Commit Graph

174 Commits (a0a9ba046492e952aa5cab042d96bec4cab6e17f)

Author SHA1 Message Date
Kristian Evensen bb7068f26c ramips: add support for Sanlinking D240
The Sanlinking Technologies D240
(http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same
device as the ZBT WE826, so adding support for it in LEDE is straight forward.
The differences is that the D240 has two mini-PCIe slots (instead of one), blue
LEDs and supports PoE.

Specification:
* CPU: MT7620A
* 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps.
* 16 MB Flash.
* 128 MB RAM.
* 1x USB 2.0 port.
* 2x mini-PCIe slots.
* 2x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.

Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to
test the SD card reader.

The device comes pre-installed with an older version of OpenWRT, including Luci.
In order to install LEDE, you need to follow the existing procedure for updating
OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to keep
existing settings. The default router address is 192.168.10.1 and
username/password admin/root (at least on my devices).

If you brick the device, the procedure for recovery is the same as for the
WE826. Please see the wiki page for that device for instructions.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-02-05 22:23:28 +01:00
FUKAUMI Naoki 6b0b526a4f ramips: add support for Buffalo WCR-1166DS
Buffalo WCR-1166DS is a small wireless router with

 - MT7628AN + MT7612E
 - 64MiB DDR2 SDRAM
 - 16MiB SPI flash
 - 2T2R 11ac/a/b/g/n Wi-Fi
 - 2x 10/100M ethernet switch
 - 8x programmable LED
 - 3x button
 - UART pad on PCB (J2: 3.3V, GND, TX, RX)

factory image can be installed via stock web UI.

due to the "dual image" function in the bootloader, the second half of
the SPI flash ("firmware2" partition) cannot be used as a part of the
file system.

Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
2017-01-31 11:10:58 +01:00
Thibaut VARENE 7fb11c8ed2 ramips: add support for Netgear WN3000RPv3
This patch adds support for the Netgear WN3000RPv3
http://www.netgear.com/support/product/wn3000rpv3.aspx

Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Serial: JP1 header, 57600-8N1
- Stock firmware based on OpenWRT Kamikaze

Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This is why the same fakeroot image is used for the WN3000

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-01-18 12:06:16 +01:00
Lazar Demin ab90f15c89 ramips: Added Onion Omega2 and Omega2+
This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io)

Specifications:
- SoC: MediaTek MT7688AN (580MHz, ramips)
- Omega2
  - RAM: 64MB DDR
  - Storage: 16MB NOR SPI flash onboard
- Omega2+
  - RAM: 128MB DDR
  - Storage: 32MB NOR SPI flash onboard + microSD slot
- Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter
- Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port
- Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock)
  - All Docks Provide:
    - Micro-USB port to provide power to the Omega
      - On the Expansion and Mini Docks, can also access the terminal (UART0) via serial
    - USB 2.0 socket connected to Omega
  - Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide:
    - Omega GPIO breakout
    - Allows for connection of Omega Expansions:
      - Ethernet Expansion
      - Relay Expansion
      - PWM Expansion
      - OLED Expansion
      - Ethernet Expansion
      - Proto Expansion
      - Cellular Expansion

Signed-off-by: Lazar Demin <lazar@onion.io>
2017-01-15 17:43:14 +01:00
Andrew Yong 3f31029b19 ramips: add support for VoCore2
This patch adds support for the VoCore VoCore2 and its complementary
"ultimate" dock.

Specifications:
- SoC: MediaTek MT7628AN (580MHz, ramips)
- RAM: 128MB DDR2 166MHz
- Storage: 16MB NOR SPI flash onboard + microSD slot on dock
- Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2
            boards with onboard 1x chip antenna
- Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header
- Dock hardware:
  - USB 2.0 socket
  - MicroSD socket
  - 100Mbps Ethernet x1
  - 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S
    DAC/ADC (support WIP)
  - Micro USB for power and console (UART2)

Initial installation:
- VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on
  SSID "VoCore2"
- Connect to VoCore2 by Ethernet or Wi-Fi
- `ssh root@192.168.1.1` (password is "vocore")
- scp/wget/etc. LEDE sysupgrade.bin to VoCore2
- `sysupgrade -n <your image>.bin` (don't keep old config, as the
  original firmware uses Ralink SDK Wi-Fi drivers and not
  mt76+mac80211)
- after sysupgrade completes, Wi-Fi will be disabled by default so use
  Ethernet or the micro USB console to configure Wi-Fi again

Signed-off-by: Andrew Yong <me@ndoo.sg>
2017-01-13 08:32:35 +01:00
L. D. Pinney b28e94d4bf ramips: MiWiFi Nano fixes
Use the the dt-bindings macros and add the reset button.

