Commit Graph

13429 Commits (72822d019204c66607626c75f5d78861865750fa)

Author SHA1 Message Date
Felix Fietkau 978830466a kernel: fix the mips module relocation patch for 3.19+
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 44590
2015-03-02 04:42:17 +00:00
Rafał Miłecki fac0ad0827 adm5120: switch kernel to 3.18
Tested by Jonas on WP54g, thank you!

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 44588
2015-03-01 16:24:15 +00:00
Rafał Miłecki c9035566d5 adm5120: enable low_mem
Most devices have only 16 MiB of RAM, this will allow them to boot
without OOM.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 44587
2015-03-01 16:24:11 +00:00
Lars-Peter Clausen 464e7a7f10 xburst: Remove n516, n526 and id800wt subtargets
The driver code for supporting these subtargets was already removed a while ago,
so
the current images wont actually boot.

It is also quite unlikely that there are any users of them at this point, so
remove them.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>

SVN-Revision: 44586
2015-03-01 15:56:43 +00:00
Jonas Gorski 3069934e37 brcm47xx, brcm63xx: disable CONFIG_MIPS_O32_FP64_SUPPORT
The flag is experimental and requires toolchain support, which we don't
provide. Also neither target has an FPU so it becomes meaningless
without the FPU emulator enabled.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 44584
2015-03-01 11:37:18 +00:00
Jonas Gorski 3139140339 kernel: move CONFIG_MIPS_O32_FP64_SUPPORT to generic configs
Most MIPS targets have it disabled, so move the symbol to the generic
configs to keep target configs small.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 44583
2015-03-01 11:37:15 +00:00
Jonas Gorski 18322746de brcm63xx: prefer gpio-button-hotplug over button-hotplug
Saves us pulling in the input system, shaving off a few kb from image
sizes.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 44582
2015-03-01 11:37:06 +00:00
Rafał Miłecki 999c59482f adm5120: use subtarget configs for all kernels
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 44581
2015-03-01 00:01:33 +00:00
Rafał Miłecki 780d6939b2 adm5120: add 3.18 support
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 44580
2015-02-28 23:39:14 +00:00
Rafał Miłecki 0e7e585752 ep93xx: add 3.18 support
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 44579
2015-02-28 22:46:42 +00:00
Rafał Miłecki 578b5ed2b0 mpc52xx: add 3.18 config
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 44578
2015-02-28 20:53:55 +00:00
Jonas Gorski dd618e499f brcm63xx: fix DTS LEDs and buttons
- A4001N/A4001N1: fix swapped green and red LEDs
- CVG834G: add missing LED
- RTA1320: reorder LEDs by GPIO#
- V2500V: add missing LEDs and buttons
- WAP-5813n: fix WPS button (GPIO 35)

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 44577
2015-02-28 19:59:50 +00:00
Jonas Gorski 40e6eae61f brcm63xx: fix ethernet breakage in 3.18
Linux commit d75b1ade567ffab ("net: less interrupt masking in NAPI")
chose the samantics of the napi poll return value, which caused napi to
not resume interrups/polling anymore.

Fix the return value to restore expected behaviour.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 44576
2015-02-28 19:59:46 +00:00
Jonas Gorski 6df9324642 brcm63xx: fix BCM63268 interrupt register locations for legacy probe
Legacy probe passed the IRQSTAT registers instead of the IRQMASK
registers causing all register accesses to be offset by 16 bytes.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 44575
2015-02-28 19:59:34 +00:00
Jonas Gorski c2a89871c2 brcm63xx: fix gpio register usage
The driver expected data then dir, but both dts and legacy code passed
dir then data. Fix this by making the driver expect the registers in
ascending order, i.e. dir then data.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 44574
2015-02-28 19:59:26 +00:00
Rafał Miłecki 15fb17791a mpc83xx: start work on 3.18 support
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 44573
2015-02-28 18:15:59 +00:00
Rafał Miłecki 151b6b3432 omap: complete 3.18 support
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 44572
2015-02-28 14:56:53 +00:00
Rafał Miłecki dccefe7b53 omap: start working on 3.18 support
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 44571
2015-02-28 13:54:51 +00:00
Jonas Gorski b694c45d33 brcm63xx: backport and enable DT spi-gpio no CS support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 44570
2015-02-27 23:48:48 +00:00
Jonas Gorski b6ad4b7332 brcm63xx: fix image generation and broken patch
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 44569
2015-02-27 23:48:32 +00:00
Jonas Gorski d75cd5be37 b53: fix mmap register read/writes > 32 bit
For bcm63xx integrated switches, broadcom changed the data endianess
to match the system endianess. But this only applies to within one word,
which causes 48/64 bit values to be still split into their "litte endian"
groups.

