The helper shared Build/append-uboot in include/image-commands.mk
uses it, so include this variable in DEFAULT_DEVICE_VARS.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Adds a new variable DISABLED_SERVICES to ImageBuilder Makefile, which
defines a list of services (installed as /etc/init.d/*) to be disabled
during the build of a custom image (normally all are enabled).
It comes handy when a particular service should not be run under normal
circumstances, but should be ready in the image for situations when it
might be needed.
Signed-off-by: Richard Musil <risa2000x@gmail.com>
If the target supports a newer kernel version that is not used by default
yet, it can be enabled with this option
Signed-off-by: Felix Fietkau <nbd@nbd.name>
No target is using kernel 3.18 anymore, remove all the generic
support for kernel 3.18.
The removed packages are depending on kernel 3.18 only and are not used on
any recent kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Refreshed all patches.
New symbols:
- CONFIG_LDISC_AUTOLOAD
- CONFIG_PPC_BARRIER_NOSPEC
Compile-tested on: ar7
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This patch doesn't seem to have any more users.
The only one used to be target in
`target/linux/etrax/image/e100boot/Makefile`.
That target has since been removed via commit
1080f68b2b .
There doesn't seem to be any reason left for this workaround.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Otherwise tar will keep the sgid bit when running
from a sgid-set directory, resulting in a different
file being generated.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[reworked commit message, removed DMARC]
It was reported to me on IRC today, that my change causes issues with
kernel versions between 4.14 and 4.19.
It's because I've wrongly used `git describe` in order to get kernel
version where we should disable noisy DTC checks, but I should've used
`git tag --contains` instead.
Fixes: cbbef976e2 ("build: dtc: Disable noisy warnings by default")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Set the toolchain's ARM CPU and FPU architectures by utilizing' gcc's
--with-cpu / --with-fpu configure options that: "Specify which cpu
variant the compiler should generate code for by default. cpu will
be used as the default value of the -mcpu= switch."
This will resolve the following kernel compilation failures under
gcc 8.x on ARM because the kernel wants to set (possibly conflicting)
optimization flags.
.../ccyVnmrs.s:204: Error: selected processor does not support `dmb ish' in ARM mode
.../ccyVnmrs.s:215: Error: architectural extension `mp' is not allowed for the current base architecture
.../ccyVnmrs.s:216: Error: selected processor does not support `pldw [r4]' in ARM mode
Because this is a big change, the .config and toolchain need to be
refreshed (as in removed and regenerated).
Reported-by: Ansuel Smith <ansuelsmth@gmail.com>
Reported-by: Daniel Engberg <daniel.engberg.lists@pyret.net> [#1203]
Signed-off-by: Boris Krasnovskiy <borkra@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [extended commit message,
removed now-deprecated CPU_CFLAGS, changed author to gmail address]
If no feed.conf or feeds.conf.default is found on image generation with
the imagebuilder we always get the following message "Unable to open
feeds configuration at <dir>/scripts/feeds line 48." on std error.
To get rid off this needless warning on image generation with the
imagebuilder supress the output in feeds.mk.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Having image metadata (and signature) appended is a condition for
semi-automated sysupgrade, hence IB needs to be able to tell which
images will end up with metadata.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
allow downstream projects to see the current version of the metadata,
usefull if eventually more variables change
Signed-off-by: Paul Spooren <mail@aparcar.org>
currently the "board" parameter contains $(BOARD) which actually results
to `<target>` (like ramips, ar71xx) without subtarget. However, one
actually excepts (not?) to contain BOARD_NAME or DEVICE_NAME.
Signed-off-by: Paul Spooren <mail@aparcar.org>
When autoloading more than one modules per packages,
/etc/modules.d/$module depends on the file system ordering.
To test this: use disorderfs on the build_dir and build kmod-sched.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
squashfskit is a fork of the squashfs-tools.
squashfskit creates reproducible filesystems and includes
many of the distro patches.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: Paul Spooren <mail@aparcar.org>
Use 'dtc' from kernel sources instead of relying on host tool.
Fixes: bf4630e5ad ("build: add helpers for generating QSDK sysupgrade compatible images")
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Qualcomm SDK (QSDK) sysupgrade compatible images for IPQ40xx, IPQ806x
and IPQ807x use FIT format together with 'dumpimage' tool from U-Boot
for verifying and extracting them. Based on 'images' sections names,
corresponding mtd partitions are flashed. For example, in case of
NOR-only boards, below mapping is used (section name -> mtd name):
hlos* -> 0:HLOS
rootfs* -> rootfs
And for boards with NAND (kernel inside UBI):
ubi* -> rootfs
Above mappings come from unmodified QSDK sources and might be wrong for
boards running custom or modified QSDK-based firmware. Some of vendors
adjust them to meet their modified mtd layout or features like recovery
or dual-image support.
This adds simple script 'mkits-qsdk-ipq-image.sh' (based on 'mkits.sh')
for generating FIT images tree source files, compatible with the QSDK
sysupgrade format. Resulting images can be used for initial (factory ->
OpenWrt) installation and would work both in CLI and GUI.
