57803a98ec
remove superfluous calls to /lib/brcm63xx.sh
...
The first preinit script 03_do_brcm63xx.sh does the right job of
exporting variables for the other subsequent preinit scripts to use
them.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35504
2013-02-05 22:25:30 +00:00
84d306d23c
remove references to the old switch driver
...
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35503
2013-02-05 22:25:19 +00:00
ec19a23bae
fix trx checksum after first boot and add led/button definitions for boards RTA770BW and RTA770W
...
SVN-Revision: 35501
2013-02-05 14:57:43 +00:00
f460388ce2
add support for board named RTA770W
...
Actually this board is the very same as the rta770bw,
where the additional 'b' within the name just
indicates 'Annex B'. The ADSL Modem itself is able
to handle both, Annex A as well as Annex B -
the loaded firmware makes the only difference
SVN-Revision: 35500
2013-02-05 14:57:40 +00:00
395d0bdc1f
generic: ar8216: clear driver specific data pointer in phy_device
...
This is needed to avoid a NULL pointer dereference:
[ 19.525270] Unable to handle kernel paging request for data at address 0x00000018
[ 19.532750] Faulting instruction address: 0xc016e104
[ 19.537714] Oops: Kernel access of bad area, sig: 11 [#1 ]
[ 19.543102] P1010 RDB
[ 19.545365] Modules linked in: booke_wdt nf_nat_irc nf_nat_ftp nf_conntrack_irc nf_conntrack_ftp ipt_MASQUERADE iptable_nat xt_nat d
[ 19.590725] NIP: c016e104 LR: c0171490 CTR: 00000000
[ 19.595681] REGS: c4bc3c10 TRAP: 0300 Tainted: G W O (3.7.6)
[ 19.602284] MSR: 00029000 <CE,EE,ME> CR: 82002022 XER: 20000000
[ 19.608381] DEAR: 00000018, ESR: 00000000
[ 19.612382] TASK = c4cd9c80[2070] 'ifconfig' THREAD: c4bc2000
GPR00: 00000001 c4bc3cc0 c4cd9c80 00000000 c7811000 00000000 00000000 0000e8ec
GPR08: 0000e8eb 00000000 00029000 00000001 00000000 100801f8 1005c51c 1005c514
GPR16: 1005c468 1005c54c 1005c258 1005c530 10060000 00000000 c7811000 ffff8914
GPR24: c7815030 c793e400 10063adb 00000000 c7811000 c045594c c78ca600 c7815000
[ 19.646352] NIP [c016e104] register_switch+0x98/0x2d0
[ 19.651397] LR [c0171490] ar8216_config_init+0x2d8/0x3f4
[ 19.656697] Call Trace:
[ 19.659138] [c4bc3cc0] [c0170490] ar8216_mii_read+0x64/0xc4 (unreliable)
[ 19.665835] [c4bc3d00] [c0171490] ar8216_config_init+0x2d8/0x3f4
[ 19.671835] [c4bc3d20] [c016cf8c] phy_init_hw+0x50/0x6c
[ 19.677053] [c4bc3d30] [c016d078] phy_attach_direct+0xd0/0xf8
[ 19.682793] [c4bc3d50] [c016d154] phy_connect_direct+0x24/0x68
[ 19.688621] [c4bc3d70] [c0183b70] of_phy_connect+0x48/0x6c
[ 19.694102] [c4bc3d90] [c0175aac] gfar_enet_open+0x254/0x3d8
[ 19.699755] [c4bc3db0] [c019acc4] __dev_open+0xc0/0x120
[ 19.704975] [c4bc3dd0] [c019af98] __dev_change_flags+0xd4/0x15c
[ 19.710888] [c4bc3df0] [c019b0d4] dev_change_flags+0x1c/0x60
[ 19.716544] [c4bc3e10] [c01ebb94] devinet_ioctl+0x290/0x690
[ 19.722111] [c4bc3e70] [c01ec8d4] inet_ioctl+0x88/0xbc
[ 19.727245] [c4bc3e80] [c0186b98] sock_ioctl+0x258/0x294
[ 19.732551] [c4bc3ea0] [c009c00c] do_vfs_ioctl+0x6a4/0x728
[ 19.738031] [c4bc3f10] [c009c0d4] sys_ioctl+0x44/0x70
[ 19.743077] [c4bc3f40] [c000c74c] ret_from_syscall+0x0/0x3c
[ 19.748646] --- Exception: c01 at 0x48091b34
[ 19.748646] LR = 0x480e4b64
[ 19.756033] Instruction dump:
[ 19.758991] 2f830000 907f0050 3860fff4 419e021c 837f0000 38000000 901f0038 901f0040
[ 19.766744] 901f003c 7f600034 5400d97e 0f000000 <801b0018> 2f800000 40be0010 801b001c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35497
2013-02-05 08:39:26 +00:00
2e7f38c243
generic: ar8216: unregister switch on error path
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35496
2013-02-05 08:39:24 +00:00
1bb8ad6050
mpc85xx: enable GPIO sysfs interface
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35495
2013-02-05 07:48:02 +00:00
6ba265a573
mpc85xx: enable Freescale eSPI driver and m25p80 support
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35494
2013-02-05 07:48:01 +00:00
eea43ffd33
mpc85xx: sync kernel config
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35493
2013-02-05 07:47:59 +00:00
8ba8225686
brcm47xx: fix detection of Asus RT-N16
...
This fixes #12936 .
SVN-Revision: 35492
2013-02-04 22:49:05 +00:00
a1e3c0ca46
Add Failsafe support for Linksys E3000V1 / WRT610NV2
...
Adds specification of the correct cpu_port for Linksys E3000V1 and WRT610NV2
in /lib/preinit/05_init_interfaces_brcm. The list of devices will need to
be expanded. Is there a way to determine the correct cpu_port to use in a
generic sense; for instance, if "/proc/switch/eth0/port/8" exists, or if
"/sys/class/net/eth0/device/driver/module/drivers/bcma:bgmac" exists? Could
a similar method be used in "/etc/init.d/netconfig"?
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 35491
2013-02-04 22:40:57 +00:00
c2198aba32
brcm47xx: Fix switch config on 4716/53115 devices
...
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
SVN-Revision: 35490
2013-02-04 22:38:37 +00:00
b97aee1ee8
coldfire: R.I.P.
...
The target still uses 2.6.38. The support of that
kernel version has been removed ~9 months ago.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35489
2013-02-04 15:23:10 +00:00
c41002971a
leon: R.I.P.
...
It is broken since ~9 months and nobody takes care of that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35488
2013-02-04 15:23:08 +00:00
539e0b5b84
imx21: R.I.P.
...
