6acfae9379
ar71xx: enable ar7240 switch support on the UBNT NanoStation M Fixes broadcast frames on the second ethernet MAC
...
Signed-off-by: Alexander Couzens <lynxis@c-base.org>
SVN-Revision: 24723
2010-12-19 11:56:42 +00:00
b512523d6f
ar71xx: fix micrel phy patch (Patch from #8041.)
...
SVN-Revision: 24718
2010-12-19 10:05:55 +00:00
96da72dc56
generic: fix min/max confusion in jffs2_sum_init on 2.6.32
...
SVN-Revision: 24652
2010-12-17 20:34:26 +00:00
cafe08a1b2
ar71xx: remove stray semicolons
...
SVN-Revision: 24651
2010-12-17 17:57:20 +00:00
01c76bf128
ar71xx: fix WLAN LEDs on the DIR-825 board
...
SVN-Revision: 24650
2010-12-17 17:10:21 +00:00
c1d3a23d19
ar71xx: add helper function to setup ath9k LED/GPIO on the AP94 based boards
...
SVN-Revision: 24649
2010-12-17 17:10:19 +00:00
e7ea6387a3
ar71xx: use usbdev trigger for USB LEDs by default
...
SVN-Revision: 24648
2010-12-17 17:10:16 +00:00
a059a11ee1
generic: add LED trigger for USB device presence/activity
...
SVN-Revision: 24646
2010-12-17 17:10:11 +00:00
3b8a79395a
generic: add usb_find_device_by_name helper
...
SVN-Revision: 24645
2010-12-17 17:10:08 +00:00
0d01356fc6
generic: nuke 2.6.33 specific stuff, is not used by any platform
...
SVN-Revision: 24644
2010-12-17 17:10:04 +00:00
8390b7dc9b
ar71xx: UBNT Secondary MAC address duplicate fix
...
There is Secondary MAC address duplicate problem with some UBNT
RouterStation and RouterStation Pro HW batches as Primary MAC addresses
are not increased by 2 per device in board data. Fix is to use 'Locally
Administrated bit' for Secondary MAC address instead of increasing
Primary MAC addresses by 1 which could overlap with other device
Primary MAC address.
Signed-off-by: Kestutis Barkauskas<keba@devint.net>
SVN-Revision: 24643
2010-12-17 17:10:01 +00:00
a26c3e60e2
ar71xx: populate LED configuration for WZR-HP-G300NH
...
Signed-off-by: Dave Lichterman <laviddichterman@gmail.com>
[nand-disk trigger has been removed - juhosg]
SVN-Revision: 24642
2010-12-17 17:09:57 +00:00
9daa5485ba
brcm47xx: add ssb debug option.
...
This fixes a problem with wrt350n.
It boots only if this config option is set, otherwise it reboots after "Switching to clocksource MIPS"
Thank you sn9 for fixing this problem.
SVN-Revision: 24626
2010-12-16 19:35:59 +00:00
1da5dcbb7a
brcm47xx: add some missing pci ID for tg3 driver
...
Broadcom removed these pci id, but at least the wrt350n has a Ethernet
controller with a pci id of 14e4:1676
Thank you sn9 for fixing this problem.
SVN-Revision: 24625
2010-12-16 19:31:05 +00:00
c58d8a369c
brcm47xx: this patch went upstream
...
SVN-Revision: 24624
2010-12-16 19:26:55 +00:00
a2a5598c00
ar71xx: add wlan led for the TL-WR941ND
...
SVN-Revision: 24612
2010-12-15 19:55:50 +00:00
e421d2575f
ar71xx: UBNT M-Series MAC address fix
...
UBNT M-Series devices have 2 MAC addresses in board data.
Fix is to use both entries from board data instead of one entry.
Signed-off-by: Kestutis Barkauskas<keba@devint.net>
SVN-Revision: 24611
2010-12-15 19:55:47 +00:00
87f73331a4
revert r24604
...
SVN-Revision: 24605
2010-12-15 12:24:27 +00:00
164c97838a
target/linux: clean up non generic & obsolete kernel options for 2.6.36, 2.6.37
...
