Buffalo LinkStation LS421DE is a dual bay NAS, based on Marvell Armada 370
Hardware:
SoC: Marvell Armada 88F6707-A1
CPU: Cortex-A9 1200 MHz, 1 core
Flash: SPI-NOR 1 MiB, NAND 512 MiB
RAM: DDR3 512 MiB
Ethernet: 1x 10/100/1000 Mbps
USB: 1x 2.0, 1x 3.0
SATA: 2x 3.0 Gbps
LEDs/Input : 5x / 2x (1x button, 1x slide-switch)
RTC: Ricoh RS5C372A, I2C, no battery
Flash instruction (UART+TFTP):
1. Downgrade the OEM firmware to 1.34 version (BUFFALO_BOOTVER=0.13)
2. Remove any hard drive from inside the bays.
3. Boot the Openwrt initramfs image using the U-Boot serial console:
tftpboot 0x1200000 buffalo_ls421de-initramfs-kernel.bin
bootm 0x1200000
4. Flash the sysupgrade image using the Openwrt console:
sysupgrade -n buffalo_ls421de-squashfs-sysupgrade.bin
5. Wait until it finish, the device will reboot with Openwrt installed
on the NAND flash.
Note:
- Device shuting down doesn't work, even if the power slide switch is
used. We must first, via MDIO, set the unused LED2 at the ethernet
phy0 to off state. Reboot works ok.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Armada 370 processors have only 16 double-precision registers. The
change introduced by 8dcc108760 ("toolchain: ARM: Fix toolchain
compilation for gcc 8.x") switched accidentally the toolchain for mvebu
cortexa9 subtarget to cpu type with 32 double-precision registers. This
stems from gcc defaults which assume "vfpv3-d32" if only "vfpv3" as mfpu
is specified. That change resulted in unusable image, in which kernel
will kill userspace as soon as it causing "Illegal instruction".
Ref: https://forum.openwrt.org/t/gcc-was-broken-on-mvebu-armada-370-device-after-commit-on-2019-03-25/43272
Fixes: 8dcc108760 ("toolchain: ARM: Fix toolchain compilation for
gcc 8.x")
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Place DEVICE_VARS assignments at the top of the file or above Device/Default
to make them easier to find.
For ramips, remove redundant values already present in parent file.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There is no such role as target maintainer anymore, one should always
send corresponding changes for the review and anyone from the commiters
is allowed to merge them or eventually use the hand break and NACK them.
Lets make it clear, that it is solely a community doing the maintenance
tasks.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
Currently kmod-i2c-mux-* will not get into images unless kmod-i2c-mux is added
to DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-i2c-mux-pca954x
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This commit removes the target-specific diag.sh script. This way, the
generic one is used for the target, which uses DT-aliases to specify the
LEDs used.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Ansuel Smith <ansuelsmth@gmail.com> [wrt3200acm @ 5.4]
Currently kmod-i2c-* will not get into images unless kmod-i2c-core is added to
DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-hwmon-lm75
- kmod-i2c-gpio
- kmod-i2c-gpio-custom
- kmod-i2c-mux
- kmod-i2c-ralink
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300 ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
If device recipe has specified DEVICE_DTS variable, the dtb is built
anyway by OpenWrt buildroot image rules. Drop the patch and adjust the
location of compiled dtb.
Cc: Scott Roberts <ttocsr@gmail.com>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tar has ability to change current dir, so use that instead additional
command invocation. Also being here, change tar arguments to make final
archive reproducible.
Cc: Scott Roberts <ttocsr@gmail.com>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This device receipe selects bunch of packages which some are re-defined,
unnecessary or irrelevant. Clean them up, so only basic functionality
persist.
Cc: Scott Roberts <ttocsr@gmail.com>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Don't rewrite global DTS_DIR, instead, use proper variable for
specifying devices dts directory. For consistency, also specify the
variable in default profile, as suggested by Adrian Schmutzler.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Align subtargets makefiles names to actual subtargets.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This sorts the devices in image Makefiles alphabetically.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[fixed sorting in one case, add commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
"[[" is a bash extension for test. As the ash-implementation is not
fully compatible we drop its usage.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[split patch, remove shebang, adjust commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Update the uDPU kernel support, fixing a number of issues:
* make ethernet work again by adding comphy definitions
* slow the I2C bus to give it more chance of actually working
* the SFP cages are designed to support up to 3W modules, which
would be prevented from initialising without this patch.
