This remedies an issue with the MBL Duo if both disks are inserted
and contain OpenWrt. kernel and dtb would be loaded from SATA 1:1
while rootfs (/dev/sda2) would be mounted on SATA 0:1.
Such a mix&match would obviously only work if both OpenWrt versions/
builds are identical, and especially fail after sysupgrade upgraded
the system disk on SATA 0:1.
The fallback to SATA 1:1 needs to be kept for MBL Single (only has
SATA 1:1) and MBL Duo with one disk inserted on SATA 1:1. To speed
up booting in those cases, the unneccesarily doubled "sata init"
will only be called once. (In theory it could be omitted completely
since the on-flash boot script already initializes SATA to load the
on-disk boot script.)
Tested on MBL Duo (all possible combination of disks) and MBL Single
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Freddy Leitner <hello@square.wf>
- fix single spaces hidden by a tab
- replace indentation with spaces by tabs
- make empty lines empty
- drop trailing whitespace
- drop unnecessary blank lines
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
The upgrade led is only used if a running led is defined. If no running
led is defined, the upgrade led is ignored and upgrade isn't indicated
at all.
Instead, turn off the running led prior to turning the upgrade led on.
In most cases there isn't any visual change, but it allows to use an
independent led for upgrade indication.
Signed-off-by: Mathias Kresin <dev@kresin.me>
convert the usb and both sata port power related gpio-hogs to
what they really are: fixed-regulators.
The ethernet phy-reset gpio-hog is replaced by a proper
upstream (4.15+) reset-gpios property in the mdio-node.
So this will work eventually.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
@vahid-dan reported a issue with extracting the rpi images with
Gnome's Archive Manager:
"Ubuntu Archive Manager cannot extract the file and it just
throws a general error message: "An error occurred while
extracting files".
<https://forum.lede-project.org/t/corrupted-pre-built-v18-06-0-rc2-image-for-rpi>
The MBL's rootfs.img.gz image is generated in much the same way.
Hence this patch preemptively splits the rootfs.img.gz image into
a sysupgrade and a factory image.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for squashfs as the root filesystem.
advantages:
- migrate from a existing -ext4 installation and back
with the sysupgrade utility
- existing partition layout will not be lost during switch
- slightly smaller image size as compared to the -ext4 image.
disadvantages:
- needs f2fs + tools. This is because fstools rootdisk.c decides based
on the partition size (currently root partitions > 100 MiB) f2fs is
used as the rootfs_data filesystem.
- rootfs_data is placed into the rootfs partition after the squashfs.
This makes it difficult for tools that expect a /dev/sda${X} device.
It also makes it difficult for data recovery tools as they might not
expect to find a embedded partition or will be slightly confused.
... or will not support f2fs.
For people with existing build configurations: make sure to include mkf2fs
and f2fsck packages into the image. Otherwise the new -squashfs image will
only boot from the ram-overlay.
Note:
All overlay data (configurations/all installed packages/...) will be
placed in inside the rootfs partition (i.e. /dev/sda2) just after the
squashfs image.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
By takimata:
"Come to think of it, an MBL Single board boots up just fine on an
MBL Duo image, and the MBL Single board identifies completely
identical to the MBL Duo
(Board: Apollo-3G - APM82181 Board, 2*SATA, 1*USB).
I wonder if there is any downside to just using the MBL Duo firmware
on a MBL Single. I wonder if the two firmwares could even be unified."
<https://forum.lede-project.org/t/wd-mybook-live-duo-two-disks/16195/9>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The original vendor's driver programmed the dma controller's
AHB HPROT values to enable bufferable, privileged mode. This
along with the "same priorty for both channels" could very
well fix the freezes that have been reported on the forum by
@ticerex and @takimata.