It is broken since ~22 months and nobody takes care of that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35487
2013-02-04 15:23:07 +00:00
e7dee4ea87
octeon: R.I.P.
...
It is broken since ~8 months and nobody takes care of that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35486
2013-02-04 15:23:05 +00:00
da44b916cf
omap35xx: R.I.P.
...
It is broken since ~22 months and nobody takes care of that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35485
2013-02-04 15:23:04 +00:00
8506964e6d
bcm63xx: add support for linux 3.8
...
Based on 3.8-rc6
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35482
2013-02-04 10:19:55 +00:00
3b4fced67d
bcm63xx: add support for linux 3.7
...
Based on 3.7.6.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35481
2013-02-04 10:19:50 +00:00
0e9365b346
kernel: generic: update the ehci overcurrent patch to upstream submission
...
Adds support for setting this in the generic platform driver's platform_data.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35480
2013-02-04 10:19:37 +00:00
e0fe5596f8
kernel: generic: add back the patch exporting bcm63xx tag header
...
It went missing when adding linux 3.7 support.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35479
2013-02-04 10:19:35 +00:00
34ad8f4e75
kernel: generic: update to 3.8-rc6
...
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35478
2013-02-04 10:19:28 +00:00
a15e1a950d
bcm63xx: refresh 3.6 patches
...
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35477
2013-02-04 10:19:24 +00:00
08ff976720
kernel: update linux 3.7 to 3.7.6
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35476
2013-02-04 10:02:56 +00:00
b1168e70d3
ar71xx: use backported PCI_MEM_SIZE patches
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35470
2013-02-02 18:17:58 +00:00
b9b341f05a
ar71xx: rename ar933x_uart patch
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35469
2013-02-02 18:17:53 +00:00
9ed81a91f3
ramips: build image for the Omnima EMB HPM board
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35468
2013-02-02 17:21:06 +00:00
813aec6796
ramips: add user-space support for the Omnima EMB HPM board
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35467
2013-02-02 17:21:05 +00:00
d578f3ac38
ramips: rt3883: add kernel support for the Omnima EMB HPM board
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35466
2013-02-02 17:21:01 +00:00
b99b2ff553
ramips: add userspace support for the Edimax BR-6425
...
[juhosg: remove sysupgrade changes]
Signed-off-by: Yuval Adam <yuv.adm@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35463
2013-02-02 17:01:50 +00:00
0a42e38bad
ramips: add kernel support for the Edimax BR-6425 board
...
Signed-off-by: Yuval Adam <yuv.adm@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35462
2013-02-02 17:01:47 +00:00
4ac6eb480b
x86/kvm_guest: add support for 3.7
...
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35460
2013-02-02 15:31:57 +00:00
c340ef2ae2
x86: add missing symbols for 3.7
...
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35459
2013-02-02 15:31:55 +00:00
0f46f47512
x86/kvm_guest: add missing symbols for 3.3
...
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35458
2013-02-02 15:31:54 +00:00
ab3e3cacaa
alix2: convert from kernel version 3.3.8 to 3.7.5
...
[juhosg: use 3.7.5 instead of 3.7.3]
Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35457
2013-02-02 15:31:52 +00:00
4c223d7d4f
generic: convert crypto-ocf from kernel_thread to kthread
...
recent kernels have finally stopped exporting kernel_thread, since a
deprecation circa 2006. This patch attempts to convert to the newer
kernel kthread API, particularly in random.c
[juhosg: remove randomproc variable, it is not required after the patch]
Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35456
2013-02-02 15:31:44 +00:00
7c87d28054
ar71xx: fixes whitespaces for dir-825-c1
...
Signed-off-by: Alexander Stadler <sa.maillists@univie.ac.at>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35455
2013-02-02 15:02:19 +00:00
ecf55822bb
mpc85xx: nuke 3.6 support
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35453
2013-02-02 10:05:43 +00:00
242859abae
mpc85xx: switch to 3.7
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35452
2013-02-02 10:05:40 +00:00
cde71c305c
mpc85xx: add support for linux 3.7
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35451
2013-02-02 10:05:37 +00:00
bbfd8cbf94
linux/3.7: add missing config symbols
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35450
2013-02-02 10:05:08 +00:00
9a438b2271
ar71xx: build images for the TP-LINK TL-WR743ND v2
...
AR9331 based, these same as 741v4
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35449
2013-02-02 10:01:15 +00:00
668e529220
generic: fix gc_sections patch
...
Due to the patch, essential '.data..*' sections are merged
into the '.data' section:
--- vmlinux.good.sect 2013-02-01 23:49:16.000000000 +0100
+++ vmlinux.bad.sect 2013-02-01 23:49:02.000000000 +0100
@@ -1,5 +1,5 @@
-vmlinux.good: file format elf32-powerpc
+vmlinux.bad: file format elf32-powerpc
Sections:
Idx Name Size VMA LMA File off Algn
@@ -53,43 +53,35 @@
CONTENTS, ALLOC, LOAD, READONLY, DATA
24 .machine.desc 00000460 c04e1000 004e1000 004f1000 2**2
CONTENTS, ALLOC, LOAD, DATA
- 25 .data 0000f6a0 c04e2000 004e2000 004f2000 2**12
+ 25 .data 0001635c c04e2000 004e2000 004f2000 2**12
CONTENTS, ALLOC, LOAD, DATA
- 26 .data..init_task 00002000 c04f2000 004f2000 00502000 2**3
- CONTENTS, ALLOC, LOAD, DATA
- 27 .data..page_aligned 00002000 c04f4000 004f4000 00504000 2**12
- CONTENTS, ALLOC, LOAD, DATA
- 28 .data..cacheline_aligned 00000c00 c04f6000 004f6000 00506000
2**5
- CONTENTS, ALLOC, LOAD, DATA
- 29 .data..read_mostly 000015e0 c04f6c00 004f6c00 00506c00 2**3
- CONTENTS, ALLOC, LOAD, DATA
- 30 .sbss 000002e0 c04f9000 004f9000 005081e0 2**3
+ 26 .sbss 000002e0 c04fa000 004fa000 0050835c 2**3
<...>
This causes boot hang on powerpc. Modify the patch to
ensure that the kernel specific '.data..*' sections
remain separate.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35447
2013-02-02 09:30:47 +00:00
31af0dc186
ar71xx: fix mac address calculation on the OpenMesh MR600
...
