Commit Graph

44922 Commits (7d96c301d6afc9f360c26b404e435e8e03c1e207)

Author SHA1 Message Date
Yousong Zhou e51b513f75 opkg: bump to version 2019-06-14
Opkg starting from this version special-cases busybox as alternatives
provider.  There should be no need to add entries to ALTERNATIVES of
busybox package

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2019-06-14 01:51:24 +00:00
Stijn Tintel 09c6885ce7 kernel: add missing symbol to 4.19 config
Kernel 4.19.47 added a new kernel config symbol ARM64_ERRATUM_1463225.
This causes a build failure for sunxi/cortexa53. Add the symbol to the
generic config to fix this, and avoid future build failures on other
arm64 targets that expose this symbol. As the erratum only affects
Cortex-A76 cores, we can safely disable it.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2019-06-14 01:24:56 +03:00
Hans Dedecker 55fcc77072 netifd: update to latest git HEAD
42a3878 interface-ip: fix possible null pointer dereference
c1964d8 system-linux: remove superfluous dev check

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2019-06-13 22:18:57 +02:00
Kevin Darbyshire-Bryant ff2382e36c ath10k-firmware: update Candela Tech firmware images
wave-1:

2019-05-09: Tweak rate-ctrl:  Ramp PER up faster, down slower.  This
	    helps throughput in rate-vs-range test, especially with
	    nss1.

2019-05-20: Disable adaptive-CCA.  I am not sure it helps, and it may
	    make it slower to detect noise that should tell the system
	    to stop transmitting.  If someone has means to test this
	    properly, I'd be happy to work with them.

wave-2:

2019-05-15: Fix problem where rate-ctrl sometimes used rix of 0x0.

2019-05-15: Allow raw-tx of encrypted frame.  Requires a patch to the
	    driver to use raw mode when skb has WEP flag enabled AND
	    skb is flagged to not be encrypted.  Lightly tested.

2019-05-16: Fix tx-hang that happened when rate-ctrl chose an OFDM rate
	    for 20Mhz and sent that as AMPDU.  To fix, limit to (V)HT
	    rates if peer is (V)HT.  It seems that MCS0 (V)HT20 should
	    have as good of a chance of being detected as CCK or OFDM.

2019-06-06: Disable TX-BFEE, TX-BFER for IBSS connections.  I suspect
	    this is part of the tx-hang issue seen with IBSS between
	    two 9984 radios.

2019-06-12: Fix rx-rate reporting in 'fw_stats' logic.  This was at
	    least partly due to regressions I had added earlier when
	    working on some multi-vdev enhancements.

2019-6-12: Fix case where extd peer-stats were not always populated.
	   The stats gathering code did not handle error conditions
	   well.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2019-06-13 19:35:19 +01:00
Kevin Darbyshire-Bryant 49b3dcb2ab ath10k-ct: Update to 2019-06-13
Changes:

ath10k:  Improve PMF/MPF mgt frame check

And add a driver for 5.2 (beta, not even tested yet) kernel.

Refresh patches.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2019-06-13 19:35:19 +01:00
Paul Spooren 35a70d6262 f2fs-tools: fixup SPDX license
The f2fs-tools have a wrong PKG_LICENSE with is not SPDX compatible.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-06-12 23:55:53 +02:00
Daniel Golle fcb41decf6 config: enable some useful features on !SMALL_FLASH devices
enable kernel features needed for procd-ujail, procd-seccomp, lxc and
more on devices with big enough flash. Those packages are currently
useless in binary builds due to missing kernel features.
Enable the features on devices which can bare with the extra space
consumption.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-06-12 23:33:45 +02:00
Konstantin Demin 38b22b1e70 nghttp2: deduplicate files in libnghttp2
libnghttp2 accidentally ships library twice:

