Commit Graph

7 Commits (99835e09992bb411519fda1f8d16a6d07df7f598)

Author SHA1 Message Date
Jeff Kletsky 819e7946b0 ipq40xx: Add support for Linksys EA8300 (Dallas)
The Linksys EA8300 is based on QCA4019 and QCA9888 and provides three,
independent radios. NAND provides two, alternate kernel/firmware
images with fail-over provided by the OEM U-Boot.

Installation:

  "Factory" images may be installed directly through the OEM GUI.

Hardware Highlights:

  * IPQ4019 at 717 MHz (4 CPUs)
  * 256 MB NAND (Winbond W29N02GV, 8-bit parallel)
  * 256 MB RAM
  * Three, fully-functional radios; `iw phy` reports (FCC/US, -CT):
      * 2.4 GHz radio at 30 dBm
      * 5 GHz radio on ch. 36-64 at 23 dBm
      * 5 GHz radio on ch. 100-144 at 23 dBm (DFS), 149-165 at 30 dBm
      #{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1
      * All two-stream, MCS 0-9
  * 4x GigE LAN, 1x GigE Internet Ethernet jacks with port lights
  * USB3, single port on rear with LED
  * WPS and reset buttons
  * Four status lights on top
  * Serial pads internal (unpopulated)

  "Linksys Dallas WiFi AP router based on Qualcomm AP DK07.1-c1"

Implementation Notes:

  The OEM flash layout is preserved at this time with 3 MB kernel and
  ~69 MB UBIFS for each firmware version. The sysdiag (1 MB) and
  syscfg (56 MB) partitions are untouched, available as read-only.

Serial Connectivity:

  Serial connectivity is *not* required to flash.

  Serial may be accessed by opening the device and connecting
  a 3.3-V adapter using 115200, 8n1. U-Boot access is good,
  including the ability to load images over TFTP and
  either run or flash them.

  Looking at the top of the board, from the front of the unit,
  J3 can be found on the right edge of the board, near the rear

      |
   J3 |
  |-| |
  |O| | (3.3V seen, open-circuit)
  |O| | TXD
  |O| | RXD
  |O| |
  |O| | GND
  |-| |
      |

Unimplemented:

    * serial1 "ttyQHS0" (serial0 works as console)
    * Bluetooth; Qualcomm CSR8811 (potentially conected to serial1)

Other Notes:

    https://wikidevi.com/wiki/Linksys_EA8300 states

        FCC docs also cover the Linksys EA8250. According to the
	RF Test Report BT BR+EDR, "All models are identical except
	for the EA8300 supports 256QAM and the EA8250 disable 256QAM."

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-05-18 13:43:54 +02:00
Piotr Dymacz 9bf63d0339 uboot-envtools: add support for ALFA Network AP120C-AC
While at it, fix alphabetical order.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-02-26 00:16:22 +01:00
Oever González ad3e667539 uboot-envtools: add support for Linksys EA6350v3
This commit adds support for the Linksys EA6350v3 device in the ipq40xx
target.

This is needed for uboot-envtools to access the environment. Without this
patch, the Linksys EA6350v3 will not be able to access the uboot
environment. As a side effect, the feature auto_recovery will make the
device unstable by switching between the latest and the current firmware.

Signed-off-by: Ryan Pannell <ryan@osukl.com>
Signed-off-by: Oever González <notengobattery@gmail.com>
2019-01-26 21:43:04 +01:00
Ibrahim Tachijian eb054714b0 uboot-envtools: ipq40xx: Configuration for GL.iNet GL-B1300
This commit adds the nescessary settings to allow reading the uboot environment variables on the GL.iNet GL-B1300 board.

Signed-off-by: Ibrahim Tachijian <barhom@netsat.se>
2019-01-02 22:24:49 +01:00
Christian Lamparter 82618062cf ipq40xx: add support for the ZyXEL NBG6617
This patch adds support for ZyXEL NBG6617

Hardware highlights:

SOC:    IPQ4018 / QCA Dakota
CPU:    Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:   256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR:    32 MiB Macronix MX25L25635F
ETH:    Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB:    1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1:  Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:  Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:  RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS:   Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS

Serial:
	WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
	The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
	pre-soldered. Pinout:
	  1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX

first install / debricking / restore stock:
 0. Have a PC running a tftp-server @ 192.168.1.99/24
 1. connect the PC to any LAN-Ports
 2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
    into the tftp-server root directory and rename it to just "ras.bin".
 3. power-cycle the router and hold down the the WPS button (for 30sek)
 4. Wait (for a long time - the serial console provides some progress
    reports. The u-boot says it best: "Please be patient".
 5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
    flashes fast at the same time. You have to reboot the device and
    it should then come right up.

Installation via Web-UI:
 0. Connect a PC to the powered-on router. It will assign your PC a
    IP-address via DHCP
 1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
 2. Go to the "Expert Mode"
 3. Under "Maintenance", select "Firmware-Upgrade"
 4. Upload the OpenWRT factory image
 5. Wait for the Device to finish.
    It will reboot into OpenWRT without any additional actions needed.

To open the ZyXEL NBG6617:
 0. remove the four rubber feet glued on the backside
 1. remove the four philips screws and pry open the top cover
    (by applying force between the plastic top housing from the
    backside/lan-port side)

Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:

|   Hit any key to stop autoboot:  3

The user is then dropped to a locked shell.

|NBG6617> HELP
|ATEN    x[,y]     set BootExtension Debug Flag (y=password)
|ATSE    x         show the seed of password generator
|ATSH              dump manufacturer related data in ROM
|ATRT    [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO              boot up whole system
|ATUR    x         upgrade RAS image (filename)
|NBG6617>

In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!

First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.

|NBG6617> ATSE NBG6617
|012345678901

This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):

- tool.sh -
ror32() {
  echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -

|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711

copy and paste the result into the shell to unlock zloader.

|NBG6617> ATEN 1,0046B0017430

If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.

|NBG6617> ATGU
|NBG6617#

Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-26 08:57:26 +02:00
Sven Eckelmann 0b20490207 ipq40xx: add support for OpenMesh A62
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
  - QCA9888 hw2.0 (PCI)
  - requires special BDF in QCA9888/hw2.0/board-2.bin
    bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
  - triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
  - phy@mdio3:
    + Label: Ethernet 1
    + gmac0 (ethaddr) in original firmware
    + 802.3at POE+
  - phy@mdio4:
    + Label: Ethernet 2
    + gmac1 (eth1addr) in original firmware
    + 18-24V passive POE (mode B)
* powered only via POE

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

The initramfs image can be started using

  setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
  tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
  set fdt_high 0x85000000
  bootm 0x84000000

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-04-23 22:07:22 +02:00
John Crispin 54b275c8ed ipq40xx: add target
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: John Crispin <john@phrozen.org>
2018-03-14 19:04:50 +01:00