Commit Graph

311 Commits (9c6b6abdcd68fe1bb19c4dff472a1a7cc9cbb974)

Author SHA1 Message Date
Daniel Golle d1130ad265 ath79: add support for Teltonika RUT955
Specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344)
- built-in 4G/3G module (example: Quectel EC-25EU)
- internal microSD slot (spi-mmc, buggy and disabled for now)
- RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0)
- RS422/RS485 (AR934x high speed UART, /dev/ttyATH1)
- analog 0-24V input (MCP3221)
- various digital inputs and outputs incl. a relay
- 11x LED (4 are driven by AR9344, 7 by 74HC595)
- 2x miniSIM slot (can be swapped via GPIO)
- 2x RP-SMA/F (Wi-Fi), 3x SMA/F (2x WWAN, GPS)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- debugging UART available on PCB edge connector

Serial console (/dev/ttyS0) pinout:

- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side

Flash instruction:

Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.2".

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-02-21 22:35:12 +01:00
Adrian Schmutzler 2f1cc5c3d5 ath79: add support for TP-Link TL-WA701ND/730RE/801ND/901ND v1
This adds support for the various clones of the TL-WA830RE recently
supported in fb99ac6807 ("ath79: add support for TP-Link TL-WA830RE v1"):

- tplink,tl-wa701nd-v1
- tplink,tl-wa730re-v1
- tplink,tl-wa801nd-v1
- tplink,tl-wa830re-v1 (already supported)
- tplink,tl-wa901nd-v1

Since these devices are 100%-clones in ar71xx, this patch adds all
of them without run-testing (as this has been done for TL-WA830RE v1).

Specifications:
- SOC: Atheros AR7240
- CPU: 400MHz
- Flash: 4 MiB (Spansion S25FL032P)
- RAM: 32 MiB (Zentel A3S56D40FTP-G5)
- WLAN: Atheros AR9280 bgn 2x2
- Ethernet: 1 port (100M)

Flash instructions:
- install from u-boot with tftp (requires serial access)
  > setenv ipaddr a.b.c.d
  > setenv serverip e.f.g.h
  > tftpboot 0x80000000 \
      openwrt-ath79-tiny-tplink_tl-waxxxxx-v1-squashfs-factory.bin
  > erase 0x9f020000 +0x3c0000
  > cp.b 0x80000000 0x9f020000 0x3c0000
  > bootm 0x9f020000
- flash factory image from OEM WebUI
- sysupgrade from ar71xx image

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-21 13:55:33 +01:00
David Bauer 0709943182 ath79: correct Siemens WS-AP3610 blocksize
With the wrong blocksize, the rootfs was not positioned on the boundary
of a block, thus breaking the mtdsplit driver.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-02-20 10:41:12 +01:00
Adrian Schmutzler 6fdaf16dd0 ath79: add support for Ubiquiti Picostation M (XM)
This adds support for the Ubiquiti Picostation M (XM), which has the
same board/LEDs as the Bullet M XM, but different case and antennas.

Specifications:
- AR7241 SoC @ 400 MHz
- 32 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- External antenna: 5 dBi (USA), 2 dBi (EU)
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB

Flashing via WebUI:
  Upload the factory image via the stock firmware web UI.

  Attention: airOS firmware versions >= 5.6 have a new bootloader with
  an incompatible partition table!

  Please downgrade to <= 5.5 _before_ flashing OpenWrt!
  Refer to the device's Wiki page for further information.

Flashing via TFTP:
  Same procedure as other NanoStation M boards.

- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
  button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
  LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
  $ tftp 192.168.1.20
  tftp> bin
  tftp> trace
  tftp> put openwrt-ath79-generic-xxxxx-ubnt_picostation-m-squashfs-factory.bin

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-19 23:20:09 +01:00
Sven Roederer b56bcfe3be ath79: add support for Ubiquiti Nanostation Loco M (XM)
This adds support for the Ubiquiti Nanostation Loco M (XM), which
has the same board/LEDs as the Bullet M XM, but different case and
antennas.

Specifications:
- AR7241 SoC @ 400 MHz
- 32 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- NS Loco M2: built-in antenna: 8 dBi; AR9287
- NS Loco M5: built-in antenna: 13 dBi; 2T2R 5 GHz radio
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB

Flashing via WebUI:
  Upload the factory image via the stock firmware web UI.
  Note that only certain firmware versions accept unsigned
  images. Refer to the device's Wiki page for further information.

Flashing via TFTP:
  Same procedure as other NanoStation M boards.

- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
  button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
  LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
  $ tftp 192.168.1.20
  tftp> bin
  tftp> trace
  tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-squashfs-factory.bin

Tested on NanoStation Loco M2.

Signed-off-by: Sven Roederer <freifunk@it-solutions.geroedel.de>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-19 23:20:00 +01:00
Adrian Schmutzler 98fbf2edc0 ath79: move TPLINK_HWID/_HWREV to parent for tplink-safeloader
Several devices with tplink-safeloader contain default values (0x0)
for TPLINK_HWID and TPLINK_HWREV in their device definitions.
Move those to common tplink-safeloader definition so they do not
have to be repeated each time.