$ tar -Oxzf libnghttp2-14_1.38.0-1_mips_24kc.ipk ./data.tar.gz | tar -tzvf -
drwxr-xr-x root/root         0 2019-06-07 23:14 ./
drwxr-xr-x root/root         0 2019-06-07 23:14 ./usr/
drwxr-xr-x root/root         0 2019-06-07 23:14 ./usr/lib/
-rw-r--r-- root/root    144412 2019-06-07 23:14 ./usr/lib/libnghttp2.so.14
-rw-r--r-- root/root    144412 2019-06-07 23:14 ./usr/lib/libnghttp2.so.14.17.3

after fix, there's library and symlink (as designed):

$ tar -Oxzf libnghttp2-14_1.38.0-2_mips_24kc.ipk ./data.tar.gz | tar -tzvf -
drwxr-xr-x root/root         0 2019-06-07 23:14 ./
drwxr-xr-x root/root         0 2019-06-07 23:14 ./usr/
drwxr-xr-x root/root         0 2019-06-07 23:14 ./usr/lib/
lrwxrwxrwx root/root         0 2019-06-07 23:14 ./usr/lib/libnghttp2.so.14 -> libnghttp2.so.14.17.3
-rw-r--r-- root/root    144412 2019-06-07 23:14 ./usr/lib/libnghttp2.so.14.17.3

Binary package size reduced accordingly: 134621 -> 66593.

Compile/run-tested: ar71xx/generic.

Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
2019-06-12 23:00:58 +02:00
Koen Vandeputte c12bd3a21b iwinfo: update to latest git HEAD
1372f47eff34 iwinfo: Add Mikrotik R11e-5HnDr2

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-12 15:04:09 +02:00
Koen Vandeputte 11b4d29ef5 kernel: bump 4.19 to 4.19.50
Refreshed all patches.

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-12 15:04:09 +02:00
Koen Vandeputte a7e68927d0 kernel: bump 4.14 to 4.14.125 (FS#2305 FS#2297)
Refreshed all patches.

This bump contains upstream commits which seem to avoid (not properly fix)
the errors as seen in FS#2305 and FS#2297

Altered patches:
- 403-net-mvneta-convert-to-phylink.patch
- 410-sfp-hack-allow-marvell-10G-phy-support-to-use-SFP.patch

Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-12 15:04:09 +02:00
Koen Vandeputte f2f7cc67e5 kernel: bump 4.9 to 4.9.181
Refreshed all patches.

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-12 15:04:09 +02:00
Yousong Zhou 04b45d3a31 dnsmasq: move feature detection inside a shell func
Resolves 

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2019-06-11 08:32:54 +00:00
Petr Štetiar f5387b754f build: add urandom-seed and urngd to default packages set
urandom-seed content was split from base-files into separate package so
in order to preserve the current functionality and to provide some
fallback mechanism in case jent-rng initialization fails in urngd we
need to add it back.

urngd is OpenWrt's micro non-physical true random number generator based
on timing jitter.

Tested-by: Lucian Cristian <lucian.cristian@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-11 08:06:28 +02:00
Petr Štetiar 27bfde9c9f base-files: move urandom seed bits into separate package
So it's possible to install or remove it as needed.

Tested-by: Lucian Cristian <lucian.cristian@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-11 08:06:28 +02:00
Petr Štetiar 9b4de712ca ubox: move getrandom into separate getrandom package
So it's possible to install or remove it as needed.

Tested-by: Lucian Cristian <lucian.cristian@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-11 08:06:28 +02:00
Petr Štetiar 714bd89fce urng: add micro non-physical true RNG based on timing jitter
μrngd is OpenWrt's micro non-physical true random number generator based
on timing jitter.

Using the Jitter RNG core, the rngd provides an entropy source that
feeds into the Linux /dev/random device if its entropy runs low. It
updates the /dev/random entropy estimator such that the newly provided
entropy unblocks /dev/random.

The seeding of /dev/random also ensures that /dev/urandom benefits from
entropy. Especially during boot time, when the entropy of Linux is low,
the Jitter RNGd provides a source of sufficient entropy.