Signed-off-by: Marek Lindner <marek@open-mesh.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35446
2013-02-02 08:47:41 +00:00
257b21f2d4
mpc85xx: nuke 3.3 support
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35445
2013-02-01 17:49:56 +00:00
cf2faab4ae
mpc85xx: switch to 3.6
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35444
2013-02-01 17:49:54 +00:00
56849d146c
mpc85xx: add support for 3.6
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35443
2013-02-01 17:49:53 +00:00
630fffbead
mpc85xx: fix dts name for P1010RDB
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35442
2013-02-01 17:49:52 +00:00
a2529eab2b
linux/3.6: add missing config symbols
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35441
2013-02-01 17:30:18 +00:00
fb936218a1
linux/3.6: refresh patches
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35440
2013-02-01 17:30:15 +00:00
495820f7a0
mpc85xx: remove broken flag
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35439
2013-02-01 17:28:54 +00:00
4cb7e749ab
mpc85xx: build fdt file for the PB1010RDB board
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35438
2013-02-01 17:28:51 +00:00
20ca35570e
mpc85xx: enable PB1010RDB support
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35437
2013-02-01 17:28:49 +00:00
21b15ddda5
mpc85xx: image: fix building of multiple dtb files
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35436
2013-02-01 17:28:47 +00:00
d158dfc607
linux/3.3: disable crashlog on PPC
...
It causes NULL pointer dereference:
[ 0.638235] __ioremap(): phys addr 0x7f00000 is RAM lr c025d61c
[ 0.644090] Unable to handle kernel paging request for data at address 0x00000000
[ 0.651533] Faulting instruction address: 0xc025d620
[ 0.656483] Oops: Kernel access of bad area, sig: 11 [#1 ]
[ 0.661856] P1010 RDB
[ 0.664113] Modules linked in:
[ 0.667152] NIP: c025d620 LR: c025d61c CTR: c000dc38
[ 0.672101] REGS: c7831ef0 TRAP: 0300 Not tainted (3.3.8)
[ 0.677740] MSR: 00029000 <CE,EE,ME> CR: 42022082 XER: 20000000
[ 0.683817] DEAR: 00000000, ESR: 00000000
[ 0.687811] TASK = c782c000[1] 'swapper' THREAD: c7830000
[ 0.693017] GPR00: a1ee0000 c7831fa0 c782c000 00000000 0000214c ffffffff c7831ea6 0001ffff
[ 0.701350] GPR08: c03697cc c035fba0 c03697cc c0360000 42022022 00000000 00000000 00000000
[ 0.709682] GPR16: c0000a00 00000014 3fffffff 00ffa000 00000015 07fc42bc c0360000 00000000
[ 0.718015] GPR24: 00000000 00000000 00001680 c0360000 00000000 c025d5e8 c0390000 c038b824
[ 0.726535] NIP [c025d620] crashlog_init_fs+0x38/0xd8
[ 0.731560] LR [c025d61c] crashlog_init_fs+0x34/0xd8
[ 0.736503] Call Trace:
[ 0.738939] [c7831fa0] [c025d61c] crashlog_init_fs+0x34/0xd8 (unreliable)
[ 0.745712] [c7831fb0] [c0001e98] do_one_initcall+0xd4/0x198
[ 0.751357] [c7831fe0] [c02537f4] kernel_init+0x9c/0x120
[ 0.756647] [c7831ff0] [c000c2dc] kernel_thread+0x4c/0x68
[ 0.762022] Instruction dump:
[ 0.764975] 3860fff4 bfc10008 3fc0c039 90010014 3bfeb824 801f0004 2f800000 41be00a0
[ 0.772699] 7c030378 38804000 4bdb38cd 3c00a1ee <81630000> 6000dead 7c691b78 907eb824
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35435
2013-02-01 17:28:44 +00:00
fb2e2a56d7
refresh kernel configs
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35434
2013-02-01 17:28:40 +00:00
6805275fdc
ar71xx: sysupgrade - fix OpenMesh MR600 total flash size
...
Signed-off-by: Marek Lindner <marek@open-mesh.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35433
2013-02-01 15:50:54 +00:00
979676ffcc
ar71xx: add sysupgrade support for OpenMesh MR600v2
...
Signed-off-by: Marek Lindner <marek@open-mesh.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35430
2013-02-01 15:50:47 +00:00
2af995ba1d
ar71xx: add user-space support for OpenMesh MR600v2
...
Signed-off-by: Marek Lindner <marek@open-mesh.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35429
2013-02-01 15:50:45 +00:00
8837d3a49b
ar71xx: add kernel support for the OpenMesh MR600v2
...
Signed-off-by: Marek Lindner <marek@open-mesh.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35428
2013-02-01 15:50:42 +00:00
150bb9d0b1
ar71xx: remove unused OpenMesh MR600 led definitions
...
Signed-off-by: Marek Lindner <marek@open-mesh.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35427
2013-02-01 15:50:39 +00:00
fe3db74276
ar71xx: remove unused OpenMesh MR6000 platform code
...
Signed-off-by: Marek Lindner <marek@open-mesh.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35426
2013-02-01 15:50:37 +00:00
492cbcdd6b
ar71xx: build image for the TL-WDR3500 board
...
Based on http://patchwork.openwrt.org/patch/3208/
Thanks-to: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Gui Iribarren <gui@altermundi.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35425
2013-02-01 15:50:34 +00:00
119dc460a3
ar71xx: add user-space support for TL-WDR3500 board
...
Based on http://patchwork.openwrt.org/patch/3208/
Thanks-to: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Gui Iribarren <gui@altermundi.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35424
2013-02-01 15:50:32 +00:00
5bd02ca895
ar71xx: add kernel support for the TL-WDR3500 board
...
WDR3500 is similar to WDR3600 except it doesn't have gigabit ethernet,
and has only 1 USB port.
Pending issues:
* Leds are not working at all (except power and wlan_5g)
* LAN switch ethernet ports are reversed with respect to case label.
[Label] -> soft device
[LAN1] -> eth0.4
[LAN2] -> eth0.3
[LAN3] -> eth0.2
[LAN4] -> eth0.1
Based on http://patchwork.openwrt.org/patch/3208/
Thanks-to: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Gui Iribarren <gui@altermundi.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35423
2013-02-01 15:50:29 +00:00
ce8b226046
bcm63xx: replace kmod-switch with swconfig in default package set
...
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35407
2013-01-30 00:19:21 +00:00
f7ff677169
ar71xx: add profile and build image for dir-825-c1
...
Signed-off-by: Alexander Stadler <sa.maillists@univie.ac.at>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35403
2013-01-29 22:50:57 +00:00
2a5193308f
ar71xx: add user space support for dir-825-c1
...
[juhosg: fix whitespaces in some scripts]
Signed-off-by: Alexander Stadler <sa.maillists@univie.ac.at>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35402
2013-01-29 22:50:54 +00:00
800da21cb1
ar71xx: add kernel support for dir-825-c1
...