The script is universal in a way it allows to include as many sections
as needed. To make use of it, two generic/basic build recipes for NOR
and NAND based boards are also included in 'image-commands.mk':
Build/qsdk-ipq-factory-nand
Build/qsdk-ipq-factory-nor
Example usage for board with UBI in NAND:
IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The original patch removed the printing completely, just remove the
color.
Fixes: eabc1ddc45 ("build: Honour NO_COLOR in include/scan.mk")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
BIN_DIR can be set to overwrite the output path for new images. This is an
advertised feature for the imagebuilder and is used by systems like
LibreMesh's chef.
The legacy images are build using a new sub-make which doesn't receive the
variable overwrites of the parent make process. As result, the BIN_DIR is
automatically defined to the default value from rules.mk. The images will
therefore not be placed in the output path which was selected by the user.
Providing BIN_DIR as an explicit variable override to the sub-make works
around this problem.
Fixes: 26c771452c ("image.mk: add LegacyDevice wrapper to allow legacy image building code to be used for device profiles")
Reported-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Hi all:
This is my first OpenWrt patch. I am a clean, pure newbie! 8-)
Honour NO_COLOR in Makefile function 'progress' in include/scan.mk, in the same way that include/verbose.mk does.
Signed-off-by: R. Diez <rdiezmail-openwrt@yahoo.com>
The KERNEL_ENTRY was missing from the DEFAULT_DEVICE_VARS.
This bug was discovered while preparing alternative images
for the mpc85xx's TP-Link WDR4900-V1, which all failed to
boot due to this:
|## Booting kernel from Legacy Image at 02000000 ...
| Image Name: POWERPC OpenWrt Linux-4.14.96
| Image Type: PowerPC Linux Kernel Image (uncompressed)
| Data Size: 2056568 Bytes = 2 MiB
| Load Address: 01000000
| Entry Point: 00000000
| Verifying Checksum ... OK
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
It was reported to me today on IRC, that building of artifacts doesn't
work properly if the concat_cmd references DEVICE_NAME variable. I've
found out, that it's due to missing call of Device/Export in artifacts
building code path, so this patch adds the missing Device/Export call
which in turn exports DEFAULT_DEVICE_VARS into the artifacts
environment.
Fixes: 493c9a3551 ("build: Introduce building of artifacts")
Tested-by: Oskari Lemmela <oskari@lemmela.net>
Reported-by: Oskari Lemmela <oskari@lemmela.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Use LINUX_DIR as a path when patching kernel. Doesn't break the current usage,
but allows to create packages that will contain variation of a kernel with
kernel being build in some subdirectory of PKG_BUILD_DIR.
Signed-off-by: Michal Hrusecky <michal.hrusecky@nic.cz>
This fixes two issues with cleaning package files from STAGING_DIR:
* CleanStaging currently can only remove files and not directories. This
changes CleanStaging to use clean-package.sh, which does remove
directories.
* Because of the way directories are ordered in the staging files list,
clean-package.sh currently tries (and fails) to remove parent
directories before removing subdirectories. This changes
clean-package.sh to process the staging files list in reverse, so that
subdirectories are removed first.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
While helping with review and build testing of a few 4.19 pull requests,
I've noticed, that dtc compiler in OpenWrt uses different options then
upstream kernel, which is leading to a very noisy output[1]. It wouldn't
be that bad per se, but a lot of such warnings aren't easily fixable so
I think, that we should follow what upstream does and simply ignore^W
silence those noisy warnings.
So this patch tries to syncs dtc compiler flags with upstream kernel
till version 4.19.13, disabling those warnings as they were added in
upstream kernel:
v4.6-rc1-2-gbc55398 dtc: turn off dtc unit address warnings by default
The newly added dtc warning to check DT unit-address without reg
property and vice-versa generates lots of warnings. Turn off the check
unless building with W=1 or W=2.
v4.11-rc2-11-g8654cb8 dtc: update warning settings for new bus and node/property
dtc gained new warnings checking PCI and simple buses, unit address
formatting, and stricter node and property name checking. Disable the
new dtc warnings by default as there are 1000s. As before, warnings are
enabled with W=1 or W=2. The strict node and property name checks are a
bit subjective, so they are only enabled for W=2.
v4.16-rc3-9-g4fd98e3 scripts: turn off some new dtc warnings by default
The latest dtc update adds some new noisy warnings, so turn them off by
default. Disable 'avoid_unnecessary_addr_size' and 'alias_paths'. They
can be re-enabled by building with 'W=1'.
v4.17-rc1-27-g74656b6 kbuild: disable new dtc graph and unit-address warnings
dtc gained some new warnings for OF graphs and unique unit addresses,
but they are currently much too noisy. So turn off
'graph_child_address', 'graph_port', and 'unique_unit_address' warnings
by default. They can be enabled by building dtbs with W=1.
Build tested on imx6 and ath79 with 4.14 and 4.19.
