The ZyXEL NBG6617 USB LED was not working with the default images.
It turned out that kmod-usb-ledtrig-usbport was missing from the
default installation.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
In the past, the MX60(W)'s recovery images always had problems
with the size restriction and never really worked without manual
intervention. But starting with 4.19, the MX60(W)'s kernel image
outgrew the allocated space for sysupgrade images as well. Hence
This patch reworks the initramfs, which allows the device to ease
up on the impossible tight kernel size requirements for the
sysupgrade creation and packaging. And as a result, the now
orphaned special ramdisk setup is removed in the process.
This new initramfs can be loaded through the MX60(W) U-boot
in the following way:
=> setenv bootargs console=ttyS0,$baudrate
=> tftpboot $meraki_loadaddr meraki_mx60-initramfs-kernel.bin
[...]
Load address: 0x800000
Loading: ################################################ [...]
done
[...]
=> bootm $fileaddr
\## Booting kernel from Legacy Image at 00800000 ...
...
Updated Flashing instructions for new installations which integrates
the new recovery method. Users of existing installations that only
want to sysupgrade don't need to update their existing u-boot env.
=> setenv owrt_load1 ubi read \${meraki_loadaddr} kernel
=> setenv owrt_load2 ubi read \${meraki_loadaddr} recovery
=> setenv lede_bootkernel bootm \${meraki_loadaddr_kernel} - \${meraki_loadaddr_fdt}
=> setenv owrt_bootkernel bootm \${meraki_loadaddr}
=> setenv owrt_bootargs setenv bootargs console=ttyS0,\${baudrate} rootfstype=squashfs mtdoops.mtddev=oops
=> setenv owrt_boot run meraki_ubi owrt_bootargs\; run owrt_load1 meraki_checkpart lede_bootkernel\; run owrt_load2 owrt_bootkernel
=> setenv bootcmd run owrt_boot
=> saveenv
For more information and the latest flashing guide:
please visit the OpenWrt Wiki Page for the MR60:
<https://openwrt.org/toh/meraki/mx60#flashing>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Based on the process of discovery in
https://github.com/openwrt/openwrt/pull/1613, it has become clear
that (at least) the PowerCloud System CR5000 was unable to get
working 5GHz wireless (PCIe) because AH_USE_EEPROM was unconditionally
masked out, not only when qca,noeeprom was in the DTS.
This patch moves mask AH_USE_EEPROM into the if ... qca,noeeprom
OF test.
Thanks to Christian Lampartar (@chunkeey) for the heavy lifting and help.
Patch has been prepared for upstream and will be submitted after review
by @chunkeey and @xdarklight.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
This commit removes the fixed kernel size-padding for the Netgear
DNI image creation as it is not necessary for a working image.
The fake rootfs still needs to be padded to the blocksize.
Tested-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
GCC 8.0+ <https://gcc.gnu.org/gcc-8/changes.html> introduces a new
warning about unsafe macros expanding to multiple statements used
as a body of a statement such as if, else, while, switch, or for.
In combination with -Werror this can cause the compilation to fail:
|In file included from xmalloc.c:37:
|xmalloc.c: In function 'xmalloc':
|system.h:39:2: error: macro expands to multiple statements [-Werror=multistatement-macros]
| fflush(stdout); \
| ^~~~~~
|xmalloc.c:52:5: note: in expansion of macro 'error'
| error (EXIT_FAILURE, 0, _("memory exhausted"));
| ^~~~~
|xmalloc.c:51:3: note: some parts of macro expansion are not guarded by this 'if' clause
| if (p == NULL)
| ^~
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Without this patch PowerCloud CR5000 AR9382 PCIe 5GHz Wifi uses
the mac address from eeprom instead the one specified when
initializing the PCIe chip. There were two issues:
1) ap94_pci_init on the second PCIe wmac is wrong as there is only one
PCIe wmac on this device (the other wmac is the AR1022/AR9342 SoC wmac).
2) Without specifying pdata->use_eeprom there is a failure to load
firmware and caldata.
Thanks to Christian Lamparter (@chunkeey) for the heavy lifting and
help. [0]
[0] <https://github.com/openwrt/openwrt/pull/1613>
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
67ce93e Fix compile error on kernel 4.15+
c1345bb Change driver version to 10.3.8.0-20181210.