[juhosg:
- remove unused GPIO stuff
- use a separate kernel patch for machine integration]
Signed-off-by: Alexander Stadler <sa.maillists@univie.ac.at>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35401
2013-01-29 22:50:50 +00:00
5a2aa8f184
generic: fix default compression selection in ubifs
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35398
2013-01-29 21:32:22 +00:00
da9a704e92
ar71xx: add profile and generate images for the AP132 board
...
Based on http://patchwork.openwrt.org/patch/3162/
Signed-off-by: Embedded Wireless GmbH <info at embeddedwireless.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35397
2013-01-29 19:12:34 +00:00
5d4ddbce72
ar71xx: add user-space support for the AP132 board
...
Based on http://patchwork.openwrt.org/patch/3162/
Signed-off-by: Embedded Wireless GmbH <info at embeddedwireless.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35396
2013-01-29 19:12:32 +00:00
5ca187570f
ar71xx: add kernel support for Atheros AP132 Reference Board
...
Based on http://patchwork.openwrt.org/patch/3162/
Signed-off-by: Embedded Wireless GmbH <info at embeddedwireless.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35395
2013-01-29 19:12:30 +00:00
8a9d92f125
ar71xx: fix ethernet device registration for the QCA9556 SoC
...
Based on http://patchwork.openwrt.org/patch/3162/
Signed-off-by: Embedded Wireless GmbH <info at embeddedwireless.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35394
2013-01-29 19:12:28 +00:00
e9dbff1193
ar71xx: add kernel support for the QCA9556 SoC
...
Based on http://patchwork.openwrt.org/patch/3162/
Signed-off-by: Embedded Wireless GmbH <info at embeddedwireless.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35393
2013-01-29 19:12:26 +00:00
df15e5cd61
ar71xx: enable fast flash read on dual-flash devices
...
This improves flash read speed on various Buffalo units.
mtd_speedtest results on the WZR-HP-AG300H:
old new delta
eraseblock read speed: 726 KiB/s 2068 KiB/s +184.85%
page read speed: 699 KiB/s 1973 KiB/s +182.26%
2 page read speed: 711 KiB/s 2043 KiB/s +187.34%
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35392
2013-01-29 19:12:25 +00:00
562ba537fc
kernel: update linux 3.7 to 3.7.5
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35390
2013-01-29 18:29:45 +00:00
c6744513a3
fix mtd_mp25p80_add_gd25q32_gd25q64.patch
...
SVN-Revision: 35378
2013-01-29 11:06:57 +00:00
714b2cfef3
Fix GigaDevice GD25Q32/GD25Q64 SPI Flash bad commit
...
Fix GigaDevice GD25Q32/GD25Q64 SPI Flash bad commit.
The patch was added to "linux/generic/patches-3.6" instead of
"target/linux/generic/patches-3.6".
I also fixed a missing patch space and refreshed generic patches.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35367
2013-01-29 09:46:11 +00:00
e252a1492c
generic: fix build failure in MIPS kexec code if SMP is enabled
...
Fix it for older kernels as well.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35366
2013-01-29 09:44:58 +00:00
22ce389e6a
ar71xx: add TP-LINK WA-801ND to run-time model detection
...
A small cosmetic fix to show the HW model name correctly in LuCI.
Patch-by: Amir Sagie <openwrt-devel@taproot.org.il>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35365
2013-01-29 09:40:29 +00:00
1b3c6ad1fb
generic: fix build failure in MIPS kexec code if SMP is enabled
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35364
2013-01-29 09:40:23 +00:00
756a7c5451
fix for non-blinking LAN LEDs
...
https://dev.openwrt.org/ticket/12830
SVN-Revision: 35359
2013-01-28 18:06:31 +00:00
a0f7a3c214
dont load gptu on ase
...
fixes #12792
SVN-Revision: 35357
2013-01-28 17:46:07 +00:00
d93706154b
ramips: reset switch on single-port devices
...
Signed-off-by: Daniel Gole <dgolle@allnet.de>
SVN-Revision: 35356
2013-01-28 17:44:41 +00:00
0de0955931
refresh patches
...
SVN-Revision: 35355
2013-01-28 17:44:20 +00:00
0183df8ed9
Fix ARV7518 USB
...
This patch correctly fixes USB on Lantiq ARV7518.
There was a failed attempt on fixing this on r35077 (https://dev.openwrt.org/changeset/35077/ ).
Signed-off-by: José Vázquez Fernández <ppvazquezfer@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 35354
2013-01-28 17:43:35 +00:00
3534757bb9
Add ath9k eeprom and pci fixup support
...
Add ath9k eeprom and pci fixup support (again) for linux 3.7.
On linux 3.3, the fixup forced the regdomain to 0x67, causing low TX power.
This patch only corrects checksum, the rest of the EEPROM isn't changed.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 35353
2013-01-28 17:43:25 +00:00
5eb43d4cf8
Add support for ARV4518PW R01 and rename R01A.
...
There are two different versions of SMC7908A-ISP: R01 and R01A.
R01 has an internal clock for PCI, meanwhile R01A has an external clock.
This fixes: https://dev.openwrt.org/ticket/12884
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 35352
2013-01-28 17:42:59 +00:00
1dc9c8ef69
kernel: disable CONFIG_CRYPTO_MANAGER2, it is not needed
...
SVN-Revision: 35342
2013-01-27 23:23:39 +00:00
68aeb7af8e
brcm47xx: load pps_core and ptp before tg3 to make the interface available for failsafe.
...
SVN-Revision: 35341
2013-01-27 21:48:28 +00:00
a9175c90cf
kernel: b53: the b53 spi driver depends on spi
...
SVN-Revision: 35340
2013-01-27 21:39:53 +00:00
62554217fc
kernel: add packages for pps and ptp, they are needed by tg3 in kernel 3.8
...
SVN-Revision: 35336
2013-01-27 21:18:52 +00:00
8193bbe59a
netfilter: add support for flushing conntrack via /proc
...
SVN-Revision: 35330
2013-01-27 19:02:38 +00:00
156a6e7999
kernel: clean up crypto kconfig options on 3.8
...
SVN-Revision: 35329
2013-01-27 17:49:09 +00:00
721bf97863
kernel: remove __devinit, __devexit and __devexit_p for kernel 3.8
...
These attributes where removed with kernel 3.8 and are now causing compile errors.
SVN-Revision: 35328
2013-01-27 17:48:48 +00:00
ed7ca5d44e
kernel: clean up crypto related kconfig options
...
SVN-Revision: 35327
2013-01-27 17:23:12 +00:00
8a1091ad53
ar71xx: disable support for unsupported mtd configuration, saves about 5K kernel size after lzma
...
SVN-Revision: 35326
2013-01-27 16:38:27 +00:00
044c316167
kernel: prevent cryptomgr from pulling in useless extra dependencies for tests that are not run
...
