hak5
/
openwrt
mirror of https://github.com/hak5/openwrt.git
1
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
45,990 Commits
5 Branches
29 Tags
205 MiB
Commit Graph

23 Commits (ad65d9d7b264d6d17293c59469e770905d2f785a)

Author SHA1 Message Date
Piotr Dymacz bc173ddd83 ramips: support dual image feature on ALFA Network boards 
New U-Boot version for MediaTek MT76x8/MT762x based ALFA Network boards
includes support for a 'dual image' feature. Users can enable it using
U-Boot environment variable 'dual_image' ('1' -> enabled).

When 'dual image' feature is enabled, U-Boot will modify DTB and divide
the original 'firmware' flash area into two, equal in size and aligned
to 64 KB partitions: 'firmware' and 'backup'. U-Boot will also adjust
size of 'firmware' area to match installed flash chip size.

U-Boot will load kernel from active partition which is marked with env
variable 'bootactive' ('1' -> first partition, '2' -> second partition)
and rename both partitions accordingly ('firmware' <-> 'backup').

There are 3 additional env variables used to control 'dual image' mode:
- bootlimit   - maximum number of unsuccessful boot tries (default: '3')
- bootcount   - current number of boot tries
- bootchanged - flag which informs that active partition was changed; if
                it is set and 'bootcount' reaches 'bootlimit' value,
                U-Boot will start web-based recovery which then updates
                both partitions with provided image

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
 2019-11-13 21:45:31 +01:00
Adrian Schmutzler f4c3cfc620 ramips: read label MAC address from flash instead of using phy0/phy1 
This replaces all uses of $(cat /sys/class/ieee80211/phyX/macaddress)
by retrieval from the proper flash locations. This will make
02_network independent of WiFi setup again.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
 2019-11-13 12:51:38 +01:00
Adrian Schmutzler 1c321237c2 ramips: split further base-files across subtargets 
As started in 19724e28c8 ("ramips: split base-files into
subtargets"), this moves some smaller left-over files to the
appropriate base-files folder of their subtarget:

- /etc/init.d/bootcount
- /etc/uci-defaults/04_led_migration

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
 2019-11-11 14:53:06 +01:00
Adrian Schmutzler d2b9333ea9 ramips: remove default case for MAC address assignment 
So far, MAC address assignment in ramips has contained a default
case, which defined wan_mac = eth0 + 1 for _every_ device not
having an explicit case there.

This is not desirable, as many device supporters will just not
care or know about this definition, so another MAC address will be
introduced by accident. In some cases the wan_mac is assigned
although it is not needed, in other cases even addresses not
dedicated to the device will be used (e.g. wan_mac actually is
eth0 - 1, but during support nobody cared, so eth0 + 1 is used now,
which might actually belong to another device ...).

Thus, in this PR the former default case is converted to an
explicit case. This one comprises all devices not being accounted
for by other cases, reduced by those not having wan at all.
The big number of entries for this node might be another indication
that many of them wouldn't actually be there if there hadn't been
default wan_mac setup.

In exchange, the current "do nothing" case can be removed, as it
will be the new default case.

The devices being put in the newly created explicit case were
determined as follows:

1. Create a list of all devices based on the DTS files.

2. Remove all devices already having an explicit entry setting
   their address.

3. Remove all devices that only have lan set up in the first part
   of 02_network:

mt7620:
   - alfa-network,tube-e4g
   - asus,rp-n53
   - buffalo,wmr-300
   - comfast,cf-wr800n
   - edimax,ew-7476rpc
   - edimax,ew-7478ac
   - elecom,wrh-300cr
   - hnet,c108
   - kimax,u25awf-h1
   - kimax,u35wf
   - kingston,mlw221
   - kingston,mlwg2
   - microduino,microwrt
   - netgear,ex2700
   - netgear,ex3700
   - netgear,wn3000rp-v3
   - planex,cs-qr10
   - planex,mzk-ex300np
   - planex,mzk-ex750np
   - ravpower,wd03
   - sercomm,na930
   - yukai,bocco
   - zbtlink,zbt-cpe102
   - zte,q7

mt7621:
   - gnubee,gb-pc1
   - gnubee,gb-pc2
   - linksys,re6500
   - mikrotik,rbm11g
   - netgear,ex6150
   - thunder,timecloud
   - tplink,re350-v1
   - tplink,re650-v1

mt76x8:
   - alfa-network,awusfree1
   - d-team,pbr-d1
   - glinet,vixmini
   - vocore,vocore2-lite
   - tama,w06
   - tplink,tl-mr3020-v3
   - tplink,tl-wa801nd-v5
   - tplink,tl-wr802n-v4
   - tplink,tl-wr902ac-v3
   - vocore,vocore2
   - widora,neo-16m
   - widora,neo-32m