Set the correct polarity for the LEDs and drop the default state.
Remove all trigger for the LEDs. According to the manual the LEDs are
only used to show the operation state, where blue means normal
operation.

Use the MAC-Addresses stored in EEPROM for the ethernet and the
wireless interface.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
[use leds only for boot status indication, add proper commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-01-02 19:16:54 +01:00
Mathias Kresin d2b1148e75 ramips: use D-Link DIR-600 B1 image for B2 version
Everything set for the B1 is identical to the values uses for the B2
version.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Henryk Heisig c8043137bb ramips: Add support to TP-Link Archer MR200
CPU: MT7620N 580MHz
Flash: 8MB
RAM: 64MB
build-in modem 3G/4G
four ethernet port 10/100Mbps

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-12-22 15:03:30 +01:00
Vitaly Chekryzhev 190ee7d86b ramips: add support for ZyXEL Keenetic Omni / Omni II
Factory image can be installed via Zyxel WebUI.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2016-12-22 15:03:13 +01:00
Tobias Wolf c2ed721e89 ramips: improve F5D8235 V1 support
This fixes the partition name for the firmware splitter, the cfi
address and adds the mtd-eeprom address for wmac. It adds additional
LEDs and make use of them in diag.sh and 01_leds.

Please note that the ":blue:wired" LED is used because the
":blue:router" behaviour is unpredictable for failsafe indication. The
issue with the router LED is that you have two states only.
"off" is steady on and "on" blinks. Therefore the wired LED is more
suitable.

Furthermore it reuses the correct switch configuration definition to
reflect the device ports and numbering. Additionally fixes the issue
that the default configuration is not applied as no port 6 exists on
this device.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
2016-12-04 07:03:17 +01:00
Andrew Yong 07b571a435 ramips: RB750Gr3: Add pwr LED and buzzer to DTS
use pwr LED in diag.sh
Expose unused pinmux pins as GPIOs
export power LED and buzzer pins
Use rb750gr3:blue:pwr LED in diag.sh for boot status instead of rb750gr3:green:usr

Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-12-01 16:17:55 +01:00
Giuseppe Lippolis ec1de9b1a6 ramips: Add device DLINK DWR-512-B
The Dlink DWR-512-B modem is a ralink 5350 processor based embedding
a 3G mini-pcie router.

The oem JBOOT bootloader has to be replaced by a RT5350 SDK
U-Boot such as https://github.com/stevenylai/ralink_sdk - U-Boot
configured for the RT5350 256MiB SDR.

Main reason to change the bootloader is the encrypted header used to
store the kernel image. In this way an image can only be generated
using the propietary binboy tool (included in the GPL distribution
from Dlink). The binboy tool doesn't allow to modify the kernel/rootfs
partition scheme. This is considered a big constraint (limited kernel
size and inefficient usage of flash space).

For interested people I pubblished the details of my investigation
about the encrypted firmware header here:
http://lists.infradead.org/pipermail/lede-dev/2016-October/003435.html

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2016-11-23 08:36:11 +01:00
Vitaly Chekryzhev 348344874c ramips: add support for ZyXEL Keenetic Viva
Factory image can be installed via Zyxel WebUI.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
[removed linux,modalias parameter from flash node in dts]
[removed sdhci node from dts; no sd card slot here]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-18 08:54:57 +01:00
Jasper Scholte 3d680c5728 ramips: add support for Sitecom WLR-6000
The Sitecom firmware upgrade file has SENAO_FIRMWARE_TYPE 2 set. This
looks rather wrong since SENAO_FIRMWARE_TYPE 2 is kernel only but the
file is way to big for only including a kernel.

The factory image need to have the dlf file extension. Otherwise the
Sitecom firmware rejects the file.

The stock firmware uses the following mac addresses:

LAN: 00:0C:F6:AA:BB:D8 (u-boot env: ethaddr)
2,4: 00:0C:F6:AA:BB:D8 (EEPROM)
5:   00:0C:F6:AA:BB:DC (EEPROM)
WAN: 00:0C:F6:AA:C8:43 (u-boot env: wanaddr)

Assuming the mac address range :D8 to :DC is reserved for this device,
the MAC addresses were reorder to have a unique MAC address for each
interface:

2.4GHz: 00:0C:F6:AA:BB:D8
LAN:    00:0C:F6:AA:BB:D9
WAN:    00:0C:F6:AA:BB:DA
5 GHz:  00:0C:F6:AA:BB:DC

The first MAC is assigned to the 2.4GHz WiFi interface
to keep compatibility with the SSIDs printed on the case, which have
the last three sextets of the MAC address appended.