Tested-by: Lucian Cristian <lucian.cristian@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-11 08:06:28 +02:00
Alexander Couzens c53f62b111
version.mk: use https:// instead of http://
Only the repo should not use https. Otherwise the build would need
a wget/uclient_fetch with tls support.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2019-06-11 01:49:44 +02:00
Alexander Couzens 79948e9d61
replace links towards lede-project.org with openwrt.org
Modify VERSION_SUPPORT_URL VERSION_REPO
Replace BUGS variable in toolchain/gcc/common.mk

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2019-06-11 01:46:53 +02:00
Karl Pálsson 3b36aae9d5 toolchain: replace LEDE in help text
Use generic wording.

Signed-off-by: Karl Pálsson <karlp@etactica.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [fixed a -> á]
2019-06-10 11:31:52 +02:00
Kristian Evensen 86b6d31e6e ramips: Remove redundant LED-cases
01_leds has several redundant LED-cases. This commit cleans
up the file by merging these cases into shared cases.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-06-10 11:25:47 +02:00
Adrian Schmutzler fde0abf267 ath79: Add support for TP-Link Archer C25 v1
The TP-Link Archer C25 is a low-cost dual-band router.

Specification:

- CPU: Atheros QCA9561 775 MHz
- RAM: 64 MB
- Flash: 8 MB
- Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887
- NET: 5x 10/100 Mbps Ethernet

Some LEDs are controlled by an additional 74HC595 chip, but not
all of them as e.g. for the C59.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-06-10 11:25:47 +02:00
Adrian Schmutzler 409940cef4 ath79: Reorder some TP-Link Archer devices in 01_leds
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-06-10 11:25:47 +02:00
Deng Qingfang b47cf6d539 ramips: mt7620: select kmod-rt2800-pci driver for RT5592
ASUS RP-N53 and Buffalo WHR-600D use RT5592 for 5GHz wireless
After commit 367813b9b1 the driver for RT5592 (rt2800pci)
is not selected by default anymore, which broke their 5GHz wireless
Add it back to device packages

Fixes: 367813b9b1 ("ramips: mt7620: fix dependencies")

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2019-06-10 11:25:47 +02:00
David Santamaría Rogado e19506f206 ath79: migrate Archer C7 5GHz radio device paths
When upgrading a TP-Link Archer C7 v2 from ar71xx to ath79,
the 5ghz radio stops working because the device path changed.

Some people subtitute the unsupported QCA9880v1 in the Archer v1
with supported QCA9880v2 radio. Since the stock radio doesn't
work, so it's safe to apply the change also for the Archer v1
images as well.

Also this patch renames the migration file and variables from
wmac to wifi.

Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[removed comment, added return 0 (not that it matters since uci is
clever, see 00-wmac-migration thread), reworded commit message]
2019-06-10 11:25:46 +02:00
Adrian Schmutzler fcb920ffe7 ath79: Consistently label art partition with lower case
This patch harmonizes the label and alias for art partitions
across ath79. Since lower case seems to be more frequent, use that
consistently.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-06-10 11:25:41 +02:00
Adrian Schmutzler 4d807ad2d9 ath79: Read MAC addresses from flash in 11-ath10k-caldata
In commit c3a8518 eth0 and eth1 have been swapped for some devices,
but 11-ath10k-caldata has not been updated.
Instead of fixing this by swapping eth0/eth1, this patch will read
addresses from flash (as done for several devices already) so
adjustments due to eth order become obsolete.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-06-10 11:25:41 +02:00
Adrian Schmutzler 3d153323ab ath79: Consistently label info partition
The info/product-info partition, which frequently contains MAC
adresses, is typically assigned the 'info' alias in DTS, but
then labelled with 'info', 'product-info' or 'config'.

This leads to different aliases if used for setting MAC adresses
in DTS compared to when using e.g. mtd_get_mac_binary. Occationally,
also multiple switch-case entries are used just because of different
labelling.