1. https://github.com/openwrt/openwrt/pull/1694#issuecomment-450864335
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch fixes following error with U-Boot 2019.01 on imx6:
In file included from tools/lib/crc16.c:1:0:
./tools/../lib/crc16.c: In function 'crc16_ccitt':
./tools/../lib/crc16.c:70:2: error: 'for' loop initial declarations are only allowed in C99 mode
for (int i = 0; i < len; i++)
^
./tools/../lib/crc16.c:70:2: note: use option -std=c99 or -std=gnu99 to compile your code
Code was introduced in the upstream v2019.01-rc1-154-g51c2345:
commit 51c2345bd24837f9f67f16268da6dc71573f1325
Author: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Date: Sun Nov 25 19:22:19 2018 +0100
Roll CRC16-CCITT into the hash infrastructure
Upstream has added -std=gnu11 host flag in v2018.07-rc2-1-gfa89399:
commit fa893990e9b53425af5f5059e04a2bffde91ccf9
Author: Tom Rini <trini@konsulko.com>
Date: Tue Jun 19 23:53:54 2018 -0400
Makefile: Ensure we build with -std=gnu11
Build tested on imx6: apalis, mx6sabresd, nitrogen6dl, nitrogen6dl2g,
nitrogen6q, nitrogen6q2g, nitrogen6s, nitrogen6s1g,
wandboard
Run tested: apalis (pending PR #1595)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit adds the 'Build/linksys-image' rule and the
'linksys-image.sh' script to the build system.
This change is needed for generating factory images for the Linksys
EA6350v3 device. Without this patch, only valid sysupgrade images can be
generated. With this patch, users can flash the device without the
need of physical access or disassembly.
Signed-off-by: Ryan Pannell <ryan@osukl.com>
Signed-off-by: Oever González <notengobattery@gmail.com>
This adds the hardening options also to the toolchain build.
With this change the /usr/lib/libstdc++.so.6.0.24 library will have
stack canaries and the /lib/libgcc_s.so.1 library will have Full RELRO.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
- Filter out potential duplicates with the package name
(e.g. when renaming libfoo1 w/ ABI_VERSION:=1 to libfoo)
- Use the GetABISuffix macro to properly separate the suffix
with a dash in case the basename ends with a number
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
When a library package specifies additional provides, e.g. libncurses
which provides libncursesw, we should also append the abi version
suffix to each provide, since there may be more than one package
providing the virtual library.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This may be useful if you don't entirely trust your flash and want to be able
to check for corruptions.
Signed-off-by: Michal Hrusecky <Michal@Hrusecky.net>
Add the ABI_VERSION source makefile variable to the binary package basename
and resolve source dependencies on packages with ABI_VERSION set to such
expanded names.
If for example a package specifies DEPENDS:=libopenssl while the OpenSSL
Makefile specifies ABI_VERSION:=1.0.0, the resulting ipk control data
dependency will be "Depends: libopenssl1.0.0" and the libopenssl ipk file
will be called "libopenssl1.0.0_<version>_<arch>.ipk".
The next time a library such as OpenSSL is updated to an incompatible
version, the ABI_VERSION shall be changed accordingly to prevent opkg from
simply upgrading to an incompatible library without considering the
dependencies of already installed packages.
Also introduce another "SourceName" control field which is required by
the newly introduced "scritps/ipkg-remove" to determine the proper related
.ipk files to delete upon buildroot package clean operations.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Subdequent commits need this information to resolve the ABI version when
computing binary ipk dependencies.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Subsequent commits will put more auxiliary information into this file,
such as the per-package ABI version, so rename the metadata script
subcommand and file names accordingly.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Move the zip compression into a build recipe. Pad the image using the
existing build recipes as well to remove duplicate functionality
Change the code to append header and footer in two steps. Allow to use a
fixed filename as the netgear update image does.
Use a fixed timestamp within the zip archive to make the images
reproducible.
Due to the changes we are now compatible to the gnu89 c standard used by
default on the buildbots and we don't need to force a more recent
standard anymore.
Beside all changes, the footer still looks wrong in compare to the
netgear update image.
Signed-off-by: Mathias Kresin <dev@kresin.me>
I moved xor-image into image-commands.mk to use it in ath79 target.
It required for NEC WG800HP.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Refresh all patches
Remove upstream patch:
backport-4.14/424-v4.20-net-dsa-fix-88e6060-roaming.patch
Minor tweak to generic/hack-4.14/902-debloat_proc.patch to cleanly apply
after upstream changes.
Tested-on: ath79
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
We need to use resolved file list as prerequisites for repacking kmod
.ipk files. Note that currently version_filter uses a Makefile macro
KERNEL_PATCHVER that should be available at ipk building time.
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This commit ports both dir-825-c1 and dir-835-a1 from ar71xx to ath79.
They're pretty much identical, except dir-835-a1 has less LEDs.
