Commit Graph

89 Commits (ae27cbf98b151b815414eaa6dca7dcf6343b6ac2)

Author SHA1 Message Date
Roman Yeryomin f4e5880d0f ramips: preliminary support for 4.14
- removed upstreamed patches
- 0901-spansion_nand_id_fix.patch is disabled, not clear if it's needed

Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: John Crispin <john@phrozen.org>
2018-02-15 10:46:39 +01:00
Mathias Kresin 7985bf23ef ramips: drop stray kernel 4.4 configs
The kernel 4.4 patches where already removed with the bump to 4.9. Drop
the the subtarget configs as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-27 09:17:25 +02:00
Alex Maclean f683385e73 ramips: add support for TP-Link RE350
The TP-Link RE350 is a wall-wart AC1200 range extender/access point with
a single gigabit ethernet port and two non-detachable antennas, based on
the MT7621A SoC with MT7603E and MT7612E radios.

Firmware wise it is very similar to the QCA based RE450.

SoC: MediaTek MT7621A (880MHz)
Flash: 8MiB (Winbond W25Q64)
RAM:   64MiB (DDR2)
Ethernet: 1x 1Gbit
Wireless: 2T2R 2.4Ghz (MT7603E) and 5GHz (MT7612E)
LEDs: Power, 2.4G, 5G (blue), WPS (red and blue), ethernet link/act
(green)
Buttons: On/off, LED, reset, WPS

Serial header at J1, 57600 8n1:
Pin 1 TX
Pin 2 RX
Pin 3 GND
Pin 4 3.3V

Factory image can be uploaded directly through the stock UI.

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2017-07-25 21:02:53 +02:00
John Crispin fddc78bc11 ramips: bump to v4.9
Signed-off-by: John Crispin <john@phrozen.org>
2017-07-06 06:37:03 +02:00
Stijn Tintel 880f73c327 kernel: cleanup CONFIG_SCHED_HRTICK
Remove CONFIG_SCHED_HRTICK from target configs, as it was added to the
generic config in b47fd76563.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-06-29 04:46:59 +02:00
Sergey Ryazanov 68e7a2a0b7 kernel: disable CONFIG_SG_POOL by default
CONFIG_SG_POOL symbol is selected only by CONFIG_SCSI, since the last
one is disabled by default then disable CONFIG_SG_POOL by default too.
And explicitly enable it only for platforms that use CONFIG_SCSI.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2017-06-07 18:31:10 +02:00
John Crispin 9bc9457b85 ramips: fixup nand support on v4.9
Signed-off-by: John Crispin <john@phrozen.org>
2017-06-01 12:30:17 +02:00
Daniel Golle d17cb4a68a ramips: purge default packages on MT7621
In order to have a smaller initramfs image remove all packages not
needed on all devices and add them explicitely for those actually
needing them. Also remove wpad-mini from ramips default package set
and add it to all sub-targets except for MT7621.
While at it reorder packages alphabetically and replace kmod-mt76 with
kmod-mt7603 and/or kmod-mt76x2 depending on the chip actually used on
a specific board.

Hopefully fixes FS#758

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-05-04 14:13:23 +02:00
Paul Spooren 414b65db85 ramips: enable ramdisk for mt7621
Fixes #758

Signed-off-by: Paul Spooren <paul@spooren.de>
2017-05-04 00:51:05 +02:00
John Crispin 6cb0372d42 ramips: fix mt7621 ethernet support for v4.9
Signed-off-by: John Crispin <john@phrozen.org>
2017-02-15 09:12:00 +01:00
Felix Fietkau f5977c0c0a ramips: revert faulty 4.4 config change from 9c24227090
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-14 13:47:21 +01:00
John Crispin 9c24227090 ramips: add v4.9 support
NAND support is missing

Signed-off-by: John Crispin <john@phrozen.org>
2017-02-14 12:17:52 +01:00
Rosen Penev 80768ddccd ramips: Add I2C driver to the default kernel config
I made a commit that added the RTC driver to the kernel config with
the intent that it would fix hctosys. Unfortunately while the RTC
driver is in there, it's connected through I2C, the driver for which
comes in module form and is thus loaded late. After this commit, it
works fine.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2017-01-15 17:43:05 +01:00
Felix Fietkau 018d80007e kernel: remove ubifs xz decompression support
It has been unused, and less useful than squashfs for cases where flash
space usage matters.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-09 14:07:06 +01:00
Rosen Penev 369884c2a1 ramips: Add RTC driver to kernel for working hctosys
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2016-10-31 16:41:26 +01:00
Rafał Miłecki 0658527e1e switch to the new usbport LED trigger
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-19 12:09:45 +02:00
Mathias Kresin eb88a9cacb ramips: fix wrong blocksizes
The D-Link DIR-860L B1 has a flash chip which doesn't support
4K sectors. Since the DIR-860L B1 was the only mt7621 board which had
the 4k blocksize set, the 4K sector support is removed from the kernel
config.