Reduces kernel size after LZMA by about 5k on MIPS
SVN-Revision: 35325
2013-01-27 16:21:08 +00:00
e083c7926b
brcm47xx: create image for Netgear WNDR3400 V1
...
SVN-Revision: 35323
2013-01-26 20:34:38 +00:00
05623aebef
brcm47xx: add initial board detection code
...
SVN-Revision: 35322
2013-01-26 20:34:00 +00:00
a83d7bb109
brcm47xx: add gpio to irq function again
...
SVN-Revision: 35321
2013-01-26 20:33:23 +00:00
8933b918cd
kernel: use -ffunction-sections, -fdata-sections and --gc-sections on mips
...
in combination with kernel symbol export stripping this significantly reduces
the kernel image size
SVN-Revision: 35320
2013-01-26 16:26:13 +00:00
15be1c9ee7
kernel: update linux 3.7 to 3.7.4
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35318
2013-01-24 17:08:37 +00:00
680f460861
kernel: refresh 3.8 patches
...
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35317
2013-01-24 17:04:52 +00:00
9781461a3d
mvebu: update to 3.8-rc4
...
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35316
2013-01-24 17:04:46 +00:00
4a69e20a10
kernel: add missing config options for 3.8
...
SVN-Revision: 35315
2013-01-24 14:48:15 +00:00
76c12ff797
brcm47xx: change generic profiles
...
The default profile now contains Ethernet drivers for all the types
found on supported boards. There are other profiles for each Ethernet
driver.
SVN-Revision: 35314
2013-01-24 14:38:10 +00:00
b60fc82ce5
kernel: remove the cisco sip phone patch for 3.7 and 3.8 as well
...
SVN-Revision: 35310
2013-01-23 16:31:38 +00:00
8ce8960959
ar71xx: sync kernel sizes where possible to fix images for some devices ( #12874 )
...
SVN-Revision: 35309
2013-01-23 16:29:25 +00:00
8411e5c06e
bcm63xx: switch to b53 and swconfig
...
Switch to using the B53 switch driver where appropriate.
Use a non-tagged default config where it isn't confirmed to be
working.
Remove the switch configuration in preinit as the switch will now
be configured by the driver to use port isolation to prevent leakage
between lan and wan.
While at it, also provide a switch config for Neufbox 6.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35307
2013-01-23 10:12:40 +00:00
17d51121a6
bcm63xx: expose the internal switch to b53
...
Allow b53 access to the internal switch of BCM6328, BCM6362 and BCM6368.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35306
2013-01-23 10:12:37 +00:00
bb0118c66f
generic: add b53 swconfig switch driver
...
Add swconfig switch driver for Broadcom BCM53XX switch chips. Supports
switches connected through MDIO, SPI or memory mapped registers, and
supports BCM5325, BCM539x, BCM531x5 and the BCM63XX internal switch
chips.
Tested are BCM5325 trough MDIO, BCM53115 through SPI, and BCM6328.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35305
2013-01-23 10:12:33 +00:00
3e998d9cf9
bcm63xx: move bcm63xx-spi into the kernel
...
The SPI driver is needed for supporting to boot from SPI flash on BCM6358
and BCM6368, and for SPI connected switches.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35304
2013-01-23 10:12:13 +00:00
46e4246d61
kernel: remove 340-module_alloc_size_check.patch from linux 3.8, it is not necessary anymore
...
SVN-Revision: 35248
2013-01-19 19:14:37 +00:00
ed6d399f8d
ramips: add profile and build image for the Tenda 3G300M
...
Factory image should be used to flash from
original firmware.
[juhosg: use the GENERIC_4M template]
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35246
2013-01-19 17:05:07 +00:00
9891603eb5
ramips: add user-space support for the Tenda 3G300M
...
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35245
2013-01-19 17:05:06 +00:00
7eff5d2df0
ramips: add kernel support for the Tenda 3G300M
...
Ralink RT3052F, 4MB flash, 32MB ram, one USB 2.0, two buttons
and seven leds.
Factory image should be used to flash from original firmware.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35244
2013-01-19 17:05:03 +00:00
f7a943694f
ramips: use MkImage for Hauppauge Broadway, Netcore NW718 and Tenda W306R V2.0
...
These targets need custom image names specified in the uImage header.
MkImage accepts an optional 4th argument to do exactly that. Reuse the
facility to generate factory images.
Compile-tested, the generated files inspected with "file" utility.
[juhosg:
- keep the factory.bin images to avoid users confusion,
- use GENERIC_4M template for the W306R V2.0
- update commit log]
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35243
2013-01-19 15:36:13 +00:00
6aebe6a65d
ramips: allow to override image name/suffix in GENERIC_{4,8}M macros
...
Sysupgrade/KRuImage and BuildFirmware/Generic macros
are changed as well.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35242
2013-01-19 15:36:11 +00:00
60dde219d4
ramips: do not stop the build if some targets fail
...
This becomes crucial when you are using a generic profile to build an image
larger than 4M, e.g. for w502u.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35238
2013-01-19 08:51:45 +00:00
c3eeff807f
generic: rtl8366_smi: only assign pvid if no pvid was set yet
...
Only assign a pvid if the current pvid is 0. Fixes using mixed tagged
and untagged traffic on a port and the untagged vlan isn't the last one
of which the port is a member.
Tested on RTL8366S and RTL8367R.
Fixes #8501 .
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35227
2013-01-18 15:19:11 +00:00
3a2cccda2e
all targets: use numerically prefixed uci-defaults file names to better control order of execution
...
SVN-Revision: 35217
2013-01-18 12:42:53 +00:00
0de21d9747
kernel: update linux 3.7 to 3.7.3
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35216
2013-01-18 11:44:42 +00:00
c8215775f3
mvebu: enable PCI in kernel configuration
...
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35214
2013-01-17 22:29:26 +00:00
5e45a4344c
mvebu: enable PCIe on Marvell Armada 370 Reference Design
...
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35213
2013-01-17 22:29:22 +00:00
cf9343ac86
mvebu: enable USB on Armada 370 Reference Design
...
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35212
2013-01-17 22:29:18 +00:00
7e1e7063c2
mvebu: add preliminary support for PCI express
...
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35211
2013-01-17 22:29:13 +00:00
29c21b973b
mvebu: refresh patches
...
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35210
2013-01-17 22:28:58 +00:00
28acc6588d
kernel: refresh 3.8 patches
...
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35209
2013-01-17 22:28:53 +00:00
a286a55c6f
mvebu: add board detection scripts
...
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35208
2013-01-17 22:28:48 +00:00
f7858466e2
mvebu: enable /proc/devicetree usage
...
This is going to be used for proper user-space board identification (ala
mcs814x).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35207
2013-01-17 22:28:37 +00:00
15b4681e3e
mvebu: add default profile
...