SVN-Revision: 24604
2010-12-15 12:15:46 +00:00
6c1ace2f28
ar71xx: init the LED pin for ath9k on the TL-MR3[24]20 boards
...
SVN-Revision: 24569
2010-12-14 18:01:04 +00:00
a7750dae90
ar71xx: add helper function to setup LED pin and GPIO on the AP91 based boards
...
SVN-Revision: 24568
2010-12-14 18:01:00 +00:00
5e3e1d4a02
* make the usb gpio configurable * 105-header_xway.patch has a corrupt line count in it
...
SVN-Revision: 24564
2010-12-14 13:02:49 +00:00
d2fdd1dbe1
ramips: remove 2.6.3[24] support
...
SVN-Revision: 24562
2010-12-14 08:00:31 +00:00
1403850be1
ramips: switch to 2.6.36
...
SVN-Revision: 24561
2010-12-14 08:00:29 +00:00
f9898e30fb
ramips: handle OTG interrupt on the RT305x SoC
...
SVN-Revision: 24560
2010-12-14 08:00:25 +00:00
1f002efd98
bump kernel version, add MAINTAINER entry
...
SVN-Revision: 24559
2010-12-14 07:58:24 +00:00
d4bf98f231
add plemininary ultrasparc support
...
SVN-Revision: 24558
2010-12-14 07:57:22 +00:00
5495be1421
Update package selection
...
SVN-Revision: 24544
2010-12-13 12:59:22 +00:00
81edc28358
enable mach support for OpenRD Base and OpenRD Client ( #8417 ), spare the rest
...
SVN-Revision: 24541
2010-12-13 10:06:40 +00:00
5a351509aa
base-files: use shutdown instead of stop when the system goes down (patch by tripolar)
...
SVN-Revision: 24540
2010-12-13 08:01:21 +00:00
9f47e80bb3
adds new lantiq kernel. once the codebase is fully tested and know to be working on all the devices previously supported by ifxmips, we will drop ifxmips support.
...
SVN-Revision: 24526
2010-12-12 22:57:16 +00:00
b8ab3d34eb
kernel: update kernel versions Update kernel 2.6.32.26 to 2.6.32.27 Update kenrel 2.6.36.1 to 2.6.36.2
...
SVN-Revision: 24486
2010-12-11 16:07:21 +00:00
9f38f9bf76
ar71xx: add missing files for the JA76PF board
...
SVN-Revision: 24444
2010-12-10 19:55:28 +00:00
44e22cbd49
Fixed Comtrend CT536_CT5621 board settings. These boards are based on the 96348GW-11 reference design but have different GPIOs therefore we use the board fixups now availabed (thanks the patches by Jonas Gorski) to create a separate board entry for these boards and leave the reference design with reference GPIOs. Also these boards only have enet1 (no enet0) so we set that in the board definition, and use a defconfig for a single interface network.
...
SVN-Revision: 24442
2010-12-10 18:59:58 +00:00
b680f088ba
ar71xx: add support for the jjPlus JA79PF
...
Patch-by: Cezary Jackiewicz
SVN-Revision: 24440
2010-12-10 17:57:51 +00:00
5b0c83edd9
ar71xx: add support for the TP-LINK TL-MR3220 v1 board
...
SVN-Revision: 24439
2010-12-10 17:57:48 +00:00
83834da33b
ar71xx: add default network configuration file for the TL-MR3420
...
SVN-Revision: 24437
2010-12-10 17:57:40 +00:00
1fa3e7a941
ar71xx: do not throw compile errors if the nbg460n uboot is not selected
...
SVN-Revision: 24426
2010-12-10 16:07:27 +00:00
d9c68341ef
ar71xx: select u-boot for the NBG460N in the Default/Minimal profiles as well
...
SVN-Revision: 24421
2010-12-10 15:17:08 +00:00
081796fe47
ar71xx: add nbg460n image generation
...
This adds image generation for NBG460N/550N/550NH boards.
Signed-off-by: Michael Kurz <michi.kurz@googlemail.com>
SVN-Revision: 24419
2010-12-10 15:17:03 +00:00
ce0984ec5d
linux/generic: update & refresh 2.6.36 & 2.6.37. ( closes #8324 )
...
