3c6df9b mt76: rewrite dma descriptor base and ring size on queue reset
30e757e mt76: mt76x02: when setting a key, use PN from mac80211
fa83406 mt76: mt76x2: implement full device restart on watchdog reset
ead881b mt76: mt76x02: do not sync PN for keys with sw_iv set
ba1d989 mt76: mmio: move mt76x02_set_irq_mask in mt76 module
283ebbe mt76: dma: move mt76x02_init_{tx,rx}_queue in mt76 module
b216d3c mt76: introduce q->stopped parameter
8b437d2 mt76x02: clear sta and vif driver data structures on add
2c62d03 mt76x02: clear running flag when resetting state on restart
6b10cfc mt76: mt76x02: only update the base mac address if necessary
669bc49 mt76: mt76x02: reduce false positives in ED/CCA tx blocking
2ed9382 mt76: mt7603: fix tx status HT rate validation
d2c6823 mt76: mt76x2: fix external LNA gain settings
8ee2259 mt76: mt76x2: fix 2.4 GHz channel gain settings
8bfe6d4 mt76: mt7603: clear ps filtering mode before releasing buffered frames
d13b065 mt76: mt7603: fix up hardware queue index for PS filtered packets
eb1ecc4 mt76: mt7603: notify mac80211 about buffered frames in ps queue
3687eec mt76: mt7603: clear the service period on releasing PS filtered packets
42ab27e mt76: when releasing PS frames, end the service period if no frame was found
461f3b0 mt76: mt76x02: disable ED/CCA by default
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ieee80211w support is only activated in hostapd when at least one
capable driver is build into the image. Many drivers which are capable
of ieee80211 (MFP) and have the MFP_CAPABLE set in the driver are still
missing the DRIVER_11W_SUPPORT dependency. Add this to more driver
capable of ieee80211w.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
b514490 iwinfo: add device id for MediaTek MT7603E
e9e1400 iwinfo: more Ralink and MediaTek WiSoC and PCIe chips
cb108c5 iwinfo: fix capitalization of vendor name
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Contains the following change
eeef7b5 blobmsg_json: blobmsg_format_string: do not escape '/'
Resolves FS#2147
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The change was made with the following commands
cd package/utils/busybox/config
../convert_menuconfig.pl ~/git-repo/openwrt/openwrt/build_dir/target-mips_24kc_musl/busybox-1.30.1
convert_defaults.pl has no changes other than overwriting defaults for
BUSYBOX_DEFAULT_FEATURE_IPV6
Resolves FS#2146
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This is to align with upstream change 72089cf ("config: deindent all
help texts") and to make the follow-up change syncing Config.in files
with current busybox version more reviewable
It was made with the following commands
cd package/utils/busybox/config
find . -name 'Config.in' | xargs sed -ir -e 's/^\t \([^ ]\)/\t\1/'
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
consolidate patch 651-rt2x00-remove-unneccesary-code.patch.
fixup the most obvious whitespace problems in RXIQ and TX-LOFT code.
always backup registers bbpr1, bbpr4, bbpr241 and bbpr242 to avoid
compiler warning about them being potentially uninitialized.
no functional changes (intended)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use tested values on shuttle,kd20 and assumed values for
mitrastar,stg-212 and cloudengines,pogoplug*.
akitio users have yet to report back stock flash layout to support
vendor bootloader environment there as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ar has a deterministic (-D) and non-deterministic (-U) mode.
OpenWrt is already using the deterministic mode by default,
but ncurses' configure script force this to be non-deterministic.