Such that relevant kernel modules are selected (USB, I2C, SATA, RTC,
SDIO)
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35206
2013-01-17 22:28:33 +00:00
7399df1d69
x86: explicitely pass staging directory to grub-mkimage instead of relying on build time defaults ( #12821 )
...
SVN-Revision: 35200
2013-01-17 15:46:26 +00:00
57f7408b8a
generic: add EHCI|OHCI platform driver fix to 3.[36]
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35194
2013-01-17 13:54:14 +00:00
576aa2af0c
ramips: enable BR6425N in kernel config
...
Though originally contained in the patch applied in r35020, the move to 3.7 in
r34845 lost the kernel .config option. Reintroduce it to config-3.7.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 35191
2013-01-17 09:39:44 +00:00
05466923b8
mvebu: add support for EHCI controller
...
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35181
2013-01-15 19:55:50 +00:00
c53a347034
mvebu: add support for the Marvell Armada 370 Reference Design board
...
Keep the patches in sync with the upstream developments.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35179
2013-01-15 19:55:40 +00:00
58f8c5d87a
mvebu: enable SMP with SMP on UP enabled
...
The same kernel works ok for both Armada 370 (UP) and Armada XP (SMP)
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35178
2013-01-15 19:55:31 +00:00
fa1afc1fa9
mvebu: add support for RTC
...
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35176
2013-01-15 19:55:19 +00:00
b3b04e9fb1
kernel: port 203-kallsyms_uncompressed.patch and 305-mips_module_reloc.patch to 3.8
...
SVN-Revision: 35162
2013-01-14 18:55:36 +00:00
78dc69e1d4
generic: remove EHCI platform driver fix from 3.8
...
It is not needed on 3.8.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35160
2013-01-14 17:53:55 +00:00
b035c594ae
generic: add EHCI|OHCI platform driver fix from the cns21xx target
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35159
2013-01-14 17:47:23 +00:00
1e103b2ecc
target: enable XZ BCJ decompressor code after r35097
...
Required to actually be able to mount squashfs xz compressed
filesystems.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35156
2013-01-14 16:34:25 +00:00
e0e3509b5c
kernel: add a config option for keeping the kallsyms table uncompressed, saving ~9kb kernel size after lzma on ar71xx
...
SVN-Revision: 35154
2013-01-14 16:08:18 +00:00
1474359bd3
ar71xx: fix unaligned access in cls_u32
...
SVN-Revision: 35132
2013-01-13 16:48:23 +00:00
e67b6ee395
ar71xx: fix unaligned access in a few more places
...
SVN-Revision: 35130
2013-01-13 15:37:58 +00:00
b5bcbdfbb5
ar71xx: improve unaligned access patches, add a net_hdr_word() macro which assumes 2-byte aligned access and generates better code than {get,put}_unaligned_cpu32
...
SVN-Revision: 35129
2013-01-13 14:54:39 +00:00
53e0ba49b9
ar71xx: avoid __packed define in the unaligned access hack patch, make the ipv6 address struct also 2-byte-aligned/packed
...
SVN-Revision: 35127
2013-01-13 13:06:09 +00:00
5d55cece6e
kernel: add back the mips module relocation patch
...
SVN-Revision: 35126
2013-01-13 12:23:42 +00:00
764520975c
ar71xx: add more cpu feature overrides, slightly reduces kernel size
...
SVN-Revision: 35125
2013-01-13 11:33:48 +00:00
310724c14d
ar71xx: extend the unaligned access hacks to a few more places that showed up in the new kernel
...
SVN-Revision: 35124
2013-01-13 11:33:44 +00:00
2bf03f971d
brcm47xx: BCMA - Update default IRQ assignment per upstream change
...
Update the default IRQ assignment for unrecognized devices per
the upstream change.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 35121
2013-01-12 15:00:01 +00:00
5d1ecfc26d
refresh kernel configs with kconfig.pl
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35119
2013-01-12 12:29:55 +00:00
ef75e6c71a
malta: remove 3.6 support
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35118
2013-01-12 12:29:53 +00:00
3d057de4db
malta: build lzma and gzip compressed uImages
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35117
2013-01-12 12:29:52 +00:00
df8a8f2515
adm5120: remove 3.6 support
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35116
2013-01-12 12:25:42 +00:00
d472567997
adm5120: switch to 3.7
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35115
2013-01-12 12:25:40 +00:00
eb2188c0e2
ar71xx: remove 3.6 support
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35114
2013-01-12 12:25:38 +00:00
fe86bc9370
ar71xx: switch to 3.7
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35113
2013-01-12 12:25:36 +00:00
ca882f230d
mpc83xx: remove 3.6 support
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35112
2013-01-12 12:25:34 +00:00
eba037cd1f
mpc83xx: switch to 3.7
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35111
2013-01-12 12:25:32 +00:00
ff2ce330a5
ramips: remove 3.6 support
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35110
2013-01-12 12:25:30 +00:00
d53f8c3ded
ramips: switch to 3.7
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35109
2013-01-12 12:25:28 +00:00
f8f009ca43
rb532: remove 3.6 support
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35108
2013-01-12 12:25:26 +00:00
cd71dcdab7
rb532: switch to 3.7
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35107
2013-01-12 12:25:24 +00:00
7098354885
ppc44x: remove 3.6 support
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35106
2013-01-12 12:25:21 +00:00
83fccacec2
ppc44x: switch to 3.7
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35105
2013-01-12 12:25:20 +00:00
9d3bae8f0e
ppc40x: remove 3.6 support
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35104
2013-01-12 12:25:18 +00:00
06fea75afb
ppc40x: switch to 3.7
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35103
2013-01-12 12:25:16 +00:00
a51f602494
cns21xx: remove 3.6 support
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35102
2013-01-12 12:25:14 +00:00
bdc6ec4974
cns21xx: switch to 3.7
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35101
2013-01-12 12:25:12 +00:00
c19c30cefd
kernel: update linux 3.7 to 3.7.2
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35100
2013-01-12 11:43:08 +00:00
ecf230710f
mvebu: update to 3.8-rc3
...
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35086
2013-01-10 17:20:25 +00:00
548cb59826
brcm47xx: update bgmac driver to the version in mainline kernel
...
SVN-Revision: 35083
2013-01-10 14:22:19 +00:00
885eea1842
kernel: update bcma and ssb to master-2013-01-09 from wireless-testing
...
SVN-Revision: 35080
2013-01-10 14:05:18 +00:00
a2950fabd4
clean up PCI bus topology
...
This makes the PCI bus topology more standard for devices behind a bridge
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 35079
2013-01-10 13:25:12 +00:00
b63b970866
clean up PCI bus topology
...
