When running "make menuconfig" with symlinked .config (e.g. to
env/.config) it renames symlink to .config.old, creates new .config file
and writes updated configuration here.
This breaks the desired workflow when changes in the configuration could
be checked using "scripts/env diff" and commited with
"scripts/env save". Since the env/.config file is not updated.
Fix this issue by exporting KCONFIG_OVERWRITECONFIG=1, which forces
mconf to overwrite the .config content, instead of renaming it and
creating a new file. This variable is set only if .config is a symlink,
otherwise the variable is not exported and the old behaviour is
preserved.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
The WN3000RPv3 is a repeater with a single ethernet port. Setting up the
switch, even to disable it, is unnecessary and possibly confusing.
Configure LAN as eth0 instead.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Add support for the Observa Telecom VH4032N router.
This is another BCM6368 router, 128 MB RAM, 32MB flash and 3 USB
host ports.
The wifi chip is an onboard Broadcom BCM43222.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
[jonas.gorski: use gpio-hog instead of abusing ephy-reset]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The Sanlinking Technologies D240
(http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same
device as the ZBT WE826, so adding support for it in LEDE is straight forward.
The differences is that the D240 has two mini-PCIe slots (instead of one), blue
LEDs and supports PoE.
Specification:
* CPU: MT7620A
* 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps.
* 16 MB Flash.
* 128 MB RAM.
* 1x USB 2.0 port.
* 2x mini-PCIe slots.
* 2x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.
Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to
test the SD card reader.
The device comes pre-installed with an older version of OpenWRT, including Luci.
In order to install LEDE, you need to follow the existing procedure for updating
OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to keep
existing settings. The default router address is 192.168.10.1 and
username/password admin/root (at least on my devices).
If you brick the device, the procedure for recovery is the same as for the
WE826. Please see the wiki page for that device for instructions.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
The comptible string is neither added by any LEDE patch nor exists in
in the kernel. Drop the sound node which was obviously added
accidentally with 9195d8da ("ramips: DTS rework").
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use only the jedec,spi-nor compatible string. Everything else either
never worked or is only support to keep compatibility.
Remove the linux,modalias property. It is obsolete since kernel 4.4.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fixes build issues with some toolchains that don't add lcrypt in the default
search paths:
CMakeFiles/rpcd.dir/session.c.o: In function `rpc_login_test_password':
build_dir/target-mipsel-linux-gnu/rpcd-2016-12-03-0577cfc1/session.c:823: undefined reference to `crypt'
collect2: error: ld returned 1 exit status
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
ramips/rt288x WLI-TX4-AG300N was missing support for its 100Mbit switch which
should be included by default.
Signed-off-by: Yo Abe <abe.geel@gmail.com>
[Jo-Philipp Wich: picked from OpenWrt PR#359, rewrap commit msg, fix Sob]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
On some EX2700 devices, the MAC address from the eeprom data differs
from the actual MAC address. Fix that, and cleanup the DTS file
while we're at it.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
This patch adds support for the Netgear WN3000RPv3
http://www.netgear.com/support/product/wn3000rpv3.aspx
Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Serial: JP1 header, 57600-8N1
- Stock firmware based on OpenWRT Kamikaze
Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This is why the same fakeroot image is used for the WN3000
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
For the miwifi-mini, the offset of ethernet mac should be 0x28
which you can easyily dump from 'Factory' partition.
Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
Implement a new flag "-f" for the feeds update command which causes the
script to fall back to a more agressive git update strategy in case there
are locally modified files in the feeds directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The WN3000RPv3 is a repeater with a single ethernet port. Setting up the
switch, even to disable it, is unnecessary and possibly confusing.
Configure LAN as eth0 instead.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Due to an oversight during patch conflict resolution, the PKG_VERSION got
accidentially bumped instead of the PKG_RELEASE field.
Revert the bad version change as there exists no upstream 1.25.2 version.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
When invoking "nslookup_lede" with a domain argument and without explicit
query type, issue both A and AAAA queries and display the resulting IP
addresses in a numbered list style, similar to how the old BusyBox nslookup
used to output the records.
This is required for compatibility with certain scripts.
Ref: https://forum.lede-project.org/t/nslookup-ipv6-in-lede-17-01-1
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The ":*" optstring syntax was only recently introduced with BusyBox v1.26,
older versions need a corresponding hint in the "opt_complementary" variable
to denote flag values that should be stored as llist entries.
Add the required opt_complementary entry to fix random SIGBUS, SIGILL or
SIGSEGV related crashes on BusyBox 1.25.x when attempting to use the "-q"
flag of the "nslookup_lede" applet.
