Rework (again) platform support for dual-role chipidea USB controller:
- include support for QCA9531
- use correct EHCI block size
- drop ar933x_usb_setup_ctrl_config() function
- simplify code after previous "register chipidea only in device mode"
change (fa22714181)
Reworked patch was tested on devices with below QCA WiSOCs (signal/GPIO
name with required bootstrap state for USB bus 0 in device mode):
- AR9331 (GPIO13 pull-down)
- AR9342 (RGMII_TXD1/ETXD1 pull-up)
- AR9344 (GPIO20 pull-up)
- QCA9531 (GPIO13 pull-up)
- QCA9558 (GPIO13 pull-up)
The only way to select device mode for bus 0 is to change SOC bootstrap
configuration which is sampled only once, at hard reset. Likely, other
models, like QCA9556 or AR9341, should also support dual-role USB mode
but they were not tested.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Supports IPv4 flow offloading on MT7621 for Routing, SNAT and DNAT
Supported are regular ethernet->ethernet connections, including one
802.1q VLAN and/or PPPoE encapsulation
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Bug fix release. 1.28.3 has fixes for
* ash and hush (do not leave stray open file destriptors in children),
* cpio (fix for symlink extraction),
* grep ("grep -Fw a" was matching "aa").
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
74b5a3 script: fix possible negative delay
473f248 dhcpv6: always trigger script update in case of IA updates
ea18935 ra: rework route information option handling
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
of_dma_configure() sets a default ->dma_mask of
DMA_BIT_MASK(32), claiming devices can DMA from
the full 32bit address space.
The mtk-mmc driver does not support access to
highmem pages, so it is really limited to the
bottom 512M (actually 448M due to 64M of IO space).
Setting ->dma_mask to NULL causes mmc_setup_queue()
to fall-back to using BLK_BOUNCE_HIGH to tell the
block layer to use a bounce-buffer for any highmem
pages requiring IO.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
- avoid using garbage stack values as dst pointer if lookup fails
- provide the source address for ipv6 dst lookup
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Our .dts files only have one device defined and this is unlikely to
change, so statically initialize host->id to 0.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This commit adds correct model detection for UniFi
AC-Mesh. Previously said device was incorrectly detected
as UniFi AC-Lite.
The Information about the device is stored at 0xC in the EEPROM
partition. It corresponds to the sysid in /etc/board.info of the
Ubiquiti stock firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
D-Link DAP-1330 rev. A1 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR1)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 2x external antennas
- 6x LED (2 are bi-color), 2x button
- 4 pin on pcb (looking from eth port and from left to right tx,rx,gnd,vcc)
Flash instruction: use "factory" image directly in vendor GUI.
This device has a recovery system that assign the ip addr of env
variable "serverip" via dhcp to a pc, and the "ipaddr" value to itself.
The recovery it's triggered by a not bootable firmware,
or pressing the reset button during the bootloader startup (first 30 seconds).
The recovery uses a http page to restore the firmware, and it's checking
the firmware image header, so use the "factory" image to
restore or the original firmware.
You can access vendor firmware over serial using:
- login: root
- password: linuxrocks
Image was tested only in EU version of the device, but should work
also with the same device version sold in other countries.
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
Commit d6d3db0543 added more gcc version probes, exceeding the argument
limit of the SetupHostCommand macro, leading to failing GCC/LLVM tests
on OS X.
Extend the handled number of arguments to restore proper functionality.
Fixes FS#1470
Fixes d6d3db0543 ("build: Improve GCC version detection")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Some packages are already using $(1)/var on package install.
On multiuser systems this breaks the build when multiple
users build OpenWrt.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
This reverts commit 4fb684a755.
The compile fixes are still required for host systems using GCC 5.x,
such as Ubuntu 16.04 LTS.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
It was wrong from the beginning and the trigger for the wan led was
never set due to the typo.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
[add commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
It's intentional that some boards within a target don't have all LEDs
which are tried to be setup in a common script. Don't show a warning in
such cases.