The routers come with 128 MByte of RAM and 16 MBytes of flash and sport
2.4GHz and 5.0GHz wireless. Both routers have entries already in
OpenWrt's TOH. Please check there for more information on these
antiquities.
https://openwrt.org/toh/hwdata/d-link/d-link_dir-825_c1https://openwrt.org/toh/hwdata/d-link/d-link_dir-835_a1
Installation:
1. Connect to the web interface of the vendor firmware (usually
listening on 192.168.0.1).
2. Go to "Tools", then "Firmware".
3. In the "Firmware Upgrade" box click "Browse".
4. Select the OpenWrt factory image for your router.
5. Click "Upload", confirm the popups if you agree to flash the file you
selected.
6. Wait for firmware upgrade to complete. It takes about 5 minutes.
Run-tested on dir-825-c1. dir-835-a1 should work as well, but I don't
have this router so I can't confirm.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial changes]
This command enables factory image generation for Cameo boards. On
upgrade the vendor firmware will check the size of the provided image
and if a specific string is located at the end of the binary.
cameo-factory will generate an image that the vendor firmware accepts.
Tested on a D-Link DIR-825 C1 with vendor firmwares 3.01 and 3.04.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
In mainline kernel commit 02c7b25e5f5 ("netfilter: nf_tables: build-in
filter chain type") all chain filters were merged into one file and into
one kernel module to save some memory. The code protected by these
configuration options CONFIG_NF_TABLES_BRIDGE, CONFIG_NF_TABLES_IPV4,
CONFIG_NF_TABLES_ARP, CONFIG_NF_TABLES_IPV6, CONFIG_NF_TABLES_NETDEV and
CONFIG_NF_TABLES_INET was merged into the nft_chain_filter.c file which
is now always compiled into the nf_tables.ko file.
This only happened in kernel 4.19 and OpenWrt has to select these as
modules in older kennel versions. Mark them as build-in in the kernel
4.19 specific kernel configuration file which will then not be
overwritten by the package specific settings which try to make them
modular again.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel commit 0168e8b361 ("netfilter: nat: merge ipv4/ipv6 masquerade
code into main nat module") the CONFIG_NF_NAT_MASQUERADE_IPV4 and
CONFIG_NF_NAT_MASQUERADE_IPV6 kernel configuration option were changed
to bool and the code will not be compiled as a own module any more, but
it will be integrated into nf_nat_ipv4.ko or nf_nat_ipv6.ko to save some
memory.
Activate these options as bool in the generic kernel 4.19 configuration
only, to always build them into the nf_nat_ipv*.ko modules. The kmod
file will still try to select them as module, but the generic
configuration will not be overwritten.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some kernel modules from kmod-ipt-conntrack-extra depend on
nf_conncount.ko, which was added in kernel 4.16, add it to the kmod.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The nf_socket.ko module was split in commit 8db4c5be88f ("netfilter:
move socket lookup infrastructure to nf_socket_ipv{4,6}.c") into a
common, n IPv4 and an IPv6 part.
The nf_tproxy.ko module was split in commit 45ca4e0cf27 ("netfilter:
Libify xt_TPROXY") into a common, an IPv4 and an IPv6 part.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel commit a0ae2562c6c ("netfilter: conntrack: remove l3proto
abstraction") The modules nf_conntrack_ipv4.ko, nf_conntrack_ipv6.ko and
nf_conntrack.ko were squashed together into one module. This module now
depends on nf_defrag_ipv6 when IPv6 support was activated. This is part
of the main netfilter packages, so add nf_defrag_ipv6.ko also to the
default netfilter packages on kernel 4.19 and later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This makes the patches which were just copied in the previous commit
apply on top of kernel 4.19.
The patches in the backports-4.19 folder were checked if they are really
in kernel 4.19 based on the title and only removed if they were found in
the upstream kernel.
The following additional patches form the pending folder went into
upstream Linux 4.19:
pending-4.19/171-usb-dwc2-Fix-inefficient-copy-of-unaligned-buffers.patch
pending-4.19/190-2-5-e1000e-Fix-wrong-comment-related-to-link-detection.patch
pending-4.19/478-mtd-spi-nor-Add-support-for-XM25QH64A-and-XM25QH128A.patch
pending-4.19/479-mtd-spi-nor-add-eon-en25qh32.patch
pending-4.19/950-tty-serial-exar-generalize-rs485-setup.patch
pending-4.19/340-MIPS-mm-remove-mips_dma_mapping_error.patch
Bigger changes were introduced to the m25p80 spi nor driver, as far as I
saw it in the new code, it now has the functionality provided in this
patch:
pending-4.19/450-mtd-m25p80-allow-fallback-from-spi_flash_read-to-reg.patch
Part of this patch went upstream independent of OpenWrt:
hack-4.19/220-gc_sections.patch
This patch was reworked to match the changes done upstream.
