Move the devicetree source files to a kernel specific directory in
preparation of adding kernel 4.14 support.
Rename the subtarget kernel config files to match a specific kernel
version.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Annex A and Annex B version are using the same (old) userspace
boardname. Update the SUPPORTED_DEVICES to allow an update from lede-17.01.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use <manufacturer>_<modelname> as image name.
Use the BOARD_NAME variable to ensure that the former used boardname is
still used as the subdirectory name for the sysupgrade-tar image, to
not break sysupgrade from earlier versions.
While at it, normalise the image filenames by using only lower case
characters and bin as file extension for sysupgrade images.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the first compatible string as board name in userspace. Add the new
board name as well as the former used board name to the image metadata
to keep compatibilty with already deployed installations.
Don't add the former used boardname for boards which exists only in
master or evaluation boards.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This will avoid some conflicts when doing a git rebase or merge,
specially when adding support to a new device.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
[drop brcm47xx changes which rename the images]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Remove the WW suffix, everything without a region suffix is world wide
anyway.
While at it, normalise the image filenames by using only lower case
characters.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds all the board-specific values currently hardcoded
in mktplinkfw2.c back to the respective device declarations in the
makefiles.
The rationale is to avoid modifying the source code every time a
new board or board variant is added.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Install kmod-rt2800-pci instead of only the rt2x00 library.
Fixes missing wireless interface on AudioCodes AC-MP252.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Netgear DM200 is an inexpensive VDSL modem:
CPU: VRX220 MIPS 34Kc 5.6 @ 500Mhz
RAM: 64MiB
Flash: 8MiB
Ethernet: 1x100M
DSL: VDSL2+, ADSL2+
reset button, 3x bi-color LEDs
Serial port is 115200 baud, on the 4 pin header; pins from the bottom to
top are GND, RX, TX.
To upgrade from the vendor firmware, upload factory.img
The DM200 bootloader supports flashing over TFTP; hold the reset button
while powering on the device, and wait for the power light to start
flashing green before releasing. The device is now listening on
192.168.0.1/24, and can be sent a factory.img or a netgear image with a
TFTP put.
Once the image is loaded, it will be written to the flash, and the
device will reboot; this will take a few minutes.
Thanks to Edward O'Callaghan and Baptiste Jonglez, who implemented their
own ports for this device and provided valuable feedback.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
The Netgear UI in basic mode refuses the upgrade file if the the
fileextension is not img. The expert/advanced mode accepts any
fileextension. Use img to make it work in any case.
Signed-off-by: Mathias Kresin <dev@kresin.me>
There are already two targets (lantiq, ramips) which use mktplinkfw2
tool for creating images. This de-duplicates code, introduces two new
build commands: tplink-v2-header, tplink-v2-image and makes use of
them in place of old, (sub)target specific ones.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This patch adds support for the Allnet ADSL2+ Modem ALL0333CJ.
