Commit Graph

6 Commits (6e4453aecc22aa88c68c1e5d4cf01b2e880bd59e)

Author SHA1 Message Date
Adrian Schmutzler fcb920ffe7 ath79: Consistently label art partition with lower case
This patch harmonizes the label and alias for art partitions
across ath79. Since lower case seems to be more frequent, use that
consistently.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-06-10 11:25:41 +02:00
Adrian Schmutzler 3d153323ab ath79: Consistently label info partition
The info/product-info partition, which frequently contains MAC
adresses, is typically assigned the 'info' alias in DTS, but
then labelled with 'info', 'product-info' or 'config'.

This leads to different aliases if used for setting MAC adresses
in DTS compared to when using e.g. mtd_get_mac_binary. Occationally,
also multiple switch-case entries are used just because of different
labelling.

This patch relabels those partitions in ath79 to consistently use
'info'.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-06-10 11:25:41 +02:00
Petr Štetiar 6648e9458f ath79: set mib-poll-interval on mdio0 attached ar83xx switch
Commit "generic: ar8216: add mib_poll_interval switch attribute" sets
mib-poll-interval as disabled by default (was set to 2s), so it makes
switch LEDs trigger disfunctional on devices which don't have
mib-poll-interval set.

So this patch sets mib-poll-interval to 500ms on devices which have
ar83xx switch connected to mdio0 bus, as the same value was set for
built in switches in 443fc9ac35 ("ath79: use ar8216 for builtin
switch").

Some measurements performed on TP-Link Archer C7-v5:

 mib-type=0, mib-poll-interval=500ms (10s pidstat)

  Average:  %usr %system  %guest   %wait    %CPU   CPU  Command
  Average:  0.00    1.93    0.00    0.00    1.93     -  kworker/0:2

  iperf3 (30s): 334 Mbits/sec

 mib-type=0, mib-poll-interval=2s (10s pidstat)

  Average:  %usr %system  %guest   %wait    %CPU   CPU  Command
  Average:  0.00    1.14    0.00    0.00    1.14     -  kworker/0:2

  iperf3 (30s): 334 Mbits/sec

So it seems like we get 4x faster LED refresh rate for additional 0.8%
CPU load.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-05-20 21:19:48 +02:00
Adrian Schmutzler d8ec6dee49 ath79: Add missing read-only properties
Add some read-only properties to protect partitions from
accidental changes.

Also fixed two whitespaces error on the way.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-05-11 16:37:11 +02:00
David Bauer 6837c757cf ath79: make TP-Link revision naming consistent
This commit makes the TP-Link hardware-revision naming consistent to
match the one used by the vendor. TP-Link refers to the different
revisions as "vX" not "Version X".

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-03-02 13:04:54 +01:00
Skirmantas Lauzikas 9c01273e5e ath79: add support for TP-Link Archer C2 V3 (AC900)
This commit adds support for the TP-link Archer C2 V3 (AC900).

Specifications:

 - CPU: QCA9563 750Mhz
 - Ram: 64MB (DDR2)
 - Flash: 8MB (SPI NOR)
 - Ethernet: 5x 10/100/1000
 - Wifi: QCA9563 bgn + QCA9887 an+ac
 - 9x Leds, 2x buttons

Flash instructions:

Upload openwrt-ath79-generic-tplink_archer-c2-v3-squashfs-factory.bin
via the router Web interface and flash as normal firmware update.

Signed-off-by: Skirmantas Lauzikas <skirmantas.lauzikas@blackraven.lt>
[reorder entries, fix trailing whitespace in dts, add firmware partition
 compatible string, remove led default off states, use default on state
 for system led, reuse tplink-safeloader-uimage image build recipe, squash
 with dynamic partitioning commit, reword commit message, add
 installation instructions]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2019-01-27 16:41:10 +01:00