The libblkid probe support in fstools git head requires blkid/blkid.h for
compilation, so add a build dependency on util-linux which provides libblkid.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The QorIQ LS1012A processor, optimized for battery-backed or
USB-powered, integrates a single ARM Cortex-A53 core with a hardware
packet forwarding engine and high-speed interfaces to deliver
line-rate networking performance.
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
LEDE/OPENWRT will auto strip executable program file while make. So we
need select CONFIG_NO_STRIP=y while make menuconfig to avoid the ppfe network
fiemware be destroyed, then run make to build ls1012ardb firmware.
The fsl-quadspi flash with jffs2 fs is unstable and arise some failed message.
This issue have noticed the IP owner for investigate, hope he can solve it
earlier. So the ls1012ardb now also provide a xx-firmware.ext4.bin as default
firmware, and the uboot bootcmd will run wrtboot_ext4rfs for "rootfstype=ext4"
bootargs.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
Add support for NXP layerscape ls1043ardb 64b/32b Dev board.
LS1043a is an SoC with 4x64-bit up to 1.6 GHz ARMv8 A53 cores.
ls1043ardb support features as: 2GB DDR4, 128MB NOR/512MB NAND, USB3.0, eSDHC,
I2C, GPIO, PCIe/Mini-PCIe, 6x1G/1x10G network port, etc.
64b/32b ls1043ardb target is using 4.4 kernel, and rcw/u-boot/fman images from
NXP QorIQ SDK release.
All of 4.4 kernel patches porting from SDK release or upstream.
QorIQ SDK ISOs can be downloaded from this location:
http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
- setting read-only flag to important partitions
- enabling PA to improve 2.4 GHz signal strength
- add missing leds
- rename colour led
- add mac adress to 5GHz wlan interface
- included <dt-bindings/input/input.h> and <dt-bindings/gpio/gpio.h>
Signed-off-by: Henryk Heisig hyniu@o2.pl
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit 064f467264c5c9b6eca0bb96b587f9412b770cc5)
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit eb0ce57270d0b5b81b224b9336cf54707497eede)
Modified after cherry-pick:
obj in Makefile
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Created minimal patchset based on BB rev 43158 by Eddi De Pieri
14.07/openwrt.git 79472c025449efae9310defad0d3a73cff14d756
If the VR9 based router provides FXS ports and they shoud enabled then
the following must added to the kernel command line:
mem=[TOTALMEMSIZE-2M] vpe1_load_addr=ADDRESS vpe1_mem=2M maxvpes=1
maxtcs=1
To use FXS 2M of RAM are needed for the VPE firmware. The size is set
by vpe1_mem.
The available RAM must be reduced by this size using the mem argument.
A correct load address (example 0x83e00000) for the firmware must be given,
too.
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit 8d924d43c0ea6839a3a33e54982e8da48b736001)
Modified after cherry-pick:
compatible attribute
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit 47b1ff965b0cb57013b40fbe2bcd7f3c6eb6b606)
Modified after cherry-pick:
FW_MD5SUM in Makefile
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit ea9e61b8eb61a2e362a50541f03466dc7d087947)
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on ar71xx, brcm47xx, kirkwood.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
We need to tell hwclock with -u commandline option, that we would like
to keep our RTC clock in UTC timezone. Linux kernel expects RTC in UTC
timezone anyway.
In current state of things, we don't tell hwclock to load/store time
from/to RTC in UTC timezone so it uses the timezone from the system
time. If it's set to different timezone then UTC, sysfixtime is going to
screw the time in RTC.