Fixes: 4f4fc993db ("base-files: add more name source to get_dt_led helper function")
Signed-off-by: Mathias Kresin <dev@kresin.me>
We need to reset the GPHYs on reboot as well. Otherwise the bootloader
might have issues to reset/find the GPHYs.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The DWR-921-C3 Wireless Routers with LTE embedded modem is based on the
MT7620N SoC.
Specification:
* MediaTek MT7620N (580 Mhz)
* 64 MB of RAM
* 16 MB of FLASH
* 802.11bgn radio
* 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
* 2x external, detachable (LTE) antennas
* UART header on PCB (57600 8n1)
* 6x LED (GPIO-controlled)
* 1x bi-color Signal Strength LED (GPIO-controlled)
* 2x button
* JBOOT bootloader
Installation:
Apply factory image via d-link http web-gui.
How to revert to OEM firmware:
1.) Push the reset button and turn on the power. Wait until LED start
blinking (~10sec.)
2.) Upload original factory image via JBOOT http (IP: 192.168.123.254)
3.) If http doesn't work, it can be done with curl command:
curl -F FN=@XXXXX.binhttp://192.168.123.254/upg
where XXXXX.bin is name of firmware file.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The DWR-921-C1 Wireless Routers with LTE embedded modem is based on the
MT7620N SoC.
Specification:
* MediaTek MT7620N (580 Mhz)
* 64 MB of RAM
* 16 MB of FLASH
* 802.11bgn radio
* 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
* 2x external, detachable (LTE) antennas
* UART header on PCB (57600 8n1)
* 6x LED (GPIO-controlled)
* 1x bi-color Signal Strength LED (GPIO-controlled)
* 2x button
* JBOOT bootloader
The status led has been assigned to the dwr-921-c1:green:sigstrength (lte
signal strength) led. At the end of the boot it is switched off and is
available for lte operation. Work correctly also during sysupgrade
operation.
Installation:
Apply factory image via d-link http web-gui.
How to revert to OEM firmware:
1.) Push the reset button and turn on the power. Wait until LED start
blinking (~10sec.)
2.) Upload original factory image via JBOOT http (IP: 192.168.123.254)
3.) If http doesn't work, it can be done with curl command:
curl -F FN=@XXXXX.binhttp://192.168.123.254/upg
where XXXXX.bin is name of firmware file.
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
Backport patch which adds suport for the BroadMobi BM806U 3G/4G modem,
which is used in D-Link DWR-921 C3.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Backport patch which adds suport for the Wistron NeWeb d18q1 LTE modem
which is used in D-Link DWR-921 C1.
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
drivers/mmc/host/mtk-mmc/dbg.c:51:13: warning: 'cmd_buf' defined but not used [-Wunused-variable]
static char cmd_buf[256];
^~~~~~~
In addition, msdc_reg[] is completely unused, even in debug
mode.
Signed-off-by: André Draszik <git@andred.net>
msdc_6575_host[] is unused, just remove it. Also, it
was the source of memory corruption up until the
previous fix to this driver.
Signed-off-by: André Draszik <git@andred.net>
pdev->id is -1 when only one device exists, and is used:
* as an index into drv_mode[] to determine whether to use
PIO or DMA mode (via host->id)
* as an index into msdc_6575_host[], to store the
mmc_priv() data.
Obviously, -1 is not a valid index in either case, causing
us to read invalid memory, and memory corruption,
respectively.
The invalid memory read is causing non-deterministic
behaviour, in particular in the v4.4 kernel it still
picked DMA mode, but in the v4.9 it now always picks
PIO mode.
Also, PIO mode doesn't work, causing the following:
/ # echo 3 > /proc/sys/vm/drop_caches
[ 3845.249237] sh (128): drop_caches: 3
/ # /root/usr/lib/libc.so
[ 3846.096070] do_page_fault(): sending SIGSEGV to libc.so for invalid read access from 7f9cb5a0
[ 3846.104758] epc = 779b0ea4 in libc.so[7792f000+c3000]
[ 3846.109907] ra = 779a8004 in libc.so[7792f000+c3000]
Segmentation fault
/ # /root/usr/lib/libc.so
musl libc (mipsel-sf)
Version 1.1.16-git-40-g54807d47
Dynamic Program Loader
Usage: /root/usr/lib/libc.so [options] [--] pathname [args]
(i.e. initial page-in of any binary causes a segfault,
subsequent access works.)