The MIPS DMA API changed a lot, this patch was rewritten to match the
new DMA handling:
pending-4.19/341-MIPS-mm-remove-no-op-dma_map_ops-where-possible.patch
I did bigger manual changes to the following patches and I am not 100% sure if they are all correct:
pending-4.19/0931-w1-gpio-fix-problem-with-platfom-data-in-w1-gpio.patch
pending-4.19/411-mtd-partial_eraseblock_write.patch
pending-4.19/600-netfilter_conntrack_flush.patch
pending-4.19/611-netfilter_match_bypass_default_table.patch
pending-4.19/670-ipv6-allow-rejecting-with-source-address-failed-policy.patch
hack-4.19/211-host_tools_portability.patch
hack-4.19/221-module_exports.patch
hack-4.19/321-powerpc_crtsavres_prereq.patch
hack-4.19/902-debloat_proc.patch
This is based on patchset from Marko Ratkaj <marko.ratkaj@sartura.hr>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
They are no longer stored in the "testing" subdirectory and are not
available as .tar.xz archives. If -rc is detected download it from the
git.kernel.org and use .tar.gz.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This commit modifies mtd partitions define for Buffalo BHR-4GRV2 and
move it to generic subtarget.
In Buffalo BHR-4GRV2, "kernel" partition is located behined "rootfs"
partition in the stock firmware. This causes the size of the kernel
to be limited by the fixed value.
0x50000 0xe80000 0xff0000
+-------------------------------+--------------+
| rootfs | kernel |
| (14528k) | (1472k) |
+-------------------------------+--------------+
After ar71xx was updated to Kernel 4.14, the kernel size of BHR-4GRV2
exceeded the limit, and it breaks builds on official buildbot.
Since this issue was also confirmed in ath79, I modified the mtd
partitions to get rid of that limitation.
0x50000 0xff0000
+----------------------------------------------+
| firmware |
| (16000k) |
+----------------------------------------------+
However, this commit breaks compatibility with ar71xx firmware, so I
dropped "SUPPORTED_DEVICES += bhr-4grv2".
This commit requires new flash instruction instead of the old one.
Flash instruction using initramfs image:
1. Connect the computer to the LAN port of BHR-4GRV2
2. Set the IP address of the computer to 192.168.12.10
3. Rename the OpenWrt initramfs image to
"bhr4grv2-uImage-initramfs-gzip.bin" and place it into the TFTP
directory
4. Start the tftp server on the computer
5. While holding down the "ECO" button, connect power cable to
BHR-4GRV2 and turn on it
6. Flashing (orange) diag LED and release the finger from the button,
BHR-4GRV2 downloads the intiramfs image from TFTP server and boot
with it
7. On the initramfs image, create "/etc/fw_env.config" file with
following contents
/dev/mtd1 0x0 0x10000 0x10000
8. Execute following commands to add environment variables for
u-boot
fw_setenv ipaddr 192.168.12.1
fw_setenv serverip 192.168.12.10
fw_setenv ethaddr 00:aa:bb:cc:dd:ee
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
9. Perform sysupgrade with squashfs-sysupgrade image
10. Wait ~150 seconds to complete flashing
And this commit includes small fix; BHR-4GRV2 has QCA9557 as a SoC,
not QCA9558.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Currently every file in boot directory is copied over target /boot on
root file system and is usually inaccessible because appropriate boot
file system is mounted on top of it. Therefore remove /boot, which in
result will also save space on target root file system.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
We currently could (ab)use IMAGES for this task, but the downside is,
that the filenames has filesystem tied to the filename, which might be
confusing as the artifact itself don't has to be used with that specific
filesystem. Another downside is, that the artifacts built with IMAGES
target are build for every FILESYSTEMS filesystem.
Consider following use case:
define Device/apalis
...
FILESYSTEMS := ext4 squashfs
IMAGES := spl-uboot.bin recovery.scr
IMAGE/spl-uboot.bin := append-uboot-spl | pad-to 68k | append-uboot
IMAGE/recovery.scr := recovery-scr
endef
Where we would get target binaries with following filenames:
openwrt-imx6-apalis-squashfs.recovery.scr
openwrt-imx6-apalis-squashfs.spl-uboot.bin
openwrt-imx6-apalis-ext4.recovery.scr
openwrt-imx6-apalis-ext4.spl-uboot.bin
With proposed patch, we could now just do:
define Device/apalis
...
ARTIFACTS := spl-uboot.bin recovery.scr
ARTIFACT/spl-uboot.bin := append-uboot-spl | pad-to 68k | append-uboot
ARTIFACT/recovery.scr := recovery-scr
endef
Which would produce target binaries with following filenames:
openwrt-imx6-apalis-recovery.scr
openwrt-imx6-apalis-spl-uboot.bin
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
The -rcX "testing" kernels are no longer hosted on
cdn.kernel.org file servers directly in a "testing"
directory. Therefore the logic that tested for "-rc"
can be removed.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Refreshed all patches.
Altered patches:
- 666-Add-support-for-MAP-E-FMRs-mesh-mode.patch
New symbol for arm targets:
- HARDEN_BRANCH_PREDICTOR
Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Add a basic variant which provides WPA-PSK only, 802.11r and 802.11w and
is intended to support 11r & 11w (subject to driver support) out of the
box.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The tl-wa850re-v2 images from the ar71xx/tiny target are getting too big
with the default packages. The size check is done before the meta data
is added so there is no file to add meta data to or to sign. Originally
errors in Build/append-metadata were getting ignored, but if the signing
fails the error is not ignored.