Signed-off-by: Russell King <linux@armlinux.org.uk>
[jonas.gorski: rename to mvebu, refresh patches]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Move two phylink patches from mvebu to generic, so that everyone can
benefit from them.
Signed-off-by: Russell King <linux@armlinux.org.uk>
[jonas.gorski: add kernel version to file names]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Remove the old phylink/SFP patches from the OpenWRT build; these will
be updated with a new set in subsequent.
450-reprobe_sfp_phy is also removed for several reasons:
1) it is not in mainline.
2) it breaks copper modules that do not have a PHY.
3) it makes backporting the current patch set harder.
Discussion is ongoing with the patch author for a mainline Linux kernel
patch for this.
Signed-off-by: Russell King <linux@armlinux.org.uk>
For the mvebu target in particular, there is a lot of files in
base-files that are only relevant for one subtarget. Improve
overview and reduce size per subtarget by moving/splitting
base-files depending on the subtarget they belong to.
While at it, consolidate 01_leds by using the model part of
the board name as variable.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This introduces the SOC variable to mvebu target to derive some of
the DEVICE_DTS variables based on the SOC prefix and the device
definition name.
Since DTS names and compatible are inconsistent also in the kernel
for this target, the scheme cannot be applied to all devices, though.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This moves the if conditions for choosing which image Makefiles
are used to the parent image/Makefile. It seems more convenient
to have "codeflow" in the parent while the subtarget-specific
files only contain the definitions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Handle both variants separately. This removes the need for calling
swconfig to detect the switch, and simplifies future changes.
Signed-off-by: Josua Mayer <josua.mayer@jm0.eu>
There is nothing that needs bash anymore.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[add prefix to commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Enables proper checking. Matches printf behavior in C.
Found with shellcheck.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[add prefix to commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
let is a bashism.
Found with shellcheck.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[add prefix to commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Remove CC_HAS_ASM_GOTO, CC_IS_GCC and GCC_VERSION kernel config options
which are set at runtime and which should be ignored now.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
These targets are currently using more or less same SIGNATURE variable
which provides unique partition ID/signature, so it makes sense to
refactor it out into common IMG_PART_SIGNATURE variable which could be
reused by all targets.
This is another step in the direction of reproducible OpenWrt images.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[split into separate commit, renamed to IMG_PART_SIGNATURE]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
UUID of ext4 volumes generated by make_ext4fs are determined by volume
label and it will all be 57f8f4bc-abf4-655f-bf67-946fc0f9f25b when label
is empty
Labeling them does not make them unique but tools like block command
from fstools have a better chance differentiating them
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
These patches backport support for the ARMADA 3700 COMPHY driver.
Also backported is the mvneta driver. This will allow switching
the SGMII speed using SMC calls. To support this you must update
the firmware using Marvells 18.12 version (this has now been
upstreamed). The mvneta driver allows 2500basex and 2500baset.
Signed-off-by: Scott Roberts <ttocsr@gmail.com>
This refreshes the kernel 4.19 configuration, it looks like this was not
done initially.
When did a compile with the default settings I had to select some
kernel configuration options.
Fixes: 98684d99b2 ("mvebu: add kernel 4.19 support")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This replaces deprecated backticks by more versatile $(...) syntax.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[decapitalized patch subject at submitter's request]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This replaces deprecated backticks by more versatile $(...) syntax.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[decapitalized patch subject at submitter's request]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
It's a variable set by procd that should replace hardcoded
/tmp/sysupgrade.tgz.
This change requires the most recent procd with the commit 0f3c136
("sysupgrade: set UPGRADE_BACKUP env variable").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
$CONF_TAR shouldn't be assumed to always point to the sysupgrade.tgz.
This change makes code more generic and allows refactoring $CONF_TAR.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
1) Add BACKUP_FILE and use it when copying an archive to be restored
after sysupgrade (on the next preinit).