E.g. 48 bit values (with 5 being the most significant byte) aligned

0x00 ..01  or   0123
0x04 2345       45..

will become

0x00 ..10 resp. 3210
0x04 5432       54..

Likewise for 64 bit values.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 44568
2015-02-27 17:40:17 +00:00
Jonas Gorski 8ff23c60e2 brcm63xx: remove gpio base workaround
Now that all gpio users without named gpios use DT, we do not need
to fix the gpio controller bases anymore.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 44567
2015-02-27 17:40:09 +00:00
Jonas Gorski b82cb155fc brcm63xx: move buttons and leds to dts files
Register buttons and leds through DT for all available dts,
and remove them from the board files.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: remove leds/buttons from board files
       fix wrong led polarities for dsl-274xb-c2, cpva642, p870hw
       comment out spi-gpio and associated leds]

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 44566
2015-02-27 17:40:04 +00:00
Jonas Gorski eea227c60d brcm63xx: probe gpio controllers through DT
Add a generic mmio gpio controller based driver and probe it
through device tree.

Use aliases for base calculation until we converted all users to
device tree or named gpios.

Convert bcm63xx_enet's ephy-reset gpio to use a named gpio.

While at it, remove the duplicate reset gpio defintion for livebox.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 44565
2015-02-27 17:39:49 +00:00
Jonas Gorski 1efb7398e1 brcm63xx: convert BTV2500V to dts
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 44564
2015-02-27 17:39:29 +00:00
Jonas Gorski 90c15beee6 brcm63xx: convert RTA1320 to dts
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 44563
2015-02-27 17:39:21 +00:00
Jonas Gorski 5a9b7c28c3 brcm63xx: convert RTA1025 to dts
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 44562
2015-02-27 17:39:13 +00:00
Jonas Gorski 9a65e1a570 brcm63xx: use dtb for cvg834g
Add a dtsi for bcm3368, add a dts and profile for cvg834g, and convert
it to use ImageDTB. Since HCS requires more arguments, enhance the max
arguments of the call.
The image name is intentionally left blank to prevent non-initramfs
images to be built, as they currently contain no rootfs and consequently
won't work.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 44561
2015-02-27 17:39:07 +00:00
Jonas Gorski 69b327247c brcm63xx: image: move image argument to front in *DTB calls
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 44560
2015-02-27 17:38:51 +00:00
Jonas Gorski f3c071b376 brcm63xx: add dts and profile for Livebox
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 44559
2015-02-27 17:38:46 +00:00
Jonas Gorski dd7625ef15 brcm63xx: allow lzma to use 32MB RAM
Most 16 MiB RAM devices don't even load elf kernels, so it's safe to
assume we have at least 32 MB RAM. This fixes tftp booting with the
default package set as this already produces an uncompressed
kernel > 8 MiB.

New limit is 8 MiB compressed / 24 MiB compressed.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 44558
2015-02-27 17:38:28 +00:00
Jonas Gorski 92eb27f56d package: mtd: move bcm963xx_tag definition into source code
Remove the need for the header file to be exported - we don't need most
of it anyway; all we care about are the offset of the rootfs length and
header crc fields.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 44557
2015-02-27 17:38:25 +00:00
Jonas Gorski bb54859543 brcm63xx: do not align squashfs rootfs start
We do not need to align the start of read only rootfs's to erase blocks.
This allows us to write the squashfs rootfs directly behind the kernel,
potentially freeing up one erase block.

