22 +02:00
Piotr Dymacz 4436979c83 ar71xx: add support for P&W R602N and CPE505N
P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also
labeled as R602F, R602, etc.) is a simple N300 router with 5-port
10/100 Mbps switch, non-detachable antennas and USB.

CPE505 is an outdoor CPE with PoE support and detachable antennas.

Both devices are based on Qualcomm/Atheros QCA9531 v2.

Common specification:

- 650/597/216 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- UART (J2) header on PCB

R602N specification:

- 5x 10/100 Mbps Ethernet
- 1x USB 2.0
- 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm
- 2x external, non-detachable antennas
- 7x LED, 1x button

CPE505N specification:

- 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V)
- 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm
- 2x external, detachable antennas (RP-SMA connectors)
- 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button

Flash instructions:

It seems that there are many different versions of the firmware which
these devices are shipped with. The generic/standard one is based on
some modified OpenWrt and LEDE firmware can be flashed directly from
vendor's webgui or with sysupgrade (root password is "admin123").

Before flashing, make sure (use "fw_printenv") that the kernel load
address in your device is set to "0x9f050000" (bootcmd variable is
"bootm 0x9f050000"). If your device uses different load address, you
should first change it, under vendor's firmware, with command:

fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS"

Where OLD_ADDRESS is previous kernel load address (in CPE505 version
I got access to, it was "0x9fe80000"). This will allow you to use
both the vendor's and LEDE firmware.

If version of your device contains empty U-Boot environment (you will
get information about this after issuing "fw_printenv"), you should
use U-Boot, serial line access and TFTP to perform firmware upgrade:

1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS"
5. saveenv && reset

These devices contain also web recovery mode inside U-Boot. It can be
started with pressing the reset button for around 3 seconds just after
the device powerup. Web recovery panel is available on "192.168.10.9"
and to be able to use it, IP on your PC must be set to "192.168.10.10".

Make sure to change kernel load address before using recovery mode or
the U-Boot will not be able to load LEDE firmware.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-23 17:59:47 +01:00
Vaclav Svoboda 0d9adb4832 ar71xx: add support for TP-LINK TL-WR840N v2 and v3
This patch adds support for the TP-LINK TL-WR840N v2 and v3.

- SoC: Qualcomm QCA9533-BL3A (650 MHz)
- RAM: 32 MiB (Zentel A3S56D40GTP)
- Flash: 4 MiB
   (v2: Macronix MX 25L323F)
   (v3: Winbond 25Q32FVSIG)
- LAN: 4x 100M
- WAN: 1x 100M

Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
2017-03-23 09:41:15 +01:00
Shuanglin Liu 53ef20f65a ar71xx: add support for Rockeetech AP531B0
Specification:
- SoC: Qualcomm Atheros QCA9531 (650/400/216 MHz (CPU/DDR/AHB))
- RAM: 64 MiB DDR2
- Storage: 16 MiB of flash (optional 16 MiB second flash)
- Wireless: built into QCA9531 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0) 1x100M (port 4)
- PCI-E: x1
- SIMcard slot: x1
- USB 2.0 port: x1 (optional)
- Ext GPIO pin: x8
- UART for serial console: x1
- External watchdog: x1 (optional)
- Power supply: 9-48V (DC jack/passive PoE)

Installation through tftp:
- Copy <Firmware Image Name> into tftp directory
- Connect board via ttl port and Ethernet port
- Boot the AP531B0
- When "Autobooting in 1 seconds" appears press Enter
- Set serverip and ipaddr appropriate
  (e.g. setenv serverip 192.168.88.10;setenv ipaddr 192.168.88.1)
- Enter "tftp 0x8050000 <Firmware Image Name>"
- Enter "erase 0x9f050000 +$filesize"
- Enter "cp.b 0x80500000 0x9f050000 $filesize"
- Enter "reset"

Signed-off-by: Shuanglin Liu <roboidler@gmail.com>
2017-03-12 17:38:31 +01:00
Karol Dudek 58fc50f1b0 ar71xx: add support for 8devices Lima board
Lima is a module for the (IoE) internet of everything applications,
based on Qualcomm/Atheros QCA4531.