9cb815b Upgrade 88W8997 firmware to 8.4.4.6.
433fc6d Fix non-backport use of nla_parse before 4.12.0
3b36e21 Use wiphy_to_ieee80211_hw() instead of wiphy_priv()
97ebcfa Change driver version to 10.3.8.0-20181120.
f000953 Upgrade 88W8997 firmware to 8.4.4.4.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This patch, in a variety of forms, has been around since beginning 2016
as e756c2bb07, ending up in present form 0aa6c7df60 (kernel 4.4.13 bump)
and carried forward ever since.
There have been a number of MIPS kernel memory handling changes since,
including VDSO fixes that meant openwrt patches have been dropped with
no apparent fallout.
Simple tests (ntfs-3g) on a HIGHMEM 512MB mt7621 device have not turned
up data corruption issues which would otherwise be expected. Similarly
running on other MIPS based devices for the past 2 months hasn't turned
up anything obvious to retain this out of tree patch.
With thanks to Rosen Penev for testing on the known 'highmem' device and
Felix Fietkau for testing advice. Not putting acked-by as it's my fault
if it breaks :-)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Depending on the global nls support configuration in the buildroot, the
linked libelf.so library might depend on libintl.so.
Import the nls.mk helper to set library prefixes and flags accordingly
in this case.
Ref: https://github.com/openwrt/packages/issues/7728#issuecomment-448760140
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
When building with full lagnuage support, libelf.so will depend on and
link with libintl.so so we need to change the pkg-config template to
reflect this library dependency.
Also change the Makefile to only pass --disable-nls to configure when
the full nls support is actually disabled in the buildroot config.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
- it appears (at least from OS X verison 10.10, Yosemite) that the
big and little endian defintions have changed.
the older
#include <sys/_endian.h>
#include <architecture/byte_order.h>
reference yielded the following warning:
#define __bswap_16(x) NXSwapShort(x)
^
/usr/include/architecture/byte_order.h:45:1: note: 'NXSwapShort' has been explicitly marked deprecated here
For the new OS X editions, it seems that we need to refer to:
#include <netinet/in.h>
#include <libkern/OSByteOrder.h>
and respectively use 'OSSwapInt16', 'OSSwapInt32', & 'OSSwapInt64', in
place of 'NXSwapShort', 'NXSwapLong' & 'NXSwapLongLong'.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2efe776 introduces rpath checks with the commit message:
> Remove all rpath entries which do not point to a location below /lib or
> /usr/lib and which do not begin with '$ORIGIN'.
However the implementation failed to support rpath entries with only the
'$ORIGIN' token and no trailing slash, so allow these as well.
Signed-off-by: Yorkie Liu <yazhong.liu@rokid.com>
[reword commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The iproute2 build system links libelf support to every utility while only
the tc program actually requires libelf specific functionality.
Unfortunately the BPF ELF functionality is not confined into an own
compilation unit but added to the existing bpf.c sources of the shared
static libutil.a, causing every iproute2 applet to pick up an implicit
libelf.so dependency.
In order to avoid this requirement, patch the iproute2 build system to
create both a libutil.a and a libutil-elf.a, with the former being built
without libelf functionality and to only link the tc applet with the libelf
enabled libutil.
Finally, make the tc package depend on libelf to solve compilation errors.