While at it, set default value for tplink-v1 and tplink-v2 as well.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-19 23:19:43 +01:00
David Bauer d2b8ccb1c0 ath79: add support for Siemens WS-AP3610
Hardware
--------
SoC:  Atheros AR7161
RAM:  Samsung K4H511638D-UCCC
      2x 64M DDR1
SPI:  Micron M25P128 (16M)
WiFi: Atheros AR9160 bgn
      Atheros AR9160 an
ETH:  Broadcom BCM5481
LED:  Power (Green/Red)
      ETH (Green / Blue / Yellow)
          (PHY-controlled)
      WiFi 5 (Green / Blue)
      WiFi 2 (Green / Blue)
BTN:  Reset

Serial: Cisco-Style RJ45 - 115200 8N1

Installation
------------

1. Download the OpenWrt initramfs-image. Place it into a TFTP server
   root directory and rename it to 1401A8C0.img. Configure the TFTP
   server to listen at 192.168.1.66/24.

2. Connect the TFTP server to the access point.

3. Connect to the serial console of the access point. Attach power and
   interrupt the boot procedure when prompted (bootdelay is 1 second).

4. Configure the U-Boot environment for booting OpenWrt from Ram and
   flash:

   $ setenv boot_openwrt 'setenv bootargs; bootm 0xbf080000'
   $ setenv ramboot_openwrt 'setenv serverip 192.168.1.66;
     tftpboot; bootm'
   $ saveenv

5. Load OpenWrt into memory:

   $ run ramboot_openwrt

   Wait for the image to boot.

6. Transfer the OpenWrt sysupgrade image to the device. Write the image
   to flash using sysupgrade:

   $ sysupgrade -n /path/to/openwrt-sysuograde.bin

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-02-16 15:36:29 +01:00
Adrian Schmutzler fbd00bb8d4 ath79: add support for TP-Link TL-WR940N v6
The TL-WR940N v6 is similar to v3/v4, it just has different
LEDs and MAC address assignment.

Specification:
- 750 MHz CPU
- 32 MB of RAM
- 4 MB of FLASH
- 2.4 GHz WiFi
- 4x 10/100 Mbps Ethernet

The use of LEDs is based on ar71xx, so blue LED is used for WAN
and orange LED for diag (boot/failsafe/etc.).

Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.

Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to
   wr940nv6_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Thanks to Manuel Kock for reviewing and testing this patch.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Manuel Kock <github.web@manu.li>
2020-02-13 17:33:20 +01:00
Adrian Schmutzler 49ff00db34 ath79: enable forceless sysupgrade from ar71xx on fritz300e
This adds the ar71xx board name to the SUPPORTED_DEVICES on ath79,
so forceless sysupgrade on this device becomes possible.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-13 17:33:20 +01:00
Christian Buschau fb99ac6807 ath79: add support for TP-Link TL-WA830RE v1
This ports support for the TL-WA830RE v1 range extender from ar71xx to
ath79.

Specifications:
- SOC: Atheros AR7240
- CPU: 400MHz
- Flash: 4 MiB (Spansion S25FL032P)
- RAM: 32 MiB (Zentel A3S56D40FTP-G5)
- WLAN: Atheros AR9280 bgn 2x2
- Ethernet: 1 port (100M)

Flash instructions:
- install from u-boot with tftp (requires serial access)
  > setenv ipaddr a.b.c.d
  > setenv serverip e.f.g.h
  > tftpboot 0x80000000 \
      openwrt-ath79-tiny-tplink_tl-wa830re-v1-squashfs-factory.bin
  > erase 0x9f020000 +0x3c0000
  > cp.b 0x80000000 0x9f020000 0x3c0000
  > bootm 0x9f020000
- flash factory image from OEM WebUI
- sysupgrade from ar71xx image

The device seems to be a clone of the following devices not yet
added to ath79:
- tl-wa701nd-v1
- tl-wa730re-v1
- tl-wa801nd-v1
- tl-wa901nd-v1

Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
[make use of ar7240_tplink.dtsi, add note about clones]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-11 14:31:05 +01:00
August Huber ae61d21ca3 ath79: add support for COMFAST CF-E560AC
This commit adds support for the COMFAST CF-E560AC, an ap143 based
in-wall access point.

Specifications:
 - SoC: Qualcomm Atheros QCA9531
 - RAM: 128 MB DDR2 (Winbond W971GG6SB-25)
 - Storage: 16 MB NOR (Winbond 25Q128JVSO)
 - WAN: 1x 10/100 PoE ethernet (48v)
 - LAN: 4x 10/100 ethernet
 - WLAN1: QCA9531 - 802.11b/g/n - 2x SKY85303-21 FEM
 - WLAN2: QCA9886 - 802.11ac/n/a - 2x SKY85735-11 FEM
 - USB: one external USB2.0 port
 - UART: 3.3v, 2.54mm headers already populated on board
 - LED: 7x external
 - Button: 1x external
 - Boot: U-Boot 1.1.4 (pepe2k/u-boot_mod)

MAC addressing:

- stock
  LAN    *:40 (label)
  WAN    *:41
  5G     *:42
  2.4G   *:4a

- flash (art partition)
  0x0    *:40 (label)
  0x6    *:42
  0x1002 *:41
  0x5006 *:43

This device contains valid MAC addresses in art 0x0, 0x6, 0x1002 and
0x5006, however the vendor firmware only reads from art:0x0 for the LAN
interface and then increments in 02_network. They also jump 8 addresses
for the second wifi interface (2.4 GHz). This behavior has been duplicated
in the DTS and ath10k hotplug to align addresses with the vendor firmware
v2.6.0.

Recovery instructions:

This device contains built-in u-boot tftp recovery.

1. Configure PC with static IP 192.168.1.10/24 and tftp server.
2. Place desired image at /firmware_auto.bin at tftp root.
3. Connect device to PC, and power on.
4. Device will fetch flash from tftp, flash and reboot into new image.

