OpenWrt uses ancient u-boot thats not reproducible.
There are multiple upstream changes that introduce
reproducible builds like:
859e92b775fd8ebcfacc591eaf621b677c95b6f7
(not used here - the CMD_DATE/TIMESTAMP functionality
seems to be disabled by config)
70d39f57146a6cb94736db39c770c3d95e07bedb
f3f431a712729a1af94d01bd1bfde17a252ff02c
2d9efa1227262249d381ed5d9d341cbdba76e62d
Instead of changing the Makefile too much
this changeset just tries to use the
changes in Makefile from current upstream git f5fd45f
*Should* fix issue reported by reproducible lede page:
https://tests.reproducible-builds.org/lede/lede.html
Compile tested only
(verified w. hexdump & md5sum)
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Tested with VDSL on TP-Link WD8970, I see full 1500-byte PPP data
frames, which end up being 1526 byte Ethernet frames (including
Ethernet+VLAN headers) on the wire.
Fixes: FS#210
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Switch to xz tarball, there's no point pulling two different tarballs of the same source code (tools/libtool uses xz).
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
luci using ustream-mbedtls is extremely slow vs ustream-polarssl.
polarssl alias mbedtls v1 is configured to use NIST prime speed
optimisation, so no longer disable the default optimisation for
mbedtls v2.
Compile & run tested: Archer C7v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
[Jo-Philipp Wich: refresh patch to use common format]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Adds per-host leasetime support
Various bugfixes :
-Prioritize ifname resolving via ubus
-Free interface if ifindex cannot be resolved
-...
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [update mirror sha256]
This fixes the following error when mounting a ext4 filesystem
----
[ 166.240000] EXT4-fs (sda1): Cannot load crc32c driver.
----
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Commit 8f24ee6382 ("uqmi: Add proper IPv6 support") changed the code
to fetch the IPv4 address via QMI by default instead of using DHCP to
make it consistent with the IPv6 codepath.
This breaks on at least some Sierra Wireless cards, where data exchanges
fail to work until the host has fetched a DHCP lease.
Leave v6 as it is, but always use DHCP for v4.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
nf_tproxy_core was removed during 3.12 development with kernel commit
fd158d79d33d3c8b693e3e2d8c0e3068d529c2dc. The code was moved
to xt_TPROXY.c.
Fixes FS#212
Signed-off-by: Mathias Kresin <dev@kresin.me>
Adds the latest patches from Jes Sorensen for rtl8xxxu, which improve
rtl8732bu, rtl8192eu and rtl8188eu support.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* Change git packages to xz
* Update mirror checksums in packages where they are used
* Change a few source tarballs to xz if available upstream
* Remove unused lines in packages we're touching, requested by jow- and blogic
* We're relying more on xz-utils so add official mirror as primary source, master site as secondary.
* Add SHA256 checksums to multiple git tarball packages
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Quote resolveip hostname argument to avoid bad shell injections.
While at it fix pattern match logic in case multiple IPv6 addresses
are returned for a hostname as they're seperated by newline by
resolveip and not a white space
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Adds u-boot for the at91 platform and a couple of boards.
The build honours COPTS to benefit from fortify source et al.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Now that the uhttpd init script can generate certificates using openssl as
well, update the section name and related comment to be more generic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Before a configuration is generated, an empty file is created to store
it in. (required by UCI)
If something happens during config generation
(power cut, interruption, ..) an empty file exists and it is never
regenerated again, causing some daemons to fail starting
(NTPD, logread, ..)
Fix this by also generating new configs if a critical file
is empty.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The kmod-sound-hda-core module attempts to package snd-hda-core.ko which
does not exist in Linux 3.18, therfore only use it for kernels >= 4.1
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Support the usage of the OpenSSL command-line tool for generating
the SSL certificate for uhttpd. Traditionally 'px5g' based on
PolarSSL (or mbedTLS in LEDE), has been used for the creation.
uhttpd init script is enhanced by adding detection of an installed
openssl command-line binary (provided by 'openssl-util' package),
and if found, the tool is used for certificate generation.
Note: After this patch the script prefers to use the OpenSSL tool
if both it and px5g are installed.
This enables creating a truly OpenSSL-only version of LuCI
without dependency to PolarSSL/mbedTLS based px5g.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Prior to kernel 4.4, the hda-intel module depends on the hda-controller
utility submodule so bundle it for the older kernel versions.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This patch removes the non-working wifi driver filter for
the wifi detection script.
I figured that rather than replacing ${2:-$DRIVERS} with
${1:-$DRIVERS}, it would be better to remove it. Nobody
needed it in the previous years.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
vfat filesystem fails to mount due to missing codepages with
factory-formatted flash drives. Depend on cp437 iso8559-1 and
utf8 nls modules as this covers most factory-formatted vfat
filesystems.
Signed-off-by: Daniel Dickinson <lede@cshore.thecshore.com>
This patch set adds support for PCI Intel HD Audio
sound devices. This is useful for multimedia packages
in the packages feed that one may use to create audio
servers.
Signed-off-by: Daniel Dickinson <lede@cshore.thecshore.com>
We have to remove the FPU check, it will run in an endless loop on LEDE
when compile without FPU emulation support.