Since autoreconf fails to generate a new configure, the configure script
is directly modified.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Hardware
--------
CPU: Qualcomm IPQ4019
RAM: 256M
FLASH: 128M NAND
ETH: QCA8075
VDSL: Intel/Lantiq VRX518 PCIe attached
currently not supported
DECT: Dialog SC14448
currently not supported
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
LED: - Power/DSL green
- WLAN green
- FON/DECT green
- Connect/WPS green
- Info green
- Info red
BTN: - WLAN
- FON
- WPS/Connect
UART: 115200n8 3.3V (located under the Dialog chip)
VCC - RX - TX - GND (Square is VCC)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz7530'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ7530.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz7530.bin uboot0
> mtd write /path/to/uboot-fritz7530.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
[removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Adds support for the AVM FRITZ!Box 7530.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [PKG_RELEASE]
Qxwlan E2600AC C1 based on IPQ4019
Specifications:
SOC: Qualcomm IPQ4019
DRAM: 256 MiB
FLASH: 32 MiB Winbond W25Q256
ETH: Qualcomm QCA8075
WLAN: 5G + 5G/2.4G
* 2T2R 2.4/5 GHz
- QCA4019 hw1.0 (SoC)
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
INPUT: Reset buutton
LED: 1x Power ,6 driven by gpio
SERIAL: UART (J5)
UUSB: USB3.0
POWER: 1x DC jack for main power input (9-24 V)
SLOT: Pcie (J25), sim card (J11), SD card (J51)
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Qxwlan E2600AC C2 based on IPQ4019
Specifications:
SOC: Qualcomm IPQ4019
DRAM: 256 MiB
NOR: 16 MiB Winbond W25Q128
NAND: 128MiB Micron MT29F1G08ABAEAWP
ETH: Qualcomm QCA8075
WLAN: 5G + 5G/2.4G
* 2T2R 2.4/5 GHz
- QCA4019 hw1.0 (SoC)
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
INPUT: Reset buutton
LED: 1x Power, 6 driven by gpio
SERIAL: UART (J5)
USB: USB3.0
POWER: 1x DC jack for main power input (9-24 V)
SLOT: Pcie (J25), sim card (J11), SD card (J51)
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "ubi" filename to "ubi-firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "ubi" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
[ added rng node. whitespace fixes, ported 02_network,
ipq-wifi Makefile, misc dts fixes, trivial message changes ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* wg-quick: freebsd: allow loopback to work
FreeBSD adds a route for point-to-point destination addresses. We don't
really want to specify any destination address, but unfortunately we
have to. Before we tried to cheat by giving our own address as the
destination, but this had the unfortunate effect of preventing
loopback from working on our local ip address. We work around this with
yet another kludge: we set the destination address to 127.0.0.1. Since
127.0.0.1 is already assigned to an interface, this has the same effect
of not specifying a destination address, and therefore we accomplish the
intended behavior. Note that the bad behavior is still present in Darwin,
where such workaround does not exist.
* tools: remove unused check phony declaration
* highlighter: when subtracting char, cast to unsigned
* chacha20: name enums
* tools: fight compiler slightly harder
* tools: c_acc doesn't need to be initialized
* queueing: more reasonable allocator function convention
Usual nits.
* systemd: wg-quick should depend on nss-lookup.target
Since wg-quick(8) calls wg(8) which does hostname lookups, we should
probably only run this after we're allowed to look up hostnames.
* compat: backport ALIGN_DOWN
* noise: whiten the nanoseconds portion of the timestamp
This mitigates unrelated sidechannel attacks that think they can turn
WireGuard into a useful time oracle.
* hashtables: decouple hashtable allocations from the main device allocation
The hashtable allocations are quite large, and cause the device allocation in
the net framework to stall sometimes while it tries to find a contiguous
region that can fit the device struct. To fix the allocation stalls, decouple
the hashtable allocations from the device allocation and allocate the
hashtables with kvmalloc's implicit __GFP_NORETRY so that the allocations fall
back to vmalloc with little resistance.
* chacha20poly1305: permit unaligned strides on certain platforms
The map allocations required to fix this are mostly slower than unaligned
paths.
* noise: store clamped key instead of raw key
This causes `wg show` to now show the right thing. Useful for doing
comparisons.
* compat: ipv6_stub is sometimes null
On ancient kernels, ipv6_stub is sometimes null in cases where IPv6 has
been disabled with a command line flag or other failures.