I've following in the setup script:
uci set system.@system[0].timezone='CET-1CEST,M3.5.0,M10.5.0/3'
uci set system.@system[0].zonename='Europe/Prague'
I've this RTC setup (rtc1 is RTC on i.MX6 SoC, rtc0 is battery backed RTC mcp7941x):
rtc-ds1307 3-006f: rtc core: registered mcp7941x as rtc0
snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1
Then we can experience following (current time is 10:15am):
$ date
Fri Oct 21 10:15:07 CEST 2016
$ hwclock -r -f /dev/rtc0
Fri Oct 21 08:14:46 2016 0.000000 seconds
$ hwclock -u -r -f /dev/rtc0
Fri Oct 21 10:14:46 2016 0.000000 seconds
And after current broken sysfixtime:
$ /etc/init.d/sysfixtime stop
$ date
Fri Oct 21 10:15:25 CEST 2016
$ hwclock -r -f /dev/rtc0
Fri Oct 21 10:15:31 2016 0.000000 seconds
Now we've time in our battery backed RTC in CEST timezone instead of
UTC. Then once again, but with this patch applied to sysfixtime, where
hwclock is using correctly the -u parameter:
$ /etc/init.d/sysfixtime stop
$ date
Fri Oct 21 10:15:53 CEST 2016
$ hwclock -r -f /dev/rtc0
Fri Oct 21 08:15:55 2016 0.000000 seconds
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Ensure that selecting the wpa-supplicant-mesh package actually packages the
wpa_supplicant binary with SAE support and add missing dependency on OpenSSL.
Signed-off-by: Alexis Green <alexis@cessp.it>
[Jo-Philipp Wich: slightly reword commit message for clarity]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
We add an 'httpauth' section type that contains the options:
prefix: What virtual or real URL is being protected
username: The username for the Basic Auth dialogue
password: Hashed (crypt()) or plaintext password for the Basic Auth dialogue
httpauth section names are given included as list
items to the instances to which they are to be applied.
Further any existing httpd.conf file (really whatever
is configured in the instance, but default of
/etc/httpd.conf) is appended to the per-instance httpd.conf
Signed-off-by: Daniel Dickinson <lede@cshore.thecshore.com>
fix parsing of the < > quoted time zone names. Compare the correct
character instead of repeatedly comparing the first character.
Patch has been submitted to upstream as
http://www.openwall.com/lists/musl/2016/10/24/3
Longer explanation in
http://www.openwall.com/lists/musl/2016/10/19/1
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[Jo-Philipp Wich: move references into commit message, shorten title prefix]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Both the MR12 and MR16 are single gigabit ethernet devices, similar to the
MR18. This change gives them the correct network config on a fresh install.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
[Jo-Philipp Wich: adjust for alphabetical ordering, line wrap commit msg]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
In 814d70b2 the member mac06_exchange_en of struct
ar8327_pad_cfg was changed to mac06_exchange_dis,
but wpj344 was not adopted to stay in sync.
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Reported-by: Nick Dennis <ndennis@rapiduswireless.com>
During reload, we could send invalid information to the other
side and confuse it.
That's why, during reload we'll pause execution, do the reconfig
and resume + update when reload is done.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
The problem is that interfaces are specified at start as
command line arguments, making them unchange-able via reload.
That means, we have to move (since lldpd allows this) the
interfaces-match-pattern option to be in a config file and reload
the configuration.
It's either that, or do a 'restart'.
Since we're generating the lldpd.conf file, we'll have to
move the 'sysconfdir' of lldpd to /tmp, where the files will
get written ; this will prevent any unncessary flash writes.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Looking into /usr/include/stdlib.h, there's a `devname()` function defined
under some #ifdef's which conflicts with the `static char *devname` definition
in `src/mkwrggimg.c`.
Defining `_ANSI_SOURCE` in the `src/mkwrggimg.c` file, omits that part of the
header.
Another more intrusive approach is to rename `devname` to something like
`g_devname` in `src/mkwrggimg.c`. But I think the `_ANSI_SOURCE` define should
be enough.