This adds a check if the file to be signed is there and only does the
signing if it is there. This way it does not fail if the package
creation was already aborted earlier.
Fixes: 848b455d2e ("image: use ucert to append signature")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Sometimes, the CMakeLists.txt file is not in the root directory of a
repo. In those cases, the CMAKE_SOURCE_SUBDIR variable can be specified
to use CMakeLists.txt from a subdirectory instead.
Signed-off-by: Amol Bhave <ambhave@fb.com>
Refreshed all patches.
Added new patch:
- 192-Revert-ubifs-xattr-Don-t-operate-on-deleted-inodes.patch
This fixes a bug introduced in upstream 4.14.68 which caused targets using
ubifs to produce file-system errors on boot, rendering them useless.
Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The current make-ras.sh image generation script for the ZyXEL NBG6617
has portability issues with bash. Because of this, factory images are
currently not built correctly by the OpenWRT buildbots.
This commit replaces the make-ras.sh by C-written mkrasimage.
The new mkrasimage is also compatible with other ZyXEL devices using
the ras image-format.
This is not tested with the NBG6616 but it correctly builds the
header for ZyXEL factory image.
Signed-off-by: David Bauer <mail@david-bauer.net>
The following patch was integrated upstream:
* target/linux/generic/backport-4.9/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch
This fixes tries to work around the following security problems:
* CVE-2018-3620 L1 Terminal Fault OS, SMM related aspects
* CVE-2018-3646 L1 Terminal Fault Virtualization related aspects
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The following patches were integrated upstream:
* target/linux/ipq40xx/patches-4.14/050-0006-mtd-nand-qcom-Add-a-NULL-check-for-devm_kasprintf.patch
* target/linux/mediatek/patches-4.14/0177-phy-phy-mtk-tphy-use-auto-instead-of-force-to-bypass.patch
This fixes tries to work around the following security problems:
* CVE-2018-3620 L1 Terminal Fault OS, SMM related aspects
* CVE-2018-3646 L1 Terminal Fault Virtualization related aspects
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds a tool to generate a firmware file accepted
by Netgear or sercomm devices.
They use a zip-packed rootfs with header and a custom
checksum. The generated Image can be flashed via the
nmrpflash tool or the webinterface of the router.
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
I-O DATA WN-AC1600DGR2 is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.
Specification:
- Qualcomm Atheros QCA9557
- 128 MB of RAM
- 16 MB of Flash
- 2.4/5 GHz wifi
- 2.4 GHz: 2T2R (SoC internal)
- 5 GHz: 3T3R (QCA9880)
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 6x keys (4x buttons, 1x slide switch)
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port of WN-AC1600DGR2
2. Connect power cable to WN-AC1600DGR2 and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Buffalo BHR-4GRV2 is a wired router, based on Qualcomm Atheros
QCA9558.
Ported from ar71xx target.
Specification:
- Qualcomm Atheros QCA9558
- 64 MB of RAM
- 16 MB of Flash
- 5x 10/100/1000 Ethernet
- QCA8337N
- 4x LEDs, 2x keys
- UART header on PCB
- Vcc, TX, RX, GND from LED side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port of BHR-4GRV2
2. Connect power cable to BHR-4GRV2 and turn on it
3. Access to "http://192.168.12.1/" and open firmware update
page ("ファームウェア更新")
4. Select the OpenWrt factory image and click update ("更新実行")
button
5. Wait ~120 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Make sure the Shell-expression returns true also in case of
key-build.ucert being absent.
Fixes commit 848b455d2e ("image: use ucert to append signature")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This reverts commit 42a3c6465a.
The change was apparently never build-tested with all kmods enabled. I took
a brief look but found no simple way to untangle this, so revert it.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Replace the GNU time program invocation with a simple Perl script reporting
the timing values. Since we require Perl anyway for the build system, we can
as well use that instead of requiring a random GNU utility rarely installed
by default.
Fixes: ff6e62b288 ("build: log time taken by each packages/steps")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Refreshed all patches
Remove upstreamed patches.
- 103-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch
- 001-4.11-01-mtd-m25p80-consider-max-message-size-in-m25p80_read.patch
- 001-4.15-08-bcm63xx_enet-correct-clock-usage.patch
- 001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch
- 900-gen_stats-fix-netlink-stats-padding.patch
Introduce a new backported patch to address ext4 breakage, introduced in 4.9.112
- backport-4.9/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch
This patch has been slightly altered to compensate for a new helper function
introduced in later kernels.
Also add ARM64_SSBD symbol to ARM64 targets still running kernel 4.9
Compile-tested on: ar71xx, bcm2710
Runtime-tested on: ar71xx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Fix building packages with LTO when CONFIG_PKG_ASLR_PIE is enabled.