2) Use CONF_TAR for copying backup prepared by the /sbin/sysupgrade
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
According to 02_network, eth0.1 is LAN and eth1.2 is WAN,
but $mac_wan was assigned incorrectly to eth0 in preinit.
Swap eth0 and eth1 to fix this.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
This patch adds sysupgrade, uboot-env and networking support
for Methode uDPU device.
Device features 4 partitions:
-----------------------------------------
| boot | recovery | rootfs | misc |
| (ext4) | (ext4) | (fsf2) | (f2fs) |
_________________________________________
Idea was to use f2fs only but the u-boot currently lacks support
so first 2 partition are ext4 to be u-boot readable, and this was
a reason why custom build and sysupgrade sections were required.
On the sysupgrade, boot and rootfs partitions are updated, firmare
image and user configuration is saved on the misc partition and if
the upgrade was successfull, recovery partition will be updated on
after the reboot from preinit script. If the sysupgrade fails for any
reason, device will fallback to recovery initramfs image.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
This explicitly lets stage2 know if partitions should be preserved. No
more "touch /tmp/sysupgrade.always.overwrite.bootdisk.partmap" hack.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This commit made the following changes to sync all bootcount scripts:
1. use boot() instead of start()
This script only needs to be executed once when boot is complete.
use boot() to make this explicit.
2. drop sourcing of /lib/functions.sh
This is aready done in /etc/rc.common.
3. ramips: replace board name checking with a case
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Unconditionally execute the final case statement, even if the disk layout
changed. This is necessary, to keep the original Turris Omnia flash
instructions working: The disk layout WILL change, when switching from
TurrisOS to OpenWRT. Without updating the uboot environment at the same
time, the user would end up with an unbootable system.
Fixes commit 2e5a0b81ec ("mvebu: sysupgrade: sdcard: keep user added ...")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
These legacy bindings were removed long time ago from dts, so there's no
need to keep support for them.
Spotted-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This commit fixes regression on Linksys WRT1900 (Mamba) where this device
doesn't have USB 3.0 controller integrated in SoC, instead it has Etron
EJ168 connected to PCIe lane. Previously enabled in kernel 4.4 and 4.9,
was lost in transition to 4.14.
Fixes: 4ccad92 ("mvebu: Add support for kernel 4.14")
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
sysupgrade passes image path to platform_check_image() as an argument so
it can be simply accessed using $1
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This adds initial support for micro-DPU (uDPU) board which is based on
Armada-3720 SoC. micro-DPU is the single-port FTTdp distribution point
unit made by Methode Electronics which offers complete modularity with
replaceable SFP modules both for uplink and downlink (G.hn over
twisted-pair, G.hn over coax, 1G and 2.5G Ethernet over Cat-5e cable).
On-board features:
- 512 MiB DDR3
- 2 x 2.5G SFP via HSGMII SERDES interface to the A3720 SoC
- USB 2.0 Type-C connector
- 4GB eMMC
- ETSI TS 101548 reverse powering via twisted pair (RJ45) or coax (F Type)
uDPU is intented to run on kernel 4.19 on newer due to the SFP and hardware support.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
When the non-generic espressobin targets were added these board checks
were not updated. One side effect of this is that config is not saved
during an upgrade of -emmc,-v7, or -v7-emmc devices.
Signed-off-by: Brett Mastbergen <bmastbergen@untangle.com>
When targets for multiple ESPRESSObin devices were added, not all
files were updated which means any ESPRESSObin version beside generic
won't have proper networking, sysupgrade and uboot-env. This patch
fixes the issue.
* fixup network detection
* fixup uboot-env
* fixup platform.sh for sysupgrade
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Not all versions of ESPRESSObin require SD card, but can
be booted from the internal emmc flash (mmc dev 1) instead.
Add a simple check in the bootscript to see which mmc device
is detected and boot from it using mmcdev variable.