Compilation error is:
src/mkwrggimg.c:64:14: error: redefinition of 'devname' as different kind of symbol
static char *devname;
^
/usr/include/stdlib.h:286:7: note: previous definition is here
char *devname(dev_t, mode_t);
^
src/mkwrggimg.c:147:12: error: non-object type 'char *(dev_t, mode_t)' (aka 'char *(int, unsigned short)') is not assignable
devname = optarg;
~~~~~~~ ^
src/mkwrggimg.c:192:6: warning: comparison of function 'devname' equal to a null pointer is always false [-Wtautological-pointer-compare]
if (devname == NULL) {
^~~~~~~ ~~~~
src/mkwrggimg.c:192:6: note: prefix with the address-of operator to silence this warning
if (devname == NULL) {
^
&
src/mkwrggimg.c:251:27: warning: incompatible pointer types passing 'char *(dev_t, mode_t)' (aka 'char *(int, unsigned short)') to parameter of type 'const char *' [-Wincompatible-pointer-types]
strncpy(header->devname, devname, sizeof(header->devname));
^~~~~~~
/usr/include/secure/_string.h:119:34: note: expanded from macro 'strncpy'
__builtin___strncpy_chk (dest, src, len, __darwin_obsz (dest))
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
[Jo-Philipp Wich: slightly reformat commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Thanks to leaving .pattern file we can easily insert extra step between
linksys-pattern-partition and trx-v2-with-loader, e.g. rootfs one.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The old usbdev trigger never supported assigning more than 1 USB port.
This code we got was never working as expected and it was missing 2 more
ports. Switch to usbport to have LED working with all ports.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tested-by: Christian Lamparter <chunkeey@gmail.com>
The current default rootfs size of 256MB in conjunction with 4K blocks
produces an ext4 filesystem which lacks the appropriate amount of backup GDT
entries to support online-resizing.
For x86 targets, increase the default rootfs size to 2048MB which allows
online resizing the filesystem to up to 2TB which is the current theoretical
maximum for LEDE, due to missing GPT support on the root block device.
Note that the filesystem artefact will not occupy 2GB on the build system as
the make_ext4fs utility uses sparse files to generate the filesystem images,
so the actual disk usage is much lower. Furthermore the filesystem images
are gzip compressed, shrinking them to only a few megabytes on the download
server.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Acked-by: Michael Heimpold <mhei@heimpold.de>
There is very little practical use to limit the number of available inodes on
an ext4 filesystem and the make_ext4fs utility is able to calculate useful
defaults by itself.
Drop the option to make resulting ext4 filesystems more flexible by default.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Acked-by: Michael Heimpold <mhei@heimpold.de>
Allow CONFIG_TARGET_EXT4_RESERVED_PCT to be empty as make_ext4fs is usually
able to figure out a suitable default.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Reviewed-by: Michael Heimpold <mhei@heimpold.de>
Capitalized "disc" submenu name as all submenu names are capitalized (apart from "database", but I'll fix that
later).
moved "swap-utils" to Filesystem submenu as it is "formatting" a partition as swap so it looks out of place in Disc.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Currently the reset script will try to run jffs2reset on boards that are
running a rw rootfs, such as ext4. This will cause jffs2reset to fail
and the board to never reboot while the LED blinks until a manual
reboot.
This commit does two different things:
1. Disables reset on boards that do not have an overlay mount
2. Disables the Blinking LED after 5 seconds if the board does not
support reset
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Fix the default value for the 'bootcmd' environment variable.
Therefore make the default bootcmd work for buildbot's images.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Fixes the same hctosys init issue as described in commit
5481ce9a11
The Gateworks Ventana family uses an emulated Dallas 1672
RTC device.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Jo-Philipp Wich
Henryk Heisig
Yutang Jiang
Stefan Koch
Pavel Kubelun
Rosen Penev
John Crispin
Paul Wassi
Petr Štetiar
Hauke Mehrtens
Alexis Green
Petr Konecny
Daniel Dickinson
Hannu Nyman
Chris Blake
Christian Mehlis
Alexandru Ardelean
Rafał Miłecki
Daniel Engberg
Alberto Bursi
Ben Greear
Chris Blake
Koen Vandeputte