While this change doesn't fix PIO mode, it at least makes
us deterministically use DMA (which works), and it also
stops us from corrupting memory.
Signed-off-by: André Draszik <git@andred.net>
drivers/mmc/host/mtk-mmc/sd.c:2782:5: warning: this 'if' clause does not guard... [-Wmisleading-indentation]
if ((hw->flags & MSDC_SDIO_IRQ) || (hw->flags & MSDC_EXT_SDIO_IRQ))
^~
drivers/mmc/host/mtk-mmc/sd.c:2785:2: note: ...this statement, but the latter is misleadingly indented as if it is guarded by the 'if'
cd_active_low = !of_property_read_bool(pdev->dev.of_node, "mediatek,cd-high");
^~~~~~~~~~~~~
Signed-off-by: André Draszik <git@andred.net>
It seems both issues (GCC5 and Musl) were fixed at some point. Thus, they can be dropped.
Did not bump version as there is no change in functionality or size.
Compile-tested on ar71xx and mvebu, both with musl.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
flash_erase utility allows to erase MTD partitions on NAND flash.
Useful when you want to clean or write an MTD partition from scratch.
e.g., before using kobs-ng to flashing SPL images it's recommended
to erase the MTD partition to ensure it's empty.
Signed-off-by: Adrià Llaudet <adria.llaudet@gmail.com>
Update busybox to 1.28.2, refresh patches and default config.
* modify 230-add_nslookup_lede.patch as opt_complementary was removed
Also move nslookup_longopts variable declaration to be inside
the same conditional as the function itself.
* modify 250-date-k-flag.patch to match upstream (opt_complementary)
* remove 600-cve-2017-16544.patch that is upstreamed
Notes about config changes:
* Some applet-specific LONG_OPTIONS config options were removed
* Config help text indentation changed, caused lots of
text formatting changes for convert_menuconfig.pl
* convert_defaults.pl moved lots of defaults around, summary of
actual changes below
New applets/features:
---------------------
ARCH
HEXEDIT
MINIPS
NETCAT
NUKE
RESUME
RUN_INIT
SETFATTR
New options:
------------
FEATURE_CATN
FEATURE_CROND_SPECIAL_TIMES
FEATURE_LIBBUSYBOX_STATIC
FEATURE_SETPRIV_CAPABILITIES
FEATURE_SETPRIV_CAPABILITY_NAMES
FEATURE_SETPRIV_DUMP
FEATURE_SH_READ_FRAC
FEATURE_SWAPONOFF_LABEL
FEATURE_VOLUMEID_MINIX
FEATURE_XARGS_SUPPORT_ARGS_FILE
FEATURE_XARGS_SUPPORT_PARALLEL
HUSH_GETOPTS
HUSH_READONLY
HUSH_TIMES
Removed:
--------
FEATURE_HAVE_RPC
MSH
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
This Adds fixes for the following security problems based on debians patches:
CVE-2016-2125: Unconditional privilege delegation to Kerberos servers in trusted realms
CVE-2017-12163: Server memory information leak over SMB1
CVE-2017-12150: SMB1/2/3 connections may not require signing where they should
CVE-2018-1050: Denial of Service Attack on external print server.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This now makes sure that the beginning of the version number gets checked
and "4.4.5" will not match was a supported version.
GCC 8 and GCC 9 are now marked as supported, but we probably have to fix
some problems for them.
Closes: FS#1433
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These functions are not declared in any header file and only used in
same compile unit, mark them as static to remove one gcc warning and
make it easier for the compiler to optimize them out.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Piotr Dymacz
Peng Zhang
John Crispin
Felix Fietkau
Hannu Nyman
Hans Dedecker
NeilBrown
David Bauer
Nicolò Veronese
Jo-Philipp Wich
Alexander Couzens
Reto Schneider
Mathias Kresin
Pawel Dembicki
Giuseppe Lippolis
André Draszik
Sebastian Fleer
Daniel Engberg
Rosen Penev
Adrià Llaudet
Hauke Mehrtens
Paul Wassi