Signed-off-by: August Huber <auh@google.com>
[move jtag_disable_pins, remove unnecessary statuses in DTS, remove
duplicate entry in 11-ath10k-caldata, remove hub_port0 label in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-03 16:18:08 +01:00
Michal Cieslakiewicz 3b99d67639 ath79: WNDR3700 v2: add dash before version in device name
Adapt Netgear WNDR3700v2 device identification string to ath79 naming
scheme by changing from 'wndr3700v2' to 'wndr3700-v2' (affects config,
makefile, init scripts and device tree definition).

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2020-02-03 11:28:05 +01:00
Adrian Schmutzler 4897bf0ca5 ath79: add common definition for Device/tplink-v2
This adds a shared definition Device/tplink-v2 to common-tp-link.mk.
Though currently only one device in ath79 uses it, putting it in
the common file seems more organized. The definitions are based
on the implementation in ramips target, where a lot of devices
is using tplink-v2-* commands already.

The '-V "ver. 2.0"' suffix for Archer D50 v1 can be removed because
it's default in Build/tplink-v2-image anyway.

While at it, add TPLINK_HWREVADD and TPLINK_HVERSION to DEVICE_VARS,
which seems to have been overlooked when adding Archer D50 v1.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-02 14:01:59 +01:00
Adrian Schmutzler 8a6994eb03 ath79: rename tplink-loader-okli to tplink-safeloader-okli
This renames Device/tplink-loader-okli to Device/tplink-safeloader-okli
since the latter more accurately describes the combination of
tplink-safeloader and loader-okli use there. The old version might
be confused with other uses of the okli loader.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-02 13:41:20 +01:00
Adrian Schmutzler 9c37c5ef2f ath79: rename Device/tplink to Device/tplink-v1
As we have tplink-v2-header and tplink-v2-image recipes as well,
this patch renames the Device/tplink definition to Device/tplink-v1,
as it's using the tplink-v1-* commands. This should provide easier
distinction in the future.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-02 13:40:08 +01:00
Roger Pueyo Centelles 633c4304ad ath79: add support for Ubiquiti NanoStation Loco M (XW)
This commit adds support for the NanoStation Loco M2/M5 XW devices
on the ath79 target (support was long ago available on ar71xx).

Specifications:

 - AR9342 SoC @ 535 MHz
 - 64 MB RAM
 - 8 MB SPI flash
 - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
 - AR8032 switch
 - 2T2R 5 GHz radio, 22 dBm
 - 13 dBi built-in antenna
 - POWER/LAN green LEDs
 - 4x RSSI LEDs (red, orange, green, green)
 - UART (115200 8N1) on PCB

Flashing via TFTP:

 - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
   button on the device or on the PoE supply pressed
 - Power on the device via PoE (keep reset button pressed)
 - Keep pressing until LEDs flash alternatively LED1+LED3 =>
   LED2+LED4 => LED1+LED3, etc.
 - Release reset button
 - The device starts a TFTP server at 192.168.1.20
 - Set a static IP on the computer (e.g., 192.168.1.21/24)
 - Upload via tftp the factory image:
   $ tftp 192.168.1.20
   tftp> bin
   tftp> trace
   tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-xw-squashfs-factory.bin

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2020-01-31 17:24:31 +01:00
Adrian Schmutzler b4d3110ac1 ath79: add support for GL.iNet 6408/6416 (GL.iNet V1)
This ports the GL.iNet 6408/6416 from ar71xx.

The GL-Connect GL.iNet v1 routers are basically a TP-Link TL-WR710N with
more DRAM/Flash and console/GPIO header in the same small form-factor.

Specifications:
 - SoC: Atheros AR9331
 - CPU: 400 MHz
 - Flash: 8/16 MiB
 - RAM: 64 MiB
 - WiFi: 2.4 GHz b/g/n (SoC)
 - Ethernet: 2x 100M ports (LAN/WAN)
 - USB: 1x 2.0

The difference between 6408 and 6416 is just the flash size. It looks like
only the 16 MiB version has been advertised, while the 6408 is a modified
version. There are also 1-port versions sold by third parties.

Installation:
Install the sysupgrade image via stock firmware GUI or upload it via uboot
(web-based). The device will be available at 192.168.1.1.

Attention: In ar71xx, the same board name is used for both flash versions.
So, please make sure you flash the correct ath79 image when upgrading.

This has been device-tested on a GL.iNet 6416.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-29 18:56:04 +01:00
Adrian Schmutzler 07ce940b77 ath79: fix SUPPORTED_DEVICES not matching ar71xx board names
Based on a script for comparison, this fixes (hopefully) all errors
in SUPPORTED_DEVICES for ar71xx->ath79 upgrade.