This makes the PCI bus topology more standard for devices behind a bridge
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 35078
2013-01-10 13:23:33 +00:00
64910f4490
fixes USB reset on ARV7518
...
SVN-Revision: 35077
2013-01-10 06:44:58 +00:00
4834d09a3f
fixes none-pci build
...
SVN-Revision: 35062
2013-01-09 09:04:09 +00:00
25475a095e
mvebu: add inital support for Marvell Armada XP/370 SoCs
...
This brings in the initial support for the Marvell Armada XP/370 SoCs.
Successfully tested on RD-A370-A1 and DB-MV784MP-GP boards the following
interfaces:
- Ethernet
- SDIO
- GPIOs
- SATA
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35058
2013-01-08 22:20:16 +00:00
97acd10458
add support for 3.8 kernel
...
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35057
2013-01-08 22:20:11 +00:00
9b601b79d0
add support for 3.8 kernel
...
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35056
2013-01-08 22:20:06 +00:00
8dbed04ec9
kernel: add support for 3.8-rc2
...
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35055
2013-01-08 22:19:31 +00:00
7b0af8193b
brcm47xx: BGMAC Driver corrections
...
1) Fix what appears to be a logic error in bgmac_phy_advertise.
2) Fix bgmac_ioctl to use passed phy_id; needed for switch-robo
interface w/ the driver to work correctly. I still have the issue
with the interface always being HD when the speed/duplex is set
manually (e.g., echo "100FD" > /proc/switch/eth0/port/N/media).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 35052
2013-01-07 22:51:39 +00:00
4ec57bdc06
update to 3.7
...
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35045
2013-01-07 18:16:36 +00:00
ba4de984b9
ar71xx: disable PHY_SWAP and PHY_ADDR_SWAP bits on TL-WR703N/MR3020/MR3040/MR11U boards
...
The PHY_SWAP and PHY_ADDR_SWAP bits are initialized
differently by different versions of the bootloader.
This leads to broken ethernet connection with OpenWrt
on some boards.
Turn both SWAP bits OFF on these boards to make it
consistent regardless of the bootloader used.
Based on a patch by Michel Stempin <michel.stempin@wanadoo.fr>.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35037
2013-01-07 14:30:37 +00:00
251e4608b0
ar71xx: add missing Makefile entry to the 74HC153 GPIO patch
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35035
2013-01-07 14:14:41 +00:00
5154270694
orion: debloat the kernel some more
...
SVN-Revision: 35023
2013-01-06 15:09:47 +00:00
75657ff8a9
kernel: add missing config symbol
...
SVN-Revision: 35021
2013-01-06 15:09:39 +00:00
f2f9332350
adds support for Edimax BR-6524N
...
fixes #12754
Signed-off-by: <rq@akl.lt>
SVN-Revision: 35020
2013-01-06 11:11:42 +00:00
d5d2e8b4db
missing underscore in 3.3 regmap patch
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 35018
2013-01-06 10:01:53 +00:00
2e8409cce3
kernel: port the regmap fix to 3.6 ( #12749 ), refresh patches for other versions
...
SVN-Revision: 35016
2013-01-05 13:33:44 +00:00
e6aac19237
fix regmap debloat patch
...
SVN-Revision: 35015
2013-01-05 00:20:05 +00:00
e952eaa112
bcm63xx: Add Huawei HG556a support
...
Add Huawei EchoLife HG556a support.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo@openwrt.org: added some code style fixes]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35011
2013-01-04 14:47:57 +00:00
0e58173fa5
bcm63xx: Fix caldata partition mtd patch
...
Allow bcm63xxpart to receive a caldata offset if calibration data is contained in flash.
Tested-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
SVN-Revision: 35010
2013-01-04 14:47:50 +00:00
10fc07daac
bcm63xx: remove 3.3 support
...
3.6 is tested enough to be considered stable.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35009
2013-01-04 14:47:43 +00:00
96f3911981
kernel: move regmap bloat out of the kernel image if it is only being used in modules
...
SVN-Revision: 34999
2013-01-03 18:39:50 +00:00
a105eea1a1
brcm47xx: various fixes and code cleanups for irq code
...
This is based on a patch send by Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 34997
2013-01-03 16:56:54 +00:00
4443997fd8
brcm47xx: add bgmac driver
...
This Ethernet driver is in early development stage and still has some problems.
This was working on my bcm4716 based device.
Thanks to Rafał Miłecki <zajec5@gmail.com> for writing this driver.
SVN-Revision: 34995
2013-01-03 02:05:22 +00:00
8f6bdcffa1
brcm47xx: build b44 as a module
...
SVN-Revision: 34994
2013-01-03 02:00:25 +00:00
22d62d311a
brcm47xx: run ifup before starting the switch
...
In addition check_module is not needed, nobody checks the return value.
SVN-Revision: 34993
2013-01-03 01:59:43 +00:00
97b2b601c7
brcm47xx: BCMA - IRQ Update - Fix IRQ Flag for I2S Core
...
Adjust the IRQ Flag value from 8 to 7 for I2S Core for BCM4716 and
BCM4748 (per the Broadcom SDK). IRQ Flag values greater than 7 are
ignored when setting the interrupt masks.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 34990
2013-01-03 01:56:13 +00:00
f74e847301
brcm47xx: improve IRQ handling for bcma based devices
...
This was party inspirited by patches send by Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 34989
2013-01-03 01:55:34 +00:00
25afeba608
brcm47xx: add a new version of the nvram rewrite patch
...
This is the version like it was send for mainline inclusion.
SVN-Revision: 34988
2013-01-03 01:53:30 +00:00
edc7ab525f
brcm47xx: move patches already in the mainline kernel to the front
...
SVN-Revision: 34987
2013-01-03 01:51:31 +00:00
76c767f122
brcm47xx: remove support for kernel version 3.3
...
SVN-Revision: 34986
2013-01-03 01:48:43 +00:00
7a73c2f91f
generic: add some missing kernel config symbols spotted on x86
...
SVN-Revision: 34981
2013-01-02 19:10:24 +00:00
741f6ba7ef
x86: fix typo in alix2/net5501 default packages
...
SVN-Revision: 34972
2013-01-02 16:09:23 +00:00
569bbe4970
rt5350 switch support fix
...
RT5350 frame engine need reset frame engine and embedded switch together.
Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
SVN-Revision: 34969
2013-01-02 11:28:21 +00:00
373b0b9ad1
generic: fix UBIFS build error if XZ compression is disabled
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34959
2013-01-02 08:53:07 +00:00
d91117459c
adm5120: add support for 3.7
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34954
2013-01-01 13:15:49 +00:00
f0520f1714
adm5120: nuke 3.3 support
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34953
2013-01-01 13:15:44 +00:00
b4315df8e1
adm5120: switch to 3.6
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34952
2013-01-01 13:15:41 +00:00
edd36342e5
adm5120: add support for 3.6
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34951
2013-01-01 13:15:36 +00:00
92cd48e9ea
adm5120: remove NAND_NO_AUTOINCR flag from rb1xx.c
...