This patch relabels those partitions in ath79 to consistently use
'info'.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-06-10 11:25:41 +02:00
Pawel Dembicki c4fdd4979b mpc85xx: re-enable TL-WDR4900v1 images
This reverts commit 324e94f31b ("mpc85xx: disable bricking TL-WDR4900v1 images")

The previous commit fixes the TL-WDR4900v1. Enable the target again.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-06-10 11:21:35 +02:00
Christian Lamparter 1e41de2f48 mpc85xx: convert TL-WDR4900 v1 to simpleImage
Converts the TP-Link WDR4900 v1 to use the simpleImage in the
hopes of prolonging the life of the device. While at it,
the patch makes the fdt.bin an ARTIFACT and sets the KERNEL_SIZE
to 2684 KiB as a precaution since the stock u-boot is using a
fixed kernel size.

Note: Give the image some time, it will take much longer to
extract and boot.

[tested for 4.14/4.19]

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Co-authored-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-06-10 11:21:35 +02:00
André Valentin 452d88e8f7 config: add xfrm interface support scripts
This package adds scripts for xfrm interfaces support.
Example configuration via /etc/config/network:

config interface 'xfrm0'
        option proto 'xfrm'
        option mtu '1300'
        option zone 'VPN'
        option tunlink 'wan'
        option ifid 30

config interface 'xfrm0_static'
        option proto 'static'
        option ifname '@xfrm0'
        option ip6addr 'fe80::1/64'
        option ipaddr '10.0.0.1/30'

Now set in strongswan IPsec policy:
 	if_id_in = 30
	if_id_out = 30

Signed-off-by: André Valentin <avalentin@marcant.net>
2019-06-10 10:07:24 +02:00
Hans Dedecker cc092a285a curl: update to 7.65.1
For changes in 7.65.1; see https://curl.haxx.se/changes.html#7_65_1

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2019-06-10 10:06:05 +02:00
André Valentin ae3e232b11 netsupport: add xfrmi interface support
Add support for xfrm interfaces in kernel. XFRM interfaces are used by
the IPsec stack for tunneling.
XFRM interfaces are available since linux 4.19.

Signed-off-by: André Valentin <avalentin@marcant.net>
2019-06-09 21:48:22 +02:00
Petr Štetiar 0e1d07af1d kirkwood: image: fix unwanted 2nd inclusion of kernel
In commit d2e18dae28 ("kirkwood: cleanup image build code") the image
build code was refactored, setting KERNEL_IN_UBI=0 which doesn't work as
the KERNEL_IN_UBI needs to be unset in order to make it working as
intended, which leads to factory images with two kernels in them:

 binwalk --keep-going openwrt-kirkwood-cisco_on100-squashfs-factory.bin
 MD5 Checksum:  c33e3d1eb0cb632bf0a4dc287592eb70
 DECIMAL   	HEX       	DESCRIPTION
 -------------------------------------------------------------------------------
 0         	0x0       	uImage header [...] "ARM OpenWrt Linux-4.14.123"
 5769216   	0x580800  	uImage header [...] "ARM OpenWrt Linux-4.14.123"

Cc: Mathias Kresin <dev@kresin.me>
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=2285
Fixes: d2e18dae28 ("kirkwood: cleanup image build code")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-09 14:51:47 +02:00
Petr Štetiar 6c5bfaac84 gpio-button-hotplug: gpio-keys: fix always missing first event
Commit afc056d7dc ("gpio-button-hotplug: support interrupt
properties") changed the gpio-keys interrupt handling logic in a way,
that it always misses first event, which causes issues with rc.button
scripts, so this patch restores the previous behaviour.

Fixes: afc056d7dc ("gpio-button-hotplug: support interrupt properties")
Reported-by: Kristian Evensen <kristian.evensen@gmail.com>
Tested-by: Kuan-Yi Li <kyli.tw@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [drop state check]
2019-06-09 14:51:47 +02:00
Petr Štetiar 27d234a345 gpio-button-hotplug: fix wrong initial seen value
Currently the generated event contains wrong seen value, when the button
is pressed for the first time:

 rmmod gpio_button_hotplug; modprobe gpio_button_hotplug
 [ pressing the wps key immediately after modprobe ]
 gpio-keys: create event, name=wps, seen=1088, pressed=1

So this patch adds a check for this corner case and makes seen=0 if the
button is pressed for the first time.