Despite comment of PR lto/80838, it seems that GCC needs -fPIC on linker
command line, even if all objects are -fPIC. This may change as PR
lto/80838 is merged into 8.1
compile-tested: ar71xx, ath79
Fix commits:
6dac92a42e8c11133c9d07940acc34e7397eef69ef16a394d2ef96d1e34a47b42137ce73fc67b614154c0c4006804c51e1e6
Signed-off-by: Julien Dusser <julien.dusser@free.fr>
This partly reverts ca32373c95 which lets
profiles that suppress packages to alter the package selection for all
devices of the target when building with CONFIG_TARGET_PER_DEVICE_ROOTFS.
In particular, this caused the brcm47xx Edimax PS-1208MFG profile to
disable mtd, dropbear, firewall and other essential packages for all
brcm47xx/generic builds.
To solve this problem, prevent profiles from mangling the global
DEFAULT_PACKAGES selection and restrict the supression of negated
packages to the local PACKAGE variable list only.
Fixes ca32373c95 ("target.mk: let profile remove from DEFAULT_PACKAGES")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
On Debian, busybox does have a time applet, but it does not support the -f
flag. Catch this in prereq check to give users to proper error message.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
An incorrect variable name was referenced in KERNEL_FILE_DEPENDS, leading
to the omission of the backport-* patch dirs in the generation of the
prepared stamp name.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Allow enabling/commenting/disabling each feed individually by using a
tristate config symbol.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Setting CONFIG_FEED_... symbols combined two different effects: Disabling
a feed in the generated opkg distfeeds.conf, and omitting the feed from
PACKAGE_SUBDIRS.
It does not make sense to omit built feeds from PACKAGE_SUBDIRS, as it will
only lead to packages that can be enabled in .config (and that will
consequently be built) not to be found during rootfs creation, breaking
the build. All feeds that packages are emitted to should simply always be
added to PACKAGE_SUBDIRS instead; the CONFIG_FEED_... only configure the
generated distfeeds.conf like this.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
build openwrt on centos 6 I should use devtoolset-3 to get gcc 4.9, but
it fail when make menuconfig. so I have to give option HOSTCC='gcc
-Wl,--copy-dt-needed-entries' to make. But it passed to sub make to
HOSTCC=gcc as micro SUBMAKE expand to HOSTCC=gcc
-Wl,--copy-dt-needed-entries. This patch fix this issue.
make -C build menuconfig HOSTCC='gcc -Wl,--copy-dt-needed-entries' V='1'
make: Entering directory `/work/openwrt/openwrt/build'
/opt/rh/devtoolset-3/root/usr/libexec/gcc/x86_64-redhat-linux/4.9.2/ld:
lxdialog/checklist.o: undefined reference to symbol 'acs_map'
//lib64/libtinfo.so.5: error adding symbols: DSO missing from command line
collect2: error: ld returned 1 exit status
make[1]: *** [mconf] Error 1
make -s -C scripts/config all CC=gcc -Wl,--copy-dt-needed-entries: build
failed. Please re-run make with -j1 V=s to see what's going on
make: *** [scripts/config/mconf] Error 1
make: Leaving directory `/work/openwrt/openwrt/build'
Signed-off-by: 李国 <uxgood.org@gmail.com>
Rereshed all patches
Reworked patches to match upstream:
335-v4.16-netfilter-nf_tables-add-single-table-list-for-all-fa.patch
Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
- Make the code more GitHub-specific
- Requires mirror hash to work with .gitattributes
- Use different API depending on whether PKG_SOURCE_VERSION is a
complete commit id or other ref types like tags
- Fix removing symbolic link
- pre-clean dir_untar for possible leftovers from previous run
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Move SCAN_DEPS to scan.mk to eliminate redundancy with scripts/feeds
Add image/*.mk to SCAN_DEPS for targets to pick up newly added devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Seems like the python download.py dl_method call causes serious
performance regression for fresh "make defconfig" as reported in
FS#1621. GitHub tarball download will also be disabled with this
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Add a menuconfig option to set the HOME_URL exposed in
/usr/lib/os-release independent from the
LEDE_DEVICE_MANUFACTURER_URL.
Fixes: FS#1123
Signed-off-by: Mathias Kresin <dev@kresin.me>
A new python script scripts/download.py is added to fetch tarballs using
GitHub archive API [1], then repack in a reproducible way same as the
current DownloadMethod/git
GitHub imposes a 60 reqs/hour rate limit on unauthenticated API
access[2]. This affects fetching commit date for feeding tar --mtime=
argument. However, observation indicates that archive download is NOT
subject to this limit at the moment. In the rare cases where download
fails because of this, we will falback to using DownloadMethod/git
The missing piece in the GitHub API is that it cannot provide in the
tarball dependent submodules's source code. In that case, the
implementation will also fallback to using DownloadMethod/git
[1] Get archive link, https://developer.github.com/v3/repos/contents/#get-archive-link
[2] Rate limiting, https://developer.github.com/v3/#rate-limiting
v2 <- v1:
- allow passing multiple urls with --urls argument
- add commit ts cache. can be helpful on retry
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This patch adds support for ZyXEL NBG6617
Hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR: 32 MiB Macronix MX25L25635F
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS: Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS
Serial:
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
pre-soldered. Pinout:
1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX
first install / debricking / restore stock:
0. Have a PC running a tftp-server @ 192.168.1.99/24
1. connect the PC to any LAN-Ports
2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
into the tftp-server root directory and rename it to just "ras.bin".
