Commit Graph

50 Commits (79741dc379178977a68672f8180f7d07796aae07)

Author SHA1 Message Date
Martin Blumenstingl 79741dc379 lantiq: Register the device tree node with the PCIe controller
This allows specifying PCI devices as children of the PCIe controller
node to pass configuration data to them.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2016-11-26 22:39:26 +01:00
Ben Mulvihill 6f60926bab lantiq: dwc2 parameters for danube
Parameters for dwc2 on lantiq.

A separate dwc2_core_params structure is defined for danube because danube
fifo sizes are large enough to be autodetected. This is not the case on
arx and vrx.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
2016-11-21 11:04:12 +01:00
Ben Mulvihill c82d5b30e1 lantiq: initialise dwc2 on danube
Initialise dwc2 usb driver on danube boards as well as ar9 and vr9.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
2016-11-21 11:03:59 +01:00
Stijn Tintel 8e47655d4e kernel: update kernel 4.4 to version 4.4.32
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked broken.
Runtime-tested on ar71xx, octeon.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2016-11-16 17:31:29 +01:00
Eddi De Pieri 07bc0d6089 lantiq: fix pci issue if mem kernel parameter is used
As specified by e0229a16b0 if the VR9
based router provides FXS ports and they should enabled then the
following must added to the kernel command line:

  mem=[TOTALMEMSIZE-2M] vpe1_load_addr=ADDRESS vpe1_mem=2M

By adding mem= parameter a pci device stop working correctly. The
pci-lantiq.c module use get_num_physpages() to compute dynamically the
memory amount of the board.

The mem= make the module to compute in the wrong way the BAR11MASK, so
in this situation the mask is misaligned with the dma area that the
hardware expects.

This patch is a port of what legacy ifxmips_pci.c does.

Signed-off-by: Eddi De Pieri <eddi@depieri.net>
2016-11-12 21:04:15 +01:00
Mathias Kresin 21d8de78dc lantiq: drop ralink eeprom handling function
The eeprom handling function from the rt2x00 driver is used and this
code is obsolete.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-09 20:02:18 +01:00
Stijn Segers 2f2ea7b44c kernel: update kernel 4.4 to version 4.4.30
This patch bumps the 4.4 kernel from .28 to .30 and refreshes the patches.
Compile-tested on ar71xx, x86/64, ramips/mt7621, brcm47xx and kirkwood.

Run-tested on ar71xx & ramips/mt7621, brcm47xx and kirkwood (last two confirmed
by P. Wassi).

Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2016-11-02 10:25:44 +01:00
Stefan Koch 4552bf158c lantiq: vpe softdog
(required not-distributable firmware blob - dump it by yourself from original firmware)

Signed-off-by: Eddi De Pieri <eddi@depieri.net>

(cherry picked from commit eb0ce57270d0b5b81b224b9336cf54707497eede)

Modified after cherry-pick:
obj in Makefile

Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
2016-10-31 16:51:33 +01:00
Stefan Koch e0229a16b0 lantiq: added support for VPE1
Created minimal patchset based on BB rev 43158 by Eddi De Pieri
14.07/openwrt.git 79472c025449efae9310defad0d3a73cff14d756

If the VR9 based router provides FXS ports and they shoud enabled then
the following must added to the kernel command line:
mem=[TOTALMEMSIZE-2M] vpe1_load_addr=ADDRESS vpe1_mem=2M maxvpes=1
maxtcs=1

To use FXS 2M of RAM are needed for the VPE firmware. The size is set
by vpe1_mem.
The available RAM must be reduced by this size using the mem argument.
A correct load address (example 0x83e00000) for the firmware must be given,
too.

Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
2016-10-31 16:51:33 +01:00
Mathias Kresin 23e3314cad lantiq: fix thermal sensors driver
Read the temperature including the decimale place from the CGU_GPHY1_CR
register.

Decrement the temperature read from the register by 38.0 degree celsius.
The temperature range of the sensor is -38.0 to +154 °C and the register
value 0 is equal to -38.0 °C. This fixes the report of unrealistic
temperatures as seen on all tested boards.