There are still issues with the rt2x00 driver. It is not possible to
use both wireless interfaces at the same time. The 2.4 GHz
wireless (PCIe) only works if the internal 5GHz wireless is/has been
enabled or used for scanning. The internal 5GHz wireless only works if
the 2.4GHz wireless (PCIe) was never enabled. Disabling the 2.4Ghz
after it was enabled will result in stations seeing the 5Ghz AP but are
unable to connect.

Due to the not optimal working wifi the manufacture, backup and storage
partitions of the OEM firmware are kept for now to allow an easy switch
back to the Sitecom firmware.

Signed-off-by: Jasper Scholte <NightNL@outlook.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-17 06:39:52 +01:00
Dominik Menke 8b65fef173 ramips: add support for Digineo AC1200 Pro
This is basically a ZBT-WG3526 (mt7621 SoC), but with 32M flash.

Signed-off-by: Dominik Menke <dom@digineo.de>
2016-11-17 06:39:52 +01:00
Felix Fietkau a17872ec4f ramips: fix status LED for WHR-300HP2
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-14 17:55:27 +01:00
Andrew Yong faf94d926e ramips: add support for MikroTik hEX v3 (RB750Gr3)
The MikroTik hEX v3 (RB750Gr3) is a MT7621AT board which is similar to most MT7621 reference designs, it can be easily supported by this patch; however, the stock RouterBOOT bootloader has to be replaced by a MT7621 SDK U-Boot such as https://github.com/ndoo/RB750Gr3-U-Boot - U-Boot configured for the RB750Gr3 (16MiB SPI flash, 256MiB DDR3 RAM at 1200MHz).

RouterBOOT, the stock bootloader, does not initialize the UART and boots silently, making it preferable to replace it with a MT7621 SDK U-Boot with UART (57600 8N1) that supports HTTP, TFTP or serial upload of sysupgrade firmware and U-Boot.

Furthermore, RouterOS, the stock firmware, is contained in a proprietary modification of SquashFS without GPL sources; UART is also disabled in stock firmware.

The combination of LEDE firmware generated by this PR and MT7621 SDK U-Boot expects the printed MAC address to reside at offset `0xe000` of the factory partition (absolute offset is `0x4e000`); this is similar to the factory MAC address offset for several other MT7621 devices.

A 16MiB flash dump suitable for use with flashrom will be provided if/once this patch is accepted and binaries are built by LEDE buildbot. Alternatively, writing the U-Boot to the SPI flash starting at 0x0 offset and booting the board with serial console attached will allow TFTP, HTTP or serial upload of sysupgrade firmware.

Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-11-02 10:25:44 +01:00
Henryk Heisig a34f96d6cf ramips: Archer C50 cleanup
- setting read-only flag to important partitions
- enabling PA to improve 2.4 GHz signal strength
- add missing leds
- rename colour led
- add mac adress to 5GHz wlan interface
- included <dt-bindings/input/input.h> and <dt-bindings/gpio/gpio.h>

Signed-off-by: Henryk Heisig hyniu@o2.pl
2016-10-31 16:58:41 +01:00
Xuefu Lin 8312738806 ramips: fix PSG1218 LEDs
Signed-off-by: Xuefu Lin  <xuefulin@gmail.com>
2016-10-26 12:37:45 +02:00
YuheiOKAWA 4050cfebda ramips: add support for Planex VR500.
SOC:	MT7621A
RAM:	256MiB
NOR:	MX25L51245G

Non Wireless Router.

Issue: soft reboot problem. SPI Flash do not exit 4byte address mode.

Signed-off-by: Yuhei Okawa <tochiro.srchack@gmail.com>
2016-10-15 11:36:51 +02:00
Mathias Kresin 6391af2f1f ramips: improve edimax 6200n/nl support
Assign the reset functionality to the wps/reset buttons. Use the wlan
switch of the 6200n to enable/disable wlan.

