Boot Loaders submenu of Utilities is the most logical place to find rbcfg and other bootloader tools.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
The special prefix of "/" should match any url by definition but the final
assertion which ensures that the matched prefix ends in '\0' or '/' is causing
matches against the "/" prefix to fail.
Update to current HEAD in order to fix this particular case.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This helper allows using usbport trigger directly. It requires usbport
compatible syntax and supports specifying multiple USB ports, e.g.:
ucidef_set_led_usbport "usb" "USB" "devicename:colour:function" "usb1-port1" "usb2-port1"
This adds a proper object to the board.json, e.g.
"usb": {
"name": "USB",
"type": "usbport",
"sysfs": "devicename:colour:function",
"ports": [
"usb1-port1",
"usb2-port1"
]
}
and supports translating it into uci section.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* Adjust download locations:
- use https as busybox.net permanently redirects http to https
- gentoo mirror has neither 1.25.0 nor 1.25.1 available, so drop it
in favor of buildroot.net that has 1.25.1
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* Backport much of the 10.2 firmware features from upstream QCA driver.
This includes ANI support, adaptive CCA, tx-hang workarounds,
and lots of other things.
Not all of this may be enabled at this point, and more code waits to
be backported as time and motivation allows.
* Fix some rate-control issues where ath10k in station mode (at least), would
sometimes get stuck at low rates. This appeared to be a probe related
state machine issue in the firmware, so I added some timeout logic to kick
the state machine if it gets stuck. This signicantly improves throughput
tests with many stations.
* Support configuring WMI WD timeout using SET_SPECIAL API.
* Properly configure the rx-mask on bootup to work around problem found
by Mr. Kazior. This should remove the need to add the driver hack he
posted.
* Allow configuring pdev failed-retry threshold. This is how many consecutive
tx failures the firmware will allow before resetting the wifi chip (not a full
firmware crash).
Signed-off-by: Ben Greear <greearb@candelatech.com>
Adds Sebastian's 160Mhz support (un-tested), remove DMA32 change that
broke some x86 systems, allow setting 10.1 CT firmware keepalive watchdog
timeout, support QCA 9887 hardware, and some other tweaks.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This is upstream alternative for LEDE's ledtrig-usbdev. It's main
advantages are:
1) Support for assigning more than 1 USB port to the LED
2) Setting proper state when activating with device already connected
3) FWIW it's an upstream driver
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
changed install path from /sbin to /usr/sbin to be consistent with other filesystem tools
ext2-3-4 and f2fs tools are in /usr/sbin, for example
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
iperf upstream added some bugfixes to the already released 2.0.9 version
without changing the filename. This conflicts with old mirrored files
and the hash that we previously used.
To avoid conflict, use a renamed tarball from mirror2.openwrt.org
containing the new upstream changes
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Commit f5c741b5e0 updated procd to a more recent version, but did not
change the hash of the tar. Update it to the one matching the file on
the download servers.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The file to patch doesn't exists. Due to the fact that a src directory
exists, the patch was never applied.
With 28502a9 the behaviour was changed and revealed the issue.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This more of a demo for the previous commit that comes with
this one, where I added support for copying source from 'src' to
the build dir(s).
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
OpenWrt uses ancient u-boot thats not reproducible.
There are multiple upstream changes that introduce
reproducible builds like:
859e92b775fd8ebcfacc591eaf621b677c95b6f7
(not used here - the CMD_DATE/TIMESTAMP functionality
seems to be disabled by config)
70d39f57146a6cb94736db39c770c3d95e07bedb
f3f431a712729a1af94d01bd1bfde17a252ff02c
2d9efa1227262249d381ed5d9d341cbdba76e62d
Instead of changing the Makefile too much
this changeset just tries to use the
changes in Makefile from current upstream git f5fd45f
*Should* fix issue reported by reproducible lede page:
https://tests.reproducible-builds.org/lede/lede.html
Compile tested only
(verified w. hexdump & md5sum)
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Tested with VDSL on TP-Link WD8970, I see full 1500-byte PPP data
frames, which end up being 1526 byte Ethernet frames (including
Ethernet+VLAN headers) on the wire.