* Makefile: don't duplicate code in install and modules-install
* Makefile: make the depmod path configurable
* queueing: net-next has changed signature of skb_probe_transport_header
A 5.1 change. This could change again, but for now it allows us to keep this
snapshot aligned with our upstream submissions.
* netlink: don't remove allowed ips for new peers
* peer: only synchronize_rcu_bh and traverse trie once when removing all peers
* allowedips: maintain per-peer list of allowedips
This is a rather big and important change that makes it much much faster to do
operations involving thousands of peers. Batch peer/allowedip addition and
clearing is several orders of magnitude faster now.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
This is bugfix release that incorporated all of the devcrypto engine
patches currently in the tree.
The cleaning procedure in Package/Configure was not removing the
dependency files, causing linking errors during a rebuild with
different options. It was replaced by a simple make clean.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
omcproxy's configuration is lost on every update or installation.
Avoid it by defining the configuration file.
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
After update to 5.0.1 iw-full package failed to display command list on
ipq40xx arch. Root cause was found to be LTO reordering causing
incorrect detection of command struct size in:
iw.c:552
cmd_size = labs((long)&__section_set - (long)&__section_get);
This reverts commit ef16a394d2.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
If no mcast_rate is set for the wifi-iface then there is no rate_idx (0)
set for the bss. This can break for example 5GHz meshpoint interfaces
because 0 maps to a CCK rate (11Mbit/s).
It must also be avoided that the ath10k-ct internal state for the rates is
not synced with the mac80211 rates state. Otherwise, the user specified
rate (e.g. a wifi-iface mcast_rate for a meshpoint interface) will only be
set on startup. And a short while after that, ath10k-ct specific code in
ath10k_check_apply_special_rates is missing a valid rate in its own
structures and is then recalculating a new default rate. This default rate
is in most situations not the requested rate.
Fixes: 4df3c71cd4 ("ath10k-ct: Update to 2018-12-11 and use version based on 4.19")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
If no mcast_rate is set for the wifi-iface then there is no rate_idx (0)
set for the bss. This breaks for example 5GHz meshpoint interfaces because
0 maps to a CCK rate (11Mbit/s).
Fixes: db90c243a0 ("mac80211: update to version based on 4.19-rc4")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This should fix the WDS / 4addr mode with ath10k and probably other
devices.
This patch was found here: https://patchwork.kernel.org/patch/10692383/
Fixes: d9eefa7a70 ("mac80211: rebase ontop of v4.18.5")
Reported-by: Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix crash due to passing invalid r2x00dev->eeprom_file pointer to
release_firmware(). Since we copy eeprom data with EEPROM_SIZE
in rt2800_read_eeprom() we can use eeprom_file->size as marker
if the file was crated by request_firmware().
Acked-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
On targets that don't have input support enabled in the kernel config,
building kmod-input-touchscreen-ads7846 fails due to a missing
dependency on kmod-input-core. Add the dependency to fix this.
Fixes: 77a54bbf13 ("kernel: add kmod-input-touchscreen-ads7846")
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
max_ttl - limit the ttl in the dns answer if greater as $max_ttl
min_cache_ttl - force caching of dns answers even the ttl in the answer
is lower than the $min_cache_ttl
max_cache_ttl - cache only dns answer for $max_cache_ttl.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
This module adds support for ADS7846 based touchscreens used in devices
like the WaveShare 3.5" and 4" LCD displays designed for Raspberry Pi.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This module adds support for the ILI9486 LCD controller used in devices
like the Waveshare 3.5" and 4" LCD displays designed for Raspberry Pi.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This module adds support for small TFT LCD display modules. While this
module also exists in the 4.9 kernel, we are not going to support this
kernel in the next major release, so don't make it available for 4.9.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The kernel modules that provide support for framebuffers in system RAM
are currently included in the kmod-drm-imx package. Move them to a
separate package, so that other modules can depend on them.
