WNDR3400v2 is based on BCM53xx . Image that is created breaks the router somehow therefore "#".
CFE and NVRAM contain different vars - example:
CFE line original: Device eth0: hwaddr 74-44-01-37-C6-69, ipaddr 192.168.1.1, mask 255.255.255.0
CFE after openwrt: Device eth0: hwaddr 00-FF-FF-FF-FF-FF, ipaddr 192.168.1.1, mask 255.255.255.0
Logs were posted earlier on this mailing list: https://lists.openwrt.org/pipermail/openwrt-devel/2012-July/016174.html
Different logs with factory firmware are in the wiki: http://wiki.openwrt.org/toh/netgear/wndr3400#wndr3400v2
(and on wikidevi for example)
Signed off by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 35790
Added support for the TP-LINK TL-WA830RE v1 Range Extender.
Based on the WA901ND v1 support. Hardware IDs checked against
original firmware. Patch was successfully tested on hardware.
Signed-off-by: Ronald Hecht <ronald.hecht@gmx.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35789
The NO_IRQ symbol is not used by the amba core since
upstream commit:
dfb85185bda373a70409c70c2632b02fb0f8f449
AMBA: get rid of last two uses of NO_IRQ
This gets rid of the last two users of NO_IRQ in AMBA primecell
drivers.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35748
The amba core throws a warning if -1 is used as an
irq value since upstream commit:
2eac58d5026e4ec8b17ff8b62877fea9e1d2f1b3
ARM: amba: make use of -1 IRQs warn
Make the core warn about the use of -1 (NO_IRQ)
Cange the value of the unused IRQs to zero for the
UART devices to get rid of the warning.
Based on #12729.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35747
Use the same MAC addresses as the original firmware.
Based on a patch from #10421.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Tested-by: Gabor Varga <vargagab@gmail.com>
SVN-Revision: 35730
This builds and boots.
Because of the function pointer indirection (e.g. mtd_info's read
function pointer is assigned to spiflash_read), it is difficult for me
to understand where the calls are coming from (could be anywhere,
conditionally pointing at spiflash versions), so I punted and used the
renamed function pointers (_erase, _read, _write). If someone knows
better what to do, please fix.
Cleaned up other sundry kernel tracking issues like get_phy_id and
__devinit,etc.
[juhosg: don't switch to that yet]
Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35727
Setting this bit stops BCM53125 (bgmac actually) from receiving any
packets. This bit is cleared conditionally in b53_switch_reset and it
seems the same is done in bcmrobo.c which never sets that bit again.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 35723
The Broadcom switch driver says that vlan0 should not be used with any switch other than bcm5325.
This makes OpenWrt always use vlan1 and vlan2 instead.
SVN-Revision: 35704
Gabor Juhos
Hauke Mehrtens
Jonas Gorski
Florian Fainelli