Devices where old string is removed as the device does not exist
in ar71xx:
- dlink_dir-859-a1
- tplink_archer-a7-v5
- tplink_cpe510-v3

Devices where string is changed because it did not match the board
name in ar71xx:
- tplink_tl-mr3220-v1
- tplink_tl-mr3420-v1
- tplink_tl-wr2543-v1
- tplink_tl-wr741nd-v4
- tplink_tl-wr841-v7
- ubnt_unifiac-mesh
- ubnt_unifiac-mesh-pro
- ubnt_unifiac-pro

For this device, the correct string could not be found, but we could
not determine the correct one. Thus, the string is removed for now:
- tplink_tl-wr740n-v4

The script for checking this is quite simple (note that newer
entries, i.e. ath79->ath79 upgrade, are displayed as missing):

  newpath=target/linux/ath79/image/
  oldpath=target/linux/ar71xx/base-files/lib/ar71xx.sh

  for s in $(grep -roh "SUPPORTED_DEVICES.*" $newpath | sed 's/SUPPORTED_DEVICES *.= *//'); do
    found="Missing"
    grep -q -r "\"$s\"" $oldpath && found="Found"
    echo "$s: $found."
  done

The errors might be filtered by appending 'grep "Missing"' to the script.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-23 16:09:58 +01:00
Adrian Schmutzler 071a637276 ath79: move lzma-loader to the end of available RAM
In certain cases, the uncompressed initramfs image will overwrite
the lzma-loader, which is currently only 10 MB away from kernel image
start. To prevent this, change LZMA_TEXT_START to 24 MB, so loader
and compressed image have 8 MB at the end of RAM and uncompressed
image has 24 MB available.

This is only enabled for ath79 at the moment, as there we can be sure
that all devices have 32+ MB RAM and TARGET_INITRAMFS_COMPRESSION_LZMA
is not enabled there.

Despite, since lzma-loader is currently build specifically for ath79
anyway, there is no need to re-specify LOADADDR and LZMA_TEXT_START
in image/Makefile, so the values are set directly in
image/lzma-loader/Makefile and the overwrite in image/Makefile is
removed.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-01-23 15:28:03 +01:00
Roger Pueyo Centelles 6aaa5ce2c5 ath79: add support for MikroTik RouterBOARD wAP G-5HacT2HnD
This commit adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD
(wAP AC), a small weatherproof dual band, dual-radio 802.11ac
wireless AP with integrated omnidirectional anntennae and one
10/100/1000 Mbps Ethernet port.

See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info.

Specifications:
 - SoC: Qualcomm Atheros QCA9556
 - RAM: 64 MB
 - Storage: 16 MB NOR
 - Wireless:
   · Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae
   · Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae
 - Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port,
   passive PoE in

Working:
 - Board/system detection
 - Sysupgrade
 - Serial console
 - Ethernet
 - 2.4 GHz radio
 - 5 GHz radio and LED
 - Reset button

Not working/Unsupported:
 - 2.4 GHz LED
 - AP/CAP LED
 - ZT2046Q SPI temperature and voltage sensor

This adds the basic features for supporting MikroTik devices:
 - a common recipe for mikrotik images in common-mikrotik.mk
 - support for minor (MikroTik NOR) split firmware (only for
   generic subtarget so far)

Acknowledgments: Robert Marko <robimarko@gmail.com>
                 Andrew Cameron <apcameron@softhome.net>
                 Koen Vandeputte <koen.vandeputte@ncentric.com>
                 Chuanhong Guo <gch981213@gmail.com>

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-01-23 15:28:03 +01:00
Adrian Schmutzler a66a1eb9c5 ath79: add support for TP-Link TL-WA850RE v2
TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.

Short specification:

- 550/391/195 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x internal antennas (embedded on PCB)
- 9x LED (all can be turned off with GPIO15), 2x button
- UART (J3) header on PCB

Flash instruction: use "factory" image directly in vendor GUI.

Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.

You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin

Stock firmware uses label MAC address for WiFi and same with local
bit set for ethernet. Since this is difficult to reproduce with
the toolset of OpenWrt, we just keep both ethernet and WiFi to
the same address here.

This is the first tiny device with tplink-safeloader in ath79.
Firmware partition is only 3648k and thus even smaller than for
the tplink-4m(lzma) devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-22 23:52:51 +01:00
Adrian Schmutzler 6eaea3a8ba ath79: add support for TP-Link TL-WA850RE v1
This ports support for the TL-WA850RE v1 range extender from ar71xx
to ath79.

Specifications:
  Board: AP123 / AR9341 rev. 3
  Flash/RAM: 4/32 MiB
  CPU: 535 MHz
  WiFi: 2.4 GHz b/g/n
  Ethernet: 1 port (100M)

Flashing instructions:
Upload the factory image via the vendor firmware upgrade option.

Recovery:
Note that this device does not provide TFTP via ethernet like many
other TP-Link devices do. You will have to open the case if you
require recovery beyond failsafe.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-22 17:18:55 +01:00
Adrian Schmutzler 111a7a3d01 ath79: remove usused TPLINK_BOARD_NAME variable for DEVICE_VARS
TPLINK_BOARD_NAME has been renamed to TPLINK_BOARD_ID a long time
ago (7d6c63d87542: "build: rename TPLINK_BOARD_NAME to
TPLINK_BOARD_ID" for ar71xx), and before introducing ath79 target
at all.

TPLINK_BOARD_NAME seems to have been introduced into ath79 target
only by mistake. It has never been used. Remove it.

Fixes: 53c474abbd ("ath79: add new OF only target for QCA MIPS silicon")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-21 18:08:19 +01:00
Enrico Mioso b99b60b2f1 ath79: add support for TP-Link TL-MR6400
This device is an LTE router supported in ar71xx so far.
As per original commit, hardware specifications (v1.0 EU):
- SoC: QCA9531
- Flash: Winbond W25Q64FV (8MiB)
- RAM: EtronTech EM6AB160TSE-5G (64MiB)
- Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
- Ethernet: 2NIC (3x100M + 1x100M)
- WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
- Power: DC 12V 1A

Flashing instructions:
You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin
on 192.168.0.66/24, connect to any ethernet port and power on device while
holding the reset button). Flashing via OEM web interface does not work.

