8411e5c06e
bcm63xx: switch to b53 and swconfig
...
Switch to using the B53 switch driver where appropriate.
Use a non-tagged default config where it isn't confirmed to be
working.
Remove the switch configuration in preinit as the switch will now
be configured by the driver to use port isolation to prevent leakage
between lan and wan.
While at it, also provide a switch config for Neufbox 6.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35307
2013-01-23 10:12:40 +00:00
d8f1fa1e38
switch: ROBO Switch Gigabit MII Support
...
I wrote this patch some time ago because I had a need for one of the
Gigabit ports (Linksys E3000) to be forced to 100FD. This is based
on the robocfg sources included w/ the RT-N16 sources from ASUS.
Since work is progressing on a BGMAC driver that could be included in
OpenWRT, this may be useful to someone else.
In testing, forcing the speed to 10/100 or 1000 worked fine; however,
when trying to force full-duplex mode, the result was always
half-duplex. I was not able to isolate the source of the problem
(this patch, driver or H/W limitation). The only way I could get it
to work was to set the port to Auto, but then only advertise 100FD
(not included in this patch).
I have a modified version of the robocfg package as well, I'd have to
clean it up a little first (remove the full-duplex hack) before
submitting it if there is interest.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 34992
2013-01-03 01:58:01 +00:00
63ec34612c
switch: improve error messages
...
This is in part based on a patch send by Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 34991
2013-01-03 01:57:19 +00:00
25afeba608
brcm47xx: add a new version of the nvram rewrite patch
...
This is the version like it was send for mainline inclusion.
SVN-Revision: 34988
2013-01-03 01:53:30 +00:00
da94d4ac29
switch: warn if ndo_do_ioctl is not implemented in the Ethernet driver
...
SVN-Revision: 33506
2012-09-22 12:29:23 +00:00
bf0974e8da
switch: improve error message
...
SVN-Revision: 33464
2012-09-19 10:57:38 +00:00
40f139b53b
switch: clean up robo switch driver
...
* remove use_et, all supported drivers are using mii ioctls
* remove robo.phy_addr, phy_addr was always set to ROBO_PHY_ADDR.
* remove support for old kernel versions
* do_ioctl is allways called with buff == NULL
* use if_mii
SVN-Revision: 33002
2012-08-05 13:10:43 +00:00
0758996824
brcm47xx: use libgpio instaed of implementing the gpio interface ourself.
...
SVN-Revision: 32992
2012-08-04 19:46:25 +00:00
654f9c879f
switch: the hardware must be up while configuring Since the removal of the interface coldplug hack the timing changed in such a way that eth0 is not up during switch setup, leading to an inaccesible device. Bring up the switch interface before configuring it to mitigate the problem.
...
SVN-Revision: 30937
2012-03-13 21:15:41 +00:00
b9da4dcb6b
switch: fix some memory leaks in switch_parse_vlan()
...
SVN-Revision: 29936
2012-01-28 13:52:37 +00:00
b220442c75
switch: update for brcm47xx target
...
* remove suport for 2.4 kernel
* add support for bcma bus
SVN-Revision: 27904
2011-08-04 20:07:58 +00:00
640927dde3
switch: fix switch-robo device reference counting
...
Fix incorrect device reference counting by switch-robo.
Signed-off-by: George Kashperko <george@znau.edu.ua>
SVN-Revision: 25619
2011-02-20 17:24:15 +00:00
e31542241c
remove whitespaces in kmod-switch sources
...
SVN-Revision: 22320
2010-07-20 22:25:04 +00:00
2d86ea7bf3
massive: replace occurences of .$(LINUX_KMOD_SUFFIX) with .ko after r21950
...
SVN-Revision: 22145
2010-07-12 14:06:13 +00:00
543d870e82
remove linux 2.4 support from several packages
...
SVN-Revision: 21954
2010-06-26 20:43:41 +00:00
501e154d03
switch: explicitely clear port mappings in unsused vlans ( #7082 )
...
SVN-Revision: 20717
2010-04-05 13:51:26 +00:00
2d100861a4
switch: suppress boot error message on 2.4
...
SVN-Revision: 19922
2010-03-01 01:12:57 +00:00
96e4312e7e
switch: eliminate the asterisk from the switch port configuration and set it automatically on the first vlan, this aligns the broadcom vlan config with the swconfig format
...
SVN-Revision: 19909
2010-02-28 16:40:06 +00:00
f4edda27af
switch: do not include linux/autoconf.h ( #6513 )
...
SVN-Revision: 19903
2010-02-28 12:57:57 +00:00
194f32bc26
change switch config to swconfig style format to remain consistent accross platforms
...
SVN-Revision: 18425
2009-11-15 18:43:46 +00:00
5a13cc0726
fix breakage on wl500gp after r18214, thanks sn9 ( #6084 )
...
SVN-Revision: 18289
2009-11-03 20:35:37 +00:00
2d57b56bce
make etehrent work on wrt350n, thx sn9
...
SVN-Revision: 18214
2009-10-29 21:26:36 +00:00
8673372e20
add patches for kernel 2.6.31
...
This is completly untested. Only a compile tests with the default config was done!