Give the SoC a few milliseconds to get the first temperature value. On
some rare occasions there is no temperature value in the register when
read the first time after activation. This leads to a reported
temperature of -38.0 °C on boot.

Only version 1.2 of the vr9 SoC has a temperature sensor. Add a check
to make sure the driver doesn't load on v1.1 vr9 SoCs.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-19 19:55:06 +02:00
Hauke Mehrtens 8370b9eede ntiq: make i2c-lantiqi driver compile again
It missed some changes needed for kernel 4.4. This is only used by the
Falcon SoC and not for the xRX SoCs.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-10-03 00:13:11 +02:00
Álvaro Fernández Rojas 7d559169c5 kernel: update to v4.4.23
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on brcm2708/bcm2710 only.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-09-30 20:08:21 +02:00
Álvaro Fernández Rojas d14c28fc80 kernel: update kernel 4.4 to version 4.4.20
Refresh patches for all targets that support kernel 4.4.
Compile-tested on brcm2708 only.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-09-15 08:10:55 +02:00
Daniel Gimpelevich 993ad29359 kernel: Backport pending appended DTB handling patches
Backport patches from upstream Linux kernel which are making the
kernel stores the appended dtb not in the same resisters as defined in
the UHI specification, use a separate variable on MIPS.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[some modifications]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-09-12 22:36:55 +02:00
Mathias Kresin 6fdc527793 lantiq: fix ath5k EEPROM loading
With 12fe4b5798 I switched the ath5k
eeprom extraction to an alternate code path. Unfortunately this code
seams to be broken since ages and broke the ath5k EEPROM extraction.

Reported-by: Mohammed Berdai <mohammed.berdai@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: John Crispin <john@phrozen.org>
2016-08-24 19:30:52 +02:00
Martin Schiller 528b769d42 lantiq/xrx200-net: Add support for eth0 as WAN interface
Use priv->wan instead of priv->id as indicator if packets should go to the
Ethernet WAN group (DPID=1) or not (DPID=0). This way, it's independant of
interface names or indexes.

Signed-off-by: Martin Schiller <mschiller@tdt.de>
2016-08-15 21:52:04 +02:00
Martin Schiller 8f02f7c7f8 lantiq/xrx200-net: fix "tx ring full" error by introducing second DMA TX channel
With an own DMA TX channel for each network device (eth0 + eth1) there
won't be any "tx ring full" errors any more.

This patch also move the spinlocks to the channel level instead of locking
the whole xrx200_hw structure.

Signed-off-by: Martin Schiller <mschiller@tdt.de>
2016-08-15 15:32:36 +02:00
Felix Fietkau eae422eb94 lantiq: fix some ethernet driver SMP issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-08-11 10:45:33 +02:00
Mathias Kresin 47d3909415 lantiq: drop duplicate and now unused "lantiq, eth-mac" binding
The device tree binding and the associated code duplicates functionality
already patched into the etop driver. The compatible string isn't used
any more. Therefore the whole code can be dropped.

The "mac-increment" property allowed to increment a mac address received
via kernel cmdline. This functionality isn't used by any device and
should be added as etop driver device tree property if required again.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-08-10 02:04:31 +02:00
Mathias Kresin a7cce111db lantiq: drop orphaned eeprom-handling code branches
All device tree nodes are using the named properties now and the code
path handling the reg property isn't required any more.

The code related to the ath,eep-flash property has been reformatted to
be better readable.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-08-10 02:04:31 +02:00
Felix Fietkau 1b9dbb8532 Revert "kernel: remove long obsolete gpio spi controller driver patch"
This reverts commit 9e62a7668c.
2016-08-04 23:10:15 +02:00
Felix Fietkau 9e62a7668c kernel: remove long obsolete gpio spi controller driver patch
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-08-04 20:53:02 +02:00
Florian Eckert 828e25e325 lantiq: add cpu temperatur sensor driver for xrx200
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
2016-08-03 15:30:13 +02:00
Hauke Mehrtens bf32177a1d kernel: remove full cache flush in fuse_copy_do() for MIPS
This patch was introduced in commit r16412 for the brcm47xx target only
and then moved to generic in commit r32395. It was initially added
because of ticket #5186 and should fix some problems with fuse file
systems and MIPS caches. The commit comment in r32395 says that this a
generic problem in MIPS CPUs, but does not name any specifics about
that. There was a fix added to kernel 2.6.21 in commit commit
7575a49f20 "[MIPS] Implement flush_anon_page()." that should fix this
problem, but that was already available before both commits were done
to OpenWrt.