Specification:

- 650/600/216 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 32 MB of FLASH
- 2T2R 2.4 GHz
- 2x 10/100 Mbps Ethernet
- USB 2.0 Host
- PCIe
- UART for serial console
- 14x GPIO

Flash instruction:
1. Download lede-ar71xx-generic-lima-squashfs-sysupgrade.bin
and rename it to 8dev_recovery.bin
2. Binary file copy to USB stick and plug into slot USB
3. Press S2 (reset) button
4. Press and hold the S1 button by 5 seconds
5. Wait ~40 seconds to complete recovery

Tested on:

- Lima development kit

Signed-off-by: Karol Dudek <karoiz@sli.pl>
2017-02-17 10:19:09 +01:00
Piotr Dymacz 56561b9f51 ar71xx: add support for TP-Link TL-WA850RE v2
TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.

Short specification:

- 550/391/195 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x internal antennas (embedded on PCB)
- 9x LED (all can be turned off with GPIO15), 2x button
- UART (J3) header on PCB

Flash instruction: use "factory" image directly in vendor GUI.

Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.

You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin

Image was tested only in US version of the device, but should work
also with the same device version sold in other countries.

Available FLASH space, with LEDE trunk, is only 240 KB.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-02-14 12:25:33 +01:00
Piotr Dymacz 670e14ed70 ar71xx: fix up nand subtarget kernel config
Disable all devices which do not belong to the nand subtarget.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-02-03 05:10:14 +01:00
Henryk Heisig e39dc8d823 ar71xx: add support to TP-Link Archer C59v1 and C60v1
TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- 8x LED (controled by 74HC595), 3x button
- UART header on PCB

TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Currently not working:
- Port LAN1 on C59, LAN4 on C60
- WiFi 5GHz (missing ath10k firmware for QCA9886 chip)
- Update from oficial web interface ( tplink-saveloader not support "product-info")

Flash instruction:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin
and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:

1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. reset

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-01-26 11:38:21 +01:00
Tal Keren 9c475eca3e ar71xx: add support for TP-Link RE450
Add full support for TP-Link RE450.
The wireless SoC is similiar to Archer C7: QCA9558 + QCA9880 (pci).
The ethernet interface is AR8035, but the mdio is connected to the gpio and
the chipset builtin mdio bus isn't used, which is unique (and weird), so the
kernel gpio mdio module is used.
The two ethernet leds are connected to the GPIO, so they are both configured,
one to indicate link status and the other to indicate data transfer.

The generation of the image was added to the image Makefile.
The return value of tplink-safeloader is not ignored anymore (to fail on error)

The result factory image is flashable from the stock web ui.

Signed-off-by: Tal Keren <kooolk@gmail.com>
[rd@radekdostal.com: ar71xx: RE450: do not build RE450 for nand]
Signed-off-by: Radek Dostál <rd@radekdostal.com>
[hyniu@o2.pl: ar71xx: RE450: Renaming LED accordance with the standard]
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[jo@mein.io: squash fixes from Radek and Henryk into original commit]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-12-22 14:50:05 +01:00
Ludwig Thomeczek 1a4d07c2c5
ar71xx: add support for TP-LINK WR1043ND v4
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
2016-12-20 14:38:48 +01:00
David Lutz aada15af93
ar71xx: add support for TP-LINK TL-WR940N v4
Signed-off-by: David Lutz <kpanic@hirnduenger.de>
2016-12-16 11:12:46 +01:00
Felix Fietkau a5923cd549 ar71xx: remove PB92 reference design board support
Due to flash size limitations, support for this board has not been
functional for years

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Felix Fietkau 30285facbe ar71xx: remove AP113 reference design board support
Due to flash size limitations, support for this board has not been
functional for years