Increase the autoload order of the drm-imx* packages to load the modules
after loading the fb modules they depend on.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This makes it clear that localuse when explicitly specified in the
config will have its final say on whether or not the initscript should
touch /etc/resolv.conf, no matter whatever the result of previous
guesswork would be
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This commit updates the file "board-linksys_ea6359v3".
Without this commit, the Linksys EA6350v3 will experience poor wireless
performance in both bands. With this patch, wireless performace will be
comparable to the performance of the stock firmware.
Signed-off-by: Oever González <notengobattery@gmail.com>
The board-files are specific to the target and device. Hence
they need to be set as nonshared. Otherwise they do not show
up on the package repository. This causes problems for
imagebuilder, if it needs to build a image for a specific
device that hasn't had the time to have get its boardfile
upstream.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Apparently this modem replies differently to attempted --get-pin-status
which makes the script fail if a pincode is set. Fix this.
Manufacturer: Sierra Wireless, Incorporated
Model: MC7455
Revision: SWI9X30C_02.24.05.06 r7040 CARMD-EV-FRMWR2 2017/05/19 06:23:09
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Cherry-pick Multi-AP commits from uptream:
9c06f0f6a hostapd: Add Multi-AP protocol support
5abc7823b wpa_supplicant: Add Multi-AP backhaul STA support
a1debd338 tests: Refactor test_multi_ap
bfcdac1c8 Multi-AP: Don't reject backhaul STA on fronthaul BSS
cb3c156e7 tests: Update multi_ap_fronthaul_on_ap to match implementation
56a2d788f WPS: Add multi_ap_subelem to wps_build_wfa_ext()
83ebf5586 wpa_supplicant: Support Multi-AP backhaul STA onboarding with WPS
66819b07b hostapd: Support Multi-AP backhaul STA onboarding with WPS
8682f384c hostapd: Add README-MULTI-AP
b1daf498a tests: Multi-AP WPS provisioning
Add support for Multi-AP to the UCI configuration. Every wifi-iface gets
an option 'multi_ap'. For APs, its value can be 0 (multi-AP support
disabled), 1 (backhaul AP), 2 (fronthaul AP), or 3 (fronthaul + backhaul
AP). For STAs, it can be 0 (not a backhaul STA) or 1 (backhaul STA, can
only associate with backhaul AP).
Also add new optional parameter to wps_start ubus call of
wpa_supplicant to indicate that a Multi-AP backhaul link is required.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Those have by now been merged into wireless-drivers-next:
17ae2acd1a6f rt2x00: remove unneeded check
5991a2ecd070 rt2x00: remove confusing AGC register
9ad3b5565445 rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band
7aca14885ede rt2800: enable TX_PIN_CFG_RFRX_EN only for MT7620
c7ff1bfeaf1c rt2800: comment and simplify AGC init for RT6352
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Currently these kernel packages only work on x86, restrict them to that
target.
Fixes: 2f239c02a0 ("x86: video: add amdgpu DRM kernel package")
Fixes: 2f6918ee9b ("x86: video: add radeon DRM module support")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit e6d84fa886 as it breaks the
installation of the iproute2 utilities ip-bridge, ss, nstat, devlink and rdma
for the ip-full variant
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This reverts commit 26681fa6a6 as it breaks the
installation of the iproute2 utilities ip-bridge, ss, nstat, devlink and rdma
for the ip-full variant
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Felix Fietkau
Hauke Mehrtens
Daniel Golle
Yousong Zhou
Alexander Couzens
David Bauer
张鹏
Jason A. Donenfeld
Eneas U de Queiroz
Hans Dedecker
David Santamaría Rogado
Mantas Pucka
Daniel Engberg
Matt Merhar
Aleksander Jan Bajkowski
Sven Eckelmann
Stanislaw Gruszka
Piotr Dymacz
Stijn Tintel
Rafał Miłecki
Oever González
Christian Lamparter
Arnout Vandecappelle (Essensium/Mind)