Add the internet led of the 6200nl and use the led for boot status
indication

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Klaus df5416296c ramips: add support for Zyxel NBG-419N2 (WAP3205v2)
applied bb-final-ramips-add-zyxel-nbg-419n2.patch from
123serge123, found at https://yadi.sk/d/1ZV0lKJwbTE65;
see https://forum.openwrt.org/viewtopic.php?pid=246905#p246905,
modified slightly to fit to CC release and to new lede build
system: image/rt305x.mk include file is used now
changed NBG-419N2.dts format to fit style of other dts files

Signed-off-by: Klaus <k-laus@quantentunnel.de>
2016-10-04 11:50:51 +02:00
Xuefu Lin dce5c4f5c8 ramips: Add support for Phicomm K2 PSG1218
- CPU: MT7620A 580MHz
- Flash: 8MB - RAM: 64MB
- External PA+LNA on both WLAN2.4 and WLAN5
- 4x LAN ethernet and 1x WAN ethernet

Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
2016-10-04 11:50:46 +02:00
Cezary Jackiewicz e79e555c0e ramips: Xiaomi MiWiFi Nano: fix status led
- add status led for Xiaomi MiWiFi Nano
- revert af1e70b4a7 , this should not be added.

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-09-29 11:39:41 +02:00
BangLang Huang 142ec7ada9 ramips : add support for Newifi D1
Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2016-09-27 17:50:22 +02:00
BangLang Huang 9fe833e1d0 ramips : add support for PandoraBox D1
Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2016-09-27 17:50:22 +02:00
Cezary Jackiewicz 66aae9a271 ramips: Add support for ZBT-CPE102
- CPU: MT7620N 580MHz
- Flash: 8MB
- RAM: 64MB
- build-in minipcie slot for modem 3G/4G
- one ethernet port 10/100Mbps

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-09-27 17:50:21 +02:00
Daniel Golle 083ef3fefe ramips: add support for Mercury MAC1200R v2
MT7628AN + MT7612E, 8MB SPI flash, 64MB DDR RAM
reset button GPIO is still missing (anyone?)
bootloader password is 'slp'

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2016-09-09 02:38:06 +02:00
Chuanhong Guo 0f73801f4f ramips: Add support for Thunder Timecloud
Thunder Timecloud is a small NAS with MT7621A. It has 1 USB port and an
SD Card slot. There is no wireless cards.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2016-08-10 03:04:08 +02:00
Michael Lee c3e420f28c ramips: Add support for D-Link DCH-M225
D-Link DCH-M225 is based on Mediatek MT7620 with 64MB ram, 8MB flash,
3.5mm audio out support. but no ethernet and usb ports.
so you must default enable wifi.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-07-11 14:19:47 +02:00
Matthias Schiffer 103ed00cfb
ramips: add button support and make LEDs known to userspace for DIR-860L B1
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
2016-06-30 17:12:38 +02:00
Henryk Heisig 75af981239 ramips/base-files: Add support for Archer C50
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-06-13 22:51:43 +02:00
Yuan Chenmang b38296f2f6 ramips: add Widora-NEO board support
The Widora board is similar to the Linkit 7688 but features a larger flash
capacity.

Signed-off-by: Yuan Chenmang <771992497@qq.com>
[Jo-Philipp Wich: Reword commit message, cleanup initial PR]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-06-01 12:52:28 +02:00
Felix Fietkau 5166732a4e ramips: use green power LED as status indicator for Buffalo WSR-1166 and WSR-600
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-21 15:16:37 +02:00
Andrew Yong 8c9b8d70b1 ramips: add status led for ZBT-WE826
Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-05-12 03:29:36 +02:00
Andrew Yong 374cae9e6f ramips: add initial support for SamKnows SK-WB8
Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-05-12 03:29:35 +02:00
blogic 6b0425a187 ramips: add support for Planex MZK-EX750NP.
add support for Planex MZK-EX750NP.
MZK-EX750NP is MT7620A and MT7610E based 11ac wifi repeater.
Built-in power supply.
64MiB RAM, 8MiB SPI Flash, non Wired Ethernet.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 49268
2016-05-10 10:43:12 +02:00
John Crispin cb049e71cd ramips: Add support for the Netgear WNDR3700v5
https://wiki.openwrt.org/toh/netgear/wndr3700

wndr3700v5 uses the single-core dual thread MediaTek MT7621S SoC.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 49247
2016-04-26 11:43:53 +00:00
John Crispin 279eeeb744 ramips: add support for Planex MZK-EX300NP
MZK-EX300NP is MT7620A based wifi repeater.
Built-in power supply.
64MiB RAM, 8MiB SPI Flash, non Wired Ethernet.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 49235
2016-04-26 11:43:06 +00:00
John Crispin e55d86ef32 ramips: add support for Planex CS-QR10
CS-QR10 is MT7620A based IP Camera.