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Felix Fietkau 4c8a9b8e39 ar71xx: remove AP81 reference design board support
This board is very old and unlikely to still be relevant today.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Felix Fietkau 441ee62931 ar71xx: remove AP83 reference design board support
This board is very old and unlikely to still be relevant today. Support
for it contains a significant amount of device specific baggage which is
worth getting rid of.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Rafał Miłecki 0658527e1e switch to the new usbport LED trigger
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-19 12:09:45 +02:00
Matthias Schiffer 594f0e80ce
ar71xx: add kernel support for D-Link DIR-869 A1
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-11 22:58:36 +02:00
Felix Fietkau c6c81351b7 ar71xx: add missing profile for the nand subtarget (FS#56)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-21 13:58:47 +02:00
Jo-Philipp Wich 8d1218ca73 ar71xx: merge profiles into image building code
- Remove old style device profiles and convert them to device definitions
  within the image building code

- Fix the legacy build macros for the changed eval depth in the legacy
  image build wrapper

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-06-27 11:10:15 +02:00
John Crispin 3874773503 Revert "ar71xx: fix legacy image building"
This reverts commit 59e98b27c9.

and

Revert "ar71xx: merge profiles into image building code"

This reverts commit 636089ead6.

these are still causing issues

Signed-off-by: John Crispin <john@phrozen.org>
2016-06-23 19:33:31 +02:00
John Crispin 636089ead6 ar71xx: merge profiles into image building code
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-22 19:32:06 +02:00
Jo-Philipp Wich 473e9cad43 ar71xx: add missing kernel symbol (#21849)
Also reorder subtarget kernel configs.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 48717
2016-02-12 19:55:07 +00:00
John Crispin cede06cebc ar71xx: Support for Ubiquiti UniFi AP AC LITE
Add support for the Ubiquiti UniFi AP AC LITE
Signed-off-by: P.Wassi <p.wassi at gmx.at>

SVN-Revision: 48711
2016-02-12 08:31:32 +00:00
Felix Fietkau 3f184882e8 ar71xx: Kernel board definition for PowerCloud CR5000
Kernel part of support for the PowerCloud Systems CR5000.  The
    CR5000 is a dual-band 802.11n wireless router with 8MB flash,
    64 MB RAM, (unused in stock firmware) USB 2.0 port, and five
    port gigabit ethernet switch.  The CR5000 was sold as hardware for
    the Skydog cloud-managed router service.

Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>

SVN-Revision: 47940
2015-12-19 11:27:32 +00:00
Felix Fietkau eef3b7acfb ar71xx: Kernel board definition for PowerCloud CR3000
Kernel part of support for PowerCloud CR3000.  The CR3000 is
    a 802.11n 2.4 GHz wireless router with 8MB flash, 64MB RAM,
    a four port fast ethernet switch, and a fast ethernet wan port which
    was sold by PowerCloud Systems as hardware for the Skydog
    cloud-managed router service.

Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>

SVN-Revision: 47939
2015-12-19 11:27:25 +00:00
Felix Fietkau 4cc541756d ar71xx: Kernel board definition for PowerCloud CAP324
Kernel part of support for PowerCloud CAP324 Cloud AP.
    The CAP324 Cloud AP was a device sold by PowerCloud Systems as hardware for
    the CloudCommand service for 'cloud' based managment of large numbers
    access points.

    The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
    and 128MB RAM and single gigabit ethernet port.  It can be powered via PoE
    or a power adaptor.

Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>

SVN-Revision: 47938
2015-12-19 11:27:19 +00:00
John Crispin abc84551c0 ar71xx: add support for Cisco's MR18
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>

Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>

SVN-Revision: 47878
2015-12-12 06:42:29 +00:00
John Crispin b98205c946 ar71xx: Add support for AP147-010 reference board
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46457
2015-07-24 09:09:42 +00:00