The second patch fixes this problem: valgrind: mmap(0x400000, 303104)
failed in UME with error 22 (Invalid argument).
valgrind still does not support mips16, build LEDE without mips16 support.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The nf_reject_* and nf_nat_masquerade_* modules are moved into the
corresponding kmod-nf- packages. Appropriate dependencies are added to the
kmod-nft- packages.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Since the kernel makefile is using .ONESHELL, we need to add -e to
.SHELLFLAGS so errors are not ignored.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Fix rt_names build failure when FORTIFY_SOURCE disabled.
Include limits.h which otherwise gets automatically included
by fortify headers.
Solves FS #194
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Now that the firmware for BCM43430 has been submitted to linux-firmware use it
and remove RPiDistro package.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This patch moves the ath10k firmware packages to the firmware submenu
in the buildroot, where it belongs.
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
Use firmware version 10.2.4.70.54 from kvalo's git repository. The old
version (even though it's version number is greater) is an old version
from September 2015.
Using only the firmware versions from kvalo's git repo is recommended,
because those are tested by QCA's internal QCA.
The QCA988X directory received a small reorganization as a "hw2.0"
subdirectory was added - this patch also takes care of that as
board.bin was moved to that subdirectory.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
For 64-bit capable systems, a symbolic link is set up for /lib64 to point to
/lib, so make sure the installation goes into /lib, irrespective of where the C
library files come from in an external toolchain.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
There is a separate package kmod-crypto-echainiv for echainiv.ko. Selecting
both packages led to a conflict, so remove the file from kmod-crypto-iv.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This fixes bug that could cause WARNING on every add_key/del_key call.
It also replaces WARNING with a simple message. They may still occur
e.g. on station going out of range and A-MPDU stall in the firmware.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
A bug fix which included a CRL sanity check was added to OpenSSL 1.1.0
but was omitted from OpenSSL 1.0.2i. As a result any attempt to use
CRLs in OpenSSL 1.0.2i will crash with a null pointer exception.
Patches applied upstream:
* 301-fix_no_nextprotoneg_build.patch
* 302-Fix_typo_introduced_by_a03f81f4.patch
Security advisory: https://www.openssl.org/news/secadv/20160926.txt
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Adds Google's mirrors as primary source and kernel.org as fallback.
Discussed in #lede-dev on Freenode
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Within the Lua binding, use the same logic as the command line interface for
reporting the used WPA ciphers. Instead of printing the intersection of
pairwise and group ciphers, report both group and pairwise ciphers.
This fixes a case where a connection which uses CCMP for pairwise and TKIP
as groupwise cipher is getting reported as using the NONE cipher.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The Linux kernel uses two distinct fields to denote the routing table ID in
use by network routes; the 8 bit `rtm_table` member of `struct rtmsg` and the
32 bit `RTA_TABLE` netlink attribute.
If a routing table ID is larger than 255, the `RT_TABLE` attribute must be used
and the `rtm_table` field has to be set to the special `RT_TABLE_UNSPEC` value.
This commit adds a patch which...
- switches the *_n2a() and *_a2n() functions of rt_names.c to use dynamically
sized, name-sorted arrays instead of fixed arrays limited to 1024 slots in
order to support IDs up to 65535
- adds proper handling of high table IDs to iprule.c and iproute.c when
adding, removing and dumping ip rules and network routes
After this change, the Busybox ip applet fully supports IP rules with high ID
numbers, using the same logic as the full iproute2.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Remove an invalid local variable declaration in the tunnel update subshell
invocation. Local declarations outside of function scopes are illegal since
the Busybox update to version 1.25.0 .
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
All these patches are in wireless-drirvers-next. There is support for
hidden SSID, few new devices and many fixes.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Now that we know that the password is in /etc/shadow and not in
/etc/passwd, we can properly fix the logic for the empty password check.
Only 'root::' is an empty password, 'root❌' and 'root:!:' allow no
password login at all.
This fixes the empty password warning still showing after the root password
has been locked using 'passwd -l root' (e.g. to allow public-key auth
only).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Configurations without shadow passwords have been broken since the removal
of telnet: as the default entry in /etc/passwd is not empty (but rather
unset), there will be no way to log onto such a system by default. As
disabling shadow passwords is not useful anyways, remove this configuration
option.
The config symbol is kept (for a while), as packages from feeds depend on
it.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Uboot-mvebu isn't a real package, which will break the image builder
when it tries to install it during the packing step. Instead of cleafog
selecting it through its default packages, make it default to m if the
clearfog profile is selected.
This will ensure it is always build, but never added to the rootfs. This
fixes creating images for clearfog with IB.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
The clearfog image requires u-boot, so package it into KDIR to make sure
it is available in imageBuilder.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Running prepare_rootfs on TARGET_DIR deletes the opkg state when
CONFIG_CLEAN_IPKG is enabled, making the per-device rootfs package install
fail.
To avoid this, create a copy of the TARGET_DIR before prepare_rootfs is run
and use this as basis for per-device rootfs generation.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
br_netfilter.ko and the corresponding Kconfig symbol are already provided
by kmod-br-netfilter, which is a dependency of kmod-ebtables.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Local variable declarations outside of functions are illegal since the Busybox
update to v1.25.0, therfore remove them from the appropriate places.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Update the linux-firmware package in order to force the buildbots to fetch the
proper mirrored version.