We still need to align for jffs2, so add a flag for imagetag to
optionally align the rootfs start.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 44556
2015-02-27 17:38:14 +00:00
Jonas Gorski d4652e817a brcm63xx: drop call to prepare_generic_squashfs
We do not use the result, so no need to call it.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 44555
2015-02-27 17:38:09 +00:00
Felix Fietkau b64ca483ef kernel: fix 3.18+ if_bridge.h header conflict with musl
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 44553
2015-02-27 07:35:26 +00:00
Imre Kaloz f76a752c57 generic/4.0: refresh patches
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 44532
2015-02-24 18:53:14 +00:00
Imre Kaloz 11e93be20d generic/4.0: drop patches applied upstream
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 44531
2015-02-24 18:35:17 +00:00
Imre Kaloz c407264643 generic/4.0: drop 3.18 specifix dwc2 backport
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 44530
2015-02-24 18:30:16 +00:00
Imre Kaloz efea65bb99 generic/4.0: the ubi patches has been fixed in the 3.19 patchset already
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 44529
2015-02-24 18:27:49 +00:00
John Crispin e67f5ed2e6 ar71xx: refresh patches
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44528
2015-02-24 12:01:08 +00:00
John Crispin 1c5a2826e3 ar71xx: Add QCA953X version2 SoC support
http://patchwork.ozlabs.org/patch/435234/

Signed-off-by: 郭传鈜 <gch981213@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44527
2015-02-24 12:01:00 +00:00
John Crispin 9358a8a798 ar71xx: TL-WA7210n v2 support
This patch adds support for TP-Link TL-WA7210n[0]

[0] http://www.tplink.com/en/products/details/?model=TL-WA7210N

Signed-off-by: Hendrik Frenzel <hfrenzel@scunc.net>

SVN-Revision: 44526
2015-02-24 12:00:50 +00:00
John Crispin 7c24d8627f ipq806x: add ahci to default packages
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44525
2015-02-24 12:00:22 +00:00
John Crispin 458c37fb14 ipq806x: add default package selection
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44523
2015-02-24 12:00:09 +00:00
John Crispin de7100d818 ipq806x: initialize the network on AP148
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 44522
2015-02-24 12:00:04 +00:00
John Crispin 9b6adc2d3a ipq806x: enable GMAC support in DTS
This adds the GMAC entries in the ipq806x dtsi file as well as in the
ap148 specific dts file.

This also adds the MDIO change as well.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 44520
2015-02-24 11:59:51 +00:00
John Crispin 8eda29f12c ipq806x: enable ar8xxx switch family support
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 44519
2015-02-24 11:59:47 +00:00
John Crispin a45a5f7cf0 ipq806x: fix spi read issues observed with SMP enabled
This change is fixing the issues observed when booting from NOR flash
with SMP enabled.

Error logs below:
building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of
xref (0 dead, 0 orphan) found.
m25p80 spi32766.0: SPI transfer failed: -110
spi_master spi32766: failed to transfer one message from queue
jffs2: Write of 873 bytes at 0x019001e8 failed. returned 0, retlen 792

Patch is cherry-picked from here:
https://www.codeaurora.org/cgit/quic/qsdk/oss/kernel/linux-msm/commit/drivers/spi/spi-qup.c?h=coconut_20140924&id=4faba89e3ffbb1c5f6232651375b9b3212b50f02

More details in the patch file.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 44518
2015-02-24 11:59:41 +00:00
John Crispin 1175e83f50 mpc85xx: add 3.19 support
It took very little to make the TL-WDR4900 work under 3.19:
- config is the same as for 3.18
- only patch 210 had to be refreshed, the other patches are
  the same as for 3.18
- in /etc/config/wireless the path options need to be prefixed
  with "platform/" ('platform/ffe09000.pci/...')