I just tested fuse with ntfs.3g without this patch on a BCM4704
(BMIPS3300 V0.6) SoC and haven't seen any problems. Someone reported
that removing this patch improves some fuse operations by 5 times on
some modern MIPS cores.
My test was only a simple "dd if=/dev/zero of=/mnt/zero bs=5000" to an
USB stick.

This patch removes the patch to OpenWrt, because I assume that it is
not needed any more and Felix, the orginal author, also thinks so.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-06-26 18:22:23 +02:00
Hauke Mehrtens 84d489f64f kernel: update to version 4.4.14
Changelog: https://cdn.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.4.14

Some manual changes to target/linux/generic/patches-4.4/610-
netfilter_match_bypass_default_checks.patch were needed.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-06-26 18:20:37 +02:00
Hauke Mehrtens ecdfbeae85 lantiq: remove patch adding support for building without reset controller
The lantiq kernel arch code selects CONFIG_RESET_CONTROLLER always, so
it is always selected when the lantiq target is build. we do not need
support for unselected CONFIG_RESET_CONTROLLER option.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-06-21 21:58:59 +02:00
Felix Fietkau 3a75777e86 lantiq: refresh patches
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-15 14:36:47 +02:00
John Crispin 9233db23f3 lantiq: the io space was still not big enough for UHCI
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-14 08:34:05 +02:00
John Crispin d5666b98fa lantiq: fix fritz7320 wifi support
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-14 06:43:02 +02:00
John Crispin 98d00c35e3 lantiq: fix io_space_limit
this broke uhci pci support on some arv units

Signed-off-by: John Crispin <john@phrozen.org>
2016-06-14 06:43:02 +02:00
John Crispin 2ae06f3013 lantiq: gpio-export fails to build if GPIO_SYSFS is not enabled
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-13 22:51:43 +02:00
John Crispin d61af50cf3 lantiq: fix a regression in the eiu irq loading code
this worked in 3.18 but broke at some point. the old code that loaded a
irq table was incorrewct anyhow as it mapped the irqs int he domain which
should really be done when the driver using them loads them and not the
irq driver itself.

Signed-off-by: John Crispin <john@phrozen.org>
2016-06-13 22:51:41 +02:00
Felix Fietkau c536da365b lantiq: add VLAN handling fixes to xrx200 ethernet driver
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-13 17:58:07 +02:00
Felix Fietkau 172eebbd28 lantiq: fold 0400-xrx200-net-multi-phy.patch into 0025-NET-MIPS-lantiq-adds-xrx200-net.patch
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-13 17:58:07 +02:00
Felix Fietkau 1da87516e5 lantiq: change xrx200 ethernet driver WRED signal to global to fix spurious packet loss issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-12 14:53:18 +02:00
Felix Fietkau 2cf67832ec lantiq: remove dummy ltq_machine_power_off to fix gpio-poweroff drivers
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-11 09:49:13 +02:00
Daniel Gimpelevich 8b321d45be lantiq: Fix macaddr-setting code on DGN3500 and possibly other devices
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
2016-05-27 16:08:47 +02:00
Mathias Kresin 21bdd79b33 lantiq: disable phy led complex (test) functions by default
They can be added using the phy led device tree bindings if required.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-23 11:03:23 +02:00
Álvaro Fernández Rojas b062266ad6 kernel: update kernel 4.4 to version 4.4.9
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-05-10 10:43:17 +02:00
blogic 44cace4dab lantiq: add device tree binding for the phy clock source
Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 49283
2016-05-10 10:43:12 +02:00
blogic d7438ce315 lantiq: handle the dual-firmware layout of brnboot
brnboot based devices can have two Image partitions. When flashing
images via the brnboot recovery web interface, the Image partitions are
written alternating.