Currently each builder has its own copy of the linux-firmware checkout staged
in its own dl/, since the package was updated before the mirrored copy has
been uploaded. The builders then subsequently uploaded their own copy instead,
leading to md5sum mismatches since each clone produces different tarballs.
By bumping the package to a new version and uploading the mirrored archive
with the proper md5sum beforehand, the builders will fetch that instead and
not upload their own copies.
To properly solve that problem in the future we need to ensure that packed
checkouts become reproducable.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Since the md5sum of the mirrored Git clone archive has been set in the Makefile
before that particular archive was uploaded to the source mirror, the buildbots
uploaded their own, different copy instead invalidating the mirror md5sum for
anyone else.
In order to fix the mismatch, update the md5sum to reflect the archive being
present on the download server.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The Annex A firmware will be updated to:
05.08.01.08.01.06_05.08.00.0B.01.01_osc
The Annex B firmware will be updated to:
05.07.09.09.00.06_05.07.04.04.00.02_osc
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Some devices (like the Cisco Meraki Z1 Cloud Managed Teleworker Gateway)
need to be able to initialize the PCIe wifi device. Normally, this is done
during the early stages of booting linux, because the necessary init code
is read from the memory mapped SPI and passed to pci_enable_ath9k_fixup.
However,this isn't possible for devices which have the init code for the
Atheros chip stored on NAND in an UBI volume. Hence, this module can be
used to initialze the chip when the user-space is ready to extract the
init code.
Martin Blumenstingl made a few fixes and added support for lantiq:
kernel: owl-loader: add support for OWL emulation PCI devices
kernel: owl-loader: don't re-scan the bus when ath9k_pci_fixup failed
kernel: owl-loader: use dev_* instead of pr_* logging functions
kernel: owl-loader: auto-generate the eeprom filename as fallback
kernel: owl-loader: add a debug message when swapping the eeprom data
kernel: owl-loader: add missing newlines in log messages
kernel: owl-loader: add support for the lantiq platform
These patches have been integrated. Thanks!
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
The default configuration might not be suitable for
every use case. Add options to enable/disable additional
options.
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Match sections allow to set a tag specified by the option networkid if the client
sends an option and optionally the option value specified by the match option.
The force option will convert the dhcp-option to force-dhcp-option if set to 1 in
the dnsmasq config if options are specified in the dhcp_option option.
config match
option networkid tag
option match 12,myhost
option force 1
list dhcp_option '3,192.168.1.1'
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
A padding to align a message should not only be added between
different attributes of a netlink message, but also at the end of the
message to pad it to the correct size.
Without this patch the following command does not work and returns an
error code:
ip link add type nlmon
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now that we have firmwares separated and brcm2708 being the only target that
actually selects SDIO support, avoid selecting all firmwares by default.
sunxi should select the proper firmwares once SDIO support is enabled and
tested.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Using few packages will allow saving some space by decreasing rootfs
size.
Moreover there are more firmware files that may require packaging and
even more to come later.
This can especially useful now, with per device rootfs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
clean up usb gadget support:
- rename gadget modules so that they appear together and are easier to
identify as gadget modules
- make usb-lib-composite and usb-gadget hidden as there is no point in
selecting those without gadget drivers that require them as deps
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Now we have firmwares separated and bcm53xx selecting required ones make
use of it to actually save that rootfs space.
Other targets using brcmfmac (brcm2708 and sunxi) use SDIO interface and
firmware so they don't won't be affected.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Using few packages will allow saving some space by decreasing rootfs
size. Dropping 43602a1 firmware saves 316 580 B. Dropping 4366b1 saves
468 188 B.
Moreover there are more firmware files that may require packaging and
even more to come later (e.g. 4366c0).
This can especially useful now, with per device rootfs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Permit users of the full variant to disable the NO_ID *.bind pseudo
domain masking.
Defaulted 'on' in all variants.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
As security precaution and to limit the attack surface based on
the version reported by tools like nmap mask out the dropbear
version so the version is not visible anymore by snooping on the
wire. Version is still visible by 'dropbear -V'
Based on a patch by Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [remove trailing _]
Don't expose dnsmasq version & other data to clients via the *.bind
pseudo domain. This uses a new 'NO_ID' compile time option which has been
discussed and submitted upstream.
This is an alternate to replacing version with 'unknown' which affects
the version reported to syslog and 'dnsmasq --version'
Run time tested with & without NO_ID on Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
e2fsprogs would fail linking with external toolchains which would not be able
to find several dependencies, explicit them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Regression introduced by 3481d0d dnsmasq: run as dedicated UID/GID
dnsmasq is unable to remove its own pidfile as /var/run/dnsmasq is owned
by root and now dnsmasq runs as dnsmasq:dnsmasq. Change directory
ownership to match.
dnsmasq initially starts as root, creates the pidfile, then drops to
requested non-root user. Until this fix dnsmasq had insufficient
privilege to remove its own pidfile.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Add a dependency on DRIVER_11W_SUPPORT in order to enable the IEEE
802.11w functionality in hostapd.
Signed-off-by: Petko Bordjukov <bordjukov@gmail.com>
oneshot trigger configurations for LEDs are created, but the on/off
timing configurations are ignored. generate_config is correctly creating
oneshot configs, but the later led script doesn't recognise the trigger
details.