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Lets bump kernel to 4.19 on targets which were run tested or got ACKed
so we've enough time to make it ready for next release:
armvirt/32 (runtested in qemu)
armvirt/64 (runtested in qemu)
ath79/generic (runtested on Carambola2)
gemini/generic (runtested on DIR-685, DNS-313, SQ201, SL93512R)
imx6/generic (runtested on Apalis)
ipq40xx/generic (runtested on nbg6617)
malta/be64 (runtested in qemu)
malta/be (runtested in qemu)
malta/le (runtested in qemu)
malta/le64 (runtested in qemu)
mpc85xx/generic (runtested on TL-WDR4900)
mpc85xx/p2020 (runtested on P2020RDB)
mvebu/cortexa53
mvebu/cortexa72
mvebu/cortexa10
octeon/generic (runtested on EdgeRouter Lite)
sunxi/cortexa53 (build tested only)
sunxi/cortexa7 (runtested on Lime2-K)
sunxi/cortexa8 (build tested only)
tegra/generic
x86/64 (runtested in qemu)
Acked-by: Zoltan HERPAI <wigyori@uid0.hu> [sunxi]
Tested-by: Linus Walleij <linus.walleij@linaro.org> [gemini]
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [mvebu, tegra]
Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net> [octeon]
Tested-by: Pawel Dembicki <paweldembicki@gmail.com> [mpc85xx/generic mpc85xx/p2020]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
[added sfp related patches from Russell King]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
[rebase; rework patches; separate and cleanup kernel configs;
add espessobin dts; adjust venom dts]
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
err_free_stats has been deprecated. Replace with err_netdev.
Compile-tested on: mvebu
Runtime-tested on: mvebu
Fixes: a7e68927d0 ("kernel: bump 4.14 to 4.14.125 (FS#2305 FS#2297)")
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Refreshed all patches.
This bump contains upstream commits which seem to avoid (not properly fix)
the errors as seen in FS#2305 and FS#2297
Altered patches:
- 403-net-mvneta-convert-to-phylink.patch
- 410-sfp-hack-allow-marvell-10G-phy-support-to-use-SFP.patch
Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Consistently handle boot-count reset and upgrade across
ipq40xx, ipq806x, kirkwood, mvebu
Dual-firmware devices often utilize a specific MTD partition
to record the number of times the boot loader has initiated boot.
Most of these devices are NAND, typically with a 2k erase size.
When this code was ported to the ipq40xx platform, the device in hand
used NOR for this partition, with a 16-byte "record" size. As the
implementation of `mtd resetbc` is by-platform, the hard-coded nature
of this change prevented proper operation of a NAND-based device.
* Unified the "NOR" variant with the rest of the Linksys variants
* Added logging to indicate success and failure
* Provided a meaningful return value for scripting
* "Protected" the use of `mtd resetbc` in start-up scripts so that
failure does not end the boot sequence
* Moved Linksys-specific actions into common `/etc/init.d/bootcount`
For upgrade, these devices need to determine which partition to flash,
as well as set certain U-Boot envirnment variables to change the next
boot to the newly flashed version.
* Moved upgrade-related environment changes out of bootcount
* Combined multiple flashes of environment into single one
* Current-partition detection now handles absence of `boot_part`
Runtime-tested: Linksys EA8300
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[checkpatch.pl fixes, traded split strings for 80+ chars per line]
The driver is for the I2C mux.
Schematic available at https://doc.turris.cz/doc/_media/rtrom01-schema.pdf
Signed-off-by: Josef Schlehofer <josef.schlehofer@nic.cz>
Tested-by: Rosen Penev <rosenp@gmail.com>
This commit adds support for different iterations of ESPRESSObin.
The added variants are:
ESPRESSObin with soldered eMMC,
ESPRESSObin V7, compared to V5 some passive elements changed and ethernet
ports labels positions have been reversed,
ESPRESSObin V7 with soldered eMMC.