Fixes: FS#210
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Switch to xz tarball, there's no point pulling two different tarballs of the same source code (tools/libtool uses xz).
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
luci using ustream-mbedtls is extremely slow vs ustream-polarssl.
polarssl alias mbedtls v1 is configured to use NIST prime speed
optimisation, so no longer disable the default optimisation for
mbedtls v2.
Compile & run tested: Archer C7v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
[Jo-Philipp Wich: refresh patch to use common format]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Adds per-host leasetime support
Various bugfixes :
-Prioritize ifname resolving via ubus
-Free interface if ifindex cannot be resolved
-...
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [update mirror sha256]
This fixes the following error when mounting a ext4 filesystem
----
[ 166.240000] EXT4-fs (sda1): Cannot load crc32c driver.
----
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Commit 8f24ee6382 ("uqmi: Add proper IPv6 support") changed the code
to fetch the IPv4 address via QMI by default instead of using DHCP to
make it consistent with the IPv6 codepath.
This breaks on at least some Sierra Wireless cards, where data exchanges
fail to work until the host has fetched a DHCP lease.
Leave v6 as it is, but always use DHCP for v4.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
nf_tproxy_core was removed during 3.12 development with kernel commit
fd158d79d33d3c8b693e3e2d8c0e3068d529c2dc. The code was moved
to xt_TPROXY.c.
Fixes FS#212
Signed-off-by: Mathias Kresin <dev@kresin.me>
Adds the latest patches from Jes Sorensen for rtl8xxxu, which improve
rtl8732bu, rtl8192eu and rtl8188eu support.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* Change git packages to xz
* Update mirror checksums in packages where they are used
* Change a few source tarballs to xz if available upstream
* Remove unused lines in packages we're touching, requested by jow- and blogic
* We're relying more on xz-utils so add official mirror as primary source, master site as secondary.
* Add SHA256 checksums to multiple git tarball packages
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Quote resolveip hostname argument to avoid bad shell injections.
While at it fix pattern match logic in case multiple IPv6 addresses
are returned for a hostname as they're seperated by newline by
resolveip and not a white space
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Adds u-boot for the at91 platform and a couple of boards.
The build honours COPTS to benefit from fortify source et al.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Now that the uhttpd init script can generate certificates using openssl as
well, update the section name and related comment to be more generic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Before a configuration is generated, an empty file is created to store
it in. (required by UCI)
If something happens during config generation
(power cut, interruption, ..) an empty file exists and it is never
regenerated again, causing some daemons to fail starting
(NTPD, logread, ..)
Fix this by also generating new configs if a critical file
is empty.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The kmod-sound-hda-core module attempts to package snd-hda-core.ko which
does not exist in Linux 3.18, therfore only use it for kernels >= 4.1
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Support the usage of the OpenSSL command-line tool for generating
the SSL certificate for uhttpd. Traditionally 'px5g' based on
PolarSSL (or mbedTLS in LEDE), has been used for the creation.
uhttpd init script is enhanced by adding detection of an installed
openssl command-line binary (provided by 'openssl-util' package),
and if found, the tool is used for certificate generation.
Note: After this patch the script prefers to use the OpenSSL tool
if both it and px5g are installed.
This enables creating a truly OpenSSL-only version of LuCI
without dependency to PolarSSL/mbedTLS based px5g.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Prior to kernel 4.4, the hda-intel module depends on the hda-controller
utility submodule so bundle it for the older kernel versions.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Alberto Bursi
Paul Wassi
John Crispin
Jo-Philipp Wich
Imre Kaloz
Rafał Miłecki
Hannu Nyman
Felix Fietkau
Ben Greear
Pierre Lebleu
Alberto Bursi
Stijn Tintel
Hauke Mehrtens
Mathias Kresin
Alexandru Ardelean
Jan-Tarek Butt
Dirk Neukirchen
David Woodhouse
Daniel Engberg
Kevin Darbyshire-Bryant
diizzyy
Hans Dedecker
daniel
Álvaro Fernández Rojas
Hans Dedecker
Ben Whitten
Koen Vandeputte