3. power-cycle the router and hold down the the WPS button (for 30sek)
4. Wait (for a long time - the serial console provides some progress
reports. The u-boot says it best: "Please be patient".
5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
flashes fast at the same time. You have to reboot the device and
it should then come right up.
Installation via Web-UI:
0. Connect a PC to the powered-on router. It will assign your PC a
IP-address via DHCP
1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
2. Go to the "Expert Mode"
3. Under "Maintenance", select "Firmware-Upgrade"
4. Upload the OpenWRT factory image
5. Wait for the Device to finish.
It will reboot into OpenWRT without any additional actions needed.
To open the ZyXEL NBG6617:
0. remove the four rubber feet glued on the backside
1. remove the four philips screws and pry open the top cover
(by applying force between the plastic top housing from the
backside/lan-port side)
Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:
| Hit any key to stop autoboot: 3
The user is then dropped to a locked shell.
|NBG6617> HELP
|ATEN x[,y] set BootExtension Debug Flag (y=password)
|ATSE x show the seed of password generator
|ATSH dump manufacturer related data in ROM
|ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO boot up whole system
|ATUR x upgrade RAS image (filename)
|NBG6617>
In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!
First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.
|NBG6617> ATSE NBG6617
|012345678901
This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):
- tool.sh -
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -
|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711
copy and paste the result into the shell to unlock zloader.
|NBG6617> ATEN 1,0046B0017430
If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.
|NBG6617> ATGU
|NBG6617#
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Add xt_bpf modules to {kmod-ipt,iptables-mod}-filter.
Match using Linux Socket Filter. Expects a BPF program in decimal
format. This is the format generated by the nfbpf_compile utility.
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Refresh patches.
Remove patch that can be reverse applied:
mvebu/patches-4.14/530-ATA-ahci_mvebu-enable-stop_engine-override.patch
mvebu/patches-4.14/531-ATA-ahci_mvebu-pmp-stop-errata-226.patch
Update patch that no longer applied:
ipq806x/patches-4.14/0035-clk-mux-Split-out-register-accessors-for-reuse.patch
Compiled-tested-for: lantiq, ramips
Run-tested-on: lantiq BT hh5a, ramips MIR3g
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Michael Yartys <michael.yartys@protonmail.com>
Tested-by: Rosen Penev <rosenp@gmail.com>
Busybox time supports the GNU time '-f' syntax used by the build time
logging implemented in ff6e62b288, however the prerequisite check added
only works with GNU time installed as `time` or `gtime`.
As busybox is a multicall binary, the name of the symlink setup by
SetupHostCommand also must be changed from `gtime` to `time` to fix the
value of argv[0]. This causes a number of shells (including bash) to use
their builtin impelementation of time, so the sole invocation has been
changed to use `env time` to use the value found on the $PATH.
Signed-off-by: Andy Boyett <agb@agb.io>
Shorten the version string in Netgear factory image header in order
to enable u-boot TFTP recovery flash mode to work again.
Strip 'r7210-14cb05909a' into 'r7210' in the Netgear image header
by removing the hash (anything after "-").
background:
Some Netgear routers have recently been unable to flash Openwrt
factory image with the TFTP recovery flash mode provided by Netgear
u-boot. That is due to over-long Openwrt version string overflowing
into the router type string in u-boot code. Modern git versions
produce 10-digit short hashes for the Openwrt main repo, and that
causes the version string to be too long in the image header,
breaking the image ID verification by the TFTP flash routine.
(Other option could be to force a shorter hash in scripts/getver.sh,
but as the problem only concerns Netgear routers, let's patch just
them.)
More detailed explanations in FS#1583
Tested with WNDR3800
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Koen Vandeputte
Christian Lamparter
Richard Musil
Felix Fietkau
Hauke Mehrtens
Alexandru Ardelean
Eneas U de Queiroz
Petr Štetiar
Boris Krasnovskiy
Florian Eckert
Daniel Golle
Paul Spooren
Alexander Couzens
Piotr Dymacz
Sven Eckelmann
R. Diez
Michal Hrusecky
Thorsten Glaser
Jeffery To
Oever González
Jo-Philipp Wich
Michal Hrusecky
Stijn Tintel
Mathias Kresin
INAGAKI Hiroshi
Kevin Darbyshire-Bryant
Yousong Zhou
Sebastian Kemper
Brett Mastbergen
Rafał Miłecki
Tomasz Maciej Nowak
Amol Bhave
David Bauer
Daniel Engberg
Ludwig Thomeczek
Rosy Song
Chen Minqiang
Bjørn Mork
Julien Dusser
Matthias Schiffer
李国
Christian Lamparter
Alin Nastac
Andy Boyett
Hannu Nyman