<https://forum.lede-project.org/t/wd-mybook-live-duo-two-disks/16195/46>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
THIN_ARCHIVES option is enabled by default in the kernel configuration
and no one target config disables it. So enable it by default and remove
this symbol from target specific configs to keep them light.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols
are enabled. Both of these symbols are enabled by default in the
generic config, so enable FUTEX_PI by default too to keep platform
specific configs minimal.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have
OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config
of 4.14 and remove this option from platform specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST
which is disable by default, so disable DRM_LIB_RANDOM by default too.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
These options do not used by any supported arch, so disable them by
default to make arch configs a bit more clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Only one arch (x86_64) enables this option. So disable
ARCH_WANTS_THP_SWAP by default and remove referencies to it from all
configs (except x86_64) to make them clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
This patch backports several patches that went upstream into
Herbert Xu's cryptodev-2.6 tree:
crypto: Use zeroing memory allocator instead of allocator/memset
crypto: crypto4xx - performance optimizations
crypto: crypto4xx - convert to skcipher
crypto: crypto4xx - avoid VLA use
crypto: crypto4xx - add aes-ctr support
crypto: crypto4xx - properly set IV after de- and encrypt
crypto: crypto4xx - extend aead fallback checks
crypto: crypto4xx - put temporary dst sg into request ctx
The older, outstanding patches from 120-wxyz series have been
upstreamed as well and therefore they have been reassigned to
fit into the series.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The swconfig package is part of the DEFAULT_PACKAGES list in
the apm821xx's nand subtarget. It's enabled by default because
the MX60(W) and WNDR4700 need it for their initramfs. However
the package is not necessary for the MR24's sysupgrade image, as
the MR24 does not have a switch.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Merge the two existing functions and use a parameter for the type
header field.
It updates the syntax of the former mpc85xx fake ramdisk header
command to be compatible with mkimage from u-boot 2018.03 and fixes the
build error spotted by the build bot.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The MX60's uboot disables all the PHYs before starting linux.
This causes the PHY/switch detection code to malfunction
almost all of the time. To get around this, set a compatible
flag to force PHYID.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This patch cleans and reworks the WNDR4700 dts to increase the
now combined dtb+kernel partition to 3.5 MiB. This has become
necessary due to the switch to GCC 7.3 and the ever increasing
kernel binary size.
The dtb+kernel partition was combined in order to finally
fix the problem with out-of-sync device-trees. From now
on, the kernel and device-tree will always be updated together.
Upgrade Note:
Existing installations will have to use the TFTP firmware
recovery option in order to install the update. Affected users
are advised to make a backup of their existing configuration
prior to running sysupgrade:
<https://openwrt.org/docs/guide-user/installation/generic.backup#backup_openwrt_configuration>
Due to the repartitioning of the NAND, the generated backup
should be placed on either the internal HDD, an attached
USB-Stick or on another PC (externally).
To manually trigger the firmware recovery, the reset button has
to be pressed (and hold) during boot. U-boot will enter the "Upgrade
Mode" and starts a tftpserver listening on 192.168.1.1 for a
tftp client from one of the four LAN/Ethernet ports to connect and
upload the new system: (enable tftp binary mode!).
openwrt-apm821xx-nand-netgear_wndr4700-squashfs-factory.img
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The recent change to switch to gcc 7.3 broke the image
generation code, as the kernel would no longer fit into
KERNEL_SIZE.
This patch fixes the issue by reworking the initramfs
creation and packaging, which will get rid of the
KERNEL_SIZE check in the process.
This new initramfs can be loaded through the MR24 U-boot
in the following way:
=> setenv ipaddr 192.168.1.1
=> setenv bootargs console=ttyS0,$baudrate
=> tftpboot c00000 192.168.1.2:meraki_mr24-initramfs-kernel.bin
[...]
Load address: 0xc00000
Loading: ################################################ [...]
done
Bytes transferred = 5952544 (5ad420 hex)
=> bootm $fileaddr
\## Booting kernel from Legacy Image at 00c00000 ...
...
For more information and the latest flashing guide:
please visit the OpenWrt Wiki Page for the MR24:
<https://openwrt.org/toh/meraki/mr24#flashing>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Right patch version this time, sorry!
* Patch 180-usb-xhci-add-support-for-performing-fake-doorbell.patch had to be adjusted slightly because of upstream adapted code.
* Refreshed patches.
Compile-tested: ramips/mt7621, x86/64
Run-tested: ramips/mt7621, x86/64
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Rosen Penev <rosenp@gmail.com>
The missing CONFIG_USB_XHCI_PCI dependency on CONFIG_USB_PCI of the
µPD720201 xhci-pci(e) usb 3.0 chip used by the WNDR4700 was fixed with
6112abf186 ("kernel: enable CONFIG_USB_PCI for PCI usb modules").
Commit c38fb58576 ("kernel: fix disabling common usb quirks on 4.14")
finally fixed the following build error:
drivers/usb/host/xhci-pci.c: In function 'xhci_pci_probe':
drivers/usb/host/xhci-pci.c:749:6: error: implicit declaration of function 'usb_xhci_needs_pci_reset' [-Werror=implicit-function-declaration]
if (usb_xhci_needs_pci_reset(dev)) {
Hence the CONFIG_USB_PCI symbol isn't required any longer in target kernel
config.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Calling nand_do_upgrade() from platform_pre_upgrade() was deprecated
with 30f61a34b4 ("base-files: always use staged sysupgrade").