rt288x:
   - buffalo,wli-tx4-ag300n
   - dlink,dap-1522-a1

rt305x:
   - allnet,all0256n-4m
   - allnet,all0256n-8m
   - allnet,all5002
   - allnet,all5003
   - alphanetworks,asl26555-16m
   - alphanetworks,asl26555-8m
   - asus,wl-330n
   - aximcom,mr-102n
   - dlink,dcs-930
   - easyacc,wizard-8800
   - hame,mpr-a2
   - hootoo,ht-tm02
   - huawei,d105
   - intenso,memory2move
   - planex,mzk-dp150n
   - rt305x dlink,dcs-930l-b1
   - sparklan,wcr-150gn
   - tenda,3g150b
   - tenda,3g300m
   - tenda,w150m
   - trendnet,tew-638apb-v2
   - unbranded,a5-v11
   - vocore,vocore-16m
   - vocore,vocore-8m
   - wansview,ncs601w
   - zorlik,zl5900v2

rt3883:
   - loewe,wmdr-143n
   - omnima,hpm

4. Put the remaining devices in the new case.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
 2019-11-06 13:17:25 +01:00
Adrian Schmutzler 19724e28c8 ramips: split base-files into subtargets 
While most of the target's contents are split into subtargets, the
base-files are maintained for the target as a whole.

However, OpenWrt already implements a mechanism that will use (and
even prefer) files in the subtargets' directories. This can be
exploited to make several scripts subtarget-specific and thus save
some space.

In certain cases, keeping files in parent (=target) base-files was
more convenient, and thus no splitting was performed for those.

Note that this will increase overall code lines, but reduce code
per subtarget.

base-files ipk size reduction:
master (mt7621)   60958 B
split (mt7620)    46358 B (- 14.3 kiB)
split (mt7621)    48759 B (- 11.9 kiB)
split (mt76x8)    44948 B (- 15.6 kiB)
split (rt288x)    43508 B (- 17.0 kiB)
split (rt305x)    45616 B (- 15.0 kiB)
split (rt3883)    44176 B (- 16.4 kiB)

Run-tested on:
GL.iNet GL-MT300N-V2 (mt76x8)
D-Link DWR-116 (mt7620)

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
 2019-11-03 00:26:17 +01:00
Adrian Schmutzler 794d4b6652 treewide: remove kmod-usb-core from DEVICE_PACKAGES 
This removes _all_ occurrences of kmod-usb-core from
DEVICE_PACKAGES and similar variables.

This package is pulled as dependency by one of the following
packages in any case:
- kmod-usb-chipidea
- kmod-usb-dwc2
- kmod-usb-ledtrig-usbport
- kmod-usb-ohci
- kmod-usb2
- kmod-usb2-pci
- kmod-usb3

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[remove kmod-usb-core from EnGenius ESR600]
Signed-off-by: David Bauer <mail@david-bauer.net>
 2019-10-06 21:28:49 +02:00
Sungbo Eo 2678ba9093 ramips: add support for ipTIME A604M 
ipTIME A604M is a 2.4/5GHz band AC1200 router, based on MediaTek
MT7628AN.

Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7612EN
- Ethernet: 5x 10/100Mbps
  - Switch: SoC internal
- UART:
  - J1: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
 2019-08-17 23:52:34 +08:00
Chuanhong Guo 7a8d3432c7 ramips: use upstream RAW_APPENDED_DTB instead of our OWRTDTB 
Upstream kernel added support for RAW_APPENDED_DTB on ralink arch
in the following commit:
02564fc89d3d ("ralink: Introduce fw_passed_dtb to arch/mips/ralink")

Use upstream solution and get rid of our OWRTDTB hack.
This commit set DEVICE_DTS to $$(DTS) instead of replacing DTS with
DEVICE_DTS in device profile because DTS variable will be dropped
in later commits.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on mt7621/mt76x8]
Tested-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on rt305x/mt7620]
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
 2019-07-08 22:00:24 +02:00
David Bauer b19c48dc34 ramips: enable R6120 USB power 
Enable the USB power for the Netgear R6120. Otherwise, no power is
supplied to an attached USB device.

Signed-off-by: David Bauer <mail@david-bauer.net>
 2019-04-06 19:14:06 +02:00
Mathias Kresin 8293aec943 ramips: disable CONFIG_MTD_SPLIT_FIRMWARE 
It's no longer needed as all mt7621 devices use DT binding (supported by
upstream mtd code) for specifying "firmware" part format explicitly.