Ref: https://forum.lede-project.org/t/nslookup-ipv6-in-lede-17-01-1
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fixes FS#684 with commit 21a4bd0
Changes since current version. All changes except the ones prefixed
with asterisks are for bugfixes. Module aliases awareness is expected
by the kernel to be a basic facility and is required for properly
initializing wireguard.
16f7e16 syslog: remove unnecessary sizeof struct between messages
21a4bd0 kmodloader: modprobe: return 0 for loaded modules
3dc78a4 kmodloader: don't store aliases info in struct module
c553354 cmake: fix typo
8973576 kmodloader: fix not being able to find some modules
fce9382 cmake: Check for getrandom system call
ac2d43e kmodloader: support '-q' quiet option
*f8d3d16 ubox: Add an option for more accurate timestamps in log
14839f0 kmodloader: make insert_module() idempotent
*6e3c6dc kmodloader: add module alias awareness
9371411 kmodloader: fix out-of-bound access when parsing .modinfo
a62c946 kmodloader: modprobe: skip possible command line arguments
*46a4b5f kmodloader: log to kmsg when loading directories of modules
eacc426 kmodloader: remove redundant glob wildcard char
8488bb5 ubox: Initialize conditionally uninitialized variabled
db070f1 ubox: Fix some memory leaks
acc48b5 kmodloader: Fix typo in error message
Size comparison on x86_64 host
function old new delta
main 2190 2344 +154
scan_module_folder 665 793 +128
alloc_module_node - 113 +113
.rodata 946 1036 +90
alloc_module 202 245 +43
free_modules 77 119 +42
load_modprobe 209 237 +28
scan_loaded_modules 241 265 +24
avl_modcmp 45 67 +22
insert_module 204 224 +20
find_module 13 30 +17
static.optind@@GLIBC_2 - 4 +4
static.load_moddeps 118 117 -1
scan_module_folders 55 54 -1
------------------------------------------------------------------------------
(add/remove: 2/0 grow/shrink: 10/2 up/down: 685/-2) Total: 683 bytes
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
We need to ensure there is enough headroom to push extra header,
but we also need to check if we are allowed to change headers.
skb_cow_head() is the proper helper to deal with this.
Fixes Ethernet<->WiFi bridge for Raspberry Pi and probably other devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Fix a '==' that should be a '=' in a test condition. Busybox fortunately
doesn't care.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The current way of creating a STAMP_CONFIGURED filename for OpenSSL can
lead to an extremely long filename that makes touch unable to create it,
and fail the build.
Use mkhash to produce a hash against OPENSSL_OPTIONS which creates a
shortert stamp file,
Fixes#572
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Protect any IPv6 related with appropriate guards to fix compilation with
disabled IPv6 support in Busybox.
Fixes#728.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Since the LEDE nslookup applet is already specific to LEDE, move the
libresolv detection into the busybox Makefile that LEDE uses.
This fixes builds with external toolchains that don't automatically
search for headers and/or libraries without being told so.
Fixes: de5b8e5d2f ("busybox: add musl compatible nslookup replacement")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This fixes GIC interrupts (required before switching to 4.9), adds few
new entires & introduces DTS for Archer C5.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This router has the same hardware as TP-LINK TL-WR841N/ND v11 (same FCC
ID, same TFTP image name...).
If the stock firmware web interface doesn't accept LEDE factory image,
it can be flashed via the U-Boot TFTP recovery mode, by long-pressing
the reset button after power on.
The TFTP image name is wr841nv11_tp_recovery.bin (yes, v11, not v12).
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
Add an alternative nslookup applet implementation which is compatible with
musl libc wrt. name server selection and which supports a number of additional
features such as query type selection.
Fixes#155, #217
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fix the PCIe 5GHz wireless by using the on flash eeprom/caldata.
Disable the 2.4GHz band as this band has no antennas attached but is
enabled in the eeprom/caldata.
Fixes: FS#691
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fix the PCIe 5GHz wireless by using the ralink mtd-eeprom property as
this board have a RT5592 and uses the rt2x00 driver. The mediathek
device tree bindings do not work here.
Fixes: FS#691
Fixes: d8dd207ea6 ("ramips: use the ralink,mtd-eeprom device tree property")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Hans Dedecker
Sergey Ryazanov
Thibaut VARENE
Daniel Gonzalez Cabanelas
Koen Vandeputte
Kristian Evensen
Piotr Dymacz
Mathias Kresin
Felix Fietkau
Florian Fainelli
Vitaly Chekryzhev
Yo Abe
Joseph C. Lehner
BangLang Huang
Jo-Philipp Wich
Furong Xu
Giuseppe Lippolis
Yousong Zhou
Álvaro Fernández Rojas
Matthias Schiffer
Rafał Miłecki
Vittorio Gambaletta
Daniel Engberg