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>

SVN-Revision: 44517
2015-02-24 11:59:35 +00:00
Rafał Miłecki e8acbb11a4 generic: fix 050-backport_netfilter_rtcache.patch
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 44514
2015-02-24 06:40:37 +00:00
Felix Fietkau 362bc849bc x86: remove spurious delete of /etc/config/network
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 44513
2015-02-24 06:07:40 +00:00
Rafał Miłecki 1c063070cf generic: early (incomplete!) 4.0 support
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 44511
2015-02-23 22:59:53 +00:00
Imre Kaloz e02478a22a mvebu: set default WRT1900AC switch config
This sets 'enable_vlan' and thus uses 802.1q
VLANs, but without tagging on either interface.

Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 44509
2015-02-23 10:35:29 +00:00
Imre Kaloz 0de48a0dd8 mvebu: set WRT1900AC WAN interface MAC address
Toggles the LA bit on the WAN interface.

Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 44508
2015-02-23 10:33:19 +00:00
John Crispin 6aab00fa44 ipq806x: delete config-3.14 file
ipq806x target has been upgraded to 3.14. There is no need to maintain
this file anymore.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 44505
2015-02-22 08:29:18 +00:00
John Crispin 565a6f2a27 ipq806x: fix "reboot" command
The watchdog driver already registers a restart notifier, we just have
to enable it in the config and in the DT to fix the "reboot" command.

This is done by integratin the following patch-set:
https://lkml.org/lkml/2015/2/20/610

I'm copy-pasting the description below:
qcom-wdt is currently assuming the presence of a dedicated node in DT
to gets its configuration. However, on msm architecture, the watchdog is
usually part of the timer block. So this patch-set is changing the driver
and slightly enhancing the timer DT bindings to provide the relevant clocks
and interrupts.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 44504
2015-02-22 08:29:14 +00:00
John Crispin 5072954cd0 ipq806x: enable watchdog kernel option
Some bootloaders seem to trigger the watchdog during the boot process,
therefore the lack of watchdog driver trigger a reboot a few seconds
after boot. So we'll enable it here to avoid it.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 44503
2015-02-22 08:29:07 +00:00
John Crispin 7938da42f5 kernel: Fix USB gadget modules for v3.18
Updated patch that fixes whitespace and supports kernel v3.3 too.

Signed-off-by: Owen Kirby <osk@exegin.com>

SVN-Revision: 44502
2015-02-22 08:29:01 +00:00
John Crispin 2f544d56d0 mpc85xx: add mpic timer clock frequency to avoid boot log warning
MPIC timers are enabled in the config, however a devicetree clock setting
is missing causing the following error:
/soc@ffe00000/timer@41100: cannot get timer frequency.
/soc@ffe00000/timer@42100: cannot get timer frequency.

This patch adds the missing clock and avoids the error.
It's a functional copy of this code
do_fixup_by_compat_u32(blob, "fsl,mpic",
        "clock-frequency", get_bus_freq(0), 1);
in arch/powerpc/cpu/mpc85xx/fdt.c in the u-boot code.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>

SVN-Revision: 44501
2015-02-22 08:28:48 +00:00
John Crispin 850b3169ed ramips: rt288x: add missing symbol
Defaulting to disabled, based on the value of
the (old?) CONFIG_RALINK_USBPHY

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 44500
2015-02-22 08:28:42 +00:00
John Crispin 0ba8217008 ramips: nexx wt3020: fix status led
For Nexx WT3020 board_name is wt3020, not nexx-wt3020

root@OpenWrt:~# . /lib/ramips.sh; echo $(ramips_board_name)
wt3020

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 44499
2015-02-22 08:28:35 +00:00
Rafał Miłecki a416029d4d bcm53xx: add one more NVRAM possible size (0x180000)
Size 0x160000 was added to support Buffalo WZR-600DHP2, however Netgear
devices (R6250, R8000) require 0x180000.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 44497
2015-02-20 07:07:53 +00:00
John Crispin e071f4fd1a mpc85xx: set v3.18 as default
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44496
2015-02-19 14:30:03 +00:00
John Crispin 52b2a2c398 ralink: bump to v3.18
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44495
2015-02-19 14:04:47 +00:00
John Crispin 64db436416 ramips: fix the mt7628 dts file
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44494
2015-02-19 14:04:41 +00:00
John Crispin 0227827f7b at91: Add dts for Exegin Q5x boards.
Signed-off-by: Owen Kirby <osk@exegin.com>