Signed-off-by: Mathias Kresin <dev@kresin.me>
 2019-01-26 21:46:33 +01:00
Chen Minqiang 295b37d207 ramips: mt76x8: select only the matching mt76 driver 
Select the matching mt76 driver for the PCI wireless of the following
devices:

 - HiWiFi HC5861B
 - Mercury MAC1200R v2.0
 - Netgear AC1200 R6120
 - Buffalo WCR-1166DS
 - ZyXEL Keenetic Extra II
 - Wavlink WL-WN575A3

Because every device has selected the corresponding mt76 driver, we can
include kmod-mt7603 instead of the mt76 metapackage, which used for the
wireless of the mt7628 and mt7688 WiSoC.

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
[select kmod-mt7603 as target default package, add wireless driver for
WL-WN575A3]
Signed-off-by: Mathias Kresin <dev@kresin.me>
 2018-12-06 12:17:25 +01:00
Mathias Kresin 80c61c161a treewide: use wpad-basic for not small flash targets 
Add out of the box support for 802.11r and 802.11w to all targets not
suffering from small flash.

Signed-off-by: Mathias Kresin <dev@kresin.me>

Mathias did all the heavy lifting on this, but I'm the one who should
get shouted at for committing.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
 2018-10-16 15:07:41 +01:00
Mathias Kresin cf7154db07 kernel: only optimized for size if small_flash 
Add a new config option to allow to select the default compile
optimization level for the kernel.

Select the optimization for size by default if the small_flash feature is
set. Otherwise "Optimize for performance" is set.

Add the small_flash feature flag to all (sub)targets which had the
optimization for size in their default kernel config.

Remove CC_OPTIMIZE_FOR_* symbols from all kernel configs to apply the new
setting.

Exceptions to the above are:

  - lantiq, where the optimization for size is only required for the
    xway_legacy subtarget but was set for the whole target
  - mediatek, ramips/mt7620 & ramips/mt76x8 where boards should have
    plenty of space and an optimization for size doesn't make much sense
  - rb532, which has 128MByte flash

Signed-off-by: Mathias Kresin <dev@kresin.me>
 2018-07-12 18:15:32 +02:00
Sergey Ryazanov 67a3cdcbb0 kernel: enable THIN_ARCHIVES by default 
THIN_ARCHIVES option is enabled by default in the kernel configuration
and no one target config disables it. So enable it by default and remove
this symbol from target specific configs to keep them light.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
 2018-05-22 07:55:20 +02:00
Sergey Ryazanov bdc2b58c4b kernel: enable FUTEX_PI by default 
New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols
are enabled. Both of these symbols are enabled by default in the
generic config, so enable FUTEX_PI by default too to keep platform
specific configs minimal.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
 2018-05-22 07:55:12 +02:00
Sergey Ryazanov a08b0d0c31 kernel: enable EXPORTFS by default 
OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have
OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config
of 4.14 and remove this option from platform specific configs.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
 2018-05-22 07:55:05 +02:00
Sergey Ryazanov 978543a246 kernel: disable DRM_LIB_RANDOM by default 
DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST
which is disable by default, so disable DRM_LIB_RANDOM by default too.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
 2018-05-22 07:54:57 +02:00
Sergey Ryazanov ead26e9db6 kernel: disable DMA_{NOOP|VIRT}_OPS by default 
These options do not used by any supported arch, so disable them by
default to make arch configs a bit more clean.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
 2018-05-22 07:54:49 +02:00
Sergey Ryazanov f928c338ad kernel: disable ARCH_WANTS_THP_SWAP by default 
Only one arch (x86_64) enables this option. So disable
ARCH_WANTS_THP_SWAP by default and remove referencies to it from all
configs (except x86_64) to make them clean.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
 2018-05-22 07:54:42 +02:00
Felix Fietkau dea9922acd ramips: drop linux 4.9 support 
4.14 has been tested a lot by a number of users, and we want to use it
for the release.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
 2018-04-06 18:21:45 +02:00
Felix Fietkau 46c49d8381 kernel: optimize for performance by default starting with 4.14 
Keep size optimizations for smaller targets that already switched

Signed-off-by: Felix Fietkau <nbd@nbd.name>
 2018-02-24 16:05:28 +01:00
Roman Yeryomin f4e5880d0f ramips: preliminary support for 4.14 
- removed upstreamed patches
- 0901-spansion_nand_id_fix.patch is disabled, not clear if it's needed

Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: John Crispin <john@phrozen.org>
 2018-02-15 10:46:39 +01:00
L. D. Pinney 3e36ca4b43 ramips: merge mt7628/mt7688 into mt76x8 
The ramips subtargets of mt7628 and mt7688 dts files all #include "mt7628an.dtsi"

They are essentially a single subtarget.

This patch merges the ramips subtargets mt7628 and mt7688 into a single subtarget mt76x8.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
 2017-08-30 17:05:10 +02:00