Fixes: c0c3f2d4c9 leds: support oneshot as well as timer triggers
Signed-off-by: Karl Palsson <karlp@etactica.com>
Enable CONFIG_PROCD_ZRAM_TMPFS compatibility via two changes to list_cpu_idx():
* detect if /tmp is being used by /dev/zram0; if yes, offset initial value by 1 to skip first zram device.
* hot-add /dev/zram1, if not already present.
Signed-off-by: Conn O'Griofa >connogriofa@gmail.com>
Add a patch to backport 5185c91385d73cdf79836eb8548e4726e43ae831
from Linux 4.8 adding USB2380 support to the NET2280 driver and
create an OpenWrt menu option to select it as a module.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This allows kobs-ng to flash the SPL successfully on the 4.4 kernel used by
the Gateworks IMX boards supporting NAND. The previous version of kobs-ng
worked with the 3.14 kernel but will brick a board making its SPL unbootable
for the 4.4 kernel.
See http://trac.gateworks.com/wiki/ventana/bootloader#nandspl for instructions
on updating the SPL from Linux.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
power save response frames can go through the old tx path, and the tid
needs to be set for sequence numbers to be assigned correctly.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This reverts commit 763f5d7873.
Currently the vfork() code path in opkg is broken and relies on unsupported
ftello() / fseeko() operations on pipes - we need to restructure the code
before we can reconsider this approach.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This reverts commit 02e3c718e9.
Currently the vfork() code path in opkg is broken and relies on unsupported
ftello() / fseeko() operations on pipes - we need to restructure the code
before we can reconsider this approach.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Tested briefly on Netgear r7800. Firmware failed to load on first
boot, but then it worked after that and I could not reproduce the
failure.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This tool can periodically check for ath10k firmware crashes.
If it finds a crash, it will package up the binary crash dump,
some OS level things like dmesg, lspci, etc into a tar file.
It then notifies the user about the crash and asks them to report
the bug to the appropriate email address.
This is most useful when used with ath10k-ct driver and
CT ath10k firmware, but it should also report issues with stock
ath10k driver and firmware in case one has appropriate contacts
to debug them.
This tool could be extended later for other modules/bugs/etc.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The iwinfo library might get compiled with different backends, depending on
the driver selection of the current target, so mark it as nonshared to avoid
broken libiwinfo support on other targets with same cpu architecture but
different wireless driver types.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The ATH9K_STATION_STATISTICS kernel config variable enables some extra
statistics that are useful for debugging (in particular with the airtime
fairness patches enabled). This adds that kernel config when selecting
ath9k debugging.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
This uses GFP_DMA32 for firmware swap. Fixes issue on x86-64 with
QCA 9984 chipset when host system does not have vt-d enabled.
Also tested on linksys ea8500 with 9980 chipset.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The default configuration might not be suitable for
every use case. Add options to enable/disable additional
options.
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Without any in-tree users enabled the Kernel's build process doesn't
actually build those modules. Enable some potential in-tree users
during Kernel build, so out-of-tree modules can depend on them.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
With the default priority of 0, the DEU algos would be overlapped
by the generic algos (if available).
To fix this, set the cra_priority of the hardware algos to the
recommended value of 300/400.
Signed-off-by: Martin Schiller <mschiller@tdt.de>
Now that snapshot builds are only publishing SHA-256 checksums, it makes
sense to ship an appropriate utility for verification.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
PPP daemon can be put into persist mode meaning the
daemon will not exit after a connection gets terminated
but will instead try to reopen the connection.
The re-initiation after the link has been terminated
can be controlled via holdoff; this is helpfull in
scenarios where a BRAS is in denial of service mode
due to link setup requests after a BRAS has gone down
Following uci parameters have been added :
persist (boolean) : Puts the ppp daemon in persist mode
maxfail (integer) : Number of consecutive fail attempts which
puts the PPP daemon in exit mode
holdoff (interget) : Specifies how many seconds to wait
before re-initiating link setup after it has been terminated
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
src/linksys_bootcount.c misses to include stdint.h.
Apparently musl doesn't mind and includes this header by default,
but glibc does not and causes the build to fail.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
tools/env/fw_env.c misses to include stdint.h.
Apparently musl doesn't mind and includes this header by default,
but glibc does not and causes the build to fail.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
* Only parse interfaces that are up during init_config (as the
script depends on this to determine the proper IP/subnet range)
* Add reload interface triggers for samba-designated interfaces
* Force full service restart upon config change to ensure Samba
binds to new interfaces (sending HUP signal doesn't work)
* Rename "interface" variable to "samba_iface" and move into
global scope
Needed to fix Samba connectivity for clients connecting from a
different LAN subnet (e.g. pseudobridge configurations) due to the
'bind interfaces only' setting.
Signed-off-by: Conn O'Griofa <connogriofa@gmail.com>
When PKG_CONFIG_LIBDIR was unset in the environment, the configure
script was deducing the PKG_CONFIG_LIBDIR from the location of the
pkg-config binary, which doesn't make a lot of sense, and isn't done
by other autotools based packages.
Patch imported from the Buildroot project:
https://github.com/buildroot/buildroot/blob/master/package/ncurses/0001-fixup-pkg-config-handling.patch
Also refresh patches while we're at.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Due to an empty pi_ifname in the generic failsafe setup, the deconfig
never removed the failsafe networking interface, causing broken
networking later on.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Also configure the switch based on the failsafe config, and create the
failsafe interface as tagged if necessary.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
In preparation of properly setting up vlans and switches, add
support for configuring failsafe on a vlan tagged interface.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Move preinit interface and ip config to its own function to allow
calling it from more than one place.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Instead of board_detect generating the config as a side effect, let
config_generate call board_detect as needed.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
- Security: Message printout was vulnerable to format string injection.