SVN-Revision: 24370
2010-12-08 21:20:40 +00:00
502dc1cb39
add optimization to Freescale targets
...
SVN-Revision: 24341
2010-12-08 11:27:06 +00:00
502d21dc2a
ramips: ramips_esw: add more definitions
...
SVN-Revision: 24340
2010-12-08 10:15:33 +00:00
bf58ef7c6d
ramips: ramips_esw: add helper function to set pvid
...
SVN-Revision: 24339
2010-12-08 10:15:28 +00:00
692d379b50
ramips: ramips_esw: add helper function to set vlan members
...
SVN-Revision: 24338
2010-12-08 10:15:25 +00:00
f7c3f91074
ramips: ramips_esw: add helper function to set VLAN id
...
SVN-Revision: 24337
2010-12-08 10:15:22 +00:00
0d2ad7a816
ramips: ramips_esw: introduce rt305x_esw_rmw{,_raw} function
...
SVN-Revision: 24336
2010-12-08 10:15:16 +00:00
7b878dde4b
ramips: ramips_esw: use rt305x_esw prefix in function names
...
SVN-Revision: 24335
2010-12-08 10:15:14 +00:00
0fcedc7bda
ramips: ramips_esw: coding style cleanup
...
SVN-Revision: 24334
2010-12-08 10:15:12 +00:00
48e6a31812
ramips: ramips_esw: add defines for switch register offsets
...
SVN-Revision: 24333
2010-12-08 10:15:07 +00:00
74c13f06df
ramips: ramips_esw: don't touch GPIO_PURPOSE register
...
It must have been set by the board initialization code.
SVN-Revision: 24332
2010-12-08 10:15:04 +00:00
3b9a6adc7d
ramips: ramips_esw: convert it to be a platform driver
...
SVN-Revision: 24331
2010-12-08 10:15:00 +00:00
889729df01
ramips: ramips_esw: move hardware initialization into a separate function
...
SVN-Revision: 24330
2010-12-08 10:14:58 +00:00
8957f39064
ramips: ramips_esw: use a private structure for the functions
...
SVN-Revision: 24329
2010-12-08 10:14:54 +00:00
f586bb26dd
ethernet driver fixup for ppc4xx
...
SVN-Revision: 24328
2010-12-08 08:59:31 +00:00
7224337d71
Profiles: GW6X00: Replace ext2 module with ext4 as ext2 and 3 are going away. Remove kmod-loop as the need for it has been superseded by block-extroot, and remove kmod-fs-vfat as it takes space and is rarely needed.
...
SVN-Revision: 24316
2010-12-08 00:40:31 +00:00
2a86dcc3d6
Profiles: Make buttons and led modules included by default so that failsafe will work in the case of builds for releases.
...
SVN-Revision: 24315
2010-12-08 00:40:28 +00:00
c6ef9a0720
Profiles: Move wpad-mini to the profiles that use it, rather than default for all profiles (because -wpad-mini means it's not selectable, which isn't what we always want for the No WiFi profile
...
SVN-Revision: 24314
2010-12-08 00:40:24 +00:00
4ab2416621
flash_chips: Added Macronix MX29LV640T Flash Chip support previously mistakenly added to brcm63xx. Thanks blunoise.
...
SVN-Revision: 24313
2010-12-07 19:45:08 +00:00
f8ed133c0a
patches: Renamed 150-led_count to 141-led_count so it comes before the 15-alice_gate2_leds.patch as which led count was mistakenly given the same number.
...
SVN-Revision: 24310
2010-12-07 17:32:29 +00:00
0e839ea40d
Revert "[brcm63xx] patches-2.6.35: Added flash chip definition for Macronix MX29LV640T."
...
This reverts commit 43511418ae2771a6662a83a254f06e37f4ac19e5.
It belongs in generic not brcm63xx.
SVN-Revision: 24308
2010-12-07 17:02:31 +00:00
183d628485
patches-2.6.35: Added flash chip definition for Macronix MX29LV640T. Thanks blunoise
...
SVN-Revision: 24307
2010-12-07 16:42:23 +00:00
8f9b14dafe
boards: Added GW6x00 fixups and GPIOs. The GW6200 GPIOs are different than the reference design 96348GW so we use fixup to allow us to define the correct ones, also the GW6000 has no GPIO-controlled leds.