The current active Image partition is stored in the first byte of the
Primary_Setting partition by using 0x00 for Code_Image_0 and 0x01 for
Code_Image_1.

By using the information about the active "Code Image", it is possible
to ensure that the rootfs belongs to the current booted Image/Kernel.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 49281
2016-05-10 10:43:12 +02:00
blogic b529387d8c lantiq: use the same functionality for all ethernet phys led
The VGV7510KW22 has the leds for LAN1-3 connected to pin1 of the phys
and the led for LAN4 connect to pin0 of the phy. This results with the
current configuration in a fast flashing LAN4 led as soon as a network
cable is connected. Something similar was reported on the forum[1] for
the VGV7519 as well.

Since it isn't predicable to which pin a (single) phy led is connected,
use the (default) pin1 functionality

    Constant On: 10/100/1000MBit
    Blink Fast: None
    Blink Slow: None
    Pulse: TX/RX

for all ethernet phy leds.

After checking pictures of all vr9 boards, it looks like only the VG3503J
has more than one led connected per phy. Using the phy led device tree
bindings to assign the functionality to the "additional" leds, the
VG3503J phy leds should behave as before.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

[1] https://forum.openwrt.org/viewtopic.php?pid=321523

SVN-Revision: 49270
2016-05-10 10:43:12 +02:00
blogic 6249269322 lantiq: fix minor typos in 11G/22F phy driver
Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 49269
2016-05-10 10:43:12 +02:00
Álvaro Fernández Rojas 3faf65e928 kernel: update kernel 4.4 to version 4.4.8
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-04-24 11:32:17 +02:00
Hauke Mehrtens f0b3964f1b kernel: update kernel 4.4 to version 4.4.7
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 49176
2016-04-16 21:05:48 +00:00
John Crispin d6d0597cdf lantiq: use upstream mechanism to append device tree file
Instead of using our patch-dtb program just place the device tree
behind the kernel binary and then let the in kernel mechanism fetch it.
This also adds support for having the device tree file in the boot
loader.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 49050
2016-03-20 14:41:54 +00:00
Hauke Mehrtens cb04b8d582 kernel: update kernel 4.4 to version 4.4.3
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 48783
2016-02-25 21:54:39 +00:00
John Crispin c3fc71527d lantiq: fix wrong parameter order in xway_nand driver
Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 48656
2016-02-08 08:25:15 +00:00
Felix Fietkau d4fe52c16d lantiq: fix PHY state handling issue
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48546
2016-01-29 00:42:38 +00:00
Felix Fietkau f577cb25c0 lantiq: Add support for linux 4.4
The following patches were dropped because they are already applied
upstream:
- 0038-MIPS-lantiq-fpi-on-ar9.patch
- 0039-MIPS-lantiq-initialize-usb-on-boot.patch
- 0042-USB-DWC2-big-endian-support.patch
- 0043-gpio-stp-xway-fix-phy-mask.patch

All other patches were simply refreshed, except the following:
- 0001-MIPS-lantiq-add-pcie-driver.patch
  Changes to arch/mips/lantiq/xway/sysctrl.c (these changes disabled
  some PMU gates for the vrx200 / VR9 SoCs) were removed since the
  upstream kernel disables unused PMU gates automatically (since
  95135bfa7ead1becc2879230f72583dde2b71a0c
  "MIPS: Lantiq: Deactivate most of the devices by default").
- 0025-NET-MIPS-lantiq-adds-xrx200-net.patch
  Since OpenWrt commit 55ba20afcc2fe785146316e5be2c2473cb329885 drivers
  should use of_get_mac_address(). of_get_mac_address_mtd is not
  available for drivers anymore since it's called automatically within
  of_get_mac_address().
- 0028-NET-lantiq-various-etop-fixes.patch
  Same changes as in 0025-NET-MIPS-lantiq-adds-xrx200-net.patch

While refreshing the kernel configuration SPI support had to be moved to
config-4.4 because otherwise M25P80 was disabled.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 48307
2016-01-18 11:40:19 +00:00