If specific usernames including "%" symbols can be created on a system
(validated by getpwnam()) then an attacker could run arbitrary code as root
when connecting to Dropbear server.
A dbclient user who can control username or host arguments could potentially
run arbitrary code as the dbclient user. This could be a problem if scripts
or webpages pass untrusted input to the dbclient program.
- Security: dropbearconvert import of OpenSSH keys could run arbitrary code as
the local dropbearconvert user when parsing malicious key files
- Security: dbclient could run arbitrary code as the local dbclient user if
particular -m or -c arguments are provided. This could be an issue where
dbclient is used in scripts.
- Security: dbclient or dropbear server could expose process memory to the
running user if compiled with DEBUG_TRACE and running with -v
The security issues were reported by an anonymous researcher working with
Beyond Security's SecuriTeam Secure Disclosure www.beyondsecurity.com/ssd.html
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Among other things, this compiles out support for peer caching.
The feature did not seem to work well in my testing of AP mode,
and totally breaks my own special use of station mode.
Briefly tested on ea8500.
Signed-off-by: Ben Greear <greearb@candelatech.com>
ath10k-ct driver was using bad defaults for 9980 if user
had not specified a fwcfg file to over-ride them.
Also, support configurable station-kickout-threshold,
which might work around issues with flakey connections.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [fix PKG_VERSION]
9pfs is used by kvm to share files between host and guest,
add proper config option to enable it.
Signed-off-by: Matteo Croce <matteo.croce@canonical.com>
RADIUS accounting can be used even when RADIUS authentication is not
used. Move the accounting configuration outside of the EAP-exclusive
sections.
Signed-off-by: Petko Bordjukov <bordjukov@gmail.com>
The pi_* variables and the fs_failsafe_wait_timeout variable are set by
the CONFIG_TARGET_PREINIT_* config options. No need to maintain the same
values twice.
All other fs_ variables were never used.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Change the error message about missing SSL support to be more explicit by
mentioning required package names.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Changes include:
* Higher maximum transmit power in the 5170-5250 band of the BG
regdomain
* Introduction of the CU regdomain
* Introduction of the 5725-5875 band (short-range devices) in the DE
regdomain
* Introduction of 60 GHz channels 1-4 in the KR regdomain
* Introduction of the 5725-5875 band (short-range devices) in the NL
regdomain
Signed-off-by: Petko Bordjukov <bordjukov@gmail.com>
sysupgrade immediately reboots after flashing an image and doesn't
allow to unmount filesystems. At least in case the image used for
sysupgrade is stored on a FAT formatted usb flash drive, the following
warning is printed during the next mount of the flash drive:
FAT-fs (sda1): Volume was not properly unmounted. Some data may be
corrupt. Please run fsck.
Although a data corruption during read operations is unlikely, there is
no need to scare the users.
Signed-off-by: Mathias Kresin <dev@kresin.me>
/etc/init.d/boot tried to create /dev/root based on the kernel's
cmdline which won't work on any recent targets. Remove that code now
that fstools can detect the mounted rootfs based on
/proc/self/mountinfo and /dev/root was long gone anyway.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Targets that need switch drivers should select them in their kernel
config. This prevents some bloat from creeping into targets that don't
need switchdev/dsa
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Network drivers typically allocate memory in atomic context. For that to
be reliable, there needs to be enough free memory. Set the value
heuristically based on the total amount of system RAM.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If option ist not set then ipv6 is still enabled on this Interface.
Check if variable is zero will fix this issue.
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
multiple invocation of dnsmasq script (e.g. by procd and hotplugd)
might cause procd to restart dnsmasq with an incomplete config file.
Config file generation might take quite a long time on larger configs
due ubus calls for each listening interface...
Signed-off-by: Ulrich Weber <ulrich.weber@riverbed.com>
Emits an initial event after the first link-up of a force_link
interface. This is needed for making the dnsmasq dhcp check more
reliable
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Open/close triggers array around service_triggers call to make using
multiple triggers easier to deal with.
The API was quite confusing, because some functions contained implicit
trigger open/close calls and some didn't.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Passing the hostname is currently broken in since the shipped busybox includes this commit:
https://git.busybox.net/busybox/commit/networking/udhcp/dhcpc.c?id=2017d48c0d70bef8768efb42909e605ea8eb5a21
Before:
Sun Jan 31 18:11:32 2016 daemon.notice netifd: Interface 'wan' is now down
Sun Jan 31 18:11:32 2016 daemon.notice netifd: Interface 'wan' is setting up now
Sun Jan 31 18:11:32 2016 daemon.notice netifd: wan (18158): udhcpc: option -h NAME is deprecated, use -x hostname:NAME
Sun Jan 31 18:11:32 2016 daemon.notice netifd: wan (18158): udhcpc: malformed hex string 'WR150'
After:
Sun Jan 31 18:11:33 2016 daemon.notice netifd: wan (18169): udhcpc (v1.23.2) started
Sun Jan 31 18:11:33 2016 daemon.notice netifd: wan (18169): Sending discover...