Tested-by: Kuan-Yi Li <kyli.tw@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-09 14:51:47 +02:00
Petr Štetiar 33ccfe0e14 gpio-button-hotplug: use pr_debug and pr_err
pr_debug can be used with dynamic debugging.

Tested-by: Kuan-Yi Li <kyli.tw@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-09 14:51:47 +02:00
Yousong Zhou 0299a4b73e dnsmasq: skip options that are not compiled in
This is to make life easier for users with customized build of
dnsmasq-full variant.  Currently dnsmasq config generated by current
service script will be rejected by dnsmasq build lacking DHCP feature

 - Options like --dhcp-leasefile have default values.  Deleting them
   from uci config or setting them to empty value will make them take on
   default value in the end
 - Options like --dhcp-broadcast are output unconditionally

Tackle this by

 - Check availablility of features from output of "dnsmasq --version"
 - Make a list of options guarded by HAVE_xx macros in src/options.c of
   dnsmasq source code
 - Ignore these options in xappend()

Two things to note in this implementation

 - The option list is not exhaustive.  Supposedly only those options that
   may cause dnsmasq to reject with "unsupported option (check that
   dnsmasq was compiled with DHCP/TFTP/DNSSEC/DBus support)" are taken
   into account here
 - This provides a way out but users' cooperation is still needed.  E.g.
   option dnssec needs to be turned off, otherwise the service script
   will try to add --conf-file pointing to dnssec specific anchor file
   which dnsmasq lacking dnssec support will reject

Resolves FS#2281

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2019-06-09 08:17:52 +00:00
Hans Dedecker 6b762dd75f netifd: xfrm tunnel support
8c6358b netifd: add xfrm tunnel interface support

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2019-06-08 21:51:37 +02:00
Konstantin Demin 10011f91c5 busybox: add ALTERNATIVES for brctl
Busybox brctl applet conflicts with the version from bridge-utils.
Fix this by using ALTERNATIVE support for brctl in busybox.

Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
2019-06-08 13:51:40 +02:00
Deng Qingfang 0f4e65ec7b tools/ccache: update to 3.7.1
Update ccache to 3.7.1

Release notes:
https://ccache.dev/releasenotes.html#_ccache_3_7_1

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2019-06-08 09:59:25 +02:00
Chen Minqiang de1431b589 kernel: re-add bridge allow reception on disabled port
The "bridge allow reception on disabled port" implementation
was broken after these commits:

08802d93e2 ("kernel: bump 4.19 to 4.19.37")
b765f4be40 ("kernel: bump 4.14 to 4.14.114")
456f486b53 ("kernel: bump 4.9 to 4.9.171")

This leads to issues when for example WDS is used, tied to a bridge:

[ 96.503771] wlan1: send auth to d4:5f:25:eb:09:82 (try 1/3)
[ 96.517956] wlan1: authenticated
[ 96.526209] wlan1: associate with d4:5f:25:eb:09:82 (try 1/3)
[ 97.086156] wlan1: associate with d4:5f:25:eb:09:82 (try 2/3)
[ 97.200919] wlan1: RX AssocResp from d4:5f:25:eb:09:82 (capab=0x11 status=0 aid=1)
[ 97.208706] wlan1: associated
[ 101.312913] wlan1: deauthenticated from d4:5f:25:eb:09:82 (Reason: 2=PREV_AUTH_NOT_VALID)

It seems upstream introduced a new patch, [1]
so we have to reimplement these patches properly:

target/linux/generic/pending-4.9/150-bridge_allow_receiption_on_disabled_port.patch
target/linux/generic/pending-4.14/150-bridge_allow_receiption_on_disabled_port.patch
target/linux/generic/pending-4.19/150-bridge_allow_receiption_on_disabled_port.patch

[1] https://lkml.org/lkml/2019/4/24/1228

Fixes: 08802d93e2 ("kernel: bump 4.19 to 4.19.37")
Fixes: b765f4be40 ("kernel: bump 4.14 to 4.14.114")
Fixes: 456f486b53 ("kernel: bump 4.9 to 4.9.171")
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
[updated commit message and title]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-07 18:22:20 +02:00
Kevin Darbyshire-Bryant 021a9b4cb9 iproute2: add tc action ctinfo support
Add the userspace control portion of the backported kernelspace
act_ctinfo.

ctinfo is a tc action restoring data stored in conntrack marks to
various fields.  At present it has two independent modes of operation,
restoration of DSCP into IPv4/v6 diffserv and restoration of conntrack
marks into packet skb marks.