SVN-Revision: 44492
2015-02-19 09:07:06 +00:00
John Crispin 3cf87e67b2 at91: USB gadget subsystem cleanup and driver fix.
Signed-off-by: Owen Kirby <osk@exegin.com>

SVN-Revision: 44491
2015-02-19 09:06:56 +00:00
John Crispin 6fb59689c6 at91: Enable power and reset controller drivers.
Signed-off-by: Owen Kirby <osk@exegin.com>

SVN-Revision: 44490
2015-02-19 09:06:49 +00:00
John Crispin 4a6e468588 at91: bump to v3.18
Signed-off-by: Your Name <blogic@openwrt.org>

SVN-Revision: 44489
2015-02-18 13:35:46 +00:00
John Crispin 1a1d69da08 au1000: fix 3.18 and set it as default
Thanks to Bruno Randolf for testing and Manuel Lauss for providing a fix.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44487
2015-02-18 09:49:38 +00:00
Jo-Philipp Wich f9aa2ec7f6 ar71xx: fix 82_patch_ath10k
The firware md5sum check never worked due to missing dollar signs.

Also suppress
  `md5sum: can't open '/lib/firmware/ath10k/QCA988X/hw2.0/firmware-3.bin'`
error on any board not using ath10k.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 44486
2015-02-17 21:26:39 +00:00
John Crispin 7cfc88bac8 mpc85xx: add v3.18 support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44485
2015-02-17 20:28:36 +00:00
John Crispin a54f062bd4 ar71xx: make v3.18 default
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44482
2015-02-17 14:33:29 +00:00
John Crispin c2c2f64c66 kernel: re-enable the firmware loader
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44481
2015-02-17 14:33:13 +00:00
John Crispin 3618391514 ramips: Buffalo WZR-AGL300NH target support
I got work with this patch.
Ethernet switch (includes VLAN), WiFi connected via PCIe, LEDs, buttons.

In mtd partion map of DTS file, I renamed Linux firmware regions (kernel + root squashfs) to “firmware”because it allows kernel to split kernel and roots and rootfsdata.

signed-off-by: ngc@ff.iij4u.or.jp
——
——

SVN-Revision: 44470
2015-02-16 21:19:18 +00:00
John Crispin f440414c55 ramips: enables rt288x PCIe
To choose whether bulid or not RT288x PCIe bus driver, CONFIG_SOC_RT2880 is wrong.
Here is its fix, and enables PCIe bus driver for some targets which have 2nd WiFi chipset via PCIe bus.

signed-off-by: ngc@ff.iij4u.or.jp
————
————

SVN-Revision: 44469
2015-02-16 21:18:59 +00:00
John Crispin 5a8d78d710 oxnas: fix itb generation
- according to imx6 Makefile and u-Boot documentation is itb
  and probably should not be changed
- this fixes build error if CONFIG_TARGET_ROOTFS_INCLUDE_FIT is set
  (missing .itb file)
- use DTS_DIR (like in imx6 Makefile)