Please refer to:
584d7c5 ("mvebu: new subtarget cortex A53")
for instruction how to boot OpenWrt image placed on SD card. It is
advised for owners of V5 and previous with bootloader based on U-Boot
2015.01, to upgrade the latest version available at:
http://espressobin.net/tech-spec.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Convert whole target to Device Tree based board detection instead of
identifying devices by dts file name. With this we can drop mvebu.sh
translation script and rely on common method for model detection.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Add vendors in device names and also rename few device names, for easier
identyfying potential firmware to flash. The vendor and device string is
mainly derived from model/compatipble string in dts from particular
device, but since not all devices are well described, some of the renames
follow marketing names.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Use make syntax to pass the U-Boot image location and boot with root
partitions size, instead of relying on shell functions and variables.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Drop overly complex amount of defines wich are referenced in the same
devices pool and move image recipes to common define, since devices not
using them overwrite it.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
All of U-Boot scripts repeat the same pattern with only Device Tree blob
name changing for respective device. Therefore create generic scripts
which will be altered on demad by image build process, and create
BOOT_SCRIPT variable which can be added to device recipe and will allow
referencing the same script by many device recipes. This will allow to
slim down the ammount of files in buildroot tree and avoid needlessly
incrementing amount of boot scripts if new devices will be added.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
All of arm64 devices have part of variables repeatedly defined. Stack
them to common define, and reference it in each device recipe.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Even if dts is not included in upstream Makefile, it is built anyway by
recipe specified in include/image.mk. Also remove Build/dtb, it's not
used since 3f72f3a ("mvebu: clearfog: include DTB for all variants in
image").
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This removes support for executing old 32 bit applications on 64 bit ARM
and MIPS kernels.
On OpenWrt we normally compile all the user space applications on our
own and do not support third party binary only modules especial not 32
bit applications on 64 bit CPUs.
This reduces the attack surface on such systems and should also save
some memory.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This activates "Emulate Privileged Access Never using TTBR0_EL1
switching" on ARM64.
This should prevent the kernel from reading code from user space in
kernel context.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The correct board_name for the Turris Omnia is armada-385-turris-omnia.
Fixes: 4e8345ff68 ("mvebu: base-files: autodetect upgrade device")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Currently sysupgrade overwrites whole disk and destroys partitions added
by user. Sync the sysupgrade code with the one present in x86 target to
remedy this behaviour.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Since some boards could be also booted from other mediums than SD card,
lets make the upgrade block device autodetected.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Since most of devices using SD card image to boot, use ext4 as boot
files system we can drop fat fs related packages. Also move packages
which are added repeatedly across subtargets to their default packages,
with droping the ones that are enabled in target kernel configugation.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This will allow to drop additional packages and shrink image size.
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This refreshes the current kernel configuration to remove unneeded
options, add some automatically added ones and reorders them. The normal
build did this automatically, so the builds already used this
configuration.
CONFIG_HW_RANDOM_OMAP is explicitly activated for the cortexa72
subtarget because it has an inside-secure,safexcel-eip76 IP core.
This was done with this command on the cortexa9 subtarget:
make kernel_oldconfig
and this one on the other subtargets:
make kernel_oldconfig CONFIG_TARGET=subtarget
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Drop customizations in:
508-arm64-dts-armada-3720-espressobin-wire-up-spi-flash.patch
and move them to separate patch, with broader explanation.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This symbol is enabled in all subtargets, move it to common kernel
config.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Acked-by: Rosen Penev <rosenp@gmail.com>
When using Image Builder and building image for Cortex A53 or
A72 subtargets, it'll fail with following message:
Collected errors:
* opkg_install_cmd: Cannot install package mwlwifi-firmware-88w8864.
* opkg_install_cmd: Cannot install package mwlwifi-firmware-88w8964.
make[2]: *** [Makefile:153: package_install] Error 255
make[1]: *** [Makefile:114: _call_image] Error 2
This is beacuse both packages are available only for Cortex A9 subtarget
and are included in PACKAGES array in default profile. Instead patching
this, let's remove profiles completely, since all necessary packages are
specified in DEVICE_PACKAGES array for each device.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Daniel González Cabanelas
Tomasz Maciej Nowak
Sungbo Eo
Petr Štetiar
Hauke Mehrtens
Koen Vandeputte
Sven Roederer
Russell King
Adrian Schmutzler
Josua Mayer
Rosen Penev
Paul Spooren
Yousong Zhou
Moritz Warning
Scott Roberts
Rafał Miłecki
DENG Qingfang
Vladimir Vid
Chuanhong Guo
Klaus Kudielka
Brett Mastbergen
Marko Ratkaj
George Amanakis
Jeff Kletsky
Josef Schlehofer
Hauke Mehrtens