Known issues:
- LTE module does not always come up during boot (showing USB enumeration errors). Similar behavior has been reported at least from one user for ar71xx, too. Turning USB off and on again will serve as a workaround.
- eth0 (LAN) always shows carrier as 1 even if no cable is plugged in (this works "correctly" on ar71xx)

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
[several adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Filip Moc <lede@moc6.cz>
2020-01-21 14:15:48 +01:00
Michal Cieslakiewicz 0d28e5d644 ath79: fix SUPPORTED_DEVICES for WNDR4300 and WNDR3700v4
Kernel partition increase to 4 MiBs for Netgear WNDR3700v4 and WNDR4300
routers breaks sysupgrade image compatibility with ar71xx builds.
Therefore, SUPPORTED_DEVICES variable has to be removed for both devices
from target makefile.

Reported-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2020-01-21 00:29:25 +01:00
Michal Cieslakiewicz a736f39432 ath79: add support for Netgear WNDR4500 v3
This patch introduces support for Netgear WNDR4500v3. Router
is very similar to WNDR4300v2 and is based on the same PCB.

Information gathered from various Internet sources (including
https://patchwork.ozlabs.org/patch/809227/) shows following
differences to WNDR4300v2:

 * two USB 2.0 ports with separate LEDs
 * USB LEDs soldered to secondary pads
 * WPS and RFKILL buttons soldered to secondary pads
 * described as N900 device with 3x3:3 MIMO for 2.4GHz radio
 * power supply requirement is DC 12V 2.5A
 * vendor HW ID suffix differs in one digit
 * bigger chassis

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2020-01-15 20:56:05 +01:00
Michal Cieslakiewicz 37a36a588a ath79: add support for Netgear WNDR4300 v2
This patch introduces support for Netgear WNDR4300v2.

Specification
=============
  * Description: Netgear WNDR4300 v2
  * Loader: U-boot
  * SOC: Qualcomm Atheros QCA9563 (775 MHz)
  * RAM: 128 MiB
  * Flash: 2 MiB SPI-NOR + 128 MiB SPI-NAND
	- NOR: U-boot binary: 256 KiB
	- NOR: U-boot environment: 64 KiB
	- NOR: ART Backup: 64 KiB
 	- NOR: Config: 64 KiB
	- NOR: Traffic Meter: 64 KiB
	- NOR: POT: 64 KiB
	- NOR: Reserved: 1408 KiB
	- NOR: ART: 64 KiB
	- NAND: Firmware: 25600 KiB (see notes for OpenWrt)
	- NAND: Language: 2048 KiB
	- NAND: mtdoops Crash Dump: 128 KiB
	- NAND: Reserved: 103296 KiB
  * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8337)
  * Wireless:
	- 2.4 GHz b/g/n (internal)
	- 5 GHz a/n (AR9580)
  * USB: yes, 1 x USB 2.0
  * Buttons:
	- Reset
	- WiFi (rfkill)
	- WPS
  * LEDs:
	- Power (amber/green)
	- WAN (amber/green)
	- WLAN 2G (green)
	- WLAN 5G (blue)
	- 4 x LAN (amber/green)
	- USB (green)
	- WPS (green)
  * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
  * Power supply: DC 12V 1.5A
  * MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2

Important Notes
===============
0. NOR Flash (2 MiB) is not touched by OpenWrt installation.
1. NAND Flash (128 MiB) layout under OpenWrt is changed as follows:
   all space is split between 4 MiB kernel and 124 MiB UBI areas;
   vendor partitions (language and mtdoops) are removed; kernel space
   size can be further expanded if needed; maximum image size is set
   to 25600k for compatibility reasons and can also be increased.
2. CPU clock is 775 MHz, not 750 MHz.
3. 5 GHz wireless radio chip is Atheros AR9580-AR1A with bogus PCI
   device ID 0xabcd. For ath9k driver to load successfully, this is
   overriden in DTS with correct value for this chip, 0x0033.
4. RFKILL button is wired to AR9580 pin 9 which is normally disabled
   by chip definition in ath9k code (0x0000F4FF gpio mask). Therefore
   'qca,gpio-mask=<0xf6ff>' hack must be used for button to work
   properly.
5. USB port is always on, no GPIO for 5V power control has been
   identified.

Installation
============
  * TFTP recovery
  * TFTP via U-boot prompt
  * sysupgrade
  * Web interface

Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_nand=y
CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr4300-v2=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2020-01-15 20:55:56 +01:00
Michal Cieslakiewicz 4e6af8b9ef ath79: WNDR4300: increase kernel partition to 4M
Increase kernel partition from 2 MiB to 4 MiB for Netgear WNDR routers
with NAND flash. Change affects following devices:
 * Netgear WNDR3700 v4
 * Netgear WNDR4300

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2020-01-15 20:55:42 +01:00
David Bauer c9ac7b1729 ath79: add support for D-Link DIR-505
This commit adds support for the D-Link DIR-505, previously supported in
ar71xx.

Hardware
--------
SoC:   Atheros AR9330
FLASH: 8M SPI-NOR
RAM:   64M
WIFI:  1T1R 1SS Atheros AR9330
LED:   Power green, Status red
BTN:   WPS, Reset

Installation
------------
Currently, installation is only possible by sysupgrading from an earlier
OpenWrt version, U-Boot TFTP or a modded U-Boot. I do not have the
original bootloader from D-Link on my device anymore, so i cannot test
the factory image.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-01-15 20:38:46 +01:00
Jeff Kletsky e96bfaedf3 ath79: GL-AR750S (NOR/NAND): limit factory.img kernel size to 2 MB
The present U-Boot for GL-AR750S has a limit of 2 MB for kernel size.
While sysupgrade can manage kernels up to the present limit of 4 MB,
directly flashing a factory.img with a kernel size greater than 2 MB
through U-Boot will result in an unbootable device.