Also add a compatibility patch for 3.3.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34950
2013-01-01 13:15:30 +00:00
03e09078dc
adm5120: use mtd_read helper in trxsplit.c
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34949
2013-01-01 13:15:20 +00:00
e1b13e15b2
adm5120: don't include asm/system.h in adm5120-hcd.c
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34948
2013-01-01 13:15:16 +00:00
cbe5d664e1
generic: add missing symbol for 3.7
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34947
2013-01-01 13:15:11 +00:00
e1965a1d1a
ar71xx: register the NAND flash controller device on the AP135/136 boards
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34946
2013-01-01 13:10:41 +00:00
66efec6783
ar71xx: allow to register the NAND flash controller on the QCA955x
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34945
2013-01-01 13:10:36 +00:00
2c77e5d7b3
ar71xxx: allow to select ATH79_DEV_NFC for QCA955x
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34944
2013-01-01 13:10:34 +00:00
d8446d65fe
ar71xxx: allow to build the ar934x_nfc driver for QCA955x
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34943
2013-01-01 13:10:29 +00:00
93c322cacc
ar71xx: fix NAND controller base for QCA955x SoCs
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34942
2013-01-01 13:10:26 +00:00
b57cc9a538
ar71xx: fold AP135 patch
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34941
2013-01-01 13:10:22 +00:00
624eb36fff
adds missing symbol
...
SVN-Revision: 34939
2012-12-30 21:31:10 +00:00
ce57efa3ea
fixes usb port on arv 4518
...
SVN-Revision: 34935
2012-12-30 12:38:40 +00:00
fb07876f25
ramips: rt305x: fix garbled name in mach-mzk-w300nh2.c
...
Signed-off-by: Samir Ibradžić <sibradzic@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34934
2012-12-30 08:23:48 +00:00
6708d68c24
ramips: build firmware image for the Planex MZK-W300NH2 Router
...
Signed-off-by: Samir Ibradžić <sibradzic@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3077/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34927
2012-12-29 17:50:40 +00:00
8b1ac2ae37
ramips: add user-space support for the Planex MZK-W300NH2 Router
...
Signed-off-by: Samir Ibradžić <sibradzic@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3077/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34926
2012-12-29 17:50:38 +00:00
d6d06aceb0
ramips: rt305x: add kernel support for the Planex MZK-W300NH2 Router
...
This is a Japanese market router, for details check
http://www.planex.co.jp/product/router/mzk-w300nh2/ . It has only 16MB
RAM, but base OpenWRT install worked fine for days without issues.
Even an image with built-in Luci worked, but don't expect smooth
experience, due to the lack of RAM. Wifi was not extensively tested,
but seems it is working. GPIO LEDs & buttons, factory flash image and
switch config are confirmed working. Tested against revision 34882 +
this patch.
[juhosg: move user-space support and image generation changes into
separate patches]
Signed-off-by: Samir Ibradžić <sibradzic@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3077/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34925
2012-12-29 17:50:35 +00:00
76537041eb
ramips: build image for Airlive AIR3GII
...
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/2913/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34924
2012-12-29 17:50:34 +00:00
3aad9b4c9b
ramips: add user-space support for Airlive AIR3GII
...
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/2913/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34923
2012-12-29 17:50:32 +00:00
3fcb8bb0dd
ramips: rt305x: add kernel support for AirLive AIR3GII
...
AirLive AIR3GII is Ralink RT5350F based device with
100Mbps switch, USB port, 4MB flash and 32MB ram.
Works: ethernet (LAN & WAN), wps button, led, USB, sysupgrade
Does not work: wifi (chip RT5350), reset button
[ 13.390000] phy0 -> rt2800_init_eeprom: Error - Invalid RT chipset 0x5350 detected.
[ 13.400000] phy0 -> rt2x00lib_probe_dev: Error - Failed to allocate device.
Other problem: LAN leds is reverse (lights when not cable
connected and vice versa)
[juhosg: move user-space support and image generation changes into
separate patches]
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/2913/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34922
2012-12-29 17:50:28 +00:00
87271e9f28
ar71xx: add support for 3.7
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34920
2012-12-29 16:02:31 +00:00
a3a6e0f039
ar71xx: Build the AP135 images
...
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34919
2012-12-29 16:02:28 +00:00
dddf05bde2
ar71xx: Add userspace support for AP135
...
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34918
2012-12-29 16:02:27 +00:00
1a379c5112
ar71xx: Add support for AP135
...
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34917
2012-12-29 16:02:24 +00:00
c6580f64b8
ar71xx: use a backported patch to fix AR933x UART baud rate calculation
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34915
2012-12-29 13:52:38 +00:00
348dc70c8c
ar71xx: change the unaligned access hack to assume an alignment of 2 bytes, slightly improves performance and code size
...
SVN-Revision: 34912
2012-12-28 21:30:24 +00:00
41a039f464
mips: use -mno-branch-likely for kernel and userspace, saves ~11k kernel size after lzma and ~12k squashfs size in the default configuration
...
SVN-Revision: 34909
2012-12-28 19:17:19 +00:00
9bb8b9fadb
kernel: remove the cisco SIP NAT patch, at least on 3.6 it crashes
...
SVN-Revision: 34901
2012-12-27 22:59:51 +00:00
981b7410f8
brcm47xx: bcma: correct M25P32 serial flash ID
...
Thank you Rafał Miłecki.
SVN-Revision: 34900
2012-12-27 19:18:40 +00:00
386c37b4c2
mpc83xx: add support for 3.7
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34892
2012-12-26 10:40:54 +00:00
f67a7a479e
mpc83xx: nuke 3.3 support
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34891
2012-12-26 10:40:51 +00:00
36af140fe4
mpc83xx: switch to 3.6.11
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34890
2012-12-26 10:40:50 +00:00
c4c8307ca1
mpc83xx: add support for 3.6
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34889
2012-12-26 10:40:48 +00:00
e537b8a093
mpc83xx: create package for the rbppc_cf module
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34888
2012-12-26 10:40:47 +00:00
fff75fe5b6
generic: more missing symbols for 3.{6,7}
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34887
2012-12-26 10:40:41 +00:00
f5b1cba606
ar71xx: build image for the AP136-020
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34886
2012-12-26 09:50:37 +00:00
Florian Fainelli
Mirko Vogt
Gabor Juhos
Hauke Mehrtens
Jonas Gorski
John Crispin
Felix Fietkau
Jo-Philipp Wich
Imre Kaloz