Ref: https://github.com/openwrt/packages/issues/7728
Fixes: FS#2011
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Support other packages using pkg-config to query existence and details of
libelf and libdw libraries at build time.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This file is needed to properly use the tc ematch modules present in
kmod-sched-core and kmod-sched. It is a read-only index file of ematch
methods used only by tc.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Patch generation process:
- rebase rpi/rpi-4.14.y on v4.14.89 from linux-stable
- git format-patch v4.14.89
Patches skipped during rebase:
- lan78xx: Read MAC address from DT if present
- lan78xx: Enable LEDs and auto-negotiation
- Revert "softirq: Let ksoftirqd do its job"
- sc16is7xx: Fix for multi-channel stall
- lan78xx: Ignore DT MAC address if already valid
- lan78xx: Simple patch to prevent some crashes
- tcp_write_queue_purge clears all the SKBs in the write queue
- Revert "lan78xx: Simple patch to prevent some crashes"
- lan78xx: Connect phy early
- Arm: mm: ftrace: Only set text back to ro after kernel has been marked ro
- Revert "Revert "softirq: Let ksoftirqd do its job""
- ASoC: cs4265: SOC_SINGLE register value error fix
- Revert "ASoC: cs4265: SOC_SINGLE register value error fix"
- Revert "net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"
- Revert "Revert "net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends""
Patches dropped after rebase:
- net: Add non-mainline source for rtl8192cu wlan
- net: Fix rtl8192cu build errors on other platforms
- brcm: adds support for BCM43341 wifi
- brcmfmac: Mute expected startup 'errors'
- ARM64: Fix build break for RTL8187/RTL8192CU wifi
- ARM64: Enable RTL8187/RTL8192CU wifi in build config
- This is the driver for Sony CXD2880 DVB-T2/T tuner + demodulator
- brcmfmac: add CLM download support
- brcmfmac: request_firmware_direct is quieter
- Sets the BCDC priority to constant 0
- brcmfmac: Disable ARP offloading when promiscuous
- brcmfmac: Avoid possible out-of-bounds read
- brcmfmac: Delete redundant length check
- net: rtl8192cu: Normalize indentation
- net: rtl8192cu: Fix implicit fallthrough warnings
- Revert "Sets the BCDC priority to constant 0"
- media: cxd2880: Bump to match 4.18.y version
- media: cxd2880-spi: Bump to match 4.18.y version
- Revert "mm: alloc_contig: re-allow CMA to compact FS pages"
- Revert "Revert "mm: alloc_contig: re-allow CMA to compact FS pages""
- cxd2880: CXD2880_SPI_DRV should select DVB_CXD2880 with
MEDIA_SUBDRV_AUTOSELECT
- 950-0421-HID-hid-bigbenff-driver-for-BigBen-Interactive-PS3OF.patch
- 950-0453-Add-hid-bigbenff-to-list-of-have_special_driver-for-.patch
Make I2C built-in instead of modular as in upstream defconfig; also the
easiest way to get MFD_ARIZONA enabled, which is required by
kmod-sound-soc-rpi-cirrus.
Add missing compatible strings from
4.9/960-add-rasbperrypi-compatible.patch, using upstream names for
compute modules.
Add extra patch to enable the LEDs on lan78xx.
Compile-tested: bcm2708, bcm2709, bcm2710 (with CONFIG_ALL_KMODS=y)
Runtime-tested: bcm2708, bcm2710
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add kernel module for the fan on the PoE HAT for the 3B+ model in kernel
4.14. Without this, the fan will not turn on.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
It requires sound card support in the new kernel. HDMI CEC support is
disabled for now; enabling it turned out to be non-trivial.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Since kernel 4.12, this driver appeared in staging. The rpi-4.14.y
kernel tree uses these as well.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Support for RaspiDac3 has been removed from the rpi-4.14.y kernel tree.
Make the kmod package depend on kernel 4.9.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Since kernel 4.12, this driver appeared in staging. The rpi-4.14.y
kernel tree uses these as well.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
We need to use resolved file list as prerequisites for repacking kmod
.ipk files. Note that currently version_filter uses a Makefile macro
KERNEL_PATCHVER that should be available at ipk building time.
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The LS1021A-IoT gateway reference design based on the
QorIQ LS1021A processor is a purpose-built, small
footprint hardware platform with a wide array of
high-speed connectivity and low-speed serial interfaces
to support secure delivery of IoT services for home,
business or other commercial location.
- Combines standards-based, open source software with a
feature-rich IoT gateway design to establish a common,
open framework for secured IoT service delivery and
management.
- Provides a wide assortment of high-speed and serial-based
connectivity in a compact, highly secure design.
- High efficiency through the use of the Arm-based QorIQ
LS1021A embedded processor.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
This patch is to upgrade kernel to 4.14 for layerscape.
patches-4.14 for layerscape included two categories.
- NXP Layerscape SDK kernel-4.14 patches
All patches on tag LSDK-18.09-V4.14 were ported to OpenWrt
kernel. Since there were hundreds patches, we had to make
an all-in-one patch for each IP/feature.
See below links for LSDK kernel.
https://lsdk.github.io/components.htmlhttps://source.codeaurora.org/external/qoriq/qoriq-components/linux
- Non-LSDK kernel patches
Other patches which were not in LSDK were just put in patches-4.14.
