Support for the BT HomeHub 2.0 Type A.
This router was manufactured by Thomson, and it's BCM6358 based.
The leds are controled by two chained HC594, all working ok. The BCM5325
switch has the RESET# pin wired to the GPIO15, but currently there is no
way to tell the b53 driver how to get this gpio number in brcm63xx,
therefore swconfig won't use it when performing a switch reset.
The patch was tested with several firmwares, and all except unsupported
stuff (i.e xDSL) works pretty well.
Tested-by: Tahir <tahir00ali@gmail.com>
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
SVN-Revision: 44985
Currently there isn't images ready for flashing liveboxes boards. This
patch adds a script and the code to call it in the bcm63xx images
builder makefile to generate the livebox 1 firmware.
I removed some lines to avoid generating unneded files in the bin/ dir
for this board. And added code to generate a squashed rootfs aligned to
64 kB since the current one in the /bin dir is 128 kB aligned and
doesn't work. Still no sysupgrade support for this board. Upgrading from
within openwrt can be done writing with mtd the kernel, and then the 64k
aligned rootfs.
Regards
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: use sed instead of a separate shell script for the boot script, make it
respect the load address]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44982
This adds support for the Netgear DGND3700 v1 and DGND3800B.
DGND3700 v1 and DGND3800B are exactly the same router, only one difference,
the factory firmware. This patch produces two factory firmwares for each router.
The router includes an onboard NAND flash for extra storage. NAND is currently
not supported in bcm63xx, so no code added for this part. The NOR flash (32MB)
is enough for storing an openwrt firmware.
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: Add back commit message from v1]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44831
Add a dtsi for bcm3368, add a dts and profile for cvg834g, and convert
it to use ImageDTB. Since HCS requires more arguments, enhance the max
arguments of the call.
The image name is intentionally left blank to prevent non-initramfs
images to be built, as they currently contain no rootfs and consequently
won't work.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44561
Most 16 MiB RAM devices don't even load elf kernels, so it's safe to
assume we have at least 32 MB RAM. This fixes tftp booting with the
default package set as this already produces an uncompressed
kernel > 8 MiB.
New limit is 8 MiB compressed / 24 MiB compressed.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44558
We do not need to align the start of read only rootfs's to erase blocks.
This allows us to write the squashfs rootfs directly behind the kernel,
potentially freeing up one erase block.
We still need to align for jffs2, so add a flag for imagetag to
optionally align the rootfs start.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44556
According to the vendor tarball, the TD-w8900GB's flash has 64k erase
block size, but CFE spans two blocks. So fixup the image offset
accordingly but keep block size at its default (64k).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: add commit message, add image offset, change nvram offset]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43572
If there is no board support in the kernel, it does not make sense to
build images for devices. So drop any images for board ids for which
there are nc corresponding board_info structs in the kernel.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43364
This prevents generating every supported image, except for de "Default" profile.
Also fixes Neufbox 6 image generation.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42210
Now that we migrated all users to dtb based detection, we can drop the
board fixup code.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42129
This requires individual images for each board version for now.
Linux partition was shrunk to ensure writing thewrong image won't
erase wifi calibration data.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42126
In preparation for switching to dtb based board identification, add
support for building lzma-loader and lzma cfe kernels with dtb
appended.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42121
Add a working lzma loader and use it for generating initramfs kernels
to allow easily netbooting elf kernels on devices with a 4 MiB CFE
size limit.
Based on ar71xx's lzma-loader.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41940
This patch also makes use of the new leds script.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41585
This adds support for Comtrend WAP-5813n.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: refresh patches]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41421
Support for Asmax AR 1004g router
Signed-off-by: Adrian Feliks <mexit@o2.pl>
Patchwork: http://patchwork.openwrt.org/patch/4464/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39674
This adds profile and build image for Sagemcom F@st2704, using b43
driver.
For WiFi to work properly BCMA fallback SPROM support patch must
be applied (http://git.io/z1Ki8A).
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4212/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39673
In order to support both normal images and initramfs, ensure that each
target sets KERNELNAME properly so that the generic kernel building code
can copy the corresponding files over $(KDIR) with the appropriate
extension. Update the various paths to the kernel and wrapper images
from $(LINUX_DIR)/arch/$(ARCH)/boot/$(foo) to $(KDIR)/$(foo).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 37049
Cable Modem devices cannot load an ELF file directly so we need to
provide them with a HCS image even when targetting initramfs.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 36954
$(KDIR)/vmlinux is already a binary image, there is no need to create
another one.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 36949
Jonas Gorski
Florian Fainelli