...
SVN-Revision: 24305
2010-12-07 15:15:54 +00:00
3baa168e09
patches: Refreshed patches after led_count
...
SVN-Revision: 24304
2010-12-07 15:15:51 +00:00
b963cbde33
board definitions: Added patch for calculating led count, which was part of the patch removed in the previous commit
...
SVN-Revision: 24303
2010-12-07 15:15:47 +00:00
e5ca4d81f4
Remove patch 140-new_bcm96348gw_leds because it is really the GW6200 leds, not the generic 96348GW. Another commit will add the GW6200 specific boardid and leds. This removal reverts the 96348GW leds to the reference design GPIOs.
...
SVN-Revision: 24302
2010-12-07 15:15:41 +00:00
0fc35b30e3
kernel: fix cryptodev with kernel >= 2.6.35
...
The fix is from http://sourceforge.net/mailarchive/forum.php?thread_name=20100906035717.GA7562%40mcafee.com&forum_name=ocf-linux-users
Thank you tripolar for reporting the issue and finding a solution for it.
SVN-Revision: 24286
2010-12-06 17:01:10 +00:00
ad24e14b35
base-files: Added the preinit information for reset button and preinit indication led, and preinit interface
...
SVN-Revision: 24276
2010-12-06 06:46:03 +00:00
244db5ac6a
board definition: Fixed CPVA642 LED definitions
...
SVN-Revision: 24275
2010-12-06 06:45:57 +00:00
8316194016
board definitions: Added CPVA642 GPIO leds and buttons and refreshed patches later in series due to fuzz
...
SVN-Revision: 24274
2010-12-06 04:31:23 +00:00
7129521696
base-files: Added network defconfig because board only has one ethernet (4-port switch)
...
SVN-Revision: 24273
2010-12-06 02:01:08 +00:00
0449d92dd7
ramips: add support for 2.6.36
...
SVN-Revision: 24270
2010-12-05 20:14:38 +00:00
01a5cb48c8
ramips: default profile fix
...
Fix package names in default profiles.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 24269
2010-12-05 20:14:35 +00:00
47dd3b9fea
ramips: use tabs instead of spaces in mach-f5d8235-v2.c
...
SVN-Revision: 24268
2010-12-05 20:14:30 +00:00
2f7964de3e
brcm47xx: do not read from CFE
...
SVN-Revision: 24267
2010-12-05 19:20:26 +00:00
852f7b37ed
brcm47xx: backport patch from kernel 2.6.37
...
Backport patches from r24162
brcm47xx: reorder patches like they were commitet upstream
SVN-Revision: 24266
2010-12-05 19:19:50 +00:00
7b1ae48645
brcm47xx: use on common files dir
...
SVN-Revision: 24264
2010-12-05 18:34:58 +00:00
044ea01f9c
preliminary support for Freescale MPC85xx based boards
...
SVN-Revision: 24259
2010-12-05 11:38:59 +00:00
8067f3f3cc
ar71xx: work around a PCI controller bug which causes reads to the PCI_COMMAND register to return bogus values - properly fixes ath9k module reload issues
...
SVN-Revision: 24236
2010-12-04 01:32:15 +00:00
187359dc67
remove unused kernel versions, make 2.6.36 the default
...
SVN-Revision: 24223
2010-12-03 09:19:52 +00:00
41b3383499
brcm47xx: Add edimax PS1208mfg support
...
Thank you clemvangelis for the patches. (closes #7672 )
SVN-Revision: 24217
2010-12-02 21:27:54 +00:00
6f7e2d4ce8
tune rtl8366s default config, make vlan 1 cpu port tagged and use eth0.1 for the lan interface - this brings the configuration more in line with other switch setups
...
SVN-Revision: 24215
2010-12-02 20:19:55 +00:00
79c24b2cb0
ar71xx: refresh patches
...
SVN-Revision: 24210
2010-12-01 18:40:01 +00:00
17564e7db8
generic: yet another missing config symbol for 2.6.37
...
SVN-Revision: 24208
2010-12-01 18:39:55 +00:00
30b950154b
add a new image for the TEW-652BRP which can be used with the bootloader recovery option
...