Specifications:
- SoC: Amazon-SE
- RAM: 16MB
- Storage: 4MB NOR FLash
- LEDs: Power, Ethernet, DSL (Sync)
- Buttons: 1x Reset Button (not currently supported, will be done)
- 1x Ethernet-Port: 1x RJ45 10/100BaseTX
- 1x WAN-Port: AnnexB & J, G.992.1(ADSL), G.992.3(ADSL2), G.992.5(ADSL2+)
Installation:
- can be done via telnet+tftp or serial console
- default passwords:
- via telnet (root:admin)
- via webinterface http://172.16.1.254:8235/ (admin:coolwhite)
Installation via telnet / tftp:
host: # your own host must have an tftpd daemon, then do this:
host: ifconfig eth0:172 172.16.1.1 up
host: # telnet to allnet modem, root:admin
host: telnet 172.16.1.254
modem: # kill this daemon, it spams your console
modem: killall dsl_cpe_control
modem: # change to some place in ram:
modem: cd /ramdisk/tftp_upload
modem: # load lede-lantiq-ase-ALL0333CJ-squashfs-sysupgrade.bin alias uImage
modem: tftp -g -r uImage 172.16.1.1
modem: # load these extra tools from your tftpd via:
modem: # source: https://github.com/mcmilk/uboot-utils/releases/download/0.1/mips32.tar.gz
modem: tftp -g -r flashwrite 172.16.1.1
modem: tftp -g -r fw_setenv 172.16.1.1
modem: tftp -g -r fw.conf 172.16.1.1
modem: ln -s fw_setenv fw_printenv
modem: chmod +x *
modem: ./fw_setenv disable_recovery y
modem: ./fw_setenv kernel_addr 0xb0010000
modem: ./flashwrite /dev/mtd/1 uImage 0
Installation via serial line at uboot:
uboot: # erase everything exept bootloader
uboot: protect on b0000000 +10000; protect on b03f0000 +10000
uboot: erase all
uboot: # get new firmware via tftp:
uboot: tftpboot 0x80100000 uImage; setenv kernel_addr 0xb0010000
uboot: # copy to flash:
uboot: cp.b 0x80100000 $(kernel_addr) $(filesize)
uboot: # disable proprietary image checking:
uboot: setenv disable_recovery=y; saveenv
uboot: # reboot with LEDE ;)
uboot: reset
Ethernet works as expected, DSL syncronization does not work properly
currently, I am working on this issue.
Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
Enable the building of Netgear DGN1000B images. I have an
example device here, but it was not tested currently.
Also WLAN and USB is not ready in the moment.
This is just the proper way, so that developing on this
device is known to be done in the near future.
Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
The ASL56026 is a VDSL2 router with dual 100mbit ethernet,
also known as the ECI B-FOCuS V-2FUb/I.
CPU: Lantiq XRX268 v1.1 at 333MHz
Modem: Lantiq VRX208
RAM: 32MiB DDR2 at 167MHz
Flash: 8MiB NOR, Spansion S29GL064N90TF04
UART is at JP1:
Pin 1 TX
Pin 2 GND
Pin 3 +3.3V
Pin 4 NC
Pin 5 RX
Boot selection pins are exposed via several resistor jumpers:
boot_sel0 is at J15, on the rear of the board. Default is high.
boot_sel1 is at J3, next to the flash - it is also the flash CE# pin. Default is low.
boot_sel2 is at J12, directly below the SoC. Default is low.
boot_sel3 is at J16, on the rear of the board. Default is low.
The boot_sel pins should never be shorted, the jumper must be moved or
a lower value resistor used to change the pull (existing resistors are 4k7, 1k should work)
To install with the stock bootloader you must break the built in image selection process
which uses at least the following vars: f_upgrade_addr, f_upgrade2_addr, loadaddr, kernel_addr, activeregion, committedregion
This is done by setting loadaddr and both f_upgrade_addr vars to the same address:
VR9 # setenv loadaddr 0xB0040000
VR9 # setenv f_upgrade_addr 0xB0040000
VR9 # setenv f_upgrade2_addr 0xB0040000
VR9 # saveenv
Then flash the firmware image:
VR9 # tftpboot 0x81000000 lede-lantiq-xrx200-ASL56026-squashfs-sysupgrade.bin
VR9 # erase B0040000 +${filesize}
VR9 # cp.b 0x81000000 0xB0040000 ${filesize}
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
The VGV7510KW22BRN and VGV7519BRN do not have the same brnImage
signature. It was accidentally changed with ba42c1d ("lantiq: un-macro
the image building code").
Signed-off-by: Mathias Kresin <dev@kresin.me>
The following commit changed the build templates name but forgot to
update the TARGET_DEVICES variable properly.
commit f9226158be (lantiq: rename EASY98000 to EASY98000NOR)
Signed-off-by: John Crispin <john@phrozen.org>
This moves the extraction of the eeprom/calibration data to a hotplug
firmware script. Additionally it modifies all .dts to configure ath9k
directly from within the .dts.
