Renaming an atm etherbride using 'ip link' (via hotplug) is racy since the
original netdev might disappear before br2684ctl has finished appling it's
setting:
local2.notice br2684ctl[1667]: Interface "nas0" created sucessfully
local2.notice br2684ctl[1667]: Communicating over ATM 0.8.35, encapsulation: LLC
kern.info kernel: dsl0: renamed from nas0
kern.err kernel: br2684:br2684_regvcc: tried to attach to non-existent device
local2.err br2684ctl[1667]: Could not configure interface:No such device or address
By passing the final used netdev name to br2684ctl_wrap another race
condition workaround will be enabled again.
Change the lantiq ptm driver to create a netdev with the name dsl as well.
Albeit the rename via 'ip link' works fine so far, using a different
approach for ptm then atm could be confusing.
Signed-off-by: Mathias Kresin <dev@kresin.me>
br2684ctl starts automatically, set up reload triggers, which fire as soon
as a atm driver is loaded. No need to do the reload via the script.
The reload is only required as soon as we can reliable switch between atm
and ptm driver and need to be implemented in a race free way.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add the uci option nameprefix to specifc a target netdev name. Patch the
br2684ctl code to accept and set a netdev name via commandline parameters.
It allows to use the same netdev name for ATM and PTM lines on lantiq
xdsl hardware.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Mathis Kresin <dev@kresin.me>
Enable CONFIG_VFP again which was disabled during the 4.9 -> 4.14 bump.
Boot tested both 32 and 64 bit subtargets using initramfs images with the
qemu-system-arm and qemu-system-aarch64 emulators.
Fixes: aa100b66f2 ("armvirt: bump to v4.14")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
These packages are needed to generate the image, better mark them hidden
so we will activate them based on which boards gets build and they will
be activated always when the board which needs then gets build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These packages are needed to generate the image, better mark them hidden
so we will activate them based on which boards gets build and they will
be activated always when the board which needs then gets build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The fixes following problems
1. changing prefix at91bootstrap to AT91bootstrap will fix the default
selection of at91bootstrap for the selected sama5 subtarget.
2. fixed missing default selection of sama5d4 nand flash for the
selected sama5d4 subtarget.
3. corrected at91bootstrap Title name.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
neon and VFPv4 support is added to this target and uboot-at91 build
fails due to TARGET_CFLAGS -mfloat-abi set to hard. as a fix, setting
uboot-at91 CFLAGS -mfloat-abi=soft.
Fixes: 01cc6bd495 ("at91: sama5: activate fpu")
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Fixes the following dependency error encountered by the buildbots:
Package kmod-w1 is missing dependencies for the following libraries:
hwmon.ko
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
also known as
POGO-V4-A3-02
or
POGO-V4-A3-01
SoC: Marvell 88F6192 800Mhz
SDRAM memory: 128MB
Gigabit ethernet: 1 Marvell 88E1310
Flash memory: 128MB
2 status LEDs (one green one red)
1 "Eject" button on the back (used as "Reset" button)
1 USB 2.0 port (on upper side)
1 sata slot (power + data) for 2.5'' drives (upper side)
2 USB 3.0 ports from a controller on PCIe x1 of the SoC
1 full-size SDcard slot (fits a whole SD card into it)
This device supports the (linux-only) kwboot tool to send
a new uboot over serial console, so it is easy to unbrick
in case the uboot is erased and the device won't boot.
-----
Install instructions:
-----
Since it's not possible to get ssh access to these
devices, the only way to take control is to
solder pins to get TTL serial access.
Case can be opened by removing screws beneath two rubber
feet at back of device, then lifting while prying the
sides of the upper part out to unhook a latch on each
side about 2/3rds of the way toward the front.
Serial connection pins are those labeled "J11", left
of SD as you face SD opening.
Pins are (from left to right, i.e. the first in the list
is the nearest to the SD slot) GND, Rx, Tx.
Do not connect +V pin if you use a USB (self-powered)
TTL-to-USB dongle. Any USB TTL-to-USB converter will work.
Baud rate is 115200, parity "none", databits "8",
flow control "none".
Stock uboot is unable to read ubi partitions (nor usb)
so we will replace it first with our uboot.
Start a TFTP server at IP address 169.254.254.254, and
place the uboot.kwb file in the folder of the server.
Start the serial session and then power up the device.
As soon as you see text on the serial start pressing random
letter keys to stop the boot process.
If you see something like the following line you can proceed:
CE>>
Otherwise if text is still scrolling by you missed the
opportunity, pull the plug and try again.
write
printenv ethaddr
The uboot will write something like this:
ethaddr=00:50:43:00:02:02
This is the device's MAC address, also present in the sticker
under the device.
Write this down as we will need to add it in the
new uboot configuration.
Use the following commands to load the new uboot:
tftp 0x20000 u-boot.kwb
If the uboot confirms that the transfer was successful,
then you can write it to flash with the following commands:
nand erase 0 0x200000
nand write 0x20000 0 0x1c0000
if after the last command the uboot wrote
"xxxx bytes written: OK"
then it was written correctly and we can proceed.
If it did not go well, try again or ask assistence in forums.
Shutting down or rebooting at this time will brick
the device, to unbrick it you will need to use the kwboot
tool from a Linux PC or Virtual Machine.
Now write:
reset
and press enter, the device will reboot and you should see
again text scrolling by.
Press a random key to stop it, and now you should see
pogoplugv4>
We now add the MAC address back, write:
setenv ethaddr '00:50:43:00:02:02'
Confirm that the uboot has understood by writing
printenv ethaddr
If all looks ok, save the setting with
saveenv
At this point the uboot is configured, and we only need to load
the firmware in the flash memory.
Follow the steps below in "Firmware recovery procedure".