It understands a number of parameters specific to this action in
additional to the usual action syntax.  Each operating mode is
independent of the other so all options are optional, however not
specifying at least one mode is a bit pointless.

Usage: ... ctinfo [dscp mask [statemask]] [cpmark [mask]] [zone ZONE]
		  [CONTROL] [index <INDEX>]

DSCP mode

dscp enables copying of a DSCP stored in the conntrack mark into the
ipv4/v6 diffserv field.  The mask is a 32bit field and specifies where
in the conntrack mark the DSCP value is located.  It must be 6
contiguous bits long. eg. 0xfc000000 would restore the DSCP from the
upper 6 bits of the conntrack mark.

The DSCP copying may be optionally controlled by a statemask.  The
statemask is a 32bit field, usually with a single bit set and must not
overlap the dscp mask.  The DSCP restore operation will only take place
if the corresponding bit/s in conntrack mark ANDed with the statemask
yield a non zero result.

eg. dscp 0xfc000000 0x01000000 would retrieve the DSCP from the top 6
bits, whilst using bit 25 as a flag to do so.  Bit 26 is unused in this
example.

CPMARK mode

cpmark enables copying of the conntrack mark to the packet skb mark.  In
this mode it is completely equivalent to the existing act_connmark
action.  Additional functionality is provided by the optional mask
parameter, whereby the stored conntrack mark is logically ANDed with the
cpmark mask before being stored into skb mark.  This allows shared usage
of the conntrack mark between applications.

eg. cpmark 0x00ffffff would restore only the lower 24 bits of the
conntrack mark, thus may be useful in the event that the upper 8 bits
are used by the DSCP function.

Usage: ... ctinfo [dscp mask [statemask]] [cpmark [mask]] [zone ZONE]
		  [CONTROL] [index <INDEX>]
where :
	dscp MASK is the bitmask to restore DSCP
	     STATEMASK is the bitmask to determine conditional restoring
	cpmark MASK mask applied to restored packet mark
	ZONE is the conntrack zone
	CONTROL := reclassify | pipe | drop | continue | ok |
		   goto chain <CHAIN_INDEX>

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2019-06-07 12:05:32 +01:00
Kevin Darbyshire-Bryant b8a72dfd28 kernel: backport act_ctinfo
ctinfo is a new tc filter action module.  It is designed to restore
information contained in firewall conntrack marks to other packet fields
and is typically used on packet ingress paths.  At present it has two
independent sub-functions or operating modes, DSCP restoration mode &
skb mark restoration mode.

The DSCP restore mode:

This mode copies DSCP values that have been placed in the firewall
conntrack mark back into the IPv4/v6 diffserv fields of relevant
packets.

The DSCP restoration is intended for use and has been found useful for
restoring ingress classifications based on egress classifications across
links that bleach or otherwise change DSCP, typically home ISP Internet
links.  Restoring DSCP on ingress on the WAN link allows qdiscs such as
but by no means limited to CAKE to shape inbound packets according to
policies that are easier to set & mark on egress.

Ingress classification is traditionally a challenging task since
iptables rules haven't yet run and tc filter/eBPF programs are pre-NAT
lookups, hence are unable to see internal IPv4 addresses as used on the
typical home masquerading gateway.  Thus marking the connection in some
manner on egress for later restoration of classification on ingress is
easier to implement.