Sun Jan 31 18:11:33 2016 daemon.notice netifd: wan (18169): Sending select for xxx.yyy.zzz.xyz...
Sun Jan 31 18:11:33 2016 daemon.notice netifd: wan (18169): Lease of xxx.yyy.zzz.xyz obtained, lease time 600
Signed-off-by: Merlijn Wajer <merlijn@wizzup.org>
Treat 'relayd' as an essential service to avoid connection interruptions during sysupgrade on devices configured as a pseudobridge.
Signed-off-by: Conn O'Griofa <connogriofa@gmail.com>
Fixes duplicate ubiblock entries being listed and improves
find_mount_point to also match against a block device's
major:minor numbers (needed e.g. for /dev/root).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Previous implementation was blocking the init and
breaking halt/reboot/sysupgrade (reported by Daniel Golle)
v2: use procd logging, use set -e + trap for error handling
Signed-off-by: Etienne CHAMPETIER <champetier.etienne@gmail.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
This firmware has been lightly tested on non LEDE system
to date, and will be undergoing further testing and development.
Allow users to easily install this on their LEDE system as
they prefer.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The patch needed for this commit has been sent upstream:
https://github.com/openssl/openssl/pull/1155
Signed-off-by: Dirk Feytons <dirk.feytons@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [add back bf and srp]
NPN has been superseded by ALPN so NPN is disabled by default
The patch has been sent to OpenSSL for inclusion, see
https://github.com/openssl/openssl/pull/1100
Signed-off-by: Dirk Feytons <dirk.feytons@gmail.com>
This patch gets rid of the booke watchdog kmod package.
Instead the affected boards will enable it in their
kernel configs.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
There seems to be a situation in which a rebuild of libpcap.so is triggered
in the install step of the libpcap Makefile. libpcap.so is the wrong
target, leading to the build failure reported in [1].
Fix the dependency of install-shared-so to $(SHAREDLIB) so the build can
succeed in this case.
[1] https://dev.openwrt.org/ticket/19894
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This lets one use the CT ath10k driver instead of the built-in
ath10k driver from the upstream kernel (or backports).
This should be a drop-in replacement, as well as enabling
better CT firmware support.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This reverts commit 31e5ed4152.
I've noticed some weird powersave related issues with this commit.
Revert until they've been fixed.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Removed socket options = TCP_NODELAY IPTOS_LOWDELAY
TCP_NODELAY (disables Nagle algorithm) is default since samba2.
IPTOS_LOWDELAY sets DSCP 0x10 coding (CS2)
The alternate IPTOS_THROUGHPUT sets DSCP 0x08 coding (CS1)
CS1 is a scavenger class, whilst CS2 is more OAM/interactive
(SNMP,SSH,syslog)
Using CS2 is definitely an abuse of DSCP classification, CS1 less so
however even if the ISP takes note of DSCP codings having a default that
sets traffic to CS2 is wrong. Better to use the default Best Effort
class.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
iftop would display portions of mac address with large ffffff prefixes.
Make if_hw_addr type consistent.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Move logging command line option to uci:
option verbose [0]/1/2 - mono-syllabic/verbose/noisy
Previously handled as 'OPTIONS' in .init script however variable
was ignored so never worked.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
To work correctly hostapd requires wireless driver to allow interfaces
removal. It was working with brcmfmac only partially. Firmware for
BCM43602 got some special hack (feature?) that allowed removing all
interfaces by disabling mbss mode. It wasn't working with BCM4366
firmware and remaining interfaces were preventing hostapd from starting
again.
Those patches add support for "interface_remove" firmware method which
works with BCM4366 firmware and they make it finally possible to use
BCM4366 & brcmfmac & multiple interfaces.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
There are multiple prism54/p54 firmware versions for different
drivers and devices. Therefore, assigning the package version
of all the different firmware packages on the old prism54
firmware could break if any of the p54 firmwares are updated
and we need to roll out new packages.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[removed PKG_VERSION]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Removed some options which are default anyway and added bind interfaces
only which causes the interfaces line to actually have an effect. Can be
verified with netstat.
Signed-off by: Rosen Penev <rosenp@gmail.com>
px5g has been listed as a blocker for switching to new mbedtls
as the default, therefore make and mbedtls variant of px5g so
that an new mbedtls-only image can be created.
Signed-off-by: Daniel Dickinson <lede@daniel.thecshore.com>
This reverts commit abf0768131.
The description is wrong, there is no recursive dependency here. The
conditions were added intentionally to avoid bogus build dependencies.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Commit d9b20a6f35 (SVN r48426) changed the
mac80211 phy lookup logic to strip the platform/ directory component from
the phy path specification.
Fix iwinfo to follow that logic by trying to lookup phys both with and
without "platform/" prefix.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
On OS X systems, the compilation of e2fsprogs fails at subst.c due to a
missing sys/stat.h include:
subst.c:333:14: error: variable has incomplete type 'struct stat'
struct stat stbuf;
^
subst.c:333:9: note: forward declaration of 'struct stat'
struct stat stbuf;
^
subst.c:392:8: warning: implicit declaration of function 'fstat' is invalid in C99
[-Wimplicit-function-declaration]
if (fstat(fd, &stbuf) == 0) {
^
subst.c:438:12: warning: implicit declaration of function 'fchmod' is invalid in C99
[-Wimplicit-function-declaration]
(void) fchmod(ofd, 0444);
^
2 warnings and 1 error generated.
make[3]: *** [subst.o] Error 1
Declare the nescessary HAVE_SYS_STAT_H macro to include the required header in
order to avoid the undeclared stat structure.