This commit uses the newly-introduced check-kernel-size build
operation to prevent the output of factory.img when the kernel
exceeds 2 MB in size, yet permits output of sysupgrade.img
as long as the kernel is within KERNEL_SIZE := 4096k

Cc: Chuanhong Guo <gch981213@gmail.com>

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2020-01-15 20:06:02 +01:00
Tomasz Maciej Nowak 2248df303d ath79: wlr-7100: use ath10k-ct smallbuffers package variant
The memory hacks got removed from ath10k with 1e27bef ("mac80211: remove
ath10k_pci memory hacks"). As this device has low amount of RAM, switch
to ath-10k-ct small buffers variant, to avoid the OOM Reaper.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-01-15 19:53:49 +01:00
Tobias Schramm 66eb88edb6 ath79: add support for Ubiquiti EdgeSwitch/ToughSwitch 5XP
The Ubiquiti ToughSwitch 5XP is a 5-port PoE Gigabit switch with a single
Fast-Ethernet management port. It supports both 24V passive PoE out on all
five ports.

Flash:    8 MB
RAM:      64 MB
SoC:      AR7242
Switch:   ar8327
USB:      1x USB 2.0
Ethernet: 5x GbE, 1x FE

Installation of the firmware is possible either via serial + tftpboot or
the factory firmware update function via webinterface.

By default the single Fast-Ethernet port labeled "MGMT" is configured
as the WAN port. Thus access to the device is only possible via the
five switch ports.

Serial: 3v3 115200 8n1

The serial header is located in the lower left corner of the switches PCB:

```
|
|
|
| o
| o RX
| o TX
| o GND
|
|
++  +-++-+  ++  ++  +
+--+ ++ +--++--++--+
```

Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
[remove ubnt,sw compatible - fix spelling - wrap commit message -
remove superfluous phy-mode property]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-01-14 09:38:32 +01:00
Tobias Schramm b6946542f8 ath79: add support for Ubiquiti ToughSwitch/EdgeSwitch 8XP
Flash:    8 MB
RAM:      64 MB
SoC:      AR7242
Switch:   bcm53128
USB:      1x USB 2.0
Ethernet: 8x GbE, 1x FE

The Ubiquiti ToughSwitch 8XP is a 8-port PoE Gigabit switch with a single
Fast-Ethernet management port. It supports both 24V passive PoE and 48V
802.11af/at PoE out on all eight ports.

By default the single Fast-Ethernet port labeled "MGMT" is configured as the
WAN port. Thus access to the device is only possible via the eight switch
ports.

Installation of the firware is possible either via serial + tftpboot or
the factory firmware update function via webinterface.

Serial: 3v3 115200 8n1

The serial header is located in the lower left corner of the switches PCB:

|
|
|
| o
| o RX
| o TX
| o GND
|
|
++  +-++-+  ++  ++  +
 +--+ ++ +--++--++--+

Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
[fix whitespace issue]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-01-12 14:12:50 +01:00
Tobias Schramm 7d97fdf5ef ath79: add support for Ubiquiti SW devices
SW devices are Ubiquit ToughSwitch and EdgeSwitch series devices.
Hardware-wise they are very similar to the XM device series.

Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2020-01-12 14:12:50 +01:00
Chuanhong Guo b97247c2e9 ath79: gl-ar750s: reduce kernel size to 2M in image Makefile
u-boot splits nand factory firmware at 2M offset, flash the first
part as kernel into spi nor and the other part as ubi into nand
flash. With previous commit increasing kernel size to 4M, generated
factory firmware is broken because ubi is at 4M offset.

This commit reduces kernel size definition to 2M in image Makefile,
producing proper factory image. Partition size in dts is kept
unchanged so that sysupgrade to a firmware with 2M+ kernel still
works.

Fixes: b496a2294c ("ath79: GL-AR750S: provide NAND support; increase kernel to 4 MB")
Reported-by: Jeff Kletsky <git-commits@allycomm.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-01-11 10:37:04 +08:00
Adrian Schmutzler df41cc7445 ath79: remove unused Build/mktplinkfw-combined
Build/mktplinkfw-combined is not used anywhere, so remove it.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-08 16:17:58 +01:00
Adrian Schmutzler 9b0e8d0aa4 treewide: move mktplinkfw to tplink-v1-image in image-commands.mk
This move the slightly different target-specific implementations of
mktplinkfw from the targets to include/image-commands.mk and renames
it to tplink-v1-image. Having a common version will increase
consistency between implementation and will complete the
tplink build command already present in the new location.

Due to the slight differences of the original implementations, this
also does some adjustments to the device build commands/variables.

This also moves rootfs_align as this is required as dependency.