I've checked the flash chips of all boards having set a 4K blocksize
again. This time I searched harder to finding bootlogs instead of
relying on wikis articles and/or the device tree source file.

The Planex MZK-DP150N has an en25q32b instead of the mentioned one in
the dts. Albeit the en25q32b supports 4K sectors, 4K support is not
enabled in the driver. Change the blocksize for this board back to 64K.

Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-15 09:53:37 +02:00
Mathias Kresin 925e63e71f ramips: enable 4K sector support in kernel config
This is a follow up to 28110727f1
"ramips: set blocksize for 4MB devices". I've missed to include the
required changes of the kernel configs to enable 4K sector size
support.

The option is only enabled for targets having boards with 4k sector
size flash chips.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-13 22:06:08 +02:00
Jonas Gorski b962da4d92 ramips: mt7621: switch to 24kc
1004kc is just a SMP capable 34kc, and GCC treats 24kc and 34kc exactly
the same and will generate identical code, so there is no need to tune
to 1004kc instead of 24kc.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2016-08-23 11:55:32 +02:00
John Crispin 281483e097 ramips: enable nand support for mt7621
this makes sysupgrade work on the ERX

Signed-off-by: John Crispin <john@phrozen.org>
2016-08-03 15:30:13 +02:00
Felix Fietkau 9abbaa9539 build: remove MIPS dsp/dsp2 CPU_SUBTYPE
There does not seem to be any meaningful difference in generated code.
This will save some time and space on snapshot builds

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-08-03 14:56:45 +02:00
Jo-Philipp Wich b051ac76e8 ramips: mt7621: add missing kernel symbol
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-07-16 13:59:12 +02:00
Álvaro Fernández Rojas 604b92dbd0 ramips: fix the number of uarts for each SoC
- Use default number of uarts (2) for rt288x/rt305x/rt3883/mt7620.
- Allow up to 3 uarts on MT7621 and MT7628.
- Remove unneeded SERIAL_8250_RT288X for MT7628.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-03 12:20:33 +02:00
John Crispin 5d0eff9801 ramips: set default profile to priority 1
doing so will sort all profiles alphabetically

Signed-off-by: John Crispin <john@phrozen.org>
2016-05-14 21:27:16 +02:00
Felix Fietkau 27dfe64887 ramips/mt7621: remove cflags override
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-14 17:58:43 +02:00
John Crispin 825717d450 ramips: convert mt7621 to new image building code
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-12 03:29:36 +02:00
Andrew Yong 374cae9e6f ramips: add initial support for SamKnows SK-WB8
Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-05-12 03:29:35 +02:00
Jo-Philipp Wich e885286834 target: globally remove ARCH_PACKAGES overrides
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-04-17 19:55:09 +02:00
John Crispin cb049e71cd ramips: Add support for the Netgear WNDR3700v5
https://wiki.openwrt.org/toh/netgear/wndr3700

wndr3700v5 uses the single-core dual thread MediaTek MT7621S SoC.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 49247
2016-04-26 11:43:53 +00:00
John Crispin 30fbc1a4d1 ramips: Add support for ZBT WG3526
The WG3526 is the follow-up to the 2626 and is mostly the same, with the
excaption that the mt7602 has been replaced with the mt7603. The internal wifi
setup has also changed slightly. Based on my tests, everything that worked on
the 2626 works on the 3526 and with roughly the same performance.

v1->v2:
* Remove some references to 2626 that I had missed in the dts.

v2->v3:
* Update patch to match new file structure.
* Removed SD driver to be consistent with other MT7621 targets.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>

SVN-Revision: 49213
2016-04-21 19:47:08 +00:00
John Crispin 8b8dfeb027 ramips: Disable the SD driver by default on MT7621
The SD driver has been a long and dragging issue on the MT7621 platforms as it hasn't worked for
months resulting in unbootable devices. Until it's fixed, disable it in the default profiles.

Reports / Discussed here:

https://dev.openwrt.org/ticket/21392
https://dev.openwrt.org/ticket/21834
https://dev.openwrt.org/ticket/21995
https://forum.openwrt.org/viewtopic.php?id=59092

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>

SVN-Revision: 49131
2016-04-09 10:25:03 +00:00
John Crispin e626a0d877 ramips: mt7621: fix Ubiquiti EdgeRouter X profile
Remove unnecessary packages to reduce image size so it fits in initramfs (to enable upgrading from factory firmware).

Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 49127
2016-04-09 10:24:47 +00:00
John Crispin 37f1022d73 ramips: mt7621: sync MQmaker WiTi profile name to dts name
Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 49126
2016-04-09 10:24:44 +00:00
Felix Fietkau f73d8fb81b ramips: fix subtarget kernel version assignment (only mt7621 is ready for now)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48953
2016-03-07 17:05:03 +00:00
Felix Fietkau d041e8b44b ramips: add linux 4.4 support, update mt7621 subtarget to 4.4
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48951
2016-03-07 16:33:34 +00:00
Felix Fietkau 6f8d647778 ramips: re-enable highmem support for MT7621 now that it's fixed
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48469
2016-01-24 00:16:32 +00:00
John Crispin b4bb10b3a0 ralink: update config files to build the cleaned up ethernet driver
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47902
2015-12-17 09:26:20 +00:00
John Crispin 4e31b2e869 ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX)
This router is based on MT7621 SoC, no wifi, no usb, nand.

Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.

Doesn't work:
* No GPIO leds. All leds are controlled by switch,
  but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
  nand/spi drivers do not support pin sharing,
  so it is not accessable and disabled. Stock
  firmware could read it and it was empty.
* PoE out.

Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.

U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.

Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47881
2015-12-12 07:38:06 +00:00
John Crispin e610cdfc8a ramips: use gic timer as clocksource for mt7621
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
  Will work on proper frequency detection later.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47875
2015-12-12 06:42:05 +00:00
Felix Fietkau 77bedbe80d Revert "ramips: use gic timer as clocksource for mt7621"
This reverts commit 270a2afcc544ca14e79198346e7e186033472ae7.

SVN-Revision: 47872
2015-12-11 19:22:15 +00:00
John Crispin 9f14006809 ramips: add additional support for MQmaker WiTi board
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram,
2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and
one 5 ghz antenna.

This is the 6th submission that adds support for XHCI in the device tree
file, along with switching the location of the 2 radio's and addition of
the kmod-i2c-mt7621 in the default packages of the profile.

Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>

SVN-Revision: 47845
2015-12-11 15:04:13 +00:00
John Crispin abd11be13c ramips: use gic timer as clocksource for mt7621
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
  Will work on proper frequency detection later.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47843
2015-12-11 15:03:39 +00:00
John Crispin a87272ebfb ramips: enable CPS for mt7621
Enables CPS multiprocessing instead ob obsoleted CMP for mt7621.

This patch fixes a few issues currently existing on 4.3 kernel with at least ubnt-erx:
* iperf shows only 50Mbits on direct gigabit connection to desktop,
* ping times jump to 5-6ms to dorectly connected desktop
* /proc/interrupts shows spurious interrups (ERR)

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47842
2015-12-11 15:03:27 +00:00
John Crispin 6df4426245 ralink: bump to the target to v4.3
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47831
2015-12-10 19:06:32 +00:00
John Crispin 7b4acdeff6 ralink: renable nand support
CONFIG_MTK_MTD_NAND was incorrectly disabled by r47619.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47640
2015-11-24 22:00:55 +00:00
John Crispin 8c1f5141ce ralink: add support for netis WF-2881
netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN.
It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.

this device only works on top of UBI.

Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons (reset button)
* ethernet switch and USB diag LEDs
* UART
* GPIOs
* sysupgrade

Tested and not working
* failsafe

Signed-off-by: YounJae Rho <luxflow@live.com>

SVN-Revision: 47619
2015-11-24 18:29:26 +00:00
Felix Fietkau b95aed986a ramips: minor fixes for mt7621 profiles
* remove references to non-existing kmod-usb3-mt7621
 * ZTB WG2626 doesn't have an RTC (thanks to Piotr Dymacz!)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47407
2015-11-07 12:51:48 +00:00
John Crispin 165244a222 ramips: add support for ZBT WG2626
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47351
2015-11-02 10:18:19 +00:00
Felix Fietkau d9857f5468 ramips: Enable RTC support for PBR-M1
The PBR-M1 and other upcoming MT7621 boards have RTC chips on them. The
PBR-M1 also selects the kmod-rtc-pcf8563 by default. But the module itself
will not be build because CONFIG_RTC_CLASS is currently not enabled for its
kernel.

Enabling this option should fix the problem of the missing rtc device on
these boards.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46857
2015-09-11 16:32:58 +00:00
Jonas Gorski efb2c403cf ramips: disable the openwrt commandline hack
We don't make use of it, so no need to have it enabled.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46759
2015-08-30 12:18:14 +00:00