SVN-Revision: 24196
2010-11-30 02:04:57 +00:00
2fe5c1d124
backport two changes from kernel.org: 65e9b62d4503849b10bedfc29bff0473760cc597 ipv6: add special mode accept_ra=2 to accept RA while configured as router
...
c3bccac2fa76f1619dfe4fb7b9bee69de7f066d8
ipv6: add special mode forwarding=2 to send RS while configured as router
SVN-Revision: 24195
2010-11-30 01:52:51 +00:00
9677b65cb6
image Makefile: Corrected router imagename length limiting. Thanks KanjiMonster for reminding me.
...
SVN-Revision: 24191
2010-11-28 22:13:00 +00:00
314bce63e6
bcm63xx: Add support for the T-Com Speedport W 500V.
...
Add support for the T-Com Speedport W 500V using a special tagged image as it
identifies itself as a 96348GW, but has some gpios wired differently, and also
has only one ethernet port without a switch attached to it.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 24190
2010-11-28 22:04:44 +00:00
3a49f669f2
bcm63xx: Add board id override fixup.
...
Add a fixup for the kernel to check the bcm tag of the image for a boardid in
the information1 field, and use that instead of the supplied one by cfe. This
is triggered by a + at the start of the information1 field.
Also modify the image generation to generate apropriately tagged images.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 24189
2010-11-28 22:04:40 +00:00
c51d772e62
bcm63xx: Finalize support for DSL-274xB, rev C2.
...
The DSL-2740B/DSL-2741B rev C2 support was missing the board definition,
resulting in a kernel panic on boot.
This patch adds it, and also renames the generated image name to properly
reflect that it is for the revision C2, and for both the DSL-2740B and
DSL-2741B.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 24188
2010-11-28 22:04:36 +00:00
8fa9b24a4c
bcm63xx: Allow 'colored' power leds.
...
Since some devices have more than one power led, they might be separated by
their color in the name. To also allow them to be on after leaving preinit,
set any status led starting with 'power' to on instead of only those with
the exact name of 'power'.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 24187
2010-11-28 22:04:30 +00:00
fec30c8c80
bcm63xx: Don't hardcode the switch ethernet interface in preinit.
...
Currently eth1 is hardcoded as the expected interface switches in diagmode.
This patch replaces the eth1 with the ifname, and also directly tests if
the interface specified by ifname has a switch attached.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 24186
2010-11-28 22:04:26 +00:00
b1b318750a
bcm63xx: Add defconfigs.
...
Port the mechanism for different default configurations from ar71xx and
use the old configuration as the default configuration. This should have
no functional differences to before.
While we are at it, remove the obsolete nat option.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 24185
2010-11-28 22:04:19 +00:00
a133b09b07
refresh patches and remove trailing whitespaces
...
SVN-Revision: 24181
2010-11-28 18:14:34 +00:00
27189b328e
refresh and refine 972-cpmac_multi_probe.patch, patch from sn9
...
SVN-Revision: 24180
2010-11-28 18:03:56 +00:00
629cc5b101
refresh 973-cpmac_handle_mvswitch.patch
...
SVN-Revision: 24179
2010-11-28 18:03:48 +00:00
a2aa5a227e
refresh and refine vlynq patch, patch from sn9
...
SVN-Revision: 24178
2010-11-28 18:03:42 +00:00
af2349b4bc
brcm47xx: remove support for old kernel versions
...
SVN-Revision: 24168
2010-11-28 14:08:04 +00:00
6f58cc20fc
brcm47xx: use kernel 2.6.36.1 as new default kernel for this target.
...
SVN-Revision: 24167
2010-11-28 14:05:31 +00:00
34d53c2be1
kernel: add missing config symbols for 2.6.37-rc3
...
Thank you maddes for reporting. (closes #8323 )
SVN-Revision: 24165
2010-11-28 11:14:25 +00:00
Felix Fietkau
Gabor Juhos
Hauke Mehrtens
Imre Kaloz
Alexandros C. Couloumbis
John Crispin
Hamish Guthrie
Jo-Philipp Wich
Daniel Dickinson
Florian Fainelli