Tested on:
- TL-WDR4300 v1 (ath79, factory)
- TL-WDR4900 v1 (mpc85xx, sysupgrade)
- RE210 v1 (ramips, see Tested-by)

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Christoph Krapp <achterin@googlemail.com>
2020-01-08 16:15:29 +01:00
Christoph Krapp 7bef62de79 ath79: use ath10k-ct-smallbuffers for TP-Link RE355/RE450 v1
Both devices are available in 64M and 128M RAM configurations but there
is no visial indication which configuration one might get.
So just to be sure we properly support both configurations switch to
kmod-atk10k-ct-smallbuffers.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2020-01-05 19:36:45 +01:00
Christian Mauderer 5e5e92b7c3 ath79: generate firmware image for aircube-isp
This adds a "factory" image for the aircube-isp devices. Note that the
firmware can't be uploaded without prior special preparation. For the
most recent instructions on how to do that, visit the OpenWRT wiki page
of the Ubiquiti airCube ISP for details:

https://openwrt.org/toh/ubiquiti/ubiquiti_aircube_isp

Current procedure:

With the original firmware 2.5.0 it is possible to upload and execute a
script via the configuration. To do that download and unpack the
original configuration, adapt uhttpd config to execute another lua
handler (placed in the config directory) and pack and upload it again.

The lua handler can call a script that mounts an overlayfs and modifies
the "fwupdate.real" binary so that an unsigned image is accepted. The
overlayfs is necessary because a security system (called tomoyo) doesn't
allow binaries in other locations than /sbin/fwupdate.real (and maybe
some more) to access the flash when executed via network.

A big thanks to Torvald Menningen (Snap) from the OpenWRT forum for
finding out how to patch the binary so that it accepts an unsigned
image.

The current step-by-step procedure is:

- Use a version 2.5.0 of the original firmware. This is important
  because a binary file will be modified.
- Download a configuration.
- Unpack it (it's just a tar gz file without an ending).
- Add the following to uhttpd:

``````
config 'uhttpd' 'other'
	list listen_http    0.0.0.0:8080
	list listen_http    [::]:8080
	option 'home'       '/tmp/persistent/config/patch/www'
	option lua_prefix   '/lua'
	option lua_handler  '/tmp/persistent/config/patch/handler.lua'
``````

- Create a `patch` subfolder.
- Create a `patch/www` subfolder.
- Create a `patch/handler.lua` with the following content:

``````
function handle_request(env)
    uhttpd.send("Status: 200 OK\r\n")
    uhttpd.send("Content-Type: text/plain\r\n\r\n")

    local command = "/bin/sh /tmp/persistent/config/patch/patch.sh 2>&1"

    local proc = assert(io.popen(command))
    for line in proc:lines() do
        uhttpd.send(line.."\r\n")
    end
    proc:close()
end
``````

- Create a `patch/patch.sh` with the following content:

``````
#!/bin/sh -x

set -e
set -u
set -x

UBNTBOX_PATCHED="/tmp/fwupdate.real"
MD5FILE="/tmp/patchmd5"

cat <<EOF > ${MD5FILE}
c33235322da5baca5a7b237c09bc8df1  /sbin/fwupdate.real
EOF

# check md5 of files that will be patched
if ! md5sum -c ${MD5FILE}
then
        echo "******** Error when checking files. Refuse to do anything. ********"
        exit 0
fi

# prepare some overlay functionality
LOWERDIR="/tmp/lower_root"
mkdir -p ${LOWERDIR}
mount -t squashfs -oro /dev/mtdblock3 ${LOWERDIR}
overlay_some_path()
{
        PATH_TO_OVERLAY=$1
        ALIAS=$2
        UPPERDIR="/tmp/over_${ALIAS}"
        WORKDIR="/tmp/over_${ALIAS}_work"

        mkdir -p ${UPPERDIR}
        mkdir -p ${WORKDIR}

        mount -t overlay -o lowerdir=${LOWERDIR}${PATH_TO_OVERLAY},upperdir=${UPPERDIR},workdir=${WORKDIR} overlay ${PATH_TO_OVERLAY}
}

# patch the ubntbox binary.
overlay_some_path "/sbin" "sbin"
echo -en '\x10' | dd of=/sbin/fwupdate.real conv=notrunc bs=1 count=1 seek=24598

echo "******** Done ********"
``````

- Repack the configuration.
- Upload it via the normal web interface.
- Wait about a minute. The webserver should restart.
- Now there is a second web server at port 8080 which can call the lua
  script. Visit the page with a web browser. Link is for example
  http://192.168.1.1:8080/lua
- You should see the output of the script with a "*** Done ***" at the
  end. Note that the patches are not permanent. If you restart the
  router you have to re-visit the link (but not re-upload the config).
- Now you can upload an unsigned binary via the normal web interface.

Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
2019-12-31 01:42:13 +01:00
Paul Fertser 3e51cb7820 ath79: tp-link: use ath10k-ct-smallbuffers for 64 MiB devices
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2019-12-25 11:59:16 +01:00
Paul Fertser db992e7b53 ath79: use ath10k-ct-smallbuffers for 64 MiB devices
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2019-12-24 00:57:56 +01:00
Hauke Mehrtens b0b1d4aaf0 ath79: Do not build dlink_dir-615-e4 by default
The factory image for the dlink_dir-615-e4 is getting too big which makes
the full ath79 tiny build fail, deactivate it by default.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-12-23 15:24:43 +01:00
Adrian Schmutzler 95030ac0b6 ath79: rename ATH_SOC to SOC
This replaces ATH_SOC by the newly introduced common SOC device
variable.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-20 01:12:42 +01:00
Adrian Schmutzler 0757f7fedc ath79: harmonize line breaks in image Makefiles
This harmonizes the line wrapping in image Makefile device
definitions, as those are frequently copy-pasted and are a common
subject of review comments. Having the treatment unifying should
reduce the cases where adjustment is necessary afterwards.