Tested-By: David Thornley <david.thornley@touchstargroup.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Two variants incorrectly include themselves in
conditional depends on ssl libraries, which results
in a recursive dependency.
Signed-off-by: Daniel Dickinson <lede@daniel.thecshore.com>
This allows gpiolib to re-use ath9k's devicetree node as GPIO
controller.
Example:
ath9k: ath9k@0 {
#gpio-cells = <2>;
gpio-controller;
}
Now the ath9k node can be used just like any other GPIO controller:
gpios = <&ath9k 1 GPIO_ACTIVE_HIGH>;
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This enables ath9k's built-in GPIO controller for all chip versions
(instead of an explicit whitelist). This also allows us to get rid of
some duplicate code between hw.c and gpio.c because hw.c already
determines the number of GPIOs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This folds 550-ath9k_add_ar9280_gpio_chip.patch into
548-ath9k_enable_gpio_chip.patch because the former patch only extends
code which is introduced in the latter.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Use first caldata for devices without OTP. The driver uses the caldata
instead of the board.bin data anyway
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Small cleanup. I initially though /dev/kmsg was used for dmsg(and journald
on desktops) but this seems not to be the case. dmsg is still accessible
as non-root(gives output) which begs the question what does this do? Some
googling reveals that permissions are set to 600 for some embedded systems
while 644 for others. I can't find any justification for the latter. Might
as well err on the side of caution.
Signed-off by: Rosen Penev <rosenp@gmail.com>
This package is a custom build(like ubi-utils) of mtd-utils from infradead.org
It is required to work with Mikrotik NAND based devices
Signed-off-by: Sergey Sergeev <adron@yapic.net>
This adds this commit from normal libnl to libnl-tiny:
2dbc1ca76c
commit 2dbc1ca76c5b82c40749e609eb83877418abb006
Author: dima <dima.ky@gmail.com>
Date: Wed Oct 13 17:53:34 2010 +0300
Generic Netlink multicast groups support
I have a patch against commit d378220c96c3c8b6f27dca33e7d8ba03318f9c2d
extending libnl with a facility to receive generic netlink messages sent
to multicast groups.
Essentially it add one new function genl_ctrl_resolve_grp which
prototype looks like this
int genl_ctrl_resolve_grp(struct nl_sock *sk, const char *family_name,
const char *grp_name)
It resolves the family name and the group name to group id. Then
the returned id can be used in nl_socket_add_membership to subscribe
to multicast messages.
Besides that it adds two more functions
uint32_t nl_socket_get_peer_groups(struct nl_sock *sk)
void nl_socket_set_peer_groups(struct nl_sock *sk, uint32_t groups)
allowing to modify the socket peer groups field. So it's possible to
multicast messages from the user space using the legacy interface.
Looks like there is no way (or I was not able to find one?) to modify
the netlink socket destination group from the user space, when the
group id is greater then 32.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cosmetic style fix]
The pps-ldisc kernel module supports Pulse-Per-Second connected with the CD (Carrier Detect) pin.
Signed-off-by: Stephen Walker <stephendwalker+github@gmail.com>
This changes the default permissions for /dev entries to be more similar to
a desktop distro. Taken from the defaults of Arch Linux and Ubuntu. Also
changed some that were nonsensical. For example, all 660 permissions on
desktop distros were of the form root:x where x is something other than
root. As such, 660 is useless for LEDE where the specific group is missing.
audio seems to be the only group that isn't.
Signed-off by: Rosen Penev <rosenp@gmail.com>
This commit:
1) seed /dev/urandom with the saved seeds as early as possible
(see /lib/preinit/81_urandom_seed)
2) save a seed at /etc/urandom.seed if it doesn't exists
3) save a new seed each boot at "system.@system[0].urandom_seed"
(see /etc/init.d/urandom_seed)
We use getrandom() so we are sure /dev/urandom pool is initialized
Seed size is 512 bytes (ie /proc/sys/kernel/random/poolsize / 8)
it's the same size as in ubuntu 14.04 and all systemd systems
Seeding /dev/urandom doesn't change entropy estimation, so we still have
"random: ubus urandom read with 4 bits of entropy available"
messages in the logs, but we can now ignore them if
after "urandom-seed: Seeding with ..." message
Saving a new seed on each boot is disabled by default to avoid too much
writes without user consent
v2: log preinit messages to /dev/kmsg
v3: use non generic function name for logging, as /lib/preinit/ files
are all sourced together in /etc/preinit
v4: after a lot of discussion on the ML, use a uci config param
v5: config param is now the path of the seed
Signed-off-by: Etienne CHAMPETIER <champetier.etienne@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
OpenWrt enables XATTR support pretty much universally, therefore
for filesystems that a loaded as modules also enable XATTR support
so that there are no unexpected missing capabilities.