Update the platform upgrade code to use platform_do_upgrade() for NAND
images as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The watchdog kill command was meant for busybox watchdog. Busybox watchdog
was replaced by the procd watchdog mid 2013 with commit df7ce9301a
("busybox: disable the watchdog utility by default"), which makes the kill
command obsolete since quite some time.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch updates the apm821xx target to use the 4.14 kernel.
4.14 finally ships with a driver for the WNDR4700's tc654 fan
controller. The custom driver is deprecated in favor of the
upstream driver and the thermal cooling definitions in the DTS
are updated.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch converts all apm821xx devices to the device-tree
board-detection method. All instances of the legacy
boardnames (mbl,mr24,...) are converted to "vendor,device"
identifier.
The custom board-detection code in apm821xx.sh is removed as
it no longer serves any purpose.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch enables metadata-supported image verification
for all apm821xx supported devices. Since this method comes
with a built-in image verification tool (fwtool), the previous
image checks can be removed.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Currently, the device name handle does not include the
manufacturer. This can make it hard do differentiate
between products from different vendors that have the
same product name. As the handle is used to derive
the image name.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch rename all the DT source files in order to
match upstream's "manufacturer-device.dts" format.
Please note that the DEVICE_DTB isn't changed. This is
because the u-boot of the MyBook Live defines the
fdt_file variable to be "apollo3g/apollo3g.dtb".
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Meraki choose to use their product's codename as the main
compatible string. Mathias Kresin commented that this is
a poor choice as this will confuse the users and devs once
the device-tree compatible is used for board-detection and
possible the image name.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch appends the "apm,bluestone" or "amcc,apollo3g"
machine compatible string to the current device tree source.
Please note that unlike other archs the PPC DT code does
not regard the machine's compatible string as a priority
list. This is explained in the kernel's usage-model.txt as follows:
"PowerPC uses a slightly different scheme where it calls the .probe()
hook from each machine_desc, and the first one returning TRUE is used.
However, this approach does not take into account the priority of the
compatible list, and probably should be avoided for new architecture
support."
For this reason, the "apm,bluestone" compatible string can't be
added to the WNDR4700. As otherwise the target specific pci
fix-up code will get ignored and this causes the ath9k WIFI
to not get initialized.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch sets the BOARD_NAME variable on each affected
apm821xx device. The existing DEVICE_PROFILE and
DEVICE_NAME assignments are deprecated as they no longer
serve any purpose.
The BOARD_NAME variable is used by the sysupgrade-tar
method to specifiy a directory overwrite for the
sysupgrade-$dir directory in the generated tar file.
Keeping the original boardname in this context will be
necessary for targets that utilize the sysupgrade-tar
method. Otherwise, sysupgrade on an previous installation
will not recognize the newly generated images.
This step is necessary since an upcoming patch realigns
the existing shortname for a device with a proper
"manufacturer_device" identifier.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The commit 87b668765e
("image: when using the new image build code, gzip ext4 images by default")
forced that all targets that select the ext4 as the root filesystem
to always compress the generated rootfs. This is fine, but this method
doesn't not allow to append the metadata on a per-target base.
Therefore this patch changes the rootfs image production rule to generate
the gzip step manually. This way the metadata can be appended at a later
date.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Advantages:
- preserves existing partition layout. On the hard-drive.
Only the boot and rootfs partition will be overwritten.
Disadvantages:
- The upgrade process takes much longer to run.
from 2-3 seconds to 15-25 seconds.
Please note that sysupgrade will refuse to upgrade, if the existing
installation has an incompatible partition layout. Future changes
to the bootfs and/or rootfs partition size will likely cause breakage
to the sysupgrade procedure. In these cases, the ext4-rootfs.img.gz
has to be written manually onto the disk. Please don't forget to backup
your configuration in this cases.
Note2: This patch requires
"base-files: upgrade: make get_partitions() endian agnostic"
Note3: If your current installation does not host the two
changes, sysupgrading will wipe the existing partition
layout. Don't forget to backup your data!
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Please note that users with a Netgear WNDR4700
will need to update the device-tree partition
manually.
For instructions, please refere to commit 49856a4bb5
("apm821xx: make it possible to update the dtb partition on the WNDR4700")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Freddy Leitner
Paul Wassi
Mathias Kresin
Stijn Tintel
Christian Lamparter
Sergey Ryazanov
Koen Vandeputte
Stijn Segers
Felix Fietkau
Kevin Darbyshire-Bryant
Zoltan HERPAI