The owl-loader approach enables support on devices with exotic eeprom
data locations (such as unaligned positions on the flash or data
inside an UBI volume).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[add ath9k caldata mac address patcher]
[fixes DGN3500 wifi mac]
[fixes BTHOMEHUBV3A wifi mac]
[set invalid mac for BTHOMEHUB2B, FRITZ3370, FRITZ7320 & FRITZ7360SL to restore previous random mac behavior]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This adds support for the Intel Falcon SoC for GPON.
Support for the Falcon SoC was removed in commit c821836395 svn rev:
40392 from OpenWrt, this commit adds it again.
This patch adds a new subtarget for the Falcon SoC, but it still misses
all the drivers needed to control the GPON part.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The DEVICE_PACKAGES are not included in the initramfs image in case
TARGET_PER_DEVICE_ROOTFS is set. This might produces initramfs images
with a not working network configuration because of a missing swconfig.
Workaround the issues by adding the essential swconfig package to the
default packages selection and deselect swconfig for boards not having
swconfig included before via device packages.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the new image build code and remove the lzma loader. The lzma
loader was used to cheat the signature validation of the bootloader and
I found another way to do this.
To migrate boards already using LEDE/OpenWrt to the new image the
following steps need to be done once:
VR9 # run reset_uboot_config
VR9 # reset
VR9 # setenv ethaddr AA:BB:CC:DD:EE:FF
VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
VR9 # saveenv
VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
VR9 # erase 0xb0020000 $(filesize)
VR9 # cp.b 0x81000000 0xb0020000 $(filesize)
The mac address is printed on the label at the bottom of the case.
The following steps are need to be done during first install:
VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
VR9 # saveenv
VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
VR9 # erase 0xb0020000 $(filesize)
VR9 # cp.b 0x81000000 0xb0020000 $(filesize)
The image uses the uImage firmware splitter now instead of hardcoded
kernel and rootfs partitions. The firmware partition size was extended
to use flash space that was reserved for partitions required only by
the ECI firmware.
Due to the changes an upgrade to a later LEDE revision from a running
LEDE is supported now.
A default switch config was added and the device uses the same MAC
addresses as the ECI firmware now instead of the same for all VG3503J.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The WBMR boards are the only ones in the whole tree selecting the wpad
and hostapd-utils package by default.
Remove the wps uci-default script as well, there is no obvious reason
why the wps config need to be set only for this board.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Due to the introduced double whitespace the default package selection
isn't applied. This leads to errors like a not working networking
because of a missing swconfig binary.
Fixes FS#208.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add USB led aliases to boards having an led which is meant to be used
as USB led according to the manuals.
Remove the kmod-ledtrig-usbdev from the default package selection for
boards not having an USB led. Add the kmod-ledtrig-usbdev to boards
where it is missing.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Device/AVM unconditionally inherits Device/NAND, which changes the
sysupgrade image to sysupgrade-tar (instead of a "raw" sysupgrade image
as used in the Device/Default template).
This moves the Device/NAND call to the FRITZ3370 device definition, as
this is the only AVM/EVA device that uses NAND.
Additionally we have to define the IMAGE_SIZE for the AVM/EVA NOR
devices to ensure that the images are not discarded.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
By default USB LEDs are associated with usbdev trigger. However,
not all devices which have USB LEDs have kmod-ledtrig-usbdev in their
list of default packages. Add it to the relevant devices.
Signed-off-by: Matti Laakso <matti.laakso@outlook.com>
Now that the "sysupgrade-nand" step is used by non-NAND targets as well,
rename it to "sysupgrade-tar" to make it more generic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Both devices were converted to the new image build code but still using
the LegacyDevice define. Therefore an image isn't created for the
mentioned devices.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Mathias Kresin
Felix Fietkau
Luis Araneda
Zoltan HERPAI
Thibaut VARÈNE
Daniel Golle
Thomas Nixon
Piotr Dymacz
Tino Reichardt
Alex Maclean
John Crispin
Hauke Mehrtens
Martin Blumenstingl
Ben Mulvihill
dpeddi
Eddi De Pieri
Rafał Miłecki
Matti Laakso
Jo-Philipp Wich