only compile tested

Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Acked-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 44468
2015-02-16 21:18:48 +00:00
Rafał Miłecki 08b45f73db bcm53xx: include kmod-brcmfmac in default profile
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 44467
2015-02-16 19:51:21 +00:00
Rafał Miłecki 44253d311f bcm53xx: sprom: extract for PCI host
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 44464
2015-02-16 16:13:23 +00:00
Rafał Miłecki 4c98253648 bcm53xx: sprom: prepare to support other hosttype-s
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 44463
2015-02-16 16:10:05 +00:00
Imre Kaloz 29130d39e3 mvebu: refresh 3.18 patches
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 44462
2015-02-16 12:48:05 +00:00
John Crispin 4e5c2b6f46 ar71xx: fix mv88e6063 compile for 3.14
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44459
2015-02-15 21:15:42 +00:00
John Crispin 1e5aa68071 ar71xx: fix a compile bug in 902-unaligned_access_hacks.patch
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44458
2015-02-15 21:15:21 +00:00
John Crispin 7e4b3de249 ar71xx: add v3.18 support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44456
2015-02-15 19:45:29 +00:00
Imre Kaloz 9b1c7a9de4 mvebu: fix WRT1900AC ubinized images
The current pxa3xx_nand driver doesn't support sub-page writing,
so the VID header offset must be specified explicitly.

Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 44455
2015-02-14 22:18:35 +00:00
John Crispin 428dd56a60 ralink: fix the config files
oops, accidently moved instead of copied them

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44454
2015-02-14 20:48:53 +00:00
John Crispin 503a1aaaf6 ar71xx: ZyXEL NBG6716 rfkill switch fix
ZyXEL NBG6716 "rfkill" is a switch, not a button.

Signed-off-by: Marcin Mikolajczak <gr4ffy at gmail.com>

SVN-Revision: 44453
2015-02-14 20:48:42 +00:00
John Crispin e07c4f2150 lantiq: disable buffered writes on Intel command set flash
Some Lantiq SoCs are not able to use buffered writes properly with
Intel command set flash due to the way NOR addresses on EBU are
manipulated. This patch disables buffered writes on those devices.
The only device affected at the moment is ARV4510PW, others use
AMD/Fujitsu command set.

Signed-off-by: Matti Laakso <malaakso@elisanet.fi>

SVN-Revision: 44451
2015-02-14 20:48:32 +00:00
John Crispin a15dd8ec78 lantiq: Fix flash for targets with NO_XIP
For targets with NO_XIP ltq_mtd->map[i].phys equals -1 and devm_ioremap fails.
Fix this by using pdev->resource[i].start instead.

Signed-off-by: Matti Laakso <malaakso@elisanet.fi>

SVN-Revision: 44450
2015-02-14 20:48:26 +00:00
John Crispin af3b4077bd brcm2708: add kmod-hwmon-bcm2835 support and more missing symbols
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 44449
2015-02-14 20:48:20 +00:00
John Crispin 9270474941 brcm2708: force uart as the default console for procd and remove nonexistent console
procd gets last console from cmdline, so swapping tty1 (framebuffer) and ttyAMA0 (uart) is enough to force procd output via uart

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 44448
2015-02-14 20:48:14 +00:00
John Crispin dc72499b53 brcm2708: add board detection and LED support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 44447
2015-02-14 20:48:08 +00:00
Nicolas Thill 40c0261f34 generic: ocf: irq compat stuff is not needed anymore
Signed-off-by: Nicolas Thill <nico@openwrt.org>

SVN-Revision: 44444
2015-02-14 13:53:44 +00:00
Imre Kaloz 4893c0c7f7 generic: upgrade to 3.18.7
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 44442
2015-02-14 10:45:12 +00:00
John Crispin 285348e086 ixp4xx: fix gpio_line_set() logic, fixes #18986
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44439
2015-02-13 10:54:01 +00:00
John Crispin 0d36998795 brcm2708: fix spidev
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 44434
2015-02-13 07:38:33 +00:00
John Crispin 9b74de00f7 brcm2708: refresh patches
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 44433
2015-02-13 07:38:27 +00:00
John Crispin 2dbcf5e91f brcm2708: add missing config symbols and fix kernel modules for Raspberry Pi 2 by removing local version
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 44432
2015-02-13 07:38:00 +00:00
John Crispin fae2ec33d1 brcm2708: add subtarget copyright and use better board names
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 44431
2015-02-13 07:37:55 +00:00
John Crispin c6224cf05d ar7: switch to v3.18
Thank you Dimitri for testing this.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44430
2015-02-13 07:29:32 +00:00