SVN-Revision: 17734
2009-09-26 11:48:48 +00:00
369db35a29
fix oops in switch-robo on brcm63xx, thanks to Daniel Dickinson ( #5053 )
...
SVN-Revision: 15611
2009-05-05 06:32:45 +00:00
9051239daf
prevent kmod-switch from accessing nvram on brcm63xx ( #5035 )
...
SVN-Revision: 15555
2009-05-02 10:01:09 +00:00
210254c279
fix nvram_get checking on non-WGT634U ( #4975 )
...
SVN-Revision: 15319
2009-04-21 09:25:51 +00:00
6f80c9cc7c
fix strange LED behavior with Netgear WGT634U ( #3552 )
...
SVN-Revision: 15290
2009-04-20 10:27:46 +00:00
34939cad39
get rid of $Id$ - it has never helped us and it has broken too many patches ;)
...
SVN-Revision: 15242
2009-04-17 14:09:46 +00:00
04909ca614
allow kmod-switch to be used on brcm63xx ( #4599 )
...
SVN-Revision: 14825
2009-03-09 21:57:11 +00:00
529e87f6c5
switch: remove message about BFL_ENETADM not being set on systems with a roboswitch
...
SVN-Revision: 13100
2008-11-02 23:14:16 +00:00
40990382e5
(4/6) bcm57xx: switch-core.c/switch-robo.c check for port already registered
...
This patch prevents switch-robo.c from attempting robo_probe on a port
that is already registered. robo_probe will adjust kernel reference counts
if it detects a switch on the port. If this patch wasn't applied, the
wrt350n would hang on reboot, waiting for the network driver reference count
to reach zero indefinitely.
Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu>
SVN-Revision: 11469
2008-06-15 11:10:27 +00:00
f027ecb2cf
Stopgap compilation fixes for diag and switch under 2.6.25
...
SVN-Revision: 11231
2008-05-20 22:33:45 +00:00
72d40dec08
Allow package/switch to compile against 2.6.25
...
SVN-Revision: 11138
2008-05-14 15:03:05 +00:00
6a2a1e251b
Check the return values of kmalloc()
...
SVN-Revision: 10599
2008-03-13 15:22:46 +00:00
d65241e13b
fix switch-robo.c compile errors on linux 2.4
...
SVN-Revision: 10539
2008-03-01 15:34:17 +00:00
a9cddc69ec
Fix the roboswitch code for the WRT350N
...
SVN-Revision: 10531
2008-02-27 22:35:41 +00:00
faa14263f5
ssb: Make the GPIO API reentrancy safe.
...
SVN-Revision: 10496
2008-02-19 15:22:17 +00:00
d9e54d1e0b
export switch-core.h to $(STAGING_DIR)
...
SVN-Revision: 10138
2008-01-06 19:28:26 +00:00
e3ecefbd23
fix adm switch misdetection, which led to bogus button events that caused the system to shut down
...
SVN-Revision: 9555
2007-11-16 03:11:09 +00:00
a9d683ca91
major target cleanup. it is now possible to have subtargets that can override many target settings, including arch - merge adm5120, adm5120eb. target profiles still need to be adapted for subtargets
...
SVN-Revision: 8694
2007-09-08 19:55:42 +00:00
e3dc76af1b
fix board name for nvram and switch packages on brcm-2.4 after [8653]
...
SVN-Revision: 8664
2007-09-07 12:54:24 +00:00
34bb4638e7
move package description to a separate definition, remove it when DESCRIPTION=TITLE
...
SVN-Revision: 8659
2007-09-07 08:34:51 +00:00
56231056ea
strip the kernel version suffix from target directories, except for brcm-2.4 (the -2.4 will be included in the board name here). CONFIG_LINUX_<ver>_<board> becomes CONFIG_TARGET_<board>, same for profiles.
...
SVN-Revision: 8653
2007-09-06 16:27:37 +00:00
be0de75a3e
package Makefile cleanup: remove uneeded vars
...
SVN-Revision: 8587
2007-09-03 08:20:36 +00:00
02cd6d278f
use a default VERSION field for kmod packages
...
SVN-Revision: 8575
2007-09-02 16:39:27 +00:00
80840457a5
fix kmod-switch compile on brcm-2.4 ( #1461 )
...
SVN-Revision: 6565
2007-03-14 13:42:21 +00:00
dcfbd5f656
fix up remaining parts for the brcm47xx-2.6 port (tested on wgt634u), nuke the old brcm-2.6 port, close #1312 , #1451
...
SVN-Revision: 6564
2007-03-14 03:37:40 +00:00
bf622ab0ae
add diag and switch support for brcm47xx-2.6
...
SVN-Revision: 6562
2007-03-14 01:19:24 +00:00
c606df6563
cleanup, nuke obsolete 'Kernel drivers' category, convert remaining kmod packages to KernelPackage interface
...
SVN-Revision: 6136
2007-01-20 02:01:53 +00:00
dd03b56357
fix memory leak in switch drivers (patch from #1132 )
...
SVN-Revision: 6011
2007-01-07 14:59:43 +00:00
Jonas Gorski
Hauke Mehrtens
Jo-Philipp Wich
Florian Fainelli
Claudio Mignanti
Felix Fietkau
Nicolas Thill
John Crispin
Peter Denison
Michael Büsch