Signed-off-by: Daniel Dickinson <lede@daniel.thecshore.com>
Instead of downloading the firmware for prism54 devices in the
wireless.mk do it in an extra package Makefile. To ship the complete
source code Intel ships our modified OpenWrt/LEDE + the content of the
dl directory. We do not want to have any files in the dl/ directory
which are not needed to build our images. The prism54 gets downloaded
every time independently of building kmod-net-prism54 or not. When it
is in a own package it only gets downloaded when the firmware package
is selected.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Following fixes are included in the latest version:
-Script is launched with incorrect action
-Possible buffer overflows
-Lots of minor bugfixes
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
COBALT is a hybrid codel/blue algo combining best elements of both.
Exhibits improved behaviour in presence of abuse from unresponsive flows
handled by 'blue', whereas responsive flows are still handled by codel.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Cake AQM is experimenting with a codel/blue hybrid AQM COBALT instead
of just using codel alone. This patch updates tc to cope with some new
stats produced by COBALT.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
By default dnsmasq uses the time function; which returns the time since
Epoch; to retrieve the current time. On boards which have no realtime
clock this can lead to side effects when the time is synced via ntp
as the "time wrap" forces dhcp leases to be considered as expired.
By enabling the broken realtime clock build switch dnsmasq uses the
times utility which returns the number of clock tick.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
[Jo-Philipp Wich: change symbol name, add sym to PKG_CONFIG_DEPENDS]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
93d5629a introduced a build failure on older platforms (<4.4)
because bmp085 is a boolean and not a tristate.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
add BMP085 and BMP180 pressure sensors
this driver supports the SPI and I2C and
older chips (BMP280 is supported by iio subsystem)
issue found when cleaning up omap/config
found while writing this patch that a
similar patch was submitted in June/July 2014 but not integrated
only compile tested
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
The PDU length of incoming LLC frames is set to the total skb payload size
in __ieee80211_data_to_8023() of net/wireless/util.c which incorrectly
includes the length of the IEEE 802.11 header.
The resulting LLC frame header has a too large PDU length, causing the
llc_fixup_skb() function of net/llc/llc_input.c to reject the incoming
skb, effectively breaking STP.
Solve the problem by properly substracting the IEEE 802.11 frame header size
from the PDU length, allowing the LLC processor to pick up the incoming
control messages.
Special thanks to Gerry Rozema for tracking down the regression and proposing
a suitable patch.
Fixes FS#24.
References:
https://bugs.lede-project.org/index.php?do=details&task_id=24
Reported-by: Gerry Rozema <gerryr@rozeware.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Upstream OpenSSL hardening work introduced a change in shared code that
causes polarssl / mbedtls builds to break when no --tls-cipher is specified.
Import the upstream fix commit as patch until the next OpenVPN release gets
released and packaged.
Reported-by: Sebastian Koch <seb@metafly.info>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
With the addition of /etc/os-release patching lldpd to use
/etc/openwrt_release and to have the initscript use
/etc/openwrt_release and/or /etc/openwrt_version becomes
unnecessary.
Signed-off-by: Daniel Dickinson <lede@daniel.thecshore.com>
There are 2 issues fixed by this patch:
- UDP checksum is computed incorrectly, the used pseudo IP header
contains transport protocol 6 iso 17
- on big endian arches the UDP/TCP checksum is incorrectly
computed when payload length is odd
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [refresh patch]
The copy on the mirror has a different md5sum as specified in this
package Makefile. The content of the file on the mirror is the same as
in the checkout so just update our md5sum.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of downloading the firmware from some website take it from
linux-firmware package and do not download it separately any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ebtables code relies on the `-nostartfiles` linker argument to execute the
extension modules' `_init()` functions automatically which is not working
reliably across all supported targets and gcc versions.
Running an ebtables executable linked this way just crashes with a segmentation
fault at runtime on program startup, e.g. on ARM architectures.
In order to fix the issue ...
- remove the use of the -nostartfiles linker flag
- rename the init procedures to a generic name without implicit semantics
- explicitely annotate those init procedures as constructors
The patch has been taken from the Alpine Linux distribution at
http://git.alpinelinux.org/cgit/aports/tree/main/ebtables/fix-extension-init.patch
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Dirk Neukirchen
David Woodhouse
Daniel Engberg
John Crispin
Kevin Darbyshire-Bryant
Felix Fietkau
diizzyy
Hans Dedecker
daniel
Mathias Kresin
Álvaro Fernández Rojas
Hans Dedecker
Ben Whitten
Jo-Philipp Wich
Koen Vandeputte
Hannu Nyman
Christian Lamparter
Daniel Dickinson
Hauke Mehrtens
Matthias Schiffer
Stijn Segers
Martin Blumenstingl
Florian Fainelli
Rafał Miłecki
Magnus Kroken
Rosen Penev
Jonas Gorski
Hauke Mehrtens
Andreas Schultz
Tim Harvey
Petko Bordjukov
Johannes Römer
Alexis Green
Karl Palsson
Conn O'Griofa
Zhao Gang
Gabe Rodriguez
Ben Greear
Ralph Sennhauser
Toke Høiland-Jørgensen
Ash Benz
Daniel Golle
Martin Schiller
Josua Mayer
Matteo Croce
Imre Kaloz
Lucian Cristian
Florian Eckert
Ulrich Weber
Merlijn Wajer
Etienne CHAMPETIER
Dirk Feytons
Piotr Dymacz
Rafał Miłecki
Daniel Dickinson
Zoltan HERPAI
Sergey Sergeev
Stephen Walker
Hans Dedecker
Alexander Couzens
Alin Năstac