----
Firmware recovery procedure
----
The new uboot allows easy recovery from a bad firmware upgrade
where you can't access the device anymore over ssh or luci.
Take a USB flash drive formatted as FAT32, and copy the
initramfs image file in it (it will have "initramfs" in the
file name), then rename it as "initramfs.bin".
Insert the USB drive in the USB 2.0 port of the pogoplug
(the port at the top).
Power up the device, and wait for it to finish booting.
The uboot should find and load the "initramfs.bin"
from usb and if you are connected with serial you should
see the linux kernel boot log (text scrolling by).
Once it is done, press Enter and you will be greeted by
the OpenWRT banner.
If you were not connected with serial just wait a bit and,
you will be able to access it with ssh or luci web interface
(once you find its IP).
The recovery "initramfs" images are run from RAM, so you will
have to do a normal sysupgrade (firmware upgrade) to write
a firmware image to flash memory.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
add an uboot able to boot a kernel in an ubi partition
This uboot also has a "recovery" feature, before
booting from flash it will try to boot a initramfs
image called "initramfs.bin" from a FAT32-formatted
USB drive connected to the USB 2.0 port.
(u-boot lacks drivers for usb 3.0 controllers)
Just rename the initramfs image and place it on
the usb drive, the uboot will load it.
In case there is no USB drive or no such file
is found, the uboot will boot from internal flash.
The whole check takes less than a second, boot times
are not impacted.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Use <manufacturer>_<modelname> as image name.
Use the BOARD_NAME variable to ensure that the former used boardname is
still used as the subdirectory name for the sysupgrade-tar image, to
not break sysupgrade from earlier versions.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Append and enforce image metadata. Remove the device specific image
checks, they are replaced by image metadata.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Build the Seagate GoFlexHome u-boot for the Seagate GoFlexNet as well. The
name clearly indicates that the u-boot can be used for both boards
Build the Zyxel NSA310 u-boot if the NSA310B image is selected.
Signed-off-by: Mathias Kresin <dev@kresin.me>
There is no point in being that specifc in a generic dts covering a range
of boards. Keep only the the generic compat string to use it for a
devicetree based boardname.
Signed-off-by: Mathias Kresin <dev@kresin.me>
No image build code for the Guruplug, Sheevaplug and NSA310S exists. Drop
support for the boards for now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Drop NAND_BLOCKSIZE, UBI_OPTS and UBIFS_OPTS. They are either used by
not supported filesystems or by the legacy image build code.
Add common used options/images to the default build code and override
the options where necessary.
Don't export the kernel image, it isn't required by any board.
While at it, change the file extension for the sysupgrade images to bin.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The TP-Link firmware uses (primary_mac-1) as MAC-address
for the 5GHz WiFi. This applies the same behaviour to LEDE.
Currently, the MAC-address is retrieved from eth1, which
does not exist on the Archer C7 v4. As a result from this,
every C7 v4 with LEDE carries the same MAC-Address on the 5GHz WiFi.
Signed-off-by: David Bauer <mail@david-bauer.net>
There are 3 ethernet ports on Y1. LAN1 on port1, LAN2 on port0 and WAN on
port4.
Use a standalone switch configuration to match this and use the switch
trigger so that LAN LED could indicate the connetction status for both
lan ports correctly.
This patch also drop the internet led configuration, because there is a
WAN led for port4 and eth0.2 isn't always used as WAN.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Use the "low" and "high" values to configure the GPIO as an output with
that initial value. It ensures that the gpio doesn't have a unwanted value
during the time the direction is set to ouput and the actual value is
applied.
We don't need to take care of the GPIO polarity for now, since our
exported GPIOs are always active low.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Start gpio_switch before the boot state is set to up/initialised/done.
This way the exported GPIOs are available at the time rc.local is started.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 4.4.0 is always
false. Remove the obsolete check from mach-rb4xx.c to clean up the code
a bit.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 4.2.0 is always
false. Remove the obsolete check from ag71xx_main.c to clean up the code
a bit.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 3.15.0 is always
false. Remove the obsolete checks from the target specific source files
to clean up the code a bit.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Disable the drivers for the following ethernet switches:
Realtek RTL8306
Realtek RTL8366/8367
Marvell 88E6060 (DSA)
Marvell 88E6063 (DSA)
Also disable the phy driver for Marvell PHYs.
None of the supported RouterBOARDs are using any device
which needs these drivers.
Disable the DSA framework too, because it is not required
by the remaining switch drivers.
This reduces the compressed kernel size by ~20KB.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The Marvell 88E6063 ethernet switch driver depends on the DSA
framework. Add a 'depends on NET_DSA' statement to its Kconfig
entry to state that explicitly.
Fixes the following Kconfig warning:
warning: (NET_DSA_MV88E6060 && NET_DSA_MV88E6063) selects NET_DSA_TAG_TRAILER which has unmet direct dependencies (NET && NET_DSA)
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Previously this was only activated for ADSL, this patch activates the
same setting also for VDSL, this feature is also support for VDSL in the
same way it works for ADSL.
I tested it with DSL FW 5.7.9.5.1.7 against a Broadcom 177.140 DSLCO
(Deutsche Telekom) and saw different data rates and Max. Attainable Data
Rates depending on the ds_snr_offset settings I choose.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The previous commit was incorrectly rebased and referred to a not
yet existing PROJECT_GIT variable.
Fixes: d86a269c1f libubox: update to latest git HEAD
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Mathias Kresin
Martin Schiller
Jo-Philipp Wich
Kevin Darbyshire-Bryant
Hauke Mehrtens
Sandeep Sheriker Mallikarjun
Alberto Bursi
David Bauer
Chuanhong Guo
Gabor Juhos
John Crispin
Stijn Tintel
Matthias Schiffer