Parameters related to DSCP restore mode:

dscpmask - a 32 bit mask of 6 contiguous bits and indicate bits of the
conntrack mark field contain the DSCP value to be restored.

statemask - a 32 bit mask of (usually) 1 bit length, outside the area
specified by dscpmask.  This represents a conditional operation flag
whereby the DSCP is only restored if the flag is set.  This is useful to
implement a 'one shot' iptables based classification where the
'complicated' iptables rules are only run once to classify the
connection on initial (egress) packet and subsequent packets are all
marked/restored with the same DSCP.  A mask of zero disables the
conditional behaviour ie. the conntrack mark DSCP bits are always
restored to the ip diffserv field (assuming the conntrack entry is found
& the skb is an ipv4/ipv6 type)

e.g. dscpmask 0xfc000000 statemask 0x01000000

|----0xFC----conntrack mark----000000---|
| Bits 31-26 | bit 25 | bit24 |~~~ Bit 0|
| DSCP       | unused | flag  |unused   |
|-----------------------0x01---000000---|
      |                   |
      |                   |
      ---|             Conditional flag
         v             only restore if set
|-ip diffserv-|
| 6 bits      |
|-------------|

The skb mark restore mode (cpmark):

This mode copies the firewall conntrack mark to the skb's mark field.
It is completely the functional equivalent of the existing act_connmark
action with the additional feature of being able to apply a mask to the
restored value.

Parameters related to skb mark restore mode:

mask - a 32 bit mask applied to the firewall conntrack mark to mask out
bits unwanted for restoration.  This can be useful where the conntrack
mark is being used for different purposes by different applications.  If
not specified and by default the whole mark field is copied (i.e.
default mask of 0xffffffff)

e.g. mask 0x00ffffff to mask out the top 8 bits being used by the
aforementioned DSCP restore mode.

|----0x00----conntrack mark----ffffff---|
| Bits 31-24 |                          |
| DSCP & flag|      some value here     |
|---------------------------------------|
			|
			|
			v
|------------skb mark-------------------|
|            |                          |
|  zeroed    |                          |
|---------------------------------------|

Overall parameters:

zone - conntrack zone

control - action related control (reclassify | pipe | drop | continue |
ok | goto chain <CHAIN_INDEX>)

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make suitable adjustments for backporting to 4.14 & 4.19
and add to SCHED_MODULES_FILTER

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2019-06-06 15:41:07 +01:00
Biwen Li 5159d71983 layerscape: update patches-4.14 to LSDK 19.03
All patches of LSDK 19.03 were ported to Openwrt kernel.
We still used an all-in-one patch for each IP/feature for
OpenWrt.

Below are the changes this patch introduced.
- Updated original IP/feature patches to LSDK 19.03.
- Added new IP/feature patches for eTSEC/PTP/TMU.
- Squashed scattered patches into IP/feature patches.
- Updated config-4.14 correspondingly.
- Refreshed all patches.

More info about LSDK and the kernel:
- https://lsdk.github.io/components.html
- https://source.codeaurora.org/external/qoriq/qoriq-components/linux

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2019-06-06 15:40:09 +02:00
Biwen Li 639d127b83 layerscape: fix u-boot bootcmd
Current latest LSDK-19.03 u-boot had a bug that bootcmd
environment was always been reset when u-boot started up.
This was found on boards with spi NOR boot. Before the
proper fix-up is applied, we have to use a workaround
to hard code the bootcmd for OpenWrt booting for now.

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2019-06-06 15:40:09 +02:00
Yangbo Lu 8468bf04d0 layerscape: drop ppa package
Drop ppa package since TF-A is used instead.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2019-06-06 15:40:09 +02:00
Biwen Li c07d3302b3 layerscape: convert to use TF-A for firmware
This patch is to convert to use TF-A for firmware.
- Use un-swapped rcw since swapping will be done in TF-A.
- Use u-boot with TF-A defconfig.
- Rework memory map for TF-A introduction.

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2019-06-06 15:40:09 +02:00
Biwen Li 17dcbe1b8e layerscape: add ARM Trusted Firmware package
Add TF-A packages for Layerscape to implement trusted firmware.

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2019-06-06 15:40:08 +02:00
Biwen Li f7f1f39c34 layerscape: add rcw packages for ls1043ardb/ls1046ardb SD boot
Add rcw packages for ls1043ardb/ls1046ardb SD boot.

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2019-06-06 15:40:08 +02:00