the camera and sound does not work with kernel 4.4.
 - camera chip is sn9c291.
 - sound chip is wm8960.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 49234
2016-04-26 11:43:01 +00:00
John Crispin 30fbc1a4d1 ramips: Add support for ZBT WG3526
The WG3526 is the follow-up to the 2626 and is mostly the same, with the
excaption that the mt7602 has been replaced with the mt7603. The internal wifi
setup has also changed slightly. Based on my tests, everything that worked on
the 2626 works on the 3526 and with roughly the same performance.

v1->v2:
* Remove some references to 2626 that I had missed in the dts.

v2->v3:
* Update patch to match new file structure.
* Removed SD driver to be consistent with other MT7621 targets.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>

SVN-Revision: 49213
2016-04-21 19:47:08 +00:00
John Crispin 37b50fdb92 ramips: add support for ELECOM WRH-300CR
ELECOM WRH-300CR is MT7620N based very small Wi-Fi router with 64MiB
DDR2 SDRAM, 16MiB SPI Flash, one fast ethernet port, and (internal but
easy-to-access) UART.

it also has internal USB hub and USB card reader which provide one USB
port, one SD card slot, and one microSD card slot.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>

SVN-Revision: 49211
2016-04-21 19:46:59 +00:00
John Crispin 890eb0c126 ramips: fix support Planex MZK-750DHP.
fix script for Planex MZK-750DHP.
modification of the GPIO definition.
add Profile.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 49205
2016-04-20 17:19:05 +00:00
John Crispin 43dd2b9965 ramips: Add JCG routers to base-files
This patch adds support for JHR-N805R, JHR-N825R and JHR-N926R to
various scripts in the base-files directory.

Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>

SVN-Revision: 48905
2016-03-04 08:33:09 +00:00
John Crispin 8b38a9450b ramips: Add support for Phicomm PSG1208
This patch adds support for Phicomm PSG1208.This is a router with MT7620A SoC with 8M flash and 64M ram.
The WPS led is uesd as status_led because the power light can't be controlled with GPIO.
It seems that the 5g wifi led is connected to MT7612E and it can't be controlled with GPIO too.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>

SVN-Revision: 48721
2016-02-15 18:45:22 +00:00
John Crispin 9f9682a79b ramips: Add support for Netgear EX2700
This patch adds support for the Netgear EX2700 and builds an approriate
sysupgrade image.

What's missing is the option to build a factory image flashable via the
router's stock web interface, but this approach is hindered by the fact
that u-boot operforms an additional integrity check, which expects a
uImage header in the last 64 bytes of the "kernel" partition, which
the bootloader expects to be 960k, a size exceeded by the standard
OpenWrt kernel.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>

SVN-Revision: 48698
2016-02-12 08:29:33 +00:00
John Crispin de7dce21a3 ralink: add WRTnode2 platform and led support
Signed-off-by: xzmu <xzmu@wrtnode.com>

SVN-Revision: 48049
2016-01-01 21:19:50 +00:00
John Crispin 9f14006809 ramips: add additional support for MQmaker WiTi board
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram,
2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and
one 5 ghz antenna.

This is the 6th submission that adds support for XHCI in the device tree
file, along with switching the location of the 2 radio's and addition of
the kmod-i2c-mt7621 in the default packages of the profile.

Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>

SVN-Revision: 47845
2015-12-11 15:04:13 +00:00
John Crispin 6cbb1be464 ramips: Fix support for PBR-M1 board
The PBR-M1 support in current OpenWrt is for the early demo board and it doesn't work on the final board.This patch fixes the support for it.

The LED called pbr-m1:buzzer is a beeper connected to GPIO26 so I used gpio-beeper instead of gpio-leds.

Signed-off-by: 郭传鈜 <gch981213@gmail.com>

SVN-Revision: 47844
2015-12-11 15:03:50 +00:00
John Crispin 8c1f5141ce ralink: add support for netis WF-2881
netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN.
It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.

this device only works on top of UBI.

Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons (reset button)
* ethernet switch and USB diag LEDs
* UART
* GPIOs
* sysupgrade

Tested and not working
* failsafe

Signed-off-by: YounJae Rho <luxflow@live.com>

SVN-Revision: 47619
2015-11-24 18:29:26 +00:00