Harmonization is achieved by consistently (read "strictly")
applying certain rules:
- Never put more than 80 characters into one line
- Fill lines up (do not break after 40 chars because of ...)
- Use one tab for indent after wrapping by "\"
- Only break after pipe "|" for IMAGE variables

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-20 00:29:05 +01:00
Paul Fertser b14e529dd7 ath79: add D-Link DIR-615 E4
Specifications:

- FCC ID: KA2IR615E3
- SoC: MIPS32 24K 400 MHz Atheros AR7240
- RAM: 32 MiB DDR SDRAM ESMT M13S2561616A-5T
- Flash: 4 MiB NOR SPI Macronix MX25L3208E
- Wireless: AR9287 2.4 GHz 802.11n 2T2R, 2x RP-SMA connectors
- Ethernet: 5x 100BASE-TX Fast Ethernet
- LEDs: 9x GPIO, 1x ath9k
- Buttons: 2x tactile switches
- UART: 3.3 V, 115200 8n1
- USB: simple hardware modification required, 1x USB 1.1 Full Speed

Partitioning notes:

Vendor firmware (based on CameoAP99) defines two additional partitions:
"mac" @0x3b0000, size 0x10000 and "lp" @0x3c0000, size 0x30000.

The "mac" partition stores LAN MAC address and hardware board name.
However, the vendor firmware uses addresses from "nvram" partition, and
the board name is used only for informational purposes in the Web
interface (included in the pages' header), not affecting the firmware
image check.

The "lp" partition is supposed to contain a "language pack" (which can
be used to add an additional language support to the Web interface) and
is flashed separately, using the vendor firmware upgrade page.

Since these partitions are absolutely useless for OpenWrt and
overwriting them doesn't prevent downgrading to obsolete vendor
firmware, this patch appends the valueable space to "firmware".

Installation instructions:

- Upgrade from OpenWrt ar71xx with "sysupgrade -f -n"
or
- Upload as a firmware update via the vendor Web-interface
or
- Connect UART and use "loady" to upload and run OpenWrt initramfs
  image, then sysupgrade from it (TFTP client doesn't work)
or
- Before powering up hold "reset" button and keep it pressed for about
  15 seconds after, then access fail safe Web server on 192.168.0.1 (the
  old uIP TCP/IP protocol stack is not compatible with modern Linux, the
  kernel, so you'll need to use some other OS to do this). Can be
  performed without a Web-browser too:
    curl http://192.168.0.1/cgi/index \
      -F Send=@openwrt-ath79-tiny-dlink_dir-615-e4-squashfs-factory.bin

Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2019-12-19 22:41:57 +01:00
Lech Perczak 60de1fdbb4 ath79: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.

Specification:

- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
  resitors are missing on TX/RX lines)
- 1x micro USB (for power only)

Flash instructions:

Use "factory" image under vendor GUI.

Recovery instructions:

This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
   to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
   and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.

MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label

Root access over serial line in vendor firmware: root/sohoadmin.

Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove size-cells from gpio-export]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-19 15:40:40 +01:00
Adrian Schmutzler c642a97aa6 ath79: add support for TP-Link TL-WDR4300 v1 (IL)
The TL-WDR4300 v1 sold in Israel has a different TPLINK_HWID.

Thanks to Josh4300 for testing on device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 14:42:05 +01:00
Adrian Schmutzler 8e91b18ab7 ath79: redistribute UBNT variables in Ubiquiti image Makefile
The variables UBNT_BOARD and UBNT_VERSION are defined in the parent
Device/ubnt definition and then overwritten for most of the derived
platform definitions (e.g. Device/ubnt-wa).

Since this mixed use of inheritance and overwriting can be misleading,
this moves the variables to the platform-based definitions.

While at it, reorder the definitions to have order consistent, too.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:18:01 +01:00
Stijn Tintel 157e17e985 ath79: add support for Ubiquiti LiteBeam AC Gen2
Hardware:
* SoC: Atheros AR9342-BL1A
* RAM: 64MB DDR2 (Winbond W9751G6KB-25)
* Flash: 16MB SPI NOR (Macronix MX25L12835FZ2I-10G)
* Ethernet: 1x 10/100/1000 Mbps (Atheros AR8035-A) with 24V PoE support
* Wifi 2.4GHz: Atheros AR9340 v2
* WiFi 5GHz: Ubiquiti U-AME-G1-BR4A (rebranded QCA988X v2)
* LEDs: 1x Power, 1x Ethernet
* Buttons: 1x Reset
* UART: 1x TTL 115200n8, 3.3V RX TX GND, 3.3V pin closest to RJ45 port

The LEDs do not seem to be connected to any GPIO, so there is currently
no way to control them.

Installation via U-Boot, TFTP and serial console:
* Configure your TFTP server with IP 192.168.1.254
* Connect serial console and power up the device
* Hit any key to stop autoboot
* tftpboot 0x81000000 openwrt-ath79-generic-ubnt_litebeam-ac-gen2-initramfs-kernel.bin
* bootm 0x81000000
* copy openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin
  to /tmp
* sysupgrade /tmp/openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-04 23:17:41 +02:00
Stijn Tintel db26f53bb3 ath79: drop IMAGE/factory.bin from ubnt-wa devices
The sysupgrade image contains OpenWrt specific metadata. Having this
metadata in the factory images makes no sense. Drop IMAGE/factory.bin
from Device/ubnt-wa and use the default from Device/ubnt instead.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-04 23:17:41 +02:00