Kept below patches from patches-4.9.
303-dts-layerscape-add-traverse-ls1043.patch
821-add-esdhc-vsel-to-ls1043.patch
822-rgmii-fixed-link.patch
Renamed and rebase them as below in patches-4.14,
303-add-DTS-for-Traverse-LS1043-Boards.patch
712-sdk-dpaa-rgmii-fixed-link.patch
824-mmc-sdhci-of-esdhc-add-voltage-switch-support-for-ls.patch
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
While building 4.19 for ath79 with CONFIG_ALL_KMODS=y with verbose mode
enabled I was asked by kernel config about few symbols/modules so I'm
adding those missing symbols to the generic config.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It seems, that since Linux 4.18-rc2 ci_hdrc depends on ulpi.
commit a930d8bd94d8db7715d1af74299f710b1fb22fc8
Author: Fabio Estevam <fabio.estevam@nxp.com>
Date: Wed Jul 4 10:09:58 2018 -0300
usb: chipidea: Always build ULPI code
Commit 03e6275ae381 ("usb: chipidea: Fix ULPI on imx51") causes a kernel
hang on imx51 systems that use the ULPI interface and do not select the
CONFIG_USB_CHIPIDEA_ULPI option.
In order to avoid such potential misuse, let's always build the
chipidea ULPI code into the final ci_hdrc object.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
After changing board names to DT compat string, we also need to
adjust the script which generates uboot-env configuration files.
Fixes: e880a30549 ("mxs: use generic sysinfo board detection")
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
According to https://github.com/openwrt/openwrt/pull/1527, support
for the Buffalo BHR-4GRV2 in ath79 requires repartitioning from
an initramfs image, make this easier by supporting uboot-envtools
support out of the box.
Build tested, but not runtime tested.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Port support for the Buffalo WZR-HP-AG300H from the ar71xx target to
ath79 as well.
Build- and runtime tested on the Buffalo WZR-HP-AG300H.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Interface triggers are installed by the dropbear init script in case an
interface is configured for a given dropbear uci section.
As dropbear is started after network the interface trigger event can be
missed during a small window; this is especially the case if lan is
specified as interface.
Fix this by starting dropbear before network so no interface trigger
is missed. As dropbear is started earlier than netifd add a boot function
to avoid the usage of network.sh functions as call to such functions will
fail at boottime.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Originally, cns3xxx used it's own functions for mapping, reading and writing registers.
Upstream commit 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config accessors")
removed the internal PCI config write function in favor of the generic one:
cns3xxx_pci_write_config() --> pci_generic_config_write()
cns3xxx_pci_write_config() expected aligned addresses, being produced by cns3xxx_pci_map_bus()
while the generic one pci_generic_config_write() actually expects the real address
as both the function and hardware are capable of byte-aligned writes.
This currently leads to pci_generic_config_write() writing
to the wrong registers on some ocasions.
First issue seen due to this:
- driver ath9k gets loaded
- The driver wants to write value 0xA8 to register PCI_LATENCY_TIMER, located at 0x0D
- cns3xxx_pci_map_bus() aligns the address to 0x0C
- pci_generic_config_write() effectively writes 0xA8 into register 0x0C (CACHE_LINE_SIZE)
This seems to cause some slight instability when certain PCI devices are used.
Another issue example caused by this this is the PCI bus numbering,
where the primary bus is higher than the secondary, which is impossible.
Before:
00:00.0 PCI bridge: Cavium, Inc. Device 3400 (rev 01) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 255
Bus: primary=02, secondary=01, subordinate=ff, sec-latency=0
After fix:
00:00.0 PCI bridge: Cavium, Inc. Device 3400 (rev 01) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 255
Bus: primary=00, secondary=01, subordinate=02, sec-latency=0
And very likely some more ..
Fix all by omitting the alignment being done in the mapping function.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Deng Qingfang
Christian Lamparter
Daniel F. Dickinson
Hans Dedecker
David Bauer
Koen Vandeputte
Jo-Philipp Wich
Kevin Darbyshire-Bryant
Yorkie Liu
Tony Ambardar
Stijn Tintel
Yousong Zhou
Yangbo Lu
Biwen Li
Petr Štetiar